diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/da850evm.h | 54 | ||||
| -rw-r--r-- | include/configs/igep0020.h | 228 | ||||
| -rw-r--r-- | include/configs/igep0030.h | 215 | ||||
| -rw-r--r-- | include/configs/omap3_beagle.h | 15 | ||||
| -rw-r--r-- | include/configs/omap3_overo.h | 14 | ||||
| -rw-r--r-- | include/configs/omap4_panda.h | 23 | ||||
| -rw-r--r-- | include/configs/omap4_sdp4430.h | 35 | ||||
| -rw-r--r-- | include/configs/qong.h | 21 |
8 files changed, 554 insertions, 51 deletions
diff --git a/include/configs/da850evm.h b/include/configs/da850evm.h index e0a3bae..7bf6336 100644 --- a/include/configs/da850evm.h +++ b/include/configs/da850evm.h @@ -26,6 +26,7 @@ /* * Board */ +#define CONFIG_DRIVER_TI_EMAC /* * SoC Configuration @@ -79,6 +80,43 @@ #define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ /* + * Flash & Environment + */ +#ifdef CONFIG_USE_NAND +#undef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_NAND_DAVINCI +#define CONFIG_SYS_NO_FLASH +#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +#define CONFIG_ENV_SIZE (128 << 10) +#define CONFIG_SYS_NAND_USE_FLASH_BBT +#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST +#define CONFIG_SYS_NAND_PAGE_2K +#define CONFIG_SYS_NAND_CS 3 +#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE3_BASE +#define CONFIG_SYS_CLE_MASK 0x10 +#define CONFIG_SYS_ALE_MASK 0x8 +#undef CONFIG_SYS_NAND_HW_ECC +#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 +#define DEF_BOOTM "" +#endif + +/* + * Network & Ethernet Configuration + */ +#ifdef CONFIG_DRIVER_TI_EMAC +#define CONFIG_EMAC_MDIO_PHY_NUM 0 +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_NET_MULTI +#endif + +/* * U-Boot general configuration */ #define CONFIG_BOOTFILE "uImage" /* Boot file name */ @@ -100,7 +138,7 @@ /* * Linux Information */ -#define LINUX_BOOT_PARAM_ADDR (CONFIG_SYS_MEMTEST_START + 0x100) +#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100) #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTARGS \ @@ -127,6 +165,20 @@ #undef CONFIG_CMD_PING #endif +#ifdef CONFIG_USE_NAND +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +#define CONFIG_CMD_NAND + +#define CONFIG_CMD_MTDPARTS +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define CONFIG_LZO +#define CONFIG_RBTREE +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#endif + #if !defined(CONFIG_USE_NAND) && \ !defined(CONFIG_USE_NOR) && \ !defined(CONFIG_USE_SPIFLASH) diff --git a/include/configs/igep0020.h b/include/configs/igep0020.h new file mode 100644 index 0000000..34e8a57 --- /dev/null +++ b/include/configs/igep0020.h @@ -0,0 +1,228 @@ +/* + * (C) Copyright 2010 + * ISEE 2007 SL, <www.iseebcn.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> + +/* + * High Level Configuration Options + */ +#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP34XX 1 /* which is a 34XX */ +#define CONFIG_OMAP3430 1 /* which is in a 3430 */ +#define CONFIG_OMAP3_IGEP0020 1 /* working with IGEP0020 */ + +#define CONFIG_SDRC /* The chip has SDRC controller */ + +#include <asm/arch/cpu.h> +#include <asm/arch/omap3.h> + +/* + * Display CPU and Board information + */ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK >> 1) + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* + * NS16550 Configuration + */ + +#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK + +/* select serial console configuration */ +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 +#define CONFIG_SERIAL3 3 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#define CONFIG_MMC 1 +#define CONFIG_OMAP3_MMC 1 +#define CONFIG_DOS_PARTITION 1 + +/* DDR */ +#define CONFIG_OMAP3_NUMONYX_DDR 1 + +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 + +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "IGEP" + +/* commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_EXT2 /* EXT2 Support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_ONENAND /* ONENAND support */ +#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_CMD_NFS /* NFS support */ +#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ +#define CONFIG_MTD_DEVICE + +#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ +#undef CONFIG_CMD_IMLS /* List all found images */ + +#define CONFIG_SYS_NO_FLASH +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_BUS 0 +#define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_DRIVER_OMAP34XX_I2C 1 + +/* + * TWL4030 + */ +#define CONFIG_TWL4030_POWER 1 + +/* Environment information */ +#define CONFIG_BOOTCOMMAND \ + "mmc init 0 ; fatload mmc 0 0x80000000 setup.ini ; source \0" + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbtty=cdc_acm\0" + +#define CONFIG_AUTO_COMPLETE 1 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "U-Boot # " +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ + /* works on */ +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ + 0x01F00000) /* 31MB */ + +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ + /* load address */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) + +/* + * OMAP3 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. + */ +#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ + +/* + * Physical Memory Map + * + */ +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */ +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 + +/* SDRAM Bank Allocation method */ +#define SDRC_R_B_C 1 + +/* + * FLASH and environment organization + */ + +#define PISMO1_ONEN_SIZE GPMC_SIZE_128M /* Configure the PISMO */ + +#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP + +#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ + +#define CONFIG_ENV_IS_IN_ONENAND 1 +#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */ +#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes for initial data */ + +/* + * SMSC911x Ethernet + */ +#if defined(CONFIG_CMD_NET) +#define CONFIG_NET_MULTI +#define CONFIG_SMC911X +#define CONFIG_SMC911X_32_BIT +#define CONFIG_SMC911X_BASE 0x2C000000 +#endif /* (CONFIG_CMD_NET) */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + +#endif /* __CONFIG_H */ diff --git a/include/configs/igep0030.h b/include/configs/igep0030.h new file mode 100644 index 0000000..5e2e0ed --- /dev/null +++ b/include/configs/igep0030.h @@ -0,0 +1,215 @@ +/* + * (C) Copyright 2010 + * ISEE 2007 SL, <www.iseebcn.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> + +/* + * High Level Configuration Options + */ +#define CONFIG_ARMV7 1 /* This is an ARM V7 CPU core */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP34XX 1 /* which is a 34XX */ +#define CONFIG_OMAP3430 1 /* which is in a 3430 */ +#define CONFIG_OMAP3_IGEP0030 1 /* working with IGEP0030 */ + +#define CONFIG_SDRC /* The chip has SDRC controller */ + +#include <asm/arch/cpu.h> +#include <asm/arch/omap3.h> + +/* + * Display CPU and Board information + */ +#define CONFIG_DISPLAY_CPUINFO 1 +#define CONFIG_DISPLAY_BOARDINFO 1 + +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK >> 1) + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 +#define CONFIG_REVISION_TAG 1 + +/* + * NS16550 Configuration + */ + +#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ + +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK + +/* select serial console configuration */ +#define CONFIG_CONS_INDEX 3 +#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 +#define CONFIG_SERIAL3 3 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#define CONFIG_MMC 1 +#define CONFIG_OMAP3_MMC 1 +#define CONFIG_DOS_PARTITION 1 + +/* DDR */ +#define CONFIG_OMAP3_NUMONYX_DDR 1 + +/* USB */ +#define CONFIG_MUSB_UDC 1 +#define CONFIG_USB_OMAP3 1 +#define CONFIG_TWL4030_USB 1 + +/* USB device configuration */ +#define