diff options
Diffstat (limited to 'include/configs')
112 files changed, 3133 insertions, 2693 deletions
diff --git a/include/configs/Alaska8220.h b/include/configs/Alaska8220.h index 3f2f614..38b962f 100644 --- a/include/configs/Alaska8220.h +++ b/include/configs/Alaska8220.h @@ -31,6 +31,8 @@ #define CONFIG_MPC8220 1 #define CONFIG_ALASKA8220 1 /* ... on Alaska board */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* Input clock running at 30Mhz, read Hid1 for the CPU multiplier to determine the CPU speed. */ #define CFG_MPC8220_CLKIN 30000000/* ... running at 30MHz */ diff --git a/include/configs/BC3450.h b/include/configs/BC3450.h index 706c13e..b7574bf 100644 --- a/include/configs/BC3450.h +++ b/include/configs/BC3450.h @@ -61,6 +61,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h index b248639..fd49f56 100644 --- a/include/configs/CPCI4052.h +++ b/include/configs/CPCI4052.h @@ -88,32 +88,17 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_ELF #define CONFIG_CMD_DATE -#define CONFIG_CMD_JFFS2 #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_CMD_BSP #define CONFIG_CMD_EEPROM - -#if 0 /* test-only */ -#define CONFIG_NETCONSOLE -#define CONFIG_NET_MULTI - -#ifdef CONFIG_NET_MULTI -#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */ -#endif -#endif - #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION #define CONFIG_SUPPORT_VFAT -#if 0 /* test-only */ -#define CONFIG_AUTO_UPDATE 1 /* autoupdate via compactflash */ -#endif - #undef CONFIG_WATCHDOG /* watchdog disabled */ #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */ @@ -256,29 +241,6 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/* - * JFFS2 partitions - */ - -/* No command line, one static partition, use whole device */ -#undef CONFIG_JFFS2_CMDLINE -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ - -/* Use first bank for JFFS2, second bank contains U-Boot. - * - * Note: fake mtd_id's used, no linux mtd map file. - */ -/* -#define CONFIG_JFFS2_CMDLINE -#define MTDIDS_DEFAULT "nor0=cpci4052-0" -#define MTDPARTS_DEFAULT "mtdparts=cpci4052-0:-(jffs2)" -*/ - #if 0 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- * NVRAM organization diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h index 1e9597d..55dd629 100644 --- a/include/configs/CPCI405AB.h +++ b/include/configs/CPCI405AB.h @@ -88,7 +88,6 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_ELF #define CONFIG_CMD_DATE -#define CONFIG_CMD_JFFS2 #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_PING @@ -238,27 +237,6 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -/* - * JFFS2 partitions - */ -/* No command line, one static partition */ -#undef CONFIG_JFFS2_CMDLINE -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ - -/* Use first bank for JFFS2, second bank contains U-Boot. - * - * Note: fake mtd_id's used, no linux mtd map file. - */ -/* -#define CONFIG_JFFS2_CMDLINE -#define MTDIDS_DEFAULT "nor0=cpci405ab-0" -#define MTDPARTS_DEFAULT "mtdparts=cpci405ab-0:-(jffs2)" -*/ - /*----------------------------------------------------------------------- * I2C EEPROM (CAT24WC32) for environment */ diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h index a8029ea..6b585be 100644 --- a/include/configs/CPCI405DT.h +++ b/include/configs/CPCI405DT.h @@ -87,23 +87,12 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_ELF #define CONFIG_CMD_DATE -#define CONFIG_CMD_JFFS2 #define CONFIG_CMD_I2C #define CONFIG_CMD_MII #define CONFIG_CMD_PING #define CONFIG_CMD_BSP #define CONFIG_CMD_EEPROM - -#if 0 /* test-only */ -#define CONFIG_NETCONSOLE -#define CONFIG_NET_MULTI - -#ifdef CONFIG_NET_MULTI -#define CONFIG_PHY1_ADDR 1 /* PHY address: for NetConsole */ -#endif -#endif - #define CONFIG_MAC_PARTITION #define CONFIG_DOS_PARTITION @@ -260,27 +249,6 @@ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -/* - * JFFS2 partitions - */ -/* No command line, one static partition */ -#undef CONFIG_JFFS2_CMDLINE -#define CONFIG_JFFS2_DEV "nor0" -#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF -#define CONFIG_JFFS2_PART_OFFSET 0x00000000 - -/* mtdparts command line support */ - -/* Use first bank for JFFS2, second bank contains U-Boot. - * - * Note: fake mtd_id's used, no linux mtd map file. - */ -/* -#define CONFIG_JFFS2_CMDLINE -#define MTDIDS_DEFAULT "nor0=cpci405dt-0" -#define MTDPARTS_DEFAULT "mtdparts=cpci405dt-0:-(jffs2)" -*/ - #if 0 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- * NVRAM organization @@ -416,7 +384,6 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - /* * Internal Definitions * diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h index 48e29a2..89edbde 100644 --- a/include/configs/CPCI750.h +++ b/include/configs/CPCI750.h @@ -61,6 +61,8 @@ #undef CONFIG_ECC /* enable ECC support */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* which initialization functions to call for this board */ #define CONFIG_MISC_INIT_R #define CONFIG_BOARD_PRE_INIT diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index f85cff7..3a347ea 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -37,6 +37,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h index 23508f9..59d0bdb 100644 --- a/include/configs/MPC8260ADS.h +++ b/include/configs/MPC8260ADS.h @@ -197,6 +197,13 @@ #define CONFIG_BAUDRATE 115200 +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#if defined(CONFIG_OF_LIBFDT) +#define OF_CPU "cpu@0" +#define OF_TBCLK (bd->bi_busfreq / 4) +#endif + /* * BOOTP options */ diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h index 610151f..d547681 100644 --- a/include/configs/MPC8313ERDB.h +++ b/include/configs/MPC8313ERDB.h @@ -469,6 +469,8 @@ #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR @ 0x00000000 */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h index e0a887c..095f665 100644 --- a/include/configs/MPC8315ERDB.h +++ b/include/configs/MPC8315ERDB.h @@ -203,7 +203,7 @@ #define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ | OR_UPM_XAM \ | OR_GPCM_CSNT \ - | OR_GPCM_ACS_0b11 \ + | OR_GPCM_ACS_DIV2 \ | OR_GPCM_XACS \ | OR_GPCM_SCY_15 \ | OR_GPCM_TRLX \ @@ -453,6 +453,7 @@ /* * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h index 32f57ac..977c041 100644 --- a/include/configs/MPC8323ERDB.h +++ b/include/configs/MPC8323ERDB.h @@ -468,6 +468,7 @@ /* * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h index 1276a12..9ca2a2b 100644 --- a/include/configs/MPC832XEMDS.h +++ b/include/configs/MPC832XEMDS.h @@ -483,6 +483,8 @@ * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h index 119e7ac..8705838 100644 --- a/include/configs/MPC8349EMDS.h +++ b/include/configs/MPC8349EMDS.h @@ -157,7 +157,7 @@ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ - OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* window base at flash base */ #define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32 MB window size */ @@ -355,7 +355,6 @@ /* SPI */ #define CONFIG_MPC8XXX_SPI -#define CONFIG_HARD_SPI /* SPI with hardware support */ #undef CONFIG_SOFT_SPI /* SPI bit-banged */ /* GPIOs. Used as SPI chip selects */ @@ -626,6 +625,7 @@ #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR @ 0x00000000 */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h index c72de03..82d0686 100644 --- a/include/configs/MPC8349ITX.h +++ b/include/configs/MPC8349ITX.h @@ -211,7 +211,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V) #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ - OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) #define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE #define CFG_LBLAWAR0_PRELIM (LBLAWAR_EN | (0x13 + CFG_FLASH_SIZE_SHIFT)) @@ -236,7 +236,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CFG_LED_BASE 0xF9000000 #define CFG_BR2_PRELIM (CFG_LED_BASE | BR_PS_8 | BR_V) -#define CFG_OR2_PRELIM (OR_AM_2MB | OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \ +#define CFG_OR2_PRELIM (OR_AM_2MB | OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_XACS | OR_GPCM_SCY_9 | OR_GPCM_TRLX | \ OR_GPCM_EHTR | OR_GPCM_EAD) @@ -555,6 +555,7 @@ boards, we say we have two, but don't display a message if we find only one. */ #define CFG_HID0_FINAL CFG_HID0_INIT #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h index 983575e..b4bff9a 100644 --- a/include/configs/MPC8360EMDS.h +++ b/include/configs/MPC8360EMDS.h @@ -203,7 +203,7 @@ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ - OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ @@ -515,6 +515,8 @@ * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h index 7b7d6f5..ca8d53c 100644 --- a/include/configs/MPC8360ERDK.h +++ b/include/configs/MPC8360ERDK.h @@ -195,7 +195,7 @@ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) /* valid */ #define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ - OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_XACS | OR_GPCM_SCY_15 | \ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD) @@ -419,6 +419,8 @@ * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR: cache cacheable */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h index e92493a..0dd0279 100644 --- a/include/configs/MPC837XEMDS.h +++ b/include/configs/MPC837XEMDS.h @@ -239,7 +239,7 @@ #define CFG_OR0_PRELIM ( (~(CFG_FLASH_SIZE - 1) << 20) \ | OR_UPM_XAM \ | OR_GPCM_CSNT \ - | OR_GPCM_ACS_0b11 \ + | OR_GPCM_ACS_DIV2 \ | OR_GPCM_XACS \ | OR_GPCM_SCY_15 \ | OR_GPCM_TRLX \ @@ -502,6 +502,7 @@ /* * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ #define CFG_SDRAM_LOWER CFG_SDRAM_BASE diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h index f7e6fd2..29c2490 100644 --- a/include/configs/MPC837XERDB.h +++ b/include/configs/MPC837XERDB.h @@ -524,6 +524,8 @@ * MMU Setup */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR: cache cacheable */ #define CFG_SDRAM_LOWER CFG_SDRAM_BASE #define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000) diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 5719759..d1d3cc3 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -87,9 +87,6 @@ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 5b3ea05..a64565d 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -73,9 +73,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index ffe9e00..669f4d7c 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -77,19 +77,14 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */ /* * Only possible on E500 Version 2 or newer cores. */ #define CONFIG_ENABLE_36BIT_PHYS 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 -#define CFG_ALT_MEMTEST #define CONFIG_PANIC_HANG /* do not reset board on panic */ /* @@ -171,6 +166,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h index fc8ad88..acf6f0d 100644 --- a/include/configs/MPC8548CDS.h +++ b/include/configs/MPC8548CDS.h @@ -87,9 +87,6 @@ extern unsigned long get_clock_freq(void); */ #define CONFIG_ENABLE_36BIT_PHYS 1 -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index e838345..1948c0d 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -73,9 +73,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index 9c95cc6..edf8525 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -40,6 +40,7 @@ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ +#define CONFIG_MPC8560 1 #define CONFIG_PCI #define CONFIG_TSEC_ENET /* tsec ethernet support */ @@ -80,11 +81,8 @@ #define CONFIG_BTB /* toggle branch predition */ #define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ - #define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */ -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h index a7c69d2..9e6bb44 100644 --- a/include/configs/MPC8568MDS.h +++ b/include/configs/MPC8568MDS.h @@ -80,7 +80,6 @@ extern unsigned long get_clock_freq(void); #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest works on */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 15ff0ea..fc16890 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -55,6 +55,7 @@ #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported & enabled */ #define CONFIG_ALTIVEC 1 /* @@ -71,10 +72,8 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 -#define CFG_ALT_MEMTEST /* * Base addresses -- Note these are effective addresses where the diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 9acc3da..455e154 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -67,6 +67,7 @@ #define BANK_INTERLEAVING 0x22000000 #define SUPER_BANK_INTERLEAVING 0x23000000 +#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ #define CONFIG_ALTIVEC 1 @@ -86,7 +87,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 diff --git a/include/configs/MVBLM7.h b/include/configs/MVBLM7.h new file mode 100644 index 0000000..b412655 --- /dev/null +++ b/include/configs/MVBLM7.h @@ -0,0 +1,480 @@ +/* + * Copyright (C) Matrix Vision GmbH 2008 + * + * Matrix Vision mvBlueLYNX-M7 configuration file + * based on Freescale's MPC8349ITX. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <version.h> + +/* + * High Level Configuration Options + */ +#define CONFIG_E300 1 +#define CONFIG_MPC83XX 1 +#define CONFIG_MPC834X 1 +#define CONFIG_MPC8343 1 + +#define CFG_IMMR 0xE0000000 + +#define CONFIG_PCI +#define CONFIG_83XX_GENERIC_PCI +#define CONFIG_PCI_SKIP_HOST_BRIDGE +#define CONFIG_HARD_I2C +#define CONFIG_TSEC_ENET +#define CONFIG_MPC8XXX_SPI +#define CONFIG_HARD_SPI +#define MVBLM7_MMC_CS 0x04000000 + +/* I2C */ +#undef CONFIG_SOFT_I2C + +#define CONFIG_FSL_I2C +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CFG_I2C_OFFSET 0x3000 +#define CFG_I2C2_OFFSET 0x3100 + +#define CFG_I2C_SPEED 100000 +#define CFG_I2C_SLAVE 0x7F + +/* + * DDR Setup + */ +#define CFG_DDR_BASE 0x00000000 +#define CFG_SDRAM_BASE CFG_DDR_BASE +#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE +#define CFG_83XX_DDR_USES_CS0 1 +#define CFG_MEMTEST_START (60<<20) +#define CFG_MEMTEST_END (70<<20) + +#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ + DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05 + +#define CFG_DDR_SIZE 256 + +/* HC, 75Ohm, DDR-II, DRQ */ +#define CFG_DDRCDR 0x80000001 +/* EN, ODT_WR, 3BA, 14row, 10col */ +#define CFG_DDR_CS0_CONFIG 0x80014102 +#define CFG_DDR_CS1_CONFIG 0x0 +#define CFG_DDR_CS2_CONFIG 0x0 +#define CFG_DDR_CS3_CONFIG 0x0 + +#define CFG_DDR_CS0_BNDS 0x0000000f +#define CFG_DDR_CS1_BNDS 0x0 +#define CFG_DDR_CS2_BNDS 0x0 +#define CFG_DDR_CS3_BNDS 0x0 + +#define CFG_DDR_CLK_CNTL 0x02000000 + +#define CFG_DDR_TIMING_0 0x00260802 +#define CFG_DDR_TIMING_1 0x2625b221 +#define CFG_DDR_TIMING_2 0x1f9820c7 +#define CFG_DDR_TIMING_3 0x00000000 + +/* ~MEM_EN, SREN, DDR-II, 32_BE */ +#define CFG_DDR_SDRAM_CFG 0x43080000 +#define CFG_DDR_SDRAM_CFG2 0x00401000 +#define CFG_DDR_INTERVAL 0x04060100 + +#define CFG_DDR_MODE 0x078e0232 + +/* Flash */ +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI_WIDTH FLASH_CFI_16BIT + +#define CFG_FLASH_BASE 0xFF800000 +#define CFG_FLASH_SIZE 8 +#define CFG_FLASH_SIZE_SHIFT 3 +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_ERASE_TOUT 60000 +#define CFG_FLASH_WRITE_TOUT 500 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 256 + +#define CFG_BR0_PRELIM (CFG_FLASH_BASE | BR_PS_16 | BR_V) +#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \ + OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS|\ + OR_GPCM_SCY_15 | OR_GPCM_TRLX | OR_GPCM_EHTR | \ + OR_GPCM_EAD) +#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE +#define CFG_LBLAWAR0_PRELIM (LBLAWAR_EN | (0x13 + CFG_FLASH_SIZE_SHIFT)) + +/* + * U-Boot memory configuration + */ +#define CFG_MONITOR_BASE TEXT_BASE +#undef CFG_RAMBOOT + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK +#define CFG_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x1000 /* End of used area in RAM*/ + +#define CFG_GBL_DATA_SIZE 0x100 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/* CFG_MONITOR_LEN must be a multiple of CFG_ENV_SECT_SIZE */ +#define CFG_MONITOR_LEN (512 * 1024) +#define CFG_MALLOC_LEN (512 * 1024) + +/* + * Local Bus LCRR and LBCR regs + * LCRR: DLL bypass, Clock divider is 4 + * External Local Bus rate is + * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV + */ +#define CFG_LCRR (LCRR_DBYP | LCRR_CLKDIV_4) +#define CFG_LBC_LBCR 0x00000000 + +/* LB sdram refresh timer, about 6us */ +#define CFG_LBC_LSRT 0x32000000 +/* LB refresh timer prescal, 266MHz/32*/ +#define CFG_LBC_MRTPR 0x20000000 + +/* + * Serial Port + */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} + +#define CONFIG_CONSOLE ttyS0 +#define CONFIG_BAUDRATE 115200 + +#define CFG_NS16550_COM1 (CFG_IMMR + 0x4500) +#define CFG_NS16550_COM2 (CFG_IMMR + 0x4600) + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 +#define MV_DTB_NAME "mvblm7.dtb" + +/* + * PCI + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x10000000 +#define CFG_PCI1_MMIO_BASE (CFG_PCI1_MEM_BASE + CFG_PCI1_MEM_SIZE) +#define CFG_PCI1_MMIO_PHYS CFG_PCI1_MMIO_BASE +#define CFG_PCI1_MMIO_SIZE 0x10000000 +#define