summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/TQM5200.h31
-rw-r--r--include/configs/TQM85xx.h7
-rw-r--r--include/configs/cmc_pu2.h11
-rw-r--r--include/configs/gth2.h195
-rw-r--r--include/configs/spieval.h28
-rw-r--r--include/configs/trab.h6
6 files changed, 212 insertions, 66 deletions
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 6020998..6b8759f 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -37,7 +37,6 @@
#define CONFIG_TQM5200 1 /* ... on TQM5200 module */
#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */
#define CONFIG_STK52XX 1 /* ... on a STK52XX base board */
-#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */
#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
@@ -83,7 +82,7 @@
#define CONFIG_PCI_IO_SIZE 0x01000000
#define CONFIG_NET_MULTI 1
-#define CONFIG_EEPRO100
+#define CONFIG_EEPRO100 1
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#endif /* CONFIG_STK52XX */
@@ -192,16 +191,6 @@
#undef CONFIG_BOOTARGS
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX "-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX "-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX "-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX "\0"
-#endif
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
@@ -218,7 +207,7 @@
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"bootfile=/tftpboot/tqm5200/uImage\0" \
"load=tftp 200000 ${u-boot}\0" \
- "u-boot=/tftpboot/tqm5200/u-boot.bin" CONFIG_U_BOOT_SUFFIX \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
"update=protect off FC000000 FC05FFFF;" \
"erase FC000000 FC05FFFF;" \
"cp.b 200000 FC000000 ${filesize};" \
@@ -284,13 +273,6 @@
#endif
/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
- CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST { CFG_I2C_SLAVE }
-#endif
-
#if defined (CONFIG_MINIFAP)
#undef I2C_ADDR_LIST
#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
@@ -493,13 +475,9 @@
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE 0x80000 /* 512 kByte */
-#else /* CONFIG_CS_AUTOCONF */
#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
-#endif
#define CFG_CS2_CFG 0x0004D930
#endif
@@ -507,8 +485,7 @@
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
- defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
#define SM501_FB_BASE 0xE0000000
#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index 18197f2..da6946b 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -177,6 +177,13 @@
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+/* PS/2 Keyboard */
+#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */
+#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */
+#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */
+#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */
+#define CONFIG_BOARD_EARLY_INIT_R 1
+
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
diff --git a/include/configs/cmc_pu2.h b/include/configs/cmc_pu2.h
index 46280f7..572a70f 100644
--- a/include/configs/cmc_pu2.h
+++ b/include/configs/cmc_pu2.h
@@ -108,7 +108,7 @@
/* still about 20 kB free with this defined */
#define CFG_LONGHELP
-#define CONFIG_BOOTDELAY 3
+#define CONFIG_BOOTDELAY 1
#ifdef CONFIG_HARD_I2C
#define CONFIG_COMMANDS \
@@ -206,15 +206,6 @@ struct bd_info_ext {
#error CONFIG_USE_IRQ not supported
#endif
-#define CFG_DEVICE_NULLDEV 1 /* enble null device */
-#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n"
-#define CONFIG_AUTOBOOT_STOP_STR "R" /* default password */
-
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"net_nfs=tftp ${loadaddr} ${bootfile};run nfsargs addip addcons " \
"addmtd;bootm\0" \
diff --git a/include/configs/gth2.h b/include/configs/gth2.h
new file mode 100644
index 0000000..77d2d56
