diff options
Diffstat (limited to 'include/configs')
-rw-r--r-- | include/configs/omap3_evm.h | 272 | ||||
-rw-r--r-- | include/configs/omap3_evm_common.h | 286 | ||||
-rw-r--r-- | include/configs/omap3_evm_quick_mmc.h | 89 | ||||
-rw-r--r-- | include/configs/omap3_evm_quick_nand.h | 91 |
4 files changed, 270 insertions, 468 deletions
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h index 1726a3e..52a24d3 100644 --- a/include/configs/omap3_evm.h +++ b/include/configs/omap3_evm.h @@ -96,11 +96,279 @@ #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +/* + * High level configuration options + */ +#define CONFIG_OMAP /* This is TI OMAP core */ +#define CONFIG_OMAP_GPIO +#define CONFIG_OMAP_COMMON +/* Common ARM Erratas */ +#define CONFIG_ARM_ERRATA_454179 +#define CONFIG_ARM_ERRATA_430973 +#define CONFIG_ARM_ERRATA_621766 + +#define CONFIG_SDRC /* The chip has SDRC controller */ + +#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */ +#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */ + +/* + * Clock related definitions + */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK >> 1) + +/* + * OMAP3 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. + */ +#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ + +/* Size of environment - 128KB */ +#define CONFIG_ENV_SIZE (128 << 10) + +/* Size of malloc pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) + +/* + * Physical Memory Map + * Note 1: CS1 may or may not be populated + * Note 2: SDRAM size is expected to be at least 32MB + */ +#define CONFIG_NR_DRAM_BANKS 2 +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 + +/* Limits for memtest */ +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ + 0x01F00000) /* 31MB */ + +/* Default load address */ +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) + /* ----------------------------------------------------------------------------- - * Include common board configuration + * Hardware drivers * ----------------------------------------------------------------------------- */ -#include "omap3_evm_common.h" + +/* + * NS16550 Configuration + */ +#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ + +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK + +/* + * select serial console configuration + */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */ +#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ + 115200} + +/* + * I2C + */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX + +/* + * PISMO support + */ +/* Monitor at start of flash - Reserve 2 sectors */ +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) + +/* Start location & size of environment */ +#define ONENAND_ENV_OFFSET 0x260000 +#define SMNAND_ENV_OFFSET 0x260000 + +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ + +/* + * NAND + */ +/* Physical address to access NAND */ +#define CONFIG_SYS_NAND_ADDR NAND_BASE + +/* Physical address to access NAND at CS0 */ +#define CONFIG_SYS_NAND_BASE NAND_BASE + +/* Max number of NAND devices */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BUSWIDTH_16BIT +/* Timeout values (in ticks) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) +#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) + +/* Flash banks JFFS2 should use */ +#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ + CONFIG_SYS_MAX_NAND_DEVICE) + +#define CONFIG_SYS_JFFS2_MEM_NAND +#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 + +#define CONFIG_JFFS2_NAND +/* nand device jffs2 lives on */ +#define CONFIG_JFFS2_DEV "nand0" +/* Start of jffs2 partition */ +#define CONFIG_JFFS2_PART_OFFSET 0x680000 +/* Size of jffs2 partition */ +#define CONFIG_JFFS2_PART_SIZE 0xf980000 + +/* + * USB + */ +#ifdef CONFIG_USB_OMAP3 + +#ifdef CONFIG_USB_MUSB_HCD + +#define CONFIG_USB_STORAGE +#define CONGIG_CMD_STORAGE + +#ifdef CONFIG_USB_KEYBOARD +#define CONFIG_SYS_USB_EVENT_POLL +#define CONFIG_PREBOOT "usb start" +#endif /* CONFIG_USB_KEYBOARD */ + +#endif /* CONFIG_USB_MUSB_HCD */ + +#ifdef CONFIG_USB_MUSB_UDC +/* USB device configuration */ +#define CONFIG_USB_DEVICE +#define CONFIG_USB_TTY +#define