CFG_PCI1_IO_BASE 0x00000000 +#define CFG_PCI1_IO_PHYS 0xE2000000 +#define CFG_PCI1_IO_SIZE 0x01000000 + +#define _IO_BASE 0x00000000 + +#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_RETRY_COUNT 3 + +#define PCI_66M +#define CONFIG_83XX_CLKIN 66666667 +#define CONFIG_PCI_PNP +#define CONFIG_PCI_SCAN_SHOW + +/* TSEC */ +#define CONFIG_GMII +#define CFG_VSC8601_SKEWFIX +#define CFG_VSC8601_SKEW_TX 3 +#define CFG_VSC8601_SKEW_RX 3 + +#define CONFIG_TSEC1 +#define CONFIG_TSEC2 + +#define CONFIG_HAS_ETH0 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_FEC1_PHY_NORXERR +#define CFG_TSEC1_OFFSET 0x24000 +#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET) +#define TSEC1_PHY_ADDR 0x10 +#define TSEC1_PHYIDX 0 +#define TSEC1_FLAGS (TSEC_GIGABIT|TSEC_REDUCED) + +#define CONFIG_HAS_ETH1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define CONFIG_FEC2_PHY_NORXERR +#define CFG_TSEC2_OFFSET 0x25000 +#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET) +#define TSEC2_PHY_ADDR 0x11 +#define TSEC2_PHYIDX 0 +#define TSEC2_FLAGS (TSEC_GIGABIT|TSEC_REDUCED) + +#define CONFIG_ETHPRIME "TSEC0" + +#define CONFIG_BOOTP_VENDOREX +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_NTPSERVER +#define CONFIG_BOOTP_RANDOM_DELAY +#define CONFIG_BOOTP_SEND_HOSTNAME + +/* USB */ +#define CONFIG_HAS_FSL_DR_USB + +/* + * Environment + */ +#undef CFG_FLASH_PROTECTION +#define CONFIG_ENV_OVERWRITE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0xFF800000 +#define CFG_ENV_SIZE 0x2000 +#define CFG_ENV_SECT_SIZE 0x2000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR+CFG_ENV_SIZE) +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE + +#define CONFIG_LOADS_ECHO +#define CFG_LOADS_BAUD_CHANGE + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_PCI +#define CONFIG_CMD_I2C +#define CONFIG_CMD_FPGA + +#undef CONFIG_WATCHDOG + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " + +/* default load address */ +#define CFG_LOAD_ADDR 0x2000000 +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 0x200000 + +#define CFG_PROMPT "mvBL-M7> " +#define CFG_CBSIZE 256 + +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_MAXARGS 16 +#define CFG_BARGSIZE CFG_CBSIZE +#define CFG_HZ 1000 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +#define CFG_HRCW_LOW 0x0 +#define CFG_HRCW_HIGH 0x0 + +/* + * System performance + */ +#define CFG_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */ +#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */ +#define CFG_SPCR_TSEC1EP 3 /* TSEC1 emergency priority (0-3) */ +#define CFG_SPCR_TSEC2EP 3 /* TSEC2 emergency priority (0-3) */ + +/* clocking */ +#define CFG_SCCR_ENCCM 0 +#define CFG_SCCR_USBMPHCM 0 +#define CFG_SCCR_USBDRCM 2 +#define CFG_SCCR_TSEC1CM 1 +#define CFG_SCCR_TSEC2CM 1 + +#define CFG_SICRH 0x1fff8003 +#define CFG_SICRL (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0) + +#define CFG_HID0_INIT 0x000000000 +#define CFG_HID0_FINAL CFG_HID0_INIT + +#define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 + +/* DDR */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* PCI */ +#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT2L (CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\ + BATL_GUARDEDSTORAGE) +#define CFG_IBAT2U (CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* no PCI2 */ +#define CFG_IBAT3L 0 +#define CFG_IBAT3U 0 +#define CFG_IBAT4L 0 +#define CFG_IBAT4U 0 + +/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */ +#define CFG_IBAT5L (CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | \ + BATL_GUARDEDSTORAGE) +#define CFG_IBAT5U (CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP) + +/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */ +#define CFG_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) +#define CFG_IBAT7L 0 +#define CFG_IBAT7U 0 + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U +#define CFG_DBAT4L CFG_IBAT4L +#define CFG_DBAT4U CFG_IBAT4U +#define CFG_DBAT5L CFG_IBAT5L +#define CFG_DBAT5U CFG_IBAT5U +#define CFG_DBAT6L CFG_IBAT6L +#define CFG_DBAT6U CFG_IBAT6U +#define CFG_DBAT7L CFG_IBAT7L +#define CFG_DBAT7U CFG_IBAT7U + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + + +/* + * Environment Configuration + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_NETDEV eth0 + +/* Default path and filenames */ +#define CONFIG_BOOTDELAY 5 +#define CONFIG_AUTOBOOT_KEYED +#define CONFIG_AUTOBOOT_STOP_STR "s" +#define CONFIG_ZERO_BOOTDELAY_CHECK +#define CONFIG_RESET_TO_RETRY 1000 + +#define MV_CI "mvBL-M7" +#define MV_VCI "mvBL-M7" +#define MV_FPGA_DATA "0xfff80000" +#define MV_FPGA_SIZE "0x76ca2" +#define MV_KERNEL_ADDR "0xff810000" +#define MV_INITRD_ADDR "0xffc00000" +#define MV_AUTOSCR_ADDR "0xff804000" +#define MV_AUTOSCR_ADDR2 "0xff806000" +#define MV_DTB_ADDR "0xff808000" +#define MV_INITRD_LENGTH "0x00300000" + +#define CONFIG_SHOW_BOOT_PROGRESS 1 + +#define MV_KERNEL_ADDR_RAM "0x00100000" +#define MV_DTB_ADDR_RAM "0x00600000" +#define MV_INITRD_ADDR_RAM "0x01000000" + +#define CONFIG_BOOTCOMMAND "if imi ${autoscr_addr}; \ + then autoscr ${autoscr_addr}; \ + else autoscr ${autoscr_addr2}; \ + fi;" +#define CONFIG_BOOTARGS "root=/dev/ram ro rootfstype=squashfs" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "console_nr=0\0" \ + "stdin=serial\0" \ + "stdout=serial\0" \ + "stderr=serial\0" \ + "fpga=0\0" \ + "fpgadata=" MV_FPGA_DATA "\0" \ + "fpgadatasize=" MV_FPGA_SIZE "\0" \ + "autoscr_addr=" MV_AUTOSCR_ADDR "\0" \ + "autoscr_addr2=" MV_AUTOSCR_ADDR2 "\0" \ + "mv_kernel_addr=" MV_KERNEL_ADDR "\0" \ + "mv_kernel_addr_ram=" MV_KERNEL_ADDR_RAM "\0" \ + "mv_initrd_addr=" MV_INITRD_ADDR "\0" \ + "mv_initrd_addr_ram=" MV_INITRD_ADDR_RAM "\0" \ + "mv_initrd_length=" MV_INITRD_LENGTH "\0" \ + "mv_dtb_addr=" MV_DTB_ADDR "\0" \ + "mv_dtb_addr_ram=" MV_DTB_ADDR_RAM "\0" \ + "dtb_name=" MV_DTB_NAME "\0" \ + "mv_version=" U_BOOT_VERSION "\0" \ + "dhcp_client_id=" MV_CI "\0" \ + "dhcp_vendor-class-identifier=" MV_VCI "\0" \ + "netretry=no\0" \ + "use_static_ipaddr=no\0" \ + "static_ipaddr=192.168.90.10\0" \ + "static_netmask=255.255.255.0\0" \ + "static_gateway=0.0.0.0\0" \ + "initrd_name=uInitrd.mvblm7-xenorfs\0" \ + "zcip=no\0" \ + "netboot=yes\0" \ + "mvtest=Ff\0" \ + "tried_bootfromflash=no\0" \ + "tried_bootfromnet=no\0" \ + "bootfile=mvblm72625.boot\0" \ + "use_dhcp=yes\0" \ + "gev_start=yes\0" \ + "mvbcdma_debug=0\0" \ + "mvbcia_debug=0\0" \ + "propdev_debug=0\0" \ + "gevss_debug=0\0" \ + "watchdog=0\0" \ + "usb_dr_mode=host\0" \ + "" + +#define CONFIG_FPGA_COUNT 1 +#define CONFIG_FPGA CFG_ALTERA_CYCLON2 +#define CONFIG_FPGA_ALTERA +#define CONFIG_FPGA_CYCLON2 + +#endif diff --git a/include/configs/MigoR.h b/include/configs/MigoR.h index 99e1179..fa0e5db 100644 --- a/include/configs/MigoR.h +++ b/include/configs/MigoR.h @@ -45,10 +45,6 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTARGS "console=ttySC0,115200 root=1f01" -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.10.100 -#define CONFIG_SERVERIP 192.168.10.77 -#define CONFIG_GATEWAYIP 192.168.10.77 #define CONFIG_VERSION_VARIABLE #undef CONFIG_SHOW_BOOT_PROGRESS diff --git a/include/configs/PM520.h b/include/configs/PM520.h index 6eb6444..259178f 100644 --- a/include/configs/PM520.h +++ b/include/configs/PM520.h @@ -40,6 +40,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index ff64378..8a53fdd 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -49,6 +49,7 @@ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_SBC8540 1 /* configuration for SBC8560 board */ +#define CONFIG_MPC8540 1 #define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific (supplement) */ diff --git a/include/configs/TB5200.h b/include/configs/TB5200.h index 6cb3022..d21783b 100644 --- a/include/configs/TB5200.h +++ b/include/configs/TB5200.h @@ -42,6 +42,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/TOP5200.h b/include/configs/TOP5200.h index 71fa36b..4c44735 100644 --- a/include/configs/TOP5200.h +++ b/include/configs/TOP5200.h @@ -50,6 +50,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h index bff2edf..bfb478a 100644 --- a/include/configs/TQM5200.h +++ b/include/configs/TQM5200.h @@ -47,6 +47,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h index a86939e..0d2ca72 100644 --- a/include/configs/TQM834x.h +++ b/include/configs/TQM834x.h @@ -113,7 +113,7 @@ extern int tqm834x_num_flash_banks; BR_MS_GPCM | BR_PS_32 | BR_V) /* FLASH timing (0x0000_0c54) */ -#define CFG_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_0b10 | \ +#define CFG_OR_TIMING_FLASH (OR_GPCM_CSNT | OR_GPCM_ACS_DIV4 | \ OR_GPCM_SCY_5 | OR_GPCM_TRLX) #define CFG_PRELIM_OR_AM 0xc0000000 /* OR addr mask: 1 GiB */ @@ -423,6 +423,8 @@ extern int tqm834x_num_flash_banks; #define CFG_HID0_FINAL CFG_HID0_INIT #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR 0 - 512M */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h index fca5f74..d18f234 100644 --- a/include/configs/TQM85xx.h +++ b/include/configs/TQM85xx.h @@ -1,4 +1,7 @@ /* + * (C) Copyright 2007 + * Thomas Waehner, TQ-System GmbH, thomas.waehner@tqs.de. + * * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * @@ -27,7 +30,7 @@ */ /* - * TQM85xx (8560/40/55/41) board configuration file + * TQM85xx (8560/40/55/41/48) board configuration file */ #ifndef __CONFIG_H @@ -39,25 +42,53 @@ #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */ #define CONFIG_PCI +#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ +#define CONFIG_PCIX_CHECK /* PCIX olny works at 66 MHz */ +#ifdef CONFIG_TQM8548 +#define CONFIG_PCI1 +#define CONFIG_PCIE1 +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ +#endif + #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ + /* + * Configuration for big NOR Flashes + * + * Define CONFIG_TQM_BIGFLASH for boards with more than 128 MiB NOR Flash. + * Please be aware, that this changes the whole memory map (new CCSRBAR + * address, etc). You have to use an adapted Linux kernel or FDT blob + * if this option is set. + */ +#undef CONFIG_TQM_BIGFLASH + +/* + * NAND flash support (disabled by default) + * + * Warning: NAND support will likely increase the U-Boot image size + * to more than 256 KB. Please adjust TEXT_BASE if necessary. + */ +#undef CONFIG_NAND + /* - * Only MPC8540 doesn't have CPM module + * MPC8540 and MPC8548 don't have CPM module */ -#ifndef CONFIG_MPC8540 +#if !defined(CONFIG_MPC8540) && !defined(CONFIG_MPC8548) #define CONFIG_CPM2 1 /* has CPM2 */ #endif -#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ +#define CONFIG_FSL_LAW 1 /* Use common FSL init code */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support */ /* * sysclk for MPC85xx * * Two valid values are: - * 33000000 - * 66000000 + * 33333333 + * 66666666 * * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz * is likely the desired value here, so that is now the default. @@ -88,10 +119,18 @@ * actual resources get mapped (not physical addresses) */ #define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_CCSRBAR 0xA0000000 /* relocated CCSRBAR */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */ +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CFG_PCI1_ADDR (CFG_CCSRBAR + 0x8000) +#define CFG_PCI2_ADDR (CFG_CCSRBAR + 0x9000) +#define CFG_PCIE1_ADDR (CFG_CCSRBAR + 0xa000) + /* * DDR