--- /dev/null
+++ b/include/configs/gth2.h
@@ -0,0 +1,195 @@
+/*
+ * (C) Copyright 2005
+ * Thomas.Lange@corelatus.se
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * This file contains the configuration parameters for the gth2 board.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#define CONFIG_MIPS32 1 /* MIPS32 CPU core */
+#define CONFIG_GTH2 1
+#define CONFIG_AU1X00 1 /* alchemy series cpu */
+
+#define CONFIG_AU1000 1
+
+#define CONFIG_MISC_INIT_R 1
+
+#define CONFIG_ETHADDR DE:AD:BE:EF:01:02 /* Ethernet address */
+
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */
+
+#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */
+
+#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */
+
+#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */
+
+#define CONFIG_BAUDRATE 115200
+
+/* valid baudrates */
+#define CFG_BAUDRATE_TABLE { 115200 }
+
+/* Only interrupt boot if space is pressed */
+/* If a long serial cable is connected but */
+/* other end is dead, garbage will be read */
+#define CONFIG_AUTOBOOT_KEYED 1
+#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n"
+#define CONFIG_AUTOBOOT_DELAY_STR "d"
+#define CONFIG_AUTOBOOT_STOP_STR " "
+
+#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+#define CONFIG_BOOTARGS "panic=1"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "addmisc=setenv bootargs $(bootargs) " \
+ "ethaddr=$(ethaddr) \0" \
+ "netboot=bootp;run addmisc;bootm\0" \
+ ""
+
+/* Boot from Compact flash partition 2 as default */
+#define CONFIG_BOOTCOMMAND "ide reset;disk 0x81000000 0:2;run addmisc;bootm"
+
+#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \
+ ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \
+ CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_LOADB | CFG_CMD_ELF | \
+ CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT ))
+
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "GTH2 # " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args*/
+
+#define CFG_MALLOC_LEN 128*1024
+
+#define CFG_BOOTPARAMS_LEN 128*1024
+
+#define CFG_MHZ 500
+
+#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */
+
+#define CFG_SDRAM_BASE 0x80000000 /* Cached addr */
+
+#define CFG_LOAD_ADDR 0x81000000 /* default load address */
+
+#define CFG_MEMTEST_START 0x80100000
+#define CFG_MEMTEST_END 0x83000000
+
+#define CONFIG_HW_WATCHDOG 1
+
+/*-----------------------------------------------------------------------
+ * FLASH and environment organization
+ */
+#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT (128) /* max number of sectors on one chip */
+
+#define PHYS_FLASH 0xbfc00000 /* Flash Bank #1 */
+
+/* The following #defines are needed to get flash environment right */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_MONITOR_LEN (192 << 10)
+
+#define CFG_INIT_SP_OFFSET 0x400000
+
+/* We boot from this flash, selected with dip switch */
+#define CFG_FLASH_BASE PHYS_FLASH
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT (2 * CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT (2 * CFG_HZ) /* Timeout for Flash Write */
+
+#define CFG_ENV_IS_NOWHERE 1
+
+/* Address and size of Primary Environment Sector */
+#define CFG_ENV_ADDR 0xB0030000
+#define CFG_ENV_SIZE 0x10000
+
+#define CONFIG_FLASH_16BIT
+
+#define CONFIG_NR_DRAM_BANKS 2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_MEMSIZE_IN_BYTES
+
+/*---ATA PCMCIA ------------------------------------*/
+#define CFG_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */
+
+#define CFG_PCMCIA_MEM_ADDR 0x20000000
+#define CFG_PCMCIA_IO_BASE 0x28000000
+#define CFG_PCMCIA_ATTR_BASE 0x30000000
+
+#define CONFIG_PCMCIA_SLOT_A
+
+#define CONFIG_ATAPI 1
+#define CONFIG_MAC_PARTITION 1
+
+/* We run CF in "true ide" mode or a harddrive via pcmcia */