CONFIG_SYS_CONSOLE_IS_IN_ENV + +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "EVM" +#endif /* CONFIG_USB_MUSB_UDC */ + +#endif /* CONFIG_USB_OMAP3 */ + +/* ---------------------------------------------------------------------------- + * U-Boot features + * ---------------------------------------------------------------------------- + */ +#define CONFIG_SYS_MAXARGS 16 /* max args for a command */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of Console IO buffer */ +#define CONFIG_SYS_CBSIZE 512 + +/* Size of print buffer */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) + +/* Size of bootarg buffer */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +#define CONFIG_BOOTFILE "uImage" + +/* + * NAND / OneNAND + */ +#if defined(CONFIG_CMD_NAND) +#define CONFIG_SYS_FLASH_BASE NAND_BASE + +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET +#elif defined(CONFIG_CMD_ONENAND) +#define CONFIG_SYS_FLASH_BASE ONENAND_MAP +#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP +#endif + +#if !defined(CONFIG_ENV_IS_NOWHERE) +#if defined(CONFIG_CMD_NAND) +#define CONFIG_ENV_IS_IN_NAND +#elif defined(CONFIG_CMD_ONENAND) +#define CONFIG_ENV_IS_IN_ONENAND +#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET +#endif +#endif /* CONFIG_ENV_IS_NOWHERE */ + +#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET + +#if defined(CONFIG_CMD_NET) + +/* Ethernet (SMSC9115 from SMSC9118 family) */ +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 + +/* BOOTP fields */ +#define CONFIG_BOOTP_SUBNETMASK 0x00000001 +#define CONFIG_BOOTP_GATEWAY 0x00000002 +#define CONFIG_BOOTP_HOSTNAME 0x00000004 +#define CONFIG_BOOTP_BOOTPATH 0x00000010 + +#endif /* CONFIG_CMD_NET */ + +/* Support for relocation */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 +#define CONFIG_SYS_INIT_RAM_SIZE 0x800 +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ + CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) + +/* ----------------------------------------------------------------------------- + * Board specific + * ----------------------------------------------------------------------------- + */ +#define CONFIG_SYS_NO_FLASH + +/* Uncomment to define the board revision statically */ +/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */ + +#define CONFIG_SYS_CACHELINE_SIZE 64 + +/* Defines for SPL */ +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x40200800 +#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ + +#define CONFIG_SPL_BSS_START_ADDR 0x80000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +/* + * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM + * 64 bytes before this address should be set aside for u-boot.img's + * header. That is 0x800FFFC0--0x80100000 should not be used for any + * other needs. + */ +#define CONFIG_SYS_TEXT_BASE 0x80100000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 /* ----------------------------------------------------------------------------- * Default environment diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h deleted file mode 100644 index 01336ff..0000000 --- a/include/configs/omap3_evm_common.h +++ /dev/null @@ -1,286 +0,0 @@ -/* - * Common configuration settings for the TI OMAP3 EVM board. - * - * Copyright (C) 2006-2011 Texas Instruments Incorporated - http://www.ti.com/ - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __OMAP3_EVM_COMMON_H -#define __OMAP3_EVM_COMMON_H - -/* - * High level configuration options - */ -#define CONFIG_OMAP /* This is TI OMAP core */ -#define CONFIG_OMAP_GPIO -#define CONFIG_OMAP_COMMON -/* Common ARM Erratas */ -#define CONFIG_ARM_ERRATA_454179 -#define CONFIG_ARM_ERRATA_430973 -#define CONFIG_ARM_ERRATA_621766 - -#define CONFIG_SDRC /* The chip has SDRC controller */ - -#define CONFIG_OMAP3_EVM /* This is a OMAP3 EVM */ -#define CONFIG_TWL4030_POWER /* with TWL4030 PMIC */ - -/* - * Clock related definitions - */ -#define V_OSCK 26000000 /* Clock output from T2 */ -#define V_SCLK (V_OSCK >> 1) - -/* - * OMAP3 has 12 GP timers, they can be driven by the system clock - * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). - * This