diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/TQM5200.h | 31 | ||||
| -rw-r--r-- | include/configs/TQM85xx.h | 7 | ||||
| -rw-r--r-- | include/configs/cmc_pu2.h | 11 | ||||
| -rw-r--r-- | include/configs/gth2.h | 195 | ||||
| -rw-r--r-- | include/configs/ppmc7xx.h | 419 | ||||
| -rw-r--r-- | include/configs/spieval.h | 28 | ||||
| -rw-r--r-- | include/configs/trab.h | 6 | ||||
| -rw-r--r-- | include/configs/voiceblue.h | 56 |
8 files changed, 663 insertions, 90 deletions
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index 6020998..6b8759f 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -37,7 +37,6 @@ #define CONFIG_TQM5200 1 /* ... on TQM5200 module */ #undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ #define CONFIG_STK52XX 1 /* ... on a STK52XX base board */ -#define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */ #define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ @@ -83,7 +82,7 @@ #define CONFIG_PCI_IO_SIZE 0x01000000 #define CONFIG_NET_MULTI 1 -#define CONFIG_EEPRO100 +#define CONFIG_EEPRO100 1 #define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 #endif /* CONFIG_STK52XX */ @@ -192,16 +191,6 @@ #undef CONFIG_BOOTARGS -#if defined (CONFIG_TQM5200_AA) -# define CONFIG_U_BOOT_SUFFIX "-AA\0" -#elif defined (CONFIG_TQM5200_AB) -# define CONFIG_U_BOOT_SUFFIX "-AB\0" -#elif defined (CONFIG_TQM5200_AC) -# define CONFIG_U_BOOT_SUFFIX "-AC\0" -#else -# define CONFIG_U_BOOT_SUFFIX "\0" -#endif - #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ @@ -218,7 +207,7 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "bootfile=/tftpboot/tqm5200/uImage\0" \ "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin" CONFIG_U_BOOT_SUFFIX \ + "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ "update=protect off FC000000 FC05FFFF;" \ "erase FC000000 FC05FFFF;" \ "cp.b 200000 FC000000 ${filesize};" \ @@ -284,13 +273,6 @@ #endif /* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB) -#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \ - CFG_I2C_SLAVE } -#elif defined (CONFIG_TQM5200_AC) -#define I2C_ADDR_LIST { CFG_I2C_SLAVE } -#endif - #if defined (CONFIG_MINIFAP) #undef I2C_ADDR_LIST #define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \ @@ -493,13 +475,9 @@ * SRAM - Do not map below 2 GB in address space, because this area is used * for SDRAM autosizing. */ -#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF) +#if defined (CONFIG_CS_AUTOCONF) #define CFG_CS2_START 0xE5000000 -#ifdef CONFIG_TQM5200_AB -#define CFG_CS2_SIZE 0x80000 /* 512 kByte */ -#else /* CONFIG_CS_AUTOCONF */ #define CFG_CS2_SIZE 0x100000 /* 1 MByte */ -#endif #define CFG_CS2_CFG 0x0004D930 #endif @@ -507,8 +485,7 @@ * Grafic controller - Do not map below 2 GB in address space, because this * area is used for SDRAM autosizing. */ -#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \ - defined (CONFIG_CS_AUTOCONF) +#if defined (CONFIG_CS_AUTOCONF) #define SM501_FB_BASE 0xE0000000 #define CFG_CS1_START (SM501_FB_BASE) #define CFG_CS1_SIZE 0x4000000 /* 64 MByte */ diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index 18197f2..da6946b 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -177,6 +177,13 @@ #define