Setup */ @@ -102,65 +141,116 @@ /* TQM8540 & 8560 need DLL-override */ #define CONFIG_DDR_DLL /* DLL fix needed */ #define CONFIG_DDR_DEFAULT_CL 25 /* CAS latency 2,5 */ -#endif /* defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560) */ +#endif /* CONFIG_TQM8540 || CONFIG_TQM8560 */ -#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) +#if defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) || \ + defined(CONFIG_TQM8548) #define CONFIG_DDR_DEFAULT_CL 30 /* CAS latency 3 */ -#endif /* defined(CONFIG_TQM8541) || defined(CONFIG_TQM8555) */ +#endif /* CONFIG_TQM8541 || CONFIG_TQM8555 || CONFIG_TQM8548 */ + +/* + * Old TQM85xx boards have 'M' type Spansion Flashes from the S29GLxxxM + * series while new boards have 'N' type Flashes from the S29GLxxxN + * series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB. + */ +#ifdef CONFIG_TQM8548 +#define CONFIG_TQM_FLASH_N_TYPE +#endif /* CONFIG_TQM8548 */ /* * Flash on the Local Bus */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_FLASH0 0xE0000000 +#define CFG_FLASH1 0xC0000000 +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_FLASH0 0xFC000000 #define CFG_FLASH1 0xF8000000 +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } #define CFG_LBC_FLASH_BASE CFG_FLASH1 /* Localbus flash start */ -#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +#define CFG_FLASH_BASE CFG_LBC_FLASH_BASE /* start of FLASH */ +/* Default ORx timings are for <= 41.7 MHz Local Bus Clock. + * + * Note: According to timing specifications external addr latch delay + * (EAD, bit #0) must be set if Local Bus Clock is > 83 MHz. + * + * For other Local Bus Clocks see following table: + * + * Clock/MHz CFG_ORx_PRELIM + * 166 0x.....CA5 + * 133 0x.....C85 + * 100 0x.....C65 + * 83 0x.....FA2 + * 66 0x.....C82 + * 50 0x.....C60 + * 42 0x.....040 + * 33 0x.....030 + * 25 0x.....020 + * + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_BR0_PRELIM 0xE0001801 /* port size 32bit */ +#define CFG_OR0_PRELIM 0xE0000040 /* 512MB Flash */ +#define CFG_BR1_PRELIM 0xC0001801 /* port size 32bit */ +#define CFG_OR1_PRELIM 0xE0000040 /* 512MB Flash */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_BR0_PRELIM 0xfc001801 /* port size 32bit */ #define CFG_OR0_PRELIM 0xfc000040 /* 64MB Flash */ #define CFG_BR1_PRELIM 0xf8001801 /* port size 32bit */ #define CFG_OR1_PRELIM 0xfc000040 /* 64MB Flash */ +#endif /* CONFIG_TQM_BIGFLASH */ -#define CFG_FLASH_CFI /* flash is CFI compat. */ -#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver*/ +#define CFG_FLASH_CFI /* flash is CFI compat. */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector */ #define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash*/ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* speed up output to Flash */ -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ -#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 512 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ #define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ #define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ -#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ -#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ -#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ +/* + * Note: when changing the Local Bus clock divider you have to + * change the timing values in CFG_ORx_PRELIM. + * + * LCRR[00:03] CLKDIV: System (CCB) clock divider. Valid values are 2, 4, 8. + * LCRR[16:17] EADC : External address delay cycles. It should be set to 2 + * for Local Bus Clock > 83.3 MHz. + */ +#define CFG_LBC_LCRR 0x00030008 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer presc.*/ #define CONFIG_L1_INIT_RAM #define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_ADDR (CFG_CCSRBAR \ + + 0x04010000) /* Initial RAM address */ #define CFG_INIT_RAM_END 0x4000 /* End used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data*/ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MONITOR_LEN (~TEXT_BASE + 1)/* Reserved for Monitor */ +#define CFG_MALLOC_LEN (384 * 1024) /* Reserved for malloc */ /* Serial Port */ #if defined(CONFIG_TQM8560) -#define CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ -#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ +#define CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ +#define CONFIG_CONS_INDEX 1 /* which serial channel for console */ -#else /* ! TQM8560 */ +#else /* !CONFIG_TQM8560 */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO @@ -173,20 +263,18 @@ #define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) /* PS/2 Keyboard */ -#if !defined(CONFIG_TQM8560) #define CONFIG_PS2KBD /* AT-PS/2 Keyboard */ #define CONFIG_PS2MULT /* .. on PS/2 Multiplexer */ #define CONFIG_PS2SERIAL 2 /* .. on DUART2 */ #define CONFIG_PS2MULT_DELAY (CFG_HZ/2) /* Initial delay */ #define CONFIG_BOARD_EARLY_INIT_R 1 -#endif /* !CONFIG_TQM8560 */ #endif /* CONFIG_TQM8560 */ -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ @@ -194,11 +282,25 @@ #define CFG_PROMPT_HUSH_PS2 "> " #endif +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + +/* CAN */ +#define CFG_CAN_BASE (CFG_CCSRBAR \ + + 0x03000000) /* CAN base address */ +#ifdef CONFIG_CAN_DRIVER +#define CFG_CAN_OR_AM 0xFFFF8000 /* 32 KiB address mask */ +#define CFG_OR2_CAN (CFG_CAN_OR_AM | OR_UPM_BI) +#define CFG_BR2_CAN ((CFG_CAN_BASE & BR_BA) | \ + BR_PS_8 | BR_MS_UPMC | BR_V) +#endif /* CONFIG_CAN_DRIVER */ /* * I2C */ -#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ @@ -219,7 +321,7 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ +#define CFG_I2C_MULTI_EEPROMS 1 /* more than one eeprom */ /* I2C SYSMON (LM75) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ @@ -228,10 +330,64 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 +#ifndef CONFIG_PCIE1 /* RapidIO MMU */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_RIO_MEM_BASE 0xb0000000 /* base address */ +#define CFG_RIO_MEM_SIZE 0x10000000 /* 256M */ +#else /* !CONFIG_TQM_BIGFLASH */ #define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */ +#endif /* CONFIG_TQM_BIGFLASH */ #define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ +#endif /* CONFIG_PCIE1 */ + +/* NAND FLASH */ +#ifdef CONFIG_NAND + +#undef CFG_NAND_LEGACY + +#define CONFIG_NAND_FSL_UPM 1 + +#define CONFIG_MTD_NAND_ECC_JFFS2 1 /* use JFFS2 ECC */ + +/* address distance between chip selects */ +#define CFG_NAND_SELECT_DEVICE 1 +#define CFG_NAND_CS_DIST 0x200 + +#define CFG_NAND_SIZE 0x8000 +#define CFG_NAND0_BASE (CFG_CCSRBAR + 0x03010000) +#define CFG_NAND1_BASE (CFG_NAND0_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND2_BASE (CFG_NAND1_BASE + CFG_NAND_CS_DIST) +#define CFG_NAND3_BASE (CFG_NAND2_BASE + CFG_NAND_CS_DIST) + +#define CFG_MAX_NAND_DEVICE 2 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 + +#if (CFG_MAX_NAND_DEVICE == 1) +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE } +#elif (CFG_MAX_NAND_DEVICE == 2) +#define CFG_NAND_QUIET_TEST 1 +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ +} +#elif (CFG_MAX_NAND_DEVICE == 4) +#define CFG_NAND_QUIET_TEST 1 +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE, \ + CFG_NAND1_BASE, \ + CFG_NAND2_BASE, \ + CFG_NAND3_BASE, \ +} +#endif + +/* CS3 for NAND Flash */ +#define CFG_BR3_PRELIM ((CFG_NAND0_BASE & BR_BA) | BR_PS_8 | \ + BR_MS_UPMB | BR_V) +#define CFG_OR3_PRELIM (P2SZ_TO_AM(CFG_NAND_SIZE) | OR_UPM_BI) + +#define NAND_BIG_DELAY_US 25 /* max tR for Samsung devices */ + +#endif /* CONFIG_NAND */ /* * General PCI @@ -240,9 +396,33 @@ #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_BASE (CFG_CCSRBAR + 0x02000000) #define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +/* PCI view of System Memory */ +#define CFG_PCI_MEMORY_BUS 0x00000000 +#define CFG_PCI_MEMORY_PHYS 0x00000000 +#define CFG_PCI_MEMORY_SIZE 0x80000000 + +#ifdef CONFIG_PCIE1 +/* + * General PCI express + * Addresses are mapped 1-1. + */ +#ifdef CONFIG_TQM_BIGFLASH +#define CFG_PCIE1_MEM_BASE 0xb0000000 +#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0xaf000000 +#else /* !CONFIG_TQM_BIGFLASH */ +#define CFG_PCIE1_MEM_BASE 0xc0000000 +#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCIE1_IO_BASE 0xef000000 +#endif /* CONFIG_TQM_BIGFLASH */ +#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE +#define CFG_PCIE1_IO_PHYS CFG_PCIE1_IO_BASE +#define CFG_PCIE1_IO_SIZE 0x1000000 /* 16M */ +#endif /* CONFIG_PCIE1 */ #if defined(CONFIG_PCI) @@ -254,8 +434,7 @@ #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ -#endif /* CONFIG_PCI */ - +#endif /* CONFIG_PCI */ #define CONFIG_NET_MULTI 1 @@ -277,6 +456,27 @@ #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 +#ifdef CONFIG_TQM8548 +/* + * TQM8548 has 4 ethernet ports. 4 ETSEC's. + * + * On the STK85xx Starterkit the ETSEC3/4 ports are on an + * additional adapter (AIO) between module and Starterkit. + */ +#define CONFIG_TSEC3 1 +#define CONFIG_TSEC3_NAME "TSEC2" +#define CONFIG_TSEC4 1 +#define CONFIG_TSEC4_NAME "TSEC3" +#define TSEC3_PHY_ADDR 4 +#define TSEC4_PHY_ADDR 5 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) +#define CONFIG_HAS_ETH3 +#define CONFIG_HAS_ETH4 +#endif /* CONFIG_TQM8548 */ + /* Options are TSEC[0-1], FEC */ #define CONFIG_ETHPRIME "TSEC0" @@ -305,7 +505,7 @@ * FCC2: a - c (X50.2 - 1) */ #define CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ +#define CONFIG_ETHER_INDEX 1 /* FCC channel for ethernet */ #endif #if defined(CONFIG_TQM8560) @@ -321,12 +521,13 @@ * FCC3: a - d (X50.2 - 3) */ #define CONFIG_ETHER_ON_FCC -#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ +#define CONFIG_ETHER_INDEX 3 /* FCC channel for ethernet */ #endif #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 1) #define CONFIG_ETHER_ON_FCC1 -#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) +#define CFG_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | \ + CMXFCR_TF1CS_MSK) #define CFG_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -334,7 +535,8 @@ #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2) #define CONFIG_ETHER_ON_FCC2 -#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +#define CFG_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | \ + CMXFCR_TF2CS_MSK) #define CFG_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK16 | CMXFCR_TF2CS_CLK13) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -342,7 +544,8 @@ #if defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 3) #define CONFIG_ETHER_ON_FCC3 -#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | CMXFCR_TF3CS_MSK) +#define CFG_CMXFCR_MASK3 (CMXFCR_FC3 | CMXFCR_RF3CS_MSK | \ + CMXFCR_TF3CS_MSK) #define CFG_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15 | CMXFCR_TF3CS_CLK14) #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) @@ -352,17 +555,21 @@ * Environment */ #define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x20000) -#define CFG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ + +#ifdef CONFIG_TQM_FLASH_N_TYPE +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K (one sector) for env */ +#else /* !CONFIG_TQM_FLASH_N_TYPE */ +#define CFG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) for env */ +#endif /* CONFIG_TQM_FLASH_N_TYPE */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE - CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE 0x2000 -#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) #define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_TIMESTAMP /* Print image info with ts */ - +#define CONFIG_TIMESTAMP /* Print image info with ts */ /* * BOOTP options @@ -372,6 +579,25 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME +#ifdef CONFIG_NAND +/* + * Use NAND-FLash as JFFS2 device + */ +#define CONFIG_CMD_NAND +#define CONFIG_CMD_JFFS2 + +#define CONFIG_JFFS2_NAND 1 + +#ifdef CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nand0=TQM85xx-nand" +#define MTDPARTS_DEFAULT "mtdparts=TQM85xx-nand:-" +#else +#define CONFIG_JFFS2_DEV "nand0" /* NAND device jffs2 lives on */ +#define CONFIG_JFFS2_PART_OFFSET 0 /* start of jffs2 partition */ +#define CONFIG_JFFS2_PART_SIZE 0x200000 /* size of jffs2 partition */ +#endif /* CONFIG_JFFS2_CMDLINE */ + +#endif /* CONFIG_NAND */ /* * Command line configuration. @@ -389,10 +615,9 @@ #define CONFIG_CMD_MII #if defined(CONFIG_PCI) - #define CONFIG_CMD_PCI +#define CONFIG_CMD_PCI #endif - #undef CONFIG_WATCHDOG /* watchdog disabled */ /* @@ -403,12 +628,13 @@ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buf Size */ +#define CFG_PBSIZE (CFG_CBSIZE + \ + sizeof(CFG_PROMPT) + 16) /* Print Buf Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ @@ -433,7 +659,6 @@ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif - #define CONFIG_LOADADDR 200000 /* default addr for tftp & bootm*/ #define CONFIG_BOOTDELAY 5 /* -1 disables auto-boot */ @@ -444,10 +669,26 @@ #undef CONFIG_BOOTARGS /* the boot command will set bootargs */ + +/* + * Setup some board specific values for the default environment variables + */ +#ifdef CONFIG_CPM2 +#define CFG_ENV_CONSDEV "consdev=ttyCPM0\0" +#else +#define CFG_ENV_CONSDEV "consdev=ttyS0\0" +#endif +#define CFG_ENV_FDT_FILE "fdt_file="MK_STR(CONFIG_HOSTNAME)"/" \ + MK_STR(CONFIG_HOSTNAME)".dtb\0" +#define CFG_ENV_BOOTFILE "bootfile="MK_STR(CONFIG_HOSTNAME)"/uImage\0" +#define CFG_ENV_UBOOT "uboot="MK_STR(CONFIG_HOSTNAME)"/u-boot.bin\0" \ + "uboot_addr="MK_STR(TEXT_BASE)"\0" + #define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile="CFG_BOOTFILE_PATH"\0" \ + CFG_ENV_BOOTFILE \ + CFG_ENV_FDT_FILE \ + CFG_ENV_CONSDEV \ "netdev=eth0\0" \ - "consdev=ttyS0\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=$serverip:$rootpath\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -457,20 +698,27 @@ "addcons=setenv bootargs $bootargs " \ "console=$consdev,$baudrate\0" \ "flash_nfs=run nfsargs addip addcons;" \ - "bootm $kernel_addr\0" \ + "bootm $kernel_addr - $fdt_addr\0" \ "flash_self=run ramargs addip addcons;" \ - "bootm $kernel_addr $ramdisk_addr\0" \ - "net_nfs=tftp $loadaddr $bootfile;" \ - "run nfsargs addip addcons;bootm\0" \ + "bootm $kernel_addr $ramdisk_addr $fdt_addr\0" \ + "net_nfs=tftp $kernel_addr_r $bootfile;" \ + "tftp $fdt_addr_r $fdt_file;" \ + "run nfsargs addip addcons;" \ + "bootm $kernel_addr_r - $fdt_addr_r\0" \ "rootpath=/opt/eldk/ppc_85xx\0" \ - "kernel_addr=FE000000\0" \ - "ramdisk_addr=FE180000\0" \ - "load=tftp 100000 /tftpboot/$hostname/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ + "fdt_addr_r=900000\0" \ + "kernel_addr_r=1000000\0" \ + "fdt_addr=ffec0000\0" \ + "kernel_addr=ffd00000\0" \ + "ramdisk_addr=ff800000\0" \ + CFG_ENV_UBOOT \ + "load=tftp 100000 $uboot\0" \ + "update=protect off $uboot_addr +$filesize;" \ + "erase $uboot_addr +$filesize;" \ + "cp.b 100000 $uboot_addr $filesize;" \ "setenv filesize;saveenv\0" \ "upd=run load update\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" -#endif /* __CONFIG_H */ +#endif /* __CONFIG_H */ diff --git a/include/configs/Total5200.h b/include/configs/Total5200.h index 31f10dd..598fe7b 100644 --- a/include/configs/Total5200.h +++ b/include/configs/Total5200.h @@ -48,6 +48,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/Yukon8220.h b/include/configs/Yukon8220.h index 00c4ff0..1b4195a 100644 --- a/include/configs/Yukon8220.h +++ b/include/configs/Yukon8220.h @@ -31,6 +31,8 @@ #define CONFIG_MPC8220 1 #define CONFIG_YUKON8220 1 /* ... on Yukon board */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* Input clock running at 30Mhz, read Hid1 for the CPU multiplier to determine the CPU speed. */ #define CFG_MPC8220_CLKIN 30000000/* ... running at 30MHz */ diff --git a/include/configs/acadia.h b/include/configs/acadia.h index bbf726d..9092a7c 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -34,6 +34,13 @@ #define CONFIG_ACADIA 1 /* Board is Acadia */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405EZ 1 /* Specifc 405EZ support*/ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME acadia +#include "amcc-common.h" + /* Detect Acadia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \ 66666666 : 33333000) @@ -59,16 +66,11 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xfe000000 #define CFG_CPLD_BASE 0x80000000 #define CFG_NAND_ADDR 0xd0000000 #define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ @@ -89,12 +91,6 @@ *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #define CFG_BASE_BAUD 691200 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 - -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Environment @@ -202,10 +198,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -222,77 +215,24 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#if 0 /* test-only... */ -/*----------------------------------------------------------------------- - * SPI stuff - Define to include SPI control - *----------------------------------------------------------------------- - */ -#define CONFIG