summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/ap325rxa.h1
-rw-r--r--include/configs/edminiv2.h34
-rw-r--r--include/configs/ms7720se.h1
-rw-r--r--include/configs/omap4_panda.h26
-rw-r--r--include/configs/omap4_sdp4430.h26
-rw-r--r--include/configs/openrd_base.h31
-rw-r--r--include/configs/r2dplus.h1
-rw-r--r--include/configs/r7780mp.h1
-rw-r--r--include/configs/s5p_goni.h6
9 files changed, 122 insertions, 5 deletions
diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h
index 70dd47e..80a5797 100644
--- a/include/configs/ap325rxa.h
+++ b/include/configs/ap325rxa.h
@@ -138,6 +138,7 @@
#define CONFIG_SYS_ATA_DATA_OFFSET 0x200 /* data reg offset */
#define CONFIG_SYS_ATA_REG_OFFSET 0x200 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x210 /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
/* if you use all NOR Flash , you change dip-switch. Please see Manual. */
#define CONFIG_SYS_MAX_FLASH_BANKS 1
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 055931c..57dd165 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -60,7 +60,7 @@
#define ORION5X_MPP0_7 0x00000003
#define ORION5X_MPP8_15 0x55550000
-#define ORION5X_MPP16_23 0x00000000
+#define ORION5X_MPP16_23 0x00005555
/*
* Board-specific values for Orion5x GPIO low level init:
@@ -131,6 +131,7 @@
* Commands configuration - using default command set for now
*/
#include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
/*
* Network
@@ -150,6 +151,37 @@
#endif
/*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE 4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
* Environment variables configurations
*/
#define CONFIG_ENV_IS_IN_FLASH 1
diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h
index ba0a3f8..0ea3527 100644
--- a/include/configs/ms7720se.h
+++ b/include/configs/ms7720se.h
@@ -122,5 +122,6 @@
#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* data reg offset */
#define CONFIG_SYS_ATA_REG_OFFSET 0 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x200 /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
#endif /* __MS7720SE_H */
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index b1e40a3..a0d27a4 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -35,6 +35,7 @@
#define CONFIG_OMAP44XX 1 /* which is a 44XX */
#define CONFIG_OMAP4430 1 /* which is in a 4430 */
#define CONFIG_PANDA 1 /* working with Panda */
+#define CONFIG_ARCH_CPU_INIT
/* Get CPU defs */
#include <asm/arch/cpu.h>
@@ -102,12 +103,29 @@
#define CONFIG_DRIVER_OMAP34XX_I2C 1
#define CONFIG_I2C_MULTI_BUS 1
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER 1
+
/* MMC */
#define CONFIG_MMC 1
#define CONFIG_OMAP3_MMC 1
#define CONFIG_SYS_MMC_SET_DEV 1
#define CONFIG_DOS_PARTITION 1
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "OMAP4 Panda"
+
/* Flash */
#define CONFIG_SYS_NO_FLASH 1
@@ -135,16 +153,21 @@
* Environment setup
*/
+#define CONFIG_BOOTDELAY 3
+
/* allow overwriting serial config and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
+ "usbtty=cdc_acm\0" \
+ "vram=16M\0" \
"mmcdev=1\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"mmcargs=setenv bootargs console=${console} " \
+ "vram=${vram} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -162,7 +185,6 @@
"else " \
"if run loaduimage; then " \
"run mmcboot; " \
- "else run nandboot; " \
"fi; " \
"fi; " \
"fi"
@@ -195,7 +217,7 @@
#define CONFIG_SYS_LOAD_ADDR 0x80000000
/* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE GPT1_BASE
+#define CONFIG_SYS_TIMERBASE GPT2_BASE
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h
index 8121554..d5439f9 100644
--- a/include/configs/omap4_sdp4430.h
+++ b/include/configs/omap4_sdp4430.h
@@ -36,6 +36,7 @@