CFG_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} +/* PS/2 Keyboard */ +#define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ +#define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ +#define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ +#define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */ +#define CONFIG_BOARD_EARLY_INIT_R 1 + /* Use the HUSH parser */ #define CFG_HUSH_PARSER #ifdef CFG_HUSH_PARSER diff --git a/include/configs/cmc_pu2.h b/include/configs/cmc_pu2.h index 46280f7..572a70f 100644 --- a/include/configs/cmc_pu2.h +++ b/include/configs/cmc_pu2.h @@ -108,7 +108,7 @@ /* still about 20 kB free with this defined */ #define CFG_LONGHELP -#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTDELAY 1 #ifdef CONFIG_HARD_I2C #define CONFIG_COMMANDS \ @@ -206,15 +206,6 @@ struct bd_info_ext { #error CONFIG_USE_IRQ not supported #endif -#define CFG_DEVICE_NULLDEV 1 /* enble null device */ -#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */ - -#define CONFIG_AUTOBOOT_KEYED -#define CONFIG_AUTOBOOT_PROMPT "autoboot in %d seconds\n" -#define CONFIG_AUTOBOOT_STOP_STR "R" /* default password */ - -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - #define CONFIG_EXTRA_ENV_SETTINGS \ "net_nfs=tftp ${loadaddr} ${bootfile};run nfsargs addip addcons " \ "addmtd;bootm\0" \ diff --git a/include/configs/gth2.h b/include/configs/gth2.h new file mode 100644 index 0000000..77d2d56 --- /dev/null +++ b/include/configs/gth2.h @@ -0,0 +1,195 @@ +/* + * (C) Copyright 2005 + * Thomas.Lange@corelatus.se + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * This file contains the configuration parameters for the gth2 board. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MIPS32 1 /* MIPS32 CPU core */ +#define CONFIG_GTH2 1 +#define CONFIG_AU1X00 1 /* alchemy series cpu */ + +#define CONFIG_AU1000 1 + +#define CONFIG_MISC_INIT_R 1 + +#define CONFIG_ETHADDR DE:AD:BE:EF:01:02 /* Ethernet address */ + +#define CONFIG_BOOTDELAY 1 /* autoboot after 1 seconds */ + +#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */ + +#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */ + +#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */ + +#define CONFIG_BAUDRATE 115200 + +/* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 115200 } + +/* Only interrupt boot if space is pressed */ +/* If a long serial cable is connected but */ +/* other end is dead, garbage will be read */ +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT "Press space to abort autoboot in %d second\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +#define CONFIG_TIMESTAMP /* Print image info with timestamp */ +#define CONFIG_BOOTARGS "panic=1" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "addmisc=setenv bootargs $(bootargs) " \ + "ethaddr=$(ethaddr) \0" \ + "netboot=bootp;run addmisc;bootm\0" \ + "" + +/* Boot from Compact flash partition 2 as default */ +#define CONFIG_BOOTCOMMAND "ide reset;disk 0x81000000 0:2;run addmisc;bootm" + +#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_IDE | CFG_CMD_DHCP ) & \ + ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | \ + CFG_CMD_MII | CFG_CMD_LOADS | CFG_CMD_LOADB | CFG_CMD_ELF | \ + CFG_CMD_BDI | CFG_CMD_BEDBUG | CFG_CMD_NFS | CFG_CMD_AUTOSCRIPT )) + +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "GTH2 # " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args*/ + +#define CFG_MALLOC_LEN 128*1024 + +#define CFG_BOOTPARAMS_LEN 128*1024 + +#define CFG_MHZ 500 + +#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */ + +#define CFG_SDRAM_BASE 0x80000000 /* Cached addr */ + +#define CFG_LOAD_ADDR 0x81000000 /* default load address */ + +#define CFG_MEMTEST_START 0x80100000 +#define CFG_MEMTEST_END 0x83000000 + +#define CONFIG_HW_WATCHDOG 1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ + +#define PHYS_FLASH 0xbfc00000 /* Flash Bank #1 */ + +/* The following #defines are needed to get flash environment right */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MONITOR_LEN (192 << 10) + +#define CFG_INIT_SP_OFFSET 0x400000 + +/* We boot from this flash, selected with dip switch */ +#define CFG_FLASH_BASE PHYS_FLASH + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (2 * CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (2 * CFG_HZ) /* Timeout for Flash Write */ + +#define CFG_ENV_IS_NOWHERE 1 + +/* Address and size of Primary Environment Sector */ +#define CFG_ENV_ADDR 0xB0030000 +#define CFG_ENV_SIZE 0x10000 + +#define CONFIG_FLASH_16BIT + +#define CONFIG_NR_DRAM_BANKS 2 + +#define CONFIG_NET_MULTI + +#define CONFIG_MEMSIZE_IN_BYTES + +/*---ATA PCMCIA ------------------------------------*/ +#define CFG_PCMCIA_MEM_SIZE 0x4000000 /* Offset to slot 1 FIXME!!! */ + +#define CFG_PCMCIA_MEM_ADDR 0x20000000 +#define CFG_PCMCIA_IO_BASE 0x28000000 +#define CFG_PCMCIA_ATTR_BASE 0x30000000 + +#define CONFIG_PCMCIA_SLOT_A + +#define CONFIG_ATAPI 1 +#define CONFIG_MAC_PARTITION 1 + +/* We run CF in "true ide" mode or a harddrive via pcmcia */ +#define CONFIG_IDE_PCMCIA 1 + +/* We only support one slot for now */ +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_ATA_IDE0_OFFSET 0 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_IO_BASE + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET 0 + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET 0 + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0200 + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 16384 +#define CFG_ICACHE_SIZE 16384 +#define CFG_CACHELINE_SIZE 32 + +#define GPIO_CACONFIG (1<<0) +#define GPIO_DPACONFIG (1<<6) +#define GPIO_ERESET (1<<11) +#define GPIO_EEDQ (1<<17) +#define GPIO_WDI (1<<18) +#define GPIO_RJ1LY (1<<22) +#define GPIO_RJ1LG (1<<23) +#define GPIO_LEDCLK (1<<29) +#define GPIO_LEDD (1<<30) +#define GPIO_CPU_LED (1<<31) + +#endif /* __CONFIG_H */ diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h new file mode 100644 index 0000000..ea15524 --- /dev/null +++ b/include/configs/ppmc7xx.h @@ -0,0 +1,419 @@ +/* + * ppmc7xx.h + * --------- + * + * Wind River PPMC 7xx/74xx board configuration file. + * + * By Richard Danter (richard.danter@windriver.com) + * Copyright (C) 2005 Wind River Systems + */ + + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_PPMC7XX + + +/*=================================================================== + * + * User configurable settings - Modify to your preference + * + *=================================================================== + */ + +/* + * Debug + * + * DEBUG - Define this is you want extra debug info + * GTREGREAD - Required to build with debug + * do_bdinfo - Required to build with debug + */ + +#undef DEBUG +#define GTREGREAD(x) 0xFFFFFFFF +#define do_bdinfo(a,b,c,d) + + +/* + * CPU type + * + * CONFIG_7xx - We have a 750 or 755 CPU + * CONFIG_74xx - We have a 7400 CPU + * CONFIG_ALTIVEC - We have altivec enabled CPU (only 7400) + * CONFIG_BUS_CLK - System bus clock in Hz + */ + +#define CONFIG_7xx +#undef CONFIG_74xx +#undef CONFIG_ALTIVEC +#define CONFIG_BUS_CLK 66000000 + + +/* + * Monitor configuration + * + * CONFIG_COMMANDS - List of command sets to include in shell + * + * The following command sets have been tested and known to work: + * + * CFG_CMD_CACHE - Cache control commands + * CFG_CMD_MEMORY - Memory display, change and test commands + * CFG_CMD_FLASH - Erase and program flash + * CFG_CMD_ENV - Environment commands + * CFG_CMD_RUN - Run commands stored in env vars + * CFG_CMD_ELF - Load ELF files + * CFG_CMD_NET - Networking/file download commands + * CFG_CMD_PING - ICMP Echo Request command + * CFG_CMD_PCI - PCI Bus scanning command + */ + +#define CONFIG_COMMANDS ( (CFG_CMD_DFL & ~(CFG_CMD_KGDB)) | \ + CFG_CMD_FLASH | \ + CFG_CMD_ENV | \ + CFG_CMD_RUN | \ + CFG_CMD_ELF | \ + CFG_CMD_NET | \ + CFG_CMD_PING | \ + CFG_CMD_PCI) + + +/* + * Serial configuration + * + * CONFIG_CONS_INDEX - Serial console port number (COM1) + * CONFIG_BAUDRATE - Serial speed + */ + +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 9600 + + +/* + * PCI config + * + * CONFIG_PCI - Enable PCI bus + * CONFIG_PCI_PNP - Enable Plug & Play support + * CONFIG_PCI_SCAN_SHOW - Enable display of devices at startup + */ + +#define CONFIG_PCI +#define CONFIG_PCI_PNP +#undef CONFIG_PCI_SCAN_SHOW + + +/* + * Network config + * + * CONFIG_NET_MULTI - Support for multiple network interfaces + * CONFIG_EEPRO100 - Intel 8255x Ethernet Controller + * CONFIG_EEPRO100_SROM_WRITE - Enable writing to network card ROM + */ + +#define CONFIG_NET_MULTI +#define CONFIG_EEPRO100 +#define CONFIG_EEPRO100_SROM_WRITE + + +/* + * Enable extra init functions + * + * CONFIG_MISC_INIT_F - Call pre-relocation init functions + * CONFIG_MISC_INIT_R - Call post relocation init functions + */ + +#undef CONFIG_MISC_INIT_F +#define CONFIG_MISC_INIT_R + + +/* + * Boot config + * + * CONFIG_BOOTCOMMAND - Command(s) to execute to auto-boot + * CONFIG_BOOTDELAY - How long to wait before auto-boot (in sec) + */ + +#define CONFIG_BOOTCOMMAND \ + "bootp;" \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \ + "bootm" +#define CONFIG_BOOTDELAY 5 + + +/*=================================================================== + * + * Board configuration settings - You should not need to modify these + * + *=================================================================== + */ + + +#include <cmd_confdefs.h> + + +/* + * Memory map + * + * This board runs in a standard CHRP (Map-B) configuration. + * + * Type Start End Size Width Chip Sel + * ----------- ----------- ----------- ------- ------- -------- + * SDRAM 0x00000000 0x04000000 64MB 64b SDRAMCS0 + * User LED's 0x78000000 RCS3 + * UART 0x7C000000 RCS2 + * Mailbox 0xFF000000 RCS1 + * Flash 0xFFC00000 0xFFFFFFFF 4MB 64b RCS0 + * + * Flash sectors are laid out as follows. + * + * Sector Start End Size Comments + * ------- ----------- ----------- ------- ----------- + * 0 0xFFC00000 0xFFC3FFFF 256KB + * 1 0xFFC40000 0xFFC7FFFF 256KB + * 2 0xFFC80000 0xFFCBFFFF 256KB + * 3 0xFFCC0000 0xFFCFFFFF 256KB + * 4 0xFFD00000 0xFFD3FFFF 256KB + * 5 0xFFD40000 0xFFD7FFFF 256KB + * 6 0xFFD80000 0xFFDBFFFF 256KB + * 7 0xFFDC0000 0xFFDFFFFF 256KB + * 8 0xFFE00000 0xFFE3FFFF 256KB + * 9 0xFFE40000 0xFFE7FFFF 256KB + * 10 0xFFE80000 0xFFEBFFFF 256KB + * 11 0xFFEC0000 0xFFEFFFFF 256KB + * 12 0xFFF00000 0xFFF3FFFF 256KB U-Boot code here + * 13 0xFFF40000 0xFFF7FFFF 256KB + * 14 0xFFF80000 0xFFFBFFFF 256KB + * 15 0xFFFC0000 0xFFFDFFFF 128KB + * 16 0xFFFE0000 0xFFFE7FFF 32KB U-Boot env vars here + * 17 0xFFFE8000 0xFFFEFFFF 32KB U-Boot backup copy of env vars here + * 18 0xFFFF0000 0xFFFFFFFF 64KB + */ + + +/* + * SDRAM config - see memory map details above. + * + * CFG_SDRAM_BASE - Start address of SDRAM, this _must_ be zero! + * CFG_SDRAM_SIZE - Total size of contiguous SDRAM bank(s) + */ + +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_SDRAM_SIZE 0x04000000 + + +/* + * Flash config - see memory map details above. + * + * CFG_FLASH_BASE - Start address of flash memory + * CFG_FLASH_SIZE - Total size of contiguous flash mem + * CFG_FLASH_ERASE_TOUT - Erase timeout in ms + * CFG_FLASH_WRITE_TOUT - Write timeout in ms + * CFG_MAX_FLASH_BANKS - Number of banks of flash on board + * CFG_MAX_FLASH_SECT - Number of sectors in a bank + */ + +#define CFG_FLASH_BASE 0xFFC00000 +#define CFG_FLASH_SIZE 0x00400000 +#define CFG_FLASH_ERASE_TOUT 250000 +#define CFG_FLASH_WRITE_TOUT 5000 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 19 + + +/* + * Monitor config - see memory map details above + * + * CFG_MONITOR_BASE - Base address of monitor code + * CFG_MALLOC_LEN - Size of malloc pool (128KB) + */ + +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_MALLOC_LEN 0x20000 + + +/* + * Command shell settings + * + * CFG_BARGSIZE - Boot Argument buffer size + * CFG_BOOTMAPSZ - Size of app's mapped RAM at boot (Linux=8MB) + * CFG_CBSIZE - Console Buffer (input) size + * CFG_LOAD_ADDR - Default load address + * CFG_LONGHELP - Provide more detailed help + * CFG_MAXARGS - Number of args accepted by monitor commands + * CFG_MEMTEST_START - Start address of test to run on RAM + * CFG_MEMTEST_END - End address of RAM test + * CFG_PBSIZE - Print Buffer (output) size + * CFG_PROMPT - Prompt string + */ + +#define CFG_BARGSIZE 1024 +#define CFG_BOOTMAPSZ 0x800000 +#define CFG_CBSIZE 1024 +#define CFG_LOAD_ADDR 0x100000 +#define CFG_LONGHELP +#define CFG_MAXARGS 16 +#define CFG_MEMTEST_START 0x00040000 +#define CFG_MEMTEST_END 0x00040100 +#define CFG_PBSIZE 1024 +#define CFG_PROMPT "=> " + + +/* + * Environment config - see memory map details above + * + * CFG_ENV_IS_IN_FLASH - The env variables are stored in flash + * CFG_ENV_ADDR - Address of the sector containing env vars + * CFG_ENV_SIZE - Ammount of RAM for env vars (used to save RAM, 4KB) + * CFG_ENV_SECT_SIZE - Size of sector containing env vars (32KB) + */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0xFFFE0000 +#define CFG_ENV_SIZE 0x1000 +#define CFG_ENV_ADDR_REDUND 0xFFFE8000 +#define CFG_ENV_SIZE_REDUND 0x1000 +#define CFG_ENV_SECT_SIZE 0x8000 + + +/* + * Initial RAM config + * + * Since the main system RAM is initialised very early, we place the INIT_RAM + * in the main system RAM just above the exception vectors. The contents are + * copied to top of RAM by the init code. + * + * CFG_INIT_RAM_ADDR - Address of Init RAM, above exception vect + * CFG_INIT_RAM_END - Size of Init RAM + * CFG_GBL_DATA_SIZE - Ammount of RAM to reserve for global data + * CFG_GBL_DATA_OFFSET - Start of global data, top of stack + */ + +#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + 0x4000) +#define CFG_INIT_RAM_END 0x4000 +#define CFG_GBL_DATA_SIZE 128 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + + +/* + * Initial BAT config + * + * BAT0 - System SDRAM + * BAT1 - LED's and Serial Port + * BAT2 - PCI Memory + * BAT3 - PCI I/O including Flash Memory + */ + +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_64M | BATU_VS | BATU_VP) +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U + +#define CFG_IBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT1L (0x70000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT1U (0x70000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT2L (0x80000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_IBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_DBAT3L (0xF0000000 | BATL_PP_RW | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CFG_DBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + + +/* + * Cache config + * + * CFG_CACHELINE_SIZE - Size of a cache line (CPU specific) + * CFG_L2 - L2 cache enabled if defined + * L2_INIT - L2 cache init flags + * L2_ENABLE - L2 cache enable flags + */ + +#define CFG_CACHELINE_SIZE 32 +#undef CFG_L2 +#define L2_INIT 0 +#define L2_ENABLE 0 + + +/* + * Clocks config + * + * CFG_BUS_HZ - Bus clock frequency in Hz + * CFG_BUS_CLK - As above (?) + * CFG_HZ - Decrementer freq in Hz + */ + +#define CFG_BUS_HZ CONFIG_BUS_CLK +#define CFG_BUS_CLK CONFIG_BUS_CLK +#define CFG_HZ 1000 + + +/* + * Serial port config + * + * CFG_BAUDRATE_TABLE - List of valid baud rates + * CFG_NS16550 - Include the NS16550 driver + * CFG_NS16550_SERIAL - Include the serial (wrapper) driver + * CFG_NS16550_CLK - Frequency of reference clock + * CFG_NS16550_REG_SIZE - 64-bit accesses to 8-bit port + * CFG_NS16550_COM1 - Base address of 1st serial port + */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_CLK 3686400 +#define CFG_NS16550_REG_SIZE -8 +#define CFG_NS16550_COM1 0x7C000000 + + +/* + * PCI Config - Address Map B (CHRP) + */ + +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x40000000 +#define CFG_PCI_MEM_BUS 0x80000000 +#define CFG_PCI_MEM_PHYS 0x80000000 +#define CFG_PCI_MEM_SIZE 0x7D000000 +#define CFG_ISA_MEM_BUS 0x00000000 +#define CFG_ISA_MEM_PHYS 0xFD000000 +#define CFG_ISA_MEM_SIZE 0x01000000 +#define CFG_PCI_IO_BUS 0x00800000 +#define CFG_PCI_IO_PHYS 0xFE800000 +#define CFG_PCI_IO_SIZE 0x00400000 +#define CFG_ISA_IO_BUS 0x00000000 +#define CFG_ISA_IO_PHYS 0xFE000000 +#define CFG_ISA_IO_SIZE 0x00800000 +#define CFG_ISA_IO_BASE_ADDRESS CFG_ISA_IO_PHYS +#define CFG_ISA_IO CFG_ISA_IO_PHYS +#define CFG_60X_PCI_IO_OFFSET CFG_ISA_IO_PHYS + + +/* + * Extra init functions + * + * CFG_BOARD_ASM_INIT - Call assembly init code + */ + +#define CFG_BOARD_ASM_INIT + + +/* + * Boot flags + * + * BOOTFLAG_COLD - Indicates a power-on boot + * BOOTFLAG_WARM - Indicates a software reset + */ + +#define BOOTFLAG_COLD 0x01 +#define BOOTFLAG_WARM 0x02 + + +#endif /* __CONFIG_H */ diff --git a/include/configs/spieval.h b/include/configs/spieval.h index 96cb6e4..9ebb51e 100644 --- a/include/configs/spieval.h +++ b/include/configs/spieval.h @@ -191,16 +191,6 @@ #undef CONFIG_BOOTARGS -#if defined (CONFIG_TQM5200_AA) -# define CONFIG_U_BOOT_SUFFIX "-AA\0" -#elif defined (CONFIG_TQM5200_AB) -# define CONFIG_U_BOOT_SUFFIX "-AB\0" -#elif defined (CONFIG_TQM5200_AC) -# define CONFIG_U_BOOT_SUFFIX "-AC\0" -#else -# define CONFIG_U_BOOT_SUFFIX "\0" -#endif - #define CONFIG_EXTRA_ENV_SETTINGS \ "netdev=eth0\0" \ "rootpath=/opt/eldk/ppc_6xx\0" \ @@ -217,7 +207,7 @@ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ "bootfile=/tftpboot/tqm5200/uImage\0" \ "load=tftp 200000 ${u-boot}\0" \ - "u-boot=/tftpboot/tqm5200/u-boot.bin" CONFIG_U_BOOT_SUFFIX \ + "u-boot=/tftpboot/tqm5200/u-boot.bin\0" \ "update=protect off FC000000 FC05FFFF;" \ "erase FC000000 FC05FFFF;" \ "cp.b 200000 FC000000 ${filesize};" \ @@ -283,13 +273,6 @@ #endif /* List of I2C addresses to be verified by POST */ -#if defined (CONFIG_TQM5200_AA) || defined (CONFIG_TQM5200_AB) -#define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \ - CFG_I2C_SLAVE } -#elif defined (CONFIG_TQM5200_AC) -#define I2C_ADDR_LIST { CFG_I2C_SLAVE } -#endif - #if defined (CONFIG_MINIFAP) #undef I2C_ADDR_LIST #define I2C_ADDR_LIST { CFG_I2C_EEPROM_ADDR, \ @@ -478,13 +461,9 @@ * SRAM - Do not map below 2 GB in address space, because this area is used * for SDRAM autosizing. */ -#if defined CONFIG_TQM5200_AB || defined (CONFIG_CS_AUTOCONF) +#if defined (CONFIG_CS_AUTOCONF) #define CFG_CS2_START 0xE5000000 -#ifdef CONFIG_TQM5200_AB -#define CFG_CS2_SIZE 0x80000 /* 512 kByte */ -#else /* CONFIG_CS_AUTOCONF */ #define CFG_CS2_SIZE 0x100000 /* 1 MByte */ -#endif #define CFG_CS2_CFG 0x0004D930 #endif @@ -492,8 +471,7 @@ * Grafic controller - Do not map below 2 GB in address space, because this * area is used for SDRAM autosizing. */ -#if defined (CONFIG_TQM5200_AB) || defined (CONFIG_TQM5200_AC) || \ - defined (CONFIG_CS_AUTOCONF) +#if defined (CONFIG_CS_AUTOCONF) #define SM501_FB_BASE 0xE0000000 #define CFG_CS1_START (SM501_FB_BASE) #define CFG_CS1_SIZE 0x4000000 /* 64 MByte */ diff --git a/include/configs/trab.h b/include/configs/trab.h index b6d4bcf..935aca2d 100644 --- a/include/configs/trab.h +++ b/include/configs/trab.h @@ -165,7 +165,6 @@ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_FAT | \ - CFG_CMD_JFFS2 | \ CFG_CMD_NFS | \ CFG_CMD_SNTP | \ CFG_CMD_USB ) @@ -179,7 +178,6 @@ CFG_CMD_DATE | \ CFG_CMD_DHCP | \ CFG_CMD_FAT | \ - CFG_CMD_JFFS2 | \ CFG_CMD_NFS | \ CFG_CMD_SNTP | \ CFG_CMD_USB ) @@ -389,10 +387,10 @@ #define MTDIDS_DEFAULT "nor0=0" /* production flash layout */ -#define MTDPARTS_DEFAULT "mtdparts=0:32k(Firmware1)ro," \ +#define MTDPARTS_DEFAULT "mtdparts=0:16k(Firmware1)ro," \ "16k(Env1)," \ "16k(Env2)," \ - "320k(Firmware2)ro," \ + "336k(Firmware2)ro," \ "896k(Kernel)," \ "5376k(Root-FS)," \ "1408k(JFFS2)," \ diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h index c5ee78f..4e97b01 100644 --- a/include/configs/voiceblue.h +++ b/include/configs/voiceblue.h @@ -47,6 +47,8 @@ #define CONFIG_SETUP_MEMORY_TAGS 1 #define CONFIG_INITRD_TAG 1 +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + /* * Physical Memory Map */ @@ -94,7 +96,6 @@ #define CONFIG_ENV_OVERWRITE -#define CFG_JFFS_CUSTOM_PART /* see board/voiceblue/jffs2parts.c */ #endif /* @@ -104,9 +105,11 @@ #ifdef VOICEBLUE_SMALL_FLASH #define CFG_MALLOC_LEN (SZ_64K - CFG_GBL_DATA_SIZE) #define CONFIG_STACKSIZE SZ_8K +#define PHYS_SDRAM_1_RESERVED 0 #else #define CFG_MALLOC_LEN SZ_4M #define CONFIG_STACKSIZE SZ_1M +#define PHYS_SDRAM_1_RESERVED (CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE) #endif /* @@ -174,6 +177,7 @@ #define CONFIG_BOOTCOMMAND "run nboot" #define CONFIG_PREBOOT "run setup" #define CONFIG_EXTRA_ENV_SETTINGS \ + "silent=1\0" \ "ospart=0\0" \ "swapos=no\0" \ "setpart=" \ @@ -185,15 +189,37 @@ "fi\0" \ "setup=setenv bootargs console=ttyS0,$baudrate " \ "mtdparts=$mtdparts\0" \ - "nfsargs=run setpart; setenv bootargs $bootargs " \ - "root=/dev/nfs ip=dhcp\0" \ + "nfsargs=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \ + "nfsroot=$rootpath root=/dev/nfs\0" \ "flashargs=run setpart; setenv bootargs $bootargs " \ "root=/dev/mtdblock$partition ro " \ "rootfstype=jffs2\0" \ - "nboot=run nfsargs; bootp; tftp; bootm\0" \ - "fboot=run flashargs; fsload /boot/uImage; bootm\0" + "initrdargs=setenv bootargs $bootargs " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \ + "fboot=run flashargs; fsload /boot/uImage; bootm\0" \ + "iboot=bootp; run initrdargs; tftp; bootm\0" \ + "nboot=bootp; run nfsargs; tftp; bootm\0" #endif +#ifndef VOICEBLUE_SMALL_FLASH +#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */ + +#if 1 /* feel free to disable for development */ +#define CONFIG_AUTOBOOT_KEYED /* Enable password protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nVoiceBlue Enterprise - booting...\n" +#define CONFIG_AUTOBOOT_DELAY_STR "." /* 1st "password" */ +#endif + +/* + * JFFS2 partitions (mtdparts command line support) + */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=omapflash.0" +#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)" + +#endif /* VOICEBLUE_SMALL_FLASH */ + /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -213,7 +239,7 @@ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_MEMTEST_START PHYS_SDRAM_1 -#define CFG_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE +#define CFG_MEMTEST_END PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED #undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ @@ -247,22 +273,4 @@ #define VOICEBLUE_LED_REG 0x04030000 -/* - * JFFS2 partitions - * - */ -/* No command line, one static partition */ -#undef CONFIG_JFFS2_CMDLINE -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00040000 - -/* mtdparts command line support */ -/* Note: fake mtd_id used, no linux mtd map file */ -/* -#define CONFIG_JFFS2_CMDLINE -#define MTDIDS_DEFAULT "nor0=voiceblue-0" -#define MTDPARTS_DEFAULT "mtdparts=voiceblue-0:128k(uboot),64k(env),64k(renv),-(jffs2)" -*/ - #endif /* __CONFIG_H */ |