diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/AdderII.h | 226 |
1 files changed, 226 insertions, 0 deletions
diff --git a/include/configs/AdderII.h b/include/configs/AdderII.h new file mode 100644 index 0000000..c2cff23 --- /dev/null +++ b/include/configs/AdderII.h @@ -0,0 +1,226 @@ +/****************************************************************************** +* A collection of structures, addresses, and values associated with +* the Motorola 850T AdderIIF board. Copied from the FADS stuff. +* Magnus Damm added defines for 8xxrom and extended bd_info. +* Helmut Buchsbaum added bitvalues for BCSRx +* +* Copyright (c) 1998 Dan Malek (dmalek@jlc.net) +******************************************************************************* +* 2003-JUL: The AdderII is using the following physical memorymap: +******************************************************************************* +* FA200000 -> FA20FFFF : IMAP internal in the cpu +* FE000000 -> FE400000 : flash connected to CS0, setup by 8xxrom +* 00000000 -> 00800000 : sdram setup by 8xxrom +*******************************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <mpc8xx_irq.h> + +#define CONFIG_MPC860 1 +#define CONFIG_MPC860T 1 +#define CONFIG_ADDERII 1 + +/* CPU Clock speed */ +#define MPC8XX_FACT 12 /* Multilpy by 12 */ +#define MPC8XX_XIN 4000000 /* 4MHz */ +#define MPC8XX_HZ ( MPC8XX_FACT * MPC8XX_XIN ) + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ +#define CONFIG_SDRAM_50MHZ 1 + + +/* Default Serial Console, baudrate */ +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#define CONFIG_BAUDRATE 38400 +#define CONFIG_LOADS_ECHO 1 + +/* FEC Ethernet controller configurations */ +#define CONFIG_FEC_ETH 1 +#define CONFIG_NET_MULTI 1 +#define FEC_ENET 1 + +/* Interrupt level assignments. +*/ +#define FEC_INTERRUPT SIU_LEVEL3 /* FEC interrupt */ + +/* Older kernels need clock in MHz newer in Hz */ +#define CONFIG_CLOCKS_IN_MHZ 1 + +/* Monitor Functions */ +#define CONFIG_COMMANDS ( CFG_CMD_FLASH | \ + CFG_CMD_MEMORY| \ + CFG_CMD_NET | \ + CFG_CMD_ENV | \ + CFG_CMD_PING | \ + CFG_CMD_SDRAM ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* Configuration Settings */ +#define CFG_PROMPT "=>" /* Monitor Command Prompt */ + +#if ( CONFIG_COMMANDS & CFG_CMD_KGDB ) +#define CFG_CBSIZE 1024 /* Console I/P buffer size */ +#else +#define CFG_CBSIZE 256 +#endif + +#define CFG_PBSIZE ( CFG_CBSIZE + sizeof( CFG_PROMPT ) + 16 ) + /* Print buffer size */ + +#define CFG_MAXARGS 16 /* Max number of cmd args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot args buffer size */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CFG_MEMTEST_START 0x00100000 /* Mem test works on */ +#define CFG_MEMTEST_END 0x00800000 /* 1 ... 8MB in SDRAM */ + +#define CFG_LOAD_ADDR 0x00100000 +#define CFG_HZ 1000 + +/****************************************************************************** +** Low level configuration settings. +** ( adderss mappings, register init values, etc. ) +** You should know what you are doing if you make changes here. +******************************************************************************/ +/* Start address for the final memory configuration set up by startup code +** Please note that CFG_SDRAM_BASE must start at 0 +*/ + +#define CFG_SDRAM_BASE 0x00000000 + +#define CFG_FLASH_BASE 0xFE000000 +#define CFG_FLASH_SIZE (( uint ) ( 4 * 1024 * 1024 )) /* 4MB */ +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MONITOR_LEN ( 256 << 10 ) /* 256 KByte */ +#define CFG_MALLOC_LEN ( 384 << 10 ) /* 384 KByte SDRAM rsvd */ + /* malloc() usage */ +/** +** For booting Linux, the board info and command line data +** have to be in the first 8 MB of memory, since this is +** the maximum mapped by the Linux kernel during initialization. +**/ +#define CFG_BOOTMAPSZ ( 8 << 20 ) /* Initial Memory map for Linux */ + +/****************************************************************************** +** Flash Organization +******************************************************************************/ + +#define CFG_MAX_FLASH_BANKS 1 /* Max no of flash mem banks */ +#define CFG_MAX_FLASH_SECT 71 /* Max no of sec on 1 chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Erase flash timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Write