CONFIG_USB_DEVICE 1 +#define CONFIG_USB_TTY 1 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 + +/* Change these to suit your needs */ +#define CONFIG_USBD_VENDORID 0x0451 +#define CONFIG_USBD_PRODUCTID 0x5678 +#define CONFIG_USBD_MANUFACTURER "Texas Instruments" +#define CONFIG_USBD_PRODUCT_NAME "IGEP" + +/* commands to include */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_EXT2 /* EXT2 Support */ +#define CONFIG_CMD_FAT /* FAT support */ +#define CONFIG_CMD_I2C /* I2C serial bus support */ +#define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_ONENAND /* ONENAND support */ +#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ +#define CONFIG_MTD_DEVICE + +#undef CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */ +#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ +#undef CONFIG_CMD_IMLS /* List all found images */ + +#define CONFIG_SYS_NO_FLASH +#define CONFIG_HARD_I2C 1 +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_SYS_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_BUS 0 +#define CONFIG_SYS_I2C_BUS_SELECT 1 +#define CONFIG_DRIVER_OMAP34XX_I2C 1 + +/* + * TWL4030 + */ +#define CONFIG_TWL4030_POWER 1 + +/* Environment information */ +#define CONFIG_BOOTCOMMAND \ + "mmc init 0 ; fatload mmc 0 0x80000000 setup.ini ; source \0" + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "usbtty=cdc_acm\0" + +#define CONFIG_AUTO_COMPLETE 1 + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_PROMPT "U-Boot # " +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) + +#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0) /* memtest */ + /* works on */ +#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \ + 0x01F00000) /* 31MB */ + +#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ + /* load address */ + +#define CONFIG_SYS_MONITOR_LEN (256 << 10) + +/* + * OMAP3 has 12 GP timers, they can be driven by the system clock + * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). + * This rate is divided by a local divisor. + */ +#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_HZ 1000 + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ + +/* + * Physical Memory Map + * + */ +#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ +#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 +#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 meg */ +#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 + +/* SDRAM Bank Allocation method */ +#define SDRC_R_B_C 1 + +/* + * FLASH and environment organization + */ + +#define PISMO1_ONEN_SIZE GPMC_SIZE_128M /* Configure the PISMO */ + +#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP + +#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ + +#define CONFIG_ENV_IS_IN_ONENAND 1 +#define CONFIG_ENV_SIZE (512 << 10) /* Total Size Environment */ +#define CONFIG_ENV_ADDR ONENAND_ENV_OFFSET + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10)) +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes for initial data */ + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + +#endif /* __CONFIG_H */ diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 1bd0f37..bbb1073 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -95,8 +95,9 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} +#define CONFIG_GENERIC_MMC 1 #define CONFIG_MMC 1 -#define CONFIG_OMAP3_MMC 1 +#define CONFIG_OMAP_HSMMC 1 #define CONFIG_DOS_PARTITION 1 /* DDR - I use Micron DDR */ @@ -111,11 +112,6 @@ #define CONFIG_USB_DEVICE 1 #define CONFIG_USB_TTY 1 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "Beagle" /* commands to include */ #include <config_cmd_default.h> @@ -189,6 +185,7 @@ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ "defaultdisplay=dvi\0" \ + "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext3 rootwait\0" \ "nandroot=/dev/mtdblock4 rw\0" \ @@ -209,10 +206,10 @@ "omapdss.def_disp=${defaultdisplay} " \ "root=${nandroot} " \ "rootfstype=${nandrootfstype}\0" \ - "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \ + "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source ${loadaddr}\0" \ - "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \ + "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "bootm ${loadaddr}\0" \ @@ -222,7 +219,7 @@ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ - "if mmc init; then " \ + "if mmc rescan ${mmcdev}; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h index a0e0f24..69f9126 100644 --- a/include/configs/omap3_overo.h +++ b/include/configs/omap3_overo.h @@ -87,8 +87,9 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \ 115200} +#define CONFIG_GENERIC_MMC 1 #define CONFIG_MMC 1 -#define CONFIG_OMAP3_MMC 1 +#define CONFIG_OMAP_HSMMC 1 #define CONFIG_DOS_PARTITION 1 /* DDR - I use Micron DDR */ @@ -97,6 +98,7 @@ /* commands to include */ #include <config_cmd_default.h> +#define CONFIG_CMD_CACHE #define CONFIG_CMD_EXT2 /* EXT2 Support */ #define CONFIG_CMD_FAT /* FAT support */ #define CONFIG_CMD_JFFS2 /* JFFS2 Support */ @@ -158,6 +160,7 @@ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ "defaultdisplay=dvi\0" \ + "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext3 rootwait\0" \ "nandroot=/dev/mtdblock4 rw\0" \ @@ -178,10 +181,10 @@ "omapdss.def_disp=${defaultdisplay} " \ "root=${nandroot} " \ "rootfstype=${nandrootfstype}\0" \ - "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \ + "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source ${loadaddr}\0" \ - "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \ + "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "bootm ${loadaddr}\0" \ @@ -191,7 +194,7 @@ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ - "if mmc init; then " \ + "if mmc rescan ${mmcdev}; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ @@ -321,4 +324,7 @@ extern unsigned int boot_flash_type; #endif /* (CONFIG_CMD_NET) */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h index a0d27a4..b52ca19 100644 --- a/include/configs/omap4_panda.h +++ b/include/configs/omap4_panda.h @@ -89,7 +89,6 @@ #define CONFIG_SYS_NS16550_COM3 UART3_BASE #define CONFIG_ENV_IS_NOWHERE -#define CONFIG_ENV_OVERWRITE #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} @@ -107,8 +106,9 @@ #define CONFIG_TWL6030_POWER 1 /* MMC */ +#define CONFIG_GENERIC_MMC 1 #define CONFIG_MMC 1 -#define CONFIG_OMAP3_MMC 1 +#define CONFIG_OMAP_HSMMC 1 #define CONFIG_SYS_MMC_SET_DEV 1 #define CONFIG_DOS_PARTITION 1 @@ -120,11 +120,6 @@ #define CONFIG_USB_DEVICE 1 #define CONFIG_USB_TTY 1 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "OMAP4 Panda" /* Flash */ #define CONFIG_SYS_NO_FLASH 1 @@ -144,18 +139,11 @@ #undef CONFIG_CMD_IMLS /* List all found images */ /* - * Enabling relocation of u-boot by default - * Relocation can be skipped if u-boot is copied to the TEXT_BASE - */ -#undef CONFIG_SKIP_RELOCATE_UBOOT - -/* * Environment setup */ #define CONFIG_BOOTDELAY 3 -/* allow overwriting serial config and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_EXTRA_ENV_SETTINGS \ @@ -163,7 +151,7 @@ "console=ttyS2,115200n8\0" \ "usbtty=cdc_acm\0" \ "vram=16M\0" \ - "mmcdev=1\0" \ + "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext3 rootwait\0" \ "mmcargs=setenv bootargs console=${console} " \ @@ -179,7 +167,7 @@ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ - "if mmc init ${mmcdev}; then " \ + "if mmc rescan ${mmcdev}; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ @@ -239,4 +227,7 @@ */ #define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h index d5439f9..174d73f 100644 --- a/include/configs/omap4_sdp4430.h +++ b/include/configs/omap4_sdp4430.h @@ -63,10 +63,10 @@ /* * Size of malloc() pool - * Total Size Environment - 256k + * Total Size Environment - 128k * Malloc - add 256k */ -#define CONFIG_ENV_SIZE (256 << 10) +#define CONFIG_ENV_SIZE (128 << 10) #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (256 << 10)) #define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */ /* initial data */ @@ -89,12 +89,9 @@ #define CONFIG_CONS_INDEX 3 #define CONFIG_SYS_NS16550_COM3 UART3_BASE -#define CONFIG_ENV_IS_NOWHERE -#define CONFIG_ENV_OVERWRITE #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\ 115200} - /* I2C */ #define CONFIG_HARD_I2C 1 #define CONFIG_SYS_I2C_SPEED 100000 @@ -108,11 +105,17 @@ #define CONFIG_TWL6030_POWER 1 /* MMC */ +#define CONFIG_GENERIC_MMC 1 #define CONFIG_MMC 1 -#define CONFIG_OMAP3_MMC 1 +#define CONFIG_OMAP_HSMMC 1 #define CONFIG_SYS_MMC_SET_DEV 1 #define CONFIG_DOS_PARTITION 1 +/* MMC ENV related defines */ +#define CONFIG_ENV_IS_IN_MMC 1 +#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */ +#define CONFIG_ENV_OFFSET 0xE0000 + /* USB */ #define CONFIG_MUSB_UDC 1 #define CONFIG_USB_OMAP3 1 @@ -121,11 +124,6 @@ #define CONFIG_USB_DEVICE 1 #define CONFIG_USB_TTY 1 #define CONFIG_SYS_CONSOLE_IS_IN_ENV 1 -/* Change these to suit your needs */ -#define CONFIG_USBD_VENDORID 0x0451 -#define CONFIG_USBD_PRODUCTID 0x5678 -#define CONFIG_USBD_MANUFACTURER "Texas Instruments" -#define CONFIG_USBD_PRODUCT_NAME "SDP4430" /* Flash */ #define CONFIG_SYS_NO_FLASH 1 @@ -138,6 +136,7 @@ #define CONFIG_CMD_FAT /* FAT support */ #define CONFIG_CMD_I2C /* I2C serial bus support */ #define CONFIG_CMD_MMC /* MMC support */ +#define CONFIG_CMD_SAVEENV /* Disabled commands */ #undef CONFIG_CMD_NET @@ -145,18 +144,11 @@ #undef CONFIG_CMD_IMLS /* List all found images */ /* - * Enabling relocation of u-boot by default - * Relocation can be skipped if u-boot is copied to the TEXT_BASE - */ -#undef CONFIG_SKIP_RELOCATE_UBOOT - -/* * Environment setup */ #define CONFIG_BOOTDELAY 3 -/* allow overwriting serial config and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_EXTRA_ENV_SETTINGS \ @@ -164,7 +156,7 @@ "console=ttyS2,115200n8\0" \ "usbtty=cdc_acm\0" \ "vram=16M\0" \ - "mmcdev=1\0" \ + "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext3 rootwait\0" \ "mmcargs=setenv bootargs console=${console} " \ @@ -180,7 +172,7 @@ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ - "if mmc init ${mmcdev}; then " \ + "if mmc rescan ${mmcdev}; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ @@ -240,4 +232,7 @@ */ #define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (LOW_LEVEL_SRAM_STACK - CONFIG_SYS_GBL_DATA_SIZE) + #endif /* __CONFIG_H */ diff --git a/include/configs/qong.h b/include/configs/qong.h index 7f284ef..f26ced1 100644 --- a/include/configs/qong.h +++ b/include/configs/qong.h @@ -66,8 +66,11 @@ #define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) /* FPGA */ +#define CONFIG_FPGA #define CONFIG_QONG_FPGA 1 #define CONFIG_FPGA_BASE (CS1_BASE) +#define CONFIG_FPGA_LATTICE +#define CONFIG_FPGA_COUNT 1 #ifdef CONFIG_QONG_FPGA /* Ethernet */ @@ -86,6 +89,22 @@ #define CONFIG_BMP_16BPP #define CONFIG_DISPLAY_COM57H5M10XRC +/* USB */ +#define CONFIG_CMD_USB +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI /* Enable EHCI USB support */ +#define CONFIG_USB_EHCI_MXC +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_MXC_USB_PORT 2 +#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT) +#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE +#define CONFIG_DOS_PARTITION +#define CONFIG_SUPPORT_VFAT +#define CONFIG_CMD_FAT +#endif /* CONFIG_CMD_USB */ + /* * Reducing the ARP timeout from default 5 seconds to 200ms we speed up the * initial TFTP transfer, should the user wish one, significantly. @@ -247,7 +266,7 @@ extern int qong_nand_rdy(void *chip); #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_SECT_SIZE 0x20000 #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) |