summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/MPC8544DS.h52
-rw-r--r--include/configs/MPC8560ADS.h38
-rw-r--r--include/configs/sbc8560.h128
3 files changed, 136 insertions, 82 deletions
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 669f4d7c..091fd2e 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -148,8 +148,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
*/
#define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */
-#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
-
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
#define CFG_BR0_PRELIM 0xff801001
@@ -158,10 +156,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#define CFG_OR0_PRELIM 0xff806e65
#define CFG_OR1_PRELIM 0xff806e65
-#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE}
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
#define CFG_FLASH_QUIET_TEST
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
@@ -203,30 +201,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM 1
-#define CFG_INIT_L1_LOCK 1
-#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */
-#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */
-
-/* define to use L2SRAM as initial stack */
-#undef CONFIG_L2_INIT_RAM
-#define CFG_INIT_L2_ADDR 0xf8fc0000
-#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */
-
-#ifdef CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR
-#define CFG_INIT_RAM_END CFG_INIT_L1_END
-#else
-#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR
-#define CFG_INIT_RAM_END CFG_INIT_L2_END
-#endif
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */
+#define CFG_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port - controlled on board with jumper J8
* open - index 2
@@ -314,6 +300,26 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#if defined(CONFIG_PCI)
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CFG_PCIE2_IO_PHYS
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
@@ -382,7 +388,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
#if CFG_MONITOR_BASE > 0xfff80000
#define CFG_ENV_ADDR 0xfff80000
#else
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000)
#endif
#define CFG_ENV_SIZE 0x2000
#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index edf8525..27212162 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -538,29 +538,29 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyCPM\0" \
- "ramdiskaddr=1000000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0" \
- "fdtaddr=400000\0" \
- "fdtfile=mpc8560ads.dtb\0"
+ "netdev=eth0\0" \
+ "consoledev=ttyCPM\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8560ads.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 146eafe..6345cce 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -24,8 +24,8 @@
* MA 02111-1307 USA
*/
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
+/* sbc8560 board configuration file */
+/* please refer to doc/README.sbc8560 for more info */
/* make sure you change the MAC address and other network params first,
* search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
*/
@@ -102,11 +102,11 @@
#define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
#define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#if defined(CONFIG_MPC85xx_REV1)
- #define CONFIG_DDR_DLL /* possible DLL fix needed */
+ #define CONFIG_DDR_DLL /* possible DLL fix needed */
#endif
#undef CONFIG_CLOCKS_IN_MHZ
@@ -177,8 +177,8 @@
#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
+#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
@@ -200,6 +200,11 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
/*
* I2C
*/
@@ -215,16 +220,28 @@
#define CFG_PCI_MEM_PHYS 0xC0000000
#define CFG_PCI_MEM_SIZE 0x10000000
-#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
+#ifdef CONFIG_TSEC_ENET
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
-# define CONFIG_NET_MULTI 1
-# define CONFIG_MII 1 /* MII PHY management */
-# define CONFIG_MPC85xx_TSEC1
-# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0"
-# define TSEC1_PHY_ADDR 25
-# define TSEC1_PHYIDX 0
-/* Options are: TSEC0 */
-# define CONFIG_ETHPRIME "TSEC0"
+#ifndef CONFIG_MII
+#define CONFIG_MII 1 /* MII PHY management */
+#endif
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 0x19
+#define TSEC2_PHY_ADDR 0x1a
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
@@ -272,20 +289,20 @@
* FLASH and environment organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
-#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
+#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#if 0
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION /* use hardware protection */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CFG_FLASH_PROTECTION /* use hardware protection */
#endif
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if 0
/* XXX This doesn't work and I don't want to fix it */
@@ -315,9 +332,8 @@
#define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600"
+#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600"
/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000"
#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
@@ -389,25 +405,57 @@
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#if defined(CONFIG_CMD_KGDB)
- #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
- #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*Note: change below for your network setting!!! */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-# define CONFIG_ETHADDR 00:01:af:07:9b:8a
-# define CONFIG_HAS_ETH1
-# define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-# define CONFIG_HAS_ETH2
-# define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_HAS_ETH0
+#define CONFIG_HAS_ETH1
#endif
-#define CONFIG_SERVERIP 192.168.0.131
-#define CONFIG_IPADDR 192.168.0.105
-#define CONFIG_GATEWAYIP 0.0.0.0
-#define CONFIG_NETMASK 255.255.255.0
+/* You can compile in a MAC address and your custom net settings by using
+ * the following syntax. Your board should be marked with the assigned
+ * MAC addresses directly on it.
+ *
+ * #define CONFIG_ETHADDR de:ad:be:ef:00:00
+ * #define CONFIG_ETH1ADDR fa:ke:ad:dr:es:s!
+ * #define CONFIG_SERVERIP <server ip>
+ * #define CONFIG_IPADDR <board ip>
+ * #define CONFIG_GATEWAYIP <gateway ip>
+ * #define CONFIG_NETMASK <your netmask>
+ */
+
#define CONFIG_HOSTNAME SBC8560
#define CONFIG_ROOTPATH /home/ppc
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=ramdisk.uboot\0" \
+ "fdtaddr=c00000\0" \
+ "fdtfile=sbc8560.dtb\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */