diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/ls1012a_common.h | 145 | ||||
-rw-r--r-- | include/configs/ls1012aqds.h | 191 |
2 files changed, 336 insertions, 0 deletions
diff --git a/include/configs/ls1012a_common.h b/include/configs/ls1012a_common.h new file mode 100644 index 0000000..ccd94ec --- /dev/null +++ b/include/configs/ls1012a_common.h @@ -0,0 +1,145 @@ +/* + * Copyright 2016 Freescale Semiconductor + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LS1012A_COMMON_H +#define __LS1012A_COMMON_H + +#define CONFIG_FSL_LAYERSCAPE +#define CONFIG_FSL_LSCH2 +#define CONFIG_LS1012A +#define CONFIG_GICV2 + +#define CONFIG_SYS_HAS_SERDES + +#include <asm/arch/config.h> +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_SUPPORT_RAW_INITRD + +#define CONFIG_DISPLAY_BOARDINFO_LATE + +#define CONFIG_SYS_TEXT_BASE 0x40100000 + +#define CONFIG_SYS_FSL_CLK +#define CONFIG_SYS_CLK_FREQ 100000000 +#define CONFIG_DDR_CLK_FREQ 125000000 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F 1 + +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) + +#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +/* Generic Timer Definitions */ +#define COUNTER_FREQUENCY CONFIG_SYS_CLK_FREQ/4 /* 25MHz */ + +/* CSU */ +#define CONFIG_LAYERSCAPE_NS_ACCESS + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) + +/*SPI device */ +#ifdef CONFIG_QSPI_BOOT +#define CONFIG_SYS_QE_FW_IN_SPIFLASH +#define CONFIG_SYS_FMAN_FW_ADDR 0x400d0000 +#define CONFIG_ENV_SPI_BUS 0 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_MAX_HZ 1000000 +#define CONFIG_ENV_SPI_MODE 0x03 +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_FSL_SPI_INTERFACE +#define CONFIG_SF_DATAFLASH + +#define CONFIG_FSL_QSPI +#define QSPI0_AMBA_BASE 0x40000000 +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_SPI_FLASH_BAR + +#define FSL_QSPI_FLASH_SIZE (1 << 24) +#define FSL_QSPI_FLASH_NUM 2 + +/* + * Environment + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_ENV_SIZE 0x40000 /* 256KB */ +#define CONFIG_ENV_OFFSET 0x200000 /* 2MB */ +#define CONFIG_ENV_SECT_SIZE 0x40000 +#endif + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_MXC +#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */ +#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* Command line configuration */ +#define CONFIG_CMD_ENV +#undef CONFIG_CMD_IMLS + +#define CONFIG_ARCH_EARLY_INIT_R + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_HWCONFIG +#define HWCONFIG_BUFFER_SIZE 128 + +#define CONFIG_DISPLAY_CPUINFO + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "initrd_high=0xffffffff\0" \ + "verify=no\0" \ + "hwconfig=fsl_ddr:bank_intlv=auto\0" \ + "loadaddr=0x80100000\0" \ + "kernel_addr=0x100000\0" \ + "ramdisk_addr=0x800000\0" \ + "ramdisk_size=0x2000000\0" \ + "fdt_high=0xffffffffffffffff\0" \ + "initrd_high=0xffffffffffffffff\0" \ + "kernel_start=0xa00000\0" \ + "kernel_load=0xa0000000\0" \ + "kernel_size=0x2800000\0" \ + "console=ttyAMA0,38400n8\0" + +#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ + "earlycon=uart8250,mmio,0x21c0500" +#define CONFIG_BOOTCOMMAND "sf probe 0:0; sf read $kernel_load "\ + "$kernel_start $kernel_size && "\ + "bootm $kernel_load" +#define CONFIG_BOOTDELAY 10 + +/* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_MAXARGS 64 /* max command args */ + +#define CONFIG_PANIC_HANG +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +#include <asm/fsl_secure_boot.h> + +#endif /* __LS1012A_COMMON_H */ diff --git a/include/configs/ls1012aqds.h b/include/configs/ls1012aqds.h new file mode 100644 index 0000000..2d84095 --- /dev/null +++ b/include/configs/ls1012aqds.h @@ -0,0 +1,191 @@ +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __LS1012AQDS_H__ +#define __LS1012AQDS_H__ + +#include "ls1012a_common.h" + + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 +#define CONFIG_NR_DRAM_BANKS 2 +#define CONFIG_SYS_SDRAM_SIZE 0x40000000 + +#define CONFIG_SYS_MMDC_CORE_CONTROL_1 0x05180000 +#define CONFIG_SYS_MMDC_CORE_CONTROL_2 0x85180000 + +/* + * QIXIS Definitions + */ +#define CONFIG_FSL_QIXIS + +#ifdef CONFIG_FSL_QIXIS +#define CONFIG_QIXIS_I2C_ACCESS +#define CONFIG_SYS_I2C_FPGA_ADDR 0x66 +#define QIXIS_LBMAP_BRDCFG_REG 0x04 +#define