+#define CONFIG_IDE_PCMCIA 1
+
+/* We only support one slot for now */
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_RESET /* reset for ide not supported */
+
+#define CFG_ATA_IDE0_OFFSET 0
+
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_IO_BASE
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET 0
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET 0
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET 0x0200
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 16384
+#define CFG_ICACHE_SIZE 16384
+#define CFG_CACHELINE_SIZE 32
+
+#define GPIO_CACONFIG (1<<0)
+#define GPIO_DPACONFIG (1<<6)
+#define GPIO_ERESET (1<<11)
+#define GPIO_EEDQ (1<<17)
+#define GPIO_WDI (1<<18)
+#define GPIO_RJ1LY (1<<22)
+#define GPIO_RJ1LG (1<<23)
+#define GPIO_LEDCLK (1<<29)
+#define GPIO_LEDD (1<<30)
+#define GPIO_CPU_LED (1<<31)
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index 96cb6e4..9ebb51e 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -191,16 +191,6 @@
#undef CONFIG_BOOTARGS
-#if defined (CONFIG_TQM5200_AA)
-# define CONFIG_U_BOOT_SUFFIX "-AA\0"
-#elif defined (CONFIG_TQM5200_AB)
-# define CONFIG_U_BOOT_SUFFIX "-AB\0"
-#elif defined (CONFIG_TQM5200_AC)
-# define CONFIG_U_BOOT_SUFFIX "-AC\0"
-#else
-# define CONFIG_U_BOOT_SUFFIX "\0"
-#endif
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"rootpath=/opt/eldk/ppc_6xx\0" \
@@ -217,7 +207,7 @@
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"bootfile=/tftpboot/tqm5200/uImage\0" \
"load=tftp 200000 ${u-boot}\0" \
- "u-boot=/tftpboot/tqm5200/u-boot.bin" CONFIG_U_BOOT_SUFFIX \
+ "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \
"update=protect off FC000000 FC05FFFF;" \
"erase FC000000 FC05FFFF;" \
"cp.b 200000 FC000000 ${filesize};" \
@@ -283,13 +273,6 @@
#endif
/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB)
-#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
- CFG_I2C_SLAVE }
-#elif defined (CONFIG_TQM5200_AC)
-#define I2C_ADDR_LIST { CFG_I2C_SLAVE }
-#endif
-
#if defined (CONFIG_MINIFAP)
#undef I2C_ADDR_LIST
#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \
@@ -478,13 +461,9 @@
* SRAM - Do not map below 2 GB in address space, because this area is used
* for SDRAM autosizing.
*/
-#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
#define CFG_CS2_START 0xE5000000
-#ifdef CONFIG_TQM5200_AB
-#define CFG_CS2_SIZE 0x80000 /* 512 kByte */
-#else /* CONFIG_CS_AUTOCONF */
#define CFG_CS2_SIZE 0x100000 /* 1 MByte */
-#endif
#define CFG_CS2_CFG 0x0004D930
#endif
@@ -492,8 +471,7 @@
* Grafic controller - Do not map below 2 GB in address space, because this
* area is used for SDRAM autosizing.
*/
-#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \
- defined (CONFIG_CS_AUTOCONF)
+#if defined (CONFIG_CS_AUTOCONF)
#define SM501_FB_BASE 0xE0000000
#define CFG_CS1_START (SM501_FB_BASE)
#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */
diff --git a/include/configs/trab.h b/include/configs/trab.h
index 85ee756..8f71acf 100644
--- a/include/configs/trab.h
+++ b/include/configs/trab.h
@@ -160,7 +160,6 @@
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_FAT | \
- CFG_CMD_JFFS2 | \
CFG_CMD_NFS | \
CFG_CMD_SNTP | \
CFG_CMD_USB )
@@ -174,7 +173,6 @@
CFG_CMD_DATE | \
CFG_CMD_DHCP | \
CFG_CMD_FAT | \
- CFG_CMD_JFFS2 | \
CFG_CMD_NFS | \
CFG_CMD_SNTP | \
CFG_CMD_USB )
@@ -384,10 +382,10 @@
#define MTDIDS_DEFAULT "nor0=0"
/* production flash layout */
-#define MTDPARTS_DEFAULT "mtdparts=0:32k(Firmware1)ro," \
+#define MTDPARTS_DEFAULT "mtdparts=0:16k(Firmware1)ro," \
"16k(Env1)," \
"16k(Env2)," \
- "320k(Firmware2)ro," \
+ "336k(Firmware2)ro," \
"896k(Kernel)," \
"5376k(Root-FS)," \
"1408k(JFFS2)," \
generated by cgit v1.1 at 2024-12-30 12:50:26 +0000