#define CONFIG_OMAP44XX 1 /* which is a 44XX */
#define CONFIG_OMAP4430 1 /* which is in a 4430 */
#define CONFIG_4430SDP 1 /* working with SDP */
+#define CONFIG_ARCH_CPU_INIT
/* Get CPU defs */
#include <asm/arch/cpu.h>
@@ -103,12 +104,29 @@
#define CONFIG_DRIVER_OMAP34XX_I2C 1
#define CONFIG_I2C_MULTI_BUS 1
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER 1
+
/* MMC */
#define CONFIG_MMC 1
#define CONFIG_OMAP3_MMC 1
#define CONFIG_SYS_MMC_SET_DEV 1
#define CONFIG_DOS_PARTITION 1
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "SDP4430"
+
/* Flash */
#define CONFIG_SYS_NO_FLASH 1
@@ -136,16 +154,21 @@
* Environment setup
*/
+#define CONFIG_BOOTDELAY 3
+
/* allow overwriting serial config and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"console=ttyS2,115200n8\0" \
+ "usbtty=cdc_acm\0" \
+ "vram=16M\0" \
"mmcdev=1\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"mmcargs=setenv bootargs console=${console} " \
+ "vram=${vram} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -163,7 +186,6 @@
"else " \
"if run loaduimage; then " \
"run mmcboot; " \
- "else run nandboot; " \
"fi; " \
"fi; " \
"fi"
@@ -196,7 +218,7 @@
#define CONFIG_SYS_LOAD_ADDR 0x80000000
/* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE GPT1_BASE
+#define CONFIG_SYS_TIMERBASE GPT2_BASE
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
#define CONFIG_SYS_HZ 1000
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
index 52fa73d..846dfcd 100644
--- a/include/configs/openrd_base.h
+++ b/include/configs/openrd_base.h
@@ -103,6 +103,7 @@
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PING
#define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
/*
* NAND configuration
@@ -205,6 +206,36 @@
#endif /* CONFIG_CMD_USB */
/*
+ * IDe Support on SATA port0
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE 4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS 2
+#define CONFIG_SYS_IDE_MAXDEVICE 2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR KW_SATA_BASE
+/* ATA bus 0 is Kirkwood port 0 on openrd */
+#define CONFIG_SYS_ATA_IDE0_OFFSET KW_SATA_PORT0_OFFSET
+/* ATA bus 1 is Kirkwood port 1 on openrd */
+#define CONFIG_SYS_ATA_IDE1_OFFSET KW_SATA_PORT1_OFFSET
+#endif /* CONFIG_CMD_IDE */
+
+/*
* File system
*/
#define CONFIG_CMD_FAT
diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h
index 8931b97..955f3ff 100644
--- a/include/configs/r2dplus.h
+++ b/include/configs/r2dplus.h
@@ -96,6 +96,7 @@
#define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */
#define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
/*
* SuperH PCI Bridge Configration
diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h
index 71c570e..3afe93a 100644
--- a/include/configs/r7780mp.h
+++ b/include/configs/r7780mp.h
@@ -171,6 +171,7 @@
#define CONFIG_SYS_ATA_DATA_OFFSET 0x1000 /* data reg offset */
#define CONFIG_SYS_ATA_REG_OFFSET 0x1000 /* reg offset */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x800 /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
#endif /* CONFIG_CMD_IDE */
#endif /* __R7780RP_H */
diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h
index ff0dbd3..c8ea8fd 100644
--- a/include/configs/s5p_goni.h
+++ b/include/configs/s5p_goni.h
@@ -67,6 +67,11 @@
#define CONFIG_SERIAL_MULTI 1
#define CONFIG_BAUDRATE 115200
+/* MMC */
+#define CONFIG_GENERIC_MMC 1
+#define CONFIG_MMC 1
+#define CONFIG_S5P_MMC 1
+
/* It should define before config_cmd_default.h */
#define CONFIG_SYS_NO_FLASH 1
@@ -82,6 +87,7 @@
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_ONENAND
#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_MMC
#define CONFIG_BOOTDELAY 1
#define CONFIG_ZERO_BOOTDELAY_CHECK