QIXIS_LBMAP_SWITCH 6 +#define QIXIS_LBMAP_MASK 0xf7 +#define QIXIS_LBMAP_SHIFT 0 +#define QIXIS_LBMAP_DFLTBANK 0x00 +#define QIXIS_LBMAP_ALTBANK 0x08 +#define QIXIS_RST_CTL_RESET 0x41 +#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 +#define QIXIS_RCFG_CTL_RECONFIG_START 0x21 +#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 +#endif + +/* + * I2C bus multiplexer + */ +#define I2C_MUX_PCA_ADDR_PRI 0x77 +#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */ +#define I2C_RETIMER_ADDR 0x18 +#define I2C_MUX_CH_DEFAULT 0x8 +#define I2C_MUX_CH_CH7301 0xC +#define I2C_MUX_CH5 0xD +#define I2C_MUX_CH7 0xF + +#define I2C_MUX_CH_VOL_MONITOR 0xa + +/* +* RTC configuration +*/ +#define RTC +#define CONFIG_RTC_PCF8563 1 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/ +#define CONFIG_CMD_DATE + +/* EEPROM */ +#define CONFIG_ID_EEPROM +#define CONFIG_CMD_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#define CONFIG_SYS_EEPROM_BUS_NUM 0 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 + + +/* Voltage monitor on channel 2*/ +#define I2C_VOL_MONITOR_ADDR 0x40 +#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 +#define I2C_VOL_MONITOR_BUS_V_OVF 0x1 +#define I2C_VOL_MONITOR_BUS_V_SHIFT 3 + +/* DSPI */ +#define CONFIG_FSL_DSPI1 +#define CONFIG_DEFAULT_SPI_BUS 1 + +#define CONFIG_CMD_SPI +#define MMAP_DSPI DSPI1_BASE_ADDR + +#define CONFIG_SYS_DSPI_CTAR0 1 + +#define CONFIG_SYS_DSPI_CTAR1 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\ + DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(0)) +#define CONFIG_SPI_FLASH_SST /* cs1 */ + +#define CONFIG_SYS_DSPI_CTAR2 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\ + DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(0) | DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(0)) +#define CONFIG_SPI_FLASH_STMICRO /* cs2 */ + +#define CONFIG_SYS_DSPI_CTAR3 (DSPI_CTAR_TRSZ(7) | DSPI_CTAR_PCSSCK_1CLK |\ + DSPI_CTAR_PASC(0) | DSPI_CTAR_PDT(0) | \ + DSPI_CTAR_CSSCK(2) | DSPI_CTAR_ASC(0) | \ + DSPI_CTAR_DT(0)) +#define CONFIG_SPI_FLASH_EON /* cs3 */ + +#define CONFIG_SF_DEFAULT_SPEED 10000000 +#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 +#define CONFIG_SF_DEFAULT_BUS 1 +#define CONFIG_SF_DEFAULT_CS 0 + +/* +* USB +*/ +/* EHCI Support - disbaled by default */ +/*#define CONFIG_HAS_FSL_DR_USB*/ + +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_FSL +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#endif + +/*XHCI Support - enabled by default*/ +#define CONFIG_HAS_FSL_XHCI_USB + +#ifdef CONFIG_HAS_FSL_XHCI_USB +#define CONFIG_USB_XHCI +#define CONFIG_USB_XHCI_FSL +#define CONFIG_USB_XHCI_DWC3 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 +#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE +#endif + +/* MMC */ +#define CONFIG_MMC +#ifdef CONFIG_MMC +#define CONFIG_FSL_ESDHC +#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 +#define CONFIG_GENERIC_MMC +#define CONFIG_DOS_PARTITION +#endif + +/* SATA */ +#define CONFIG_LIBATA +#define CONFIG_SCSI +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_CMD_SCSI +#define CONFIG_DOS_PARTITION +#define CONFIG_BOARD_LATE_INIT + +#define CONFIG_SYS_SATA AHCI_BASE_ADDR + +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCIE1 /* PCIE controller 1 */ +#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */ +#define FSL_PCIE_COMPAT "fsl,ls1043a-pcie" + +#define CONFIG_SYS_PCI_64BIT + +#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 +#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ +#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 +#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ + +#define CONFIG_SYS_PCIE_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 +#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ + +#define CONFIG_SYS_PCIE_MEM_BUS 0x08000000 +#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x04000000 +#define CONFIG_SYS_PCIE_MEM_SIZE 0x80000000 /* 128M */ + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW +#define CONFIG_CMD_PCI + +#define CONFIG_CMD_MEMINFO +#define CONFIG_CMD_MEMTEST +#define CONFIG_SYS_MEMTEST_START 0x80000000 +#define CONFIG_SYS_MEMTEST_END 0x9fffffff + +#define CONFIG_MISC_INIT_R + +#endif /* __LS1012AQDS_H__ */ |