flash timeout (ms) */ + +/****************************************************************************** +** U-BOOT Environment variables in Flash +******************************************************************************/ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x00040000 +#define CFG_ENV_SIZE 0x10000 /* 64KBytes env space */ +#define CFG_ENV_SECT_SIZE 0x10000 + +/****************************************************************************** +** Cache Configuration +******************************************************************************/ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if ( CONFIG_COMMANDS & CFG_CMD_KGDB ) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/****************************************************************************** +** Internal memory mapped register +******************************************************************************/ +#define CFG_IMMR 0xFA200000 +#define CFG_IMMR_SIZE (( uint) ( 62 * 1024 )) /* 64 KByte res */ + +/* Definitions for initial stack pointer and data area ( in DPRAM ) */ + +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x2F00 /* end of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 +#define CFG_GBL_DATA_OFFSET ( CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE ) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + + + +/* SIU Module Configuration Register */ +#define CFG_SIUMCR ( SIUMCR_AEME | SIUMCR_MLRC01 | SIUMCR_DBGC10 ) + +/****************************************************************************** +** SYPCR - System protection and control +** SYPCR - can be written only once after reset +******************************************************************************/ +#if defined( CONFIG_WATCHDOG ) +#define CFG_SYPCR ( SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | \ + SYPCR_SWF | SYPCR_SWE | SYPCR_SWRI | \ + SYPCR_SWP ) +#else +#define CFG_SYPCR ( SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | \ + SYPCR_SWF | SYPCR_SWP ) +#endif + +/* TBSCR - Time Base Status and Control Register */ +#define CFG_TBSCR ( TBSCR_REFA | TBSCR_REFB | TBSCR_TBE ) + +/* PISCR - Periodic Interrupt Status and Control */ +#define CFG_PISCR ( PISCR_PS | PISCR_PITF ) + +/* PLPRCR - PLL, Low-Power, and Reset Control Register */ +#define CFG_PLPRCR ((( MPC8XX_FACT - 1 ) << PLPRCR_MF_SHIFT ) | \ + PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST ) + +/* SCCR - System Clock and reset Control Register */ +#define SCCR_MASK SCCR_EBDF11 +#define CFG_SCCR ( SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \ + SCCR_DFBRG00 | SCCR_DFNL000| SCCR_DFNH000 | \ + SCCR_DFLCD000 | SCCR_DFALCD00 ) +#define CFG_DER 0 + +/****************************************************************************** +** Because of the way the 860 starts up and assigns CS0 the +** entire address space, we have to set the memory controller +** differently. Normally, you write the option register +** first, and then enable the chip select by writing the +** base register. For CS0, you must write the base register +** first, followed by the option register. +******************************************************************************/ +/** + ** Memory Controller Definitions + ** BR0/1/2... and OR0/1/2... +*/ +/* For AdderII BR0 FLASH */ + +#define CFG_REMAP_OR_AM 0xFF800000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ + +/* Flash Timings: ACS = 11, TRLX = 1, CSNT = 0, SCY = 7 */ +#define CFG_OR_TIMING_FLASH ( OR_ACS_DIV2 | OR_BI | OR_SCY_7_CLK | OR_TRLX ) + +#define CFG_OR0_REMAP ( CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH ) + +#define CFG_OR0_PRELIM CFG_OR0_REMAP +#define CFG_BR0_PRELIM (( CFG_FLASH_BASE & BR_BA_MSK ) | \ + BR_PS_16 | BR_V ) + +/* For AdderII BR1 SDRAM */ + +#define CFG_PRELIM_OR1_AM 0xFF800000 +#define CFG_OR1_REMAP ( CFG_PRELIM_OR1_AM | OR_CSNT_SAM | OR_ACS_DIV2 ) +#define CFG_OR1_PRELIM ( CFG_PRELIM_OR1_AM | OR_CSNT_SAM | OR_ACS_DIV2 ) +#define CFG_BR1_PRELIM ( CFG_SDRAM_BASE | BR_MS_UPMA | BR_V ) + + +/******************************************************************************* +* Internal Definitions Boot Flags +*******************************************************************************/ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +#endif +/* __CONFIG_H */ + |