rate is divided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2 -#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ - -/* Size of environment - 128KB */ -#define CONFIG_ENV_SIZE (128 << 10) - -/* Size of malloc pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) - -/* - * Physical Memory Map - * Note 1: CS1 may or may not be populated - * Note 2: SDRAM size is expected to be at least 32MB - */ -#define CONFIG_NR_DRAM_BANKS 2 -#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 -#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 - -/* Limits for memtest */ -#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) -#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ - 0x01F00000) /* 31MB */ - -/* Default load address */ -#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) - -/* ----------------------------------------------------------------------------- - * Hardware drivers - * ----------------------------------------------------------------------------- - */ - -/* - * NS16550 Configuration - */ -#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ - -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK - -/* - * select serial console configuration - */ -#define CONFIG_CONS_INDEX 1 -#define CONFIG_SERIAL1 1 /* UART1 on OMAP3 EVM */ -#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ - 115200} - -/* - * I2C - */ -#define CONFIG_SYS_I2C -#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 -#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 -#define CONFIG_SYS_I2C_OMAP34XX - -/* - * PISMO support - */ -/* Monitor at start of flash - Reserve 2 sectors */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) - -/* Start location & size of environment */ -#define ONENAND_ENV_OFFSET 0x260000 -#define SMNAND_ENV_OFFSET 0x260000 - -#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ - -/* - * NAND - */ -/* Physical address to access NAND */ -#define CONFIG_SYS_NAND_ADDR NAND_BASE - -/* Physical address to access NAND at CS0 */ -#define CONFIG_SYS_NAND_BASE NAND_BASE - -/* Max number of NAND devices */ -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BUSWIDTH_16BIT -/* Timeout values (in ticks) */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ) -#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ) - -/* Flash banks JFFS2 should use */ -#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \ - CONFIG_SYS_MAX_NAND_DEVICE) - -#define CONFIG_SYS_JFFS2_MEM_NAND -#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS -#define CONFIG_SYS_JFFS2_NUM_BANKS 1 - -#define CONFIG_JFFS2_NAND -/* nand device jffs2 lives on */ -#define CONFIG_JFFS2_DEV "nand0" -/* Start of jffs2 partition */ -#define CONFIG_JFFS2_PART_OFFSET 0x680000 -/* Size of jffs2 partition */ -#define CONFIG_JFFS2_PART_SIZE 0xf980000 - -/* - * USB - */ -#ifdef CONFIG_USB_OMAP3 - -#ifdef CONFIG_USB_MUSB_HCD - -#define CONFIG_USB_STORAGE -#define CONGIG_CMD_STORAGE - -#ifdef CONFIG_USB_KEYBOARD -#define CONFIG_SYS_USB_EVENT_POLL -#define CONFIG_PREBOOT "usb start" -#endif /* CONFIG_USB_KEYBOARD */ - -#endif /* CONFIG_USB_MUSB_HCD */ - -#ifdef CONFIG_USB_MUSB_UDC -/* USB device configuration */ -#define CONFIG_USB_DEVICE -#define CONFIG_USB_TTY -#define CONFIG_SYS_CONSOLE_IS_IN_ENV - -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "EVM" -#endif /* CONFIG_USB_MUSB_UDC */ - -#endif /* CONFIG_USB_OMAP3 */ - -/* ---------------------------------------------------------------------------- - * U-Boot features - * ---------------------------------------------------------------------------- - */ -#define CONFIG_SYS_MAXARGS 16 /* max args for a command */ - -#define CONFIG_MISC_INIT_R - -#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG - -/* Size of Console IO buffer */ -#define CONFIG_SYS_CBSIZE 512 - -/* Size of print buffer */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ - sizeof(CONFIG_SYS_PROMPT) + 16) - -/* Size of bootarg buffer */ -#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) - -#define CONFIG_BOOTFILE "uImage" - -/* - * NAND / OneNAND - */ -#if defined(CONFIG_CMD_NAND) -#define CONFIG_SYS_FLASH_BASE NAND_BASE - -#define CONFIG_NAND_OMAP_GPMC -#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET -#elif defined(CONFIG_CMD_ONENAND) -#define CONFIG_SYS_FLASH_BASE ONENAND_MAP -#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP -#endif - -#if !defined(CONFIG_ENV_IS_NOWHERE) -#if defined(CONFIG_CMD_NAND) -#define CONFIG_ENV_IS_IN_NAND -#elif defined(CONFIG_CMD_ONENAND) -#define CONFIG_ENV_IS_IN_ONENAND -#define CONFIG_ENV_OFFSET ONENAND_ENV_OFFSET -#endif -#endif /* CONFIG_ENV_IS_NOWHERE */ - -#define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET - -#if defined(CONFIG_CMD_NET) - -/* Ethernet (SMSC9115 from SMSC9118 family) */ -#define CONFIG_SMC911X -#define CONFIG_SMC911X_32_BIT -#define CONFIG_SMC911X_BASE 0x2C000000 - -/* BOOTP fields */ -#define CONFIG_BOOTP_SUBNETMASK 0x00000001 -#define CONFIG_BOOTP_GATEWAY 0x00000002 -#define CONFIG_BOOTP_HOSTNAME 0x00000004 -#define CONFIG_BOOTP_BOOTPATH 0x00000010 - -#endif /* CONFIG_CMD_NET */ - -/* Support for relocation */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 -#define CONFIG_SYS_INIT_RAM_SIZE 0x800 -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) - -/* ----------------------------------------------------------------------------- - * Board specific - * ----------------------------------------------------------------------------- - */ -#define CONFIG_SYS_NO_FLASH - -/* Uncomment to define the board revision statically */ -/* #define CONFIG_STATIC_BOARD_REV OMAP3EVM_BOARD_GEN_2 */ - -#define CONFIG_SYS_CACHELINE_SIZE 64 - -/* Defines for SPL */ -#define CONFIG_SPL_FRAMEWORK -#define CONFIG_SPL_TEXT_BASE 0x40200800 -#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ - -#define CONFIG_SPL_BSS_START_ADDR 0x80000000 -#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ - -#define CONFIG_SPL_BOARD_INIT -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBDISK_SUPPORT -#define CONFIG_SPL_I2C_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_SERIAL_SUPPORT -#define CONFIG_SPL_POWER_SUPPORT -#define CONFIG_SPL_OMAP3_ID_NAND -#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" - -/* - * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM - * 64 bytes before this address should be set aside for u-boot.img's - * header. That is 0x800FFFC0--0x80100000 should not be used for any - * other needs. - */ -#define CONFIG_SYS_TEXT_BASE 0x80100000 -#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 -#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 - -#endif /* __OMAP3_EVM_COMMON_H */ diff --git a/include/configs/omap3_evm_quick_mmc.h b/include/configs/omap3_evm_quick_mmc.h deleted file mode 100644 index b7d8765..0000000 --- a/include/configs/omap3_evm_quick_mmc.h +++ /dev/null @@ -1,89 +0,0 @@ -/* - * Configuration settings for quick boot from MMC on OMAP3 EVM. - * - * Copyright (C) 2006-2010 Texas Instruments Incorporated - http://www.ti.com/ - * - * Author : - * Sanjeev Premi <premi@ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __OMAP3_EVM_QUICK_MMC_H -#define __OMAP3_EVM_QUICK_MMC_H - -#include <asm/arch/cpu.h> -#include <asm/arch/omap.h> - -/* ---------------------------------------------------------------------------- - * Supported U-Boot commands - * ---------------------------------------------------------------------------- - */ - -/* - * Board revision is detected by probing the Ethernet chip. - * - * When revision is statically configured via CONFIG_STATIC_BOARD_REV, - * this option can be removed. Generated binary is leaner by ~16Kbytes. - */ - -/* ---------------------------------------------------------------------------- - * Supported U-Boot features - * ---------------------------------------------------------------------------- - */ -#define CONFIG_SILENT_CONSOLE -#define CONFIG_ENV_IS_NOWHERE - -/* ---------------------------------------------------------------------------- - * Supported hardware - * ---------------------------------------------------------------------------- - */ - -/* MMC */ -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_OMAP_HSMMC -#define CONFIG_DOS_PARTITION - -/* ----------------------------------------------------------------------------- - * Include common board configuration - * ----------------------------------------------------------------------------- - */ -#include "omap3_evm_common.h" - -/* ----------------------------------------------------------------------------- - * Default environment - * ----------------------------------------------------------------------------- - */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "verify=no\0" \ - "silent=1" - -#define CONFIG_BOOTCOMMAND \ - "mmc rescan 0; " \ - "fatload mmc 0 0x82000000 uImage; " \ - "bootm 0x82000000;" - -/* - * Update the bootargs as necessary e.g. size of memory, partition and fstype - */ -#define CONFIG_BOOTARGS \ - "quiet " \ - "console=ttyO0,115200n8 " \ - "mem=128M " \ - "noinitrd " \ - "root=/dev/mmcblk0p2 rw " \ - "rootfstype=ext3 rootwait" - -/* - * SPL - */ -#define CONFIG_SPL_MMC_SUPPORT -#define CONFIG_SPL_FAT_SUPPORT -#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ -#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ -#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 -#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" - -#endif /* __OMAP3_EVM_QUICK_MMC_H */ diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h deleted file mode 100644 index da5d325..0000000 --- a/include/configs/omap3_evm_quick_nand.h +++ /dev/null @@ -1,91 +0,0 @@ -/* - * Configuration settings for quick boot from NAND on OMAP3 EVM. - * - * Copyright (C) 2006-2010 Texas Instruments Incorporated - http://www.ti.com/ - * - * Author : - * Sanjeev Premi <premi@ti.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __OMAP3_EVM_QUICK_NAND_H -#define __OMAP3_EVM_QUICK_NAND_H - -#include <asm/arch/cpu.h> -#include <asm/arch/omap.h> - -/* ---------------------------------------------------------------------------- - * Supported U-Boot commands - * ---------------------------------------------------------------------------- - */ -#define CONFIG_CMD_NAND - -/* - * Board revision is detected by probing the Ethernet chip. - * - * When revision is statically configured via CONFIG_STATIC_BOARD_REV, - * this option can be removed. Generated binary is leaner by ~16Kbytes. - */ - -/* ---------------------------------------------------------------------------- - * Supported U-Boot features - * ---------------------------------------------------------------------------- - */ -#define CONFIG_SILENT_CONSOLE -#define CONFIG_ENV_IS_NOWHERE - -/* ----------------------------------------------------------------------------- - * Include common board configuration - * ----------------------------------------------------------------------------- - */ -#include "omap3_evm_common.h" - -/* ----------------------------------------------------------------------------- - * Default environment - * ----------------------------------------------------------------------------- - */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "verify=no\0" \ - "silent=1" - -#define CONFIG_BOOTCOMMAND \ - "nandecc hw; " \ - "nand read.i 0x80000000 280000 300000; " \ - "bootm 0x80000000;" - -/* - * Update the bootargs as necessary e.g. size of memory, partition and fstype - */ -#define CONFIG_BOOTARGS \ - "quiet " \ - "console=ttyO0,115200n8 " \ - "mem=128M " \ - "noinitrd " \ - "root=/dev/mtdblock4 rw " \ - "rootfstype=jffs2 " - -/* - * SPL - */ -#define CONFIG_SPL_NAND_SIMPLE -#define CONFIG_SPL_NAND_SUPPORT -#define CONFIG_SPL_NAND_BASE -#define CONFIG_SPL_NAND_DRIVERS -#define CONFIG_SPL_NAND_ECC -#define CONFIG_SYS_NAND_5_ADDR_CYCLE -#define CONFIG_SYS_NAND_PAGE_COUNT 64 -#define CONFIG_SYS_NAND_PAGE_SIZE 2048 -#define CONFIG_SYS_NAND_OOBSIZE 64 -#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) -#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0 -#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\ - 10, 11, 12, 13} -#define CONFIG_SYS_NAND_ECCSIZE 512 -#define CONFIG_SYS_NAND_ECCBYTES 3 -#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW -#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 - -#endif /* __OMAP3_EVM_QUICK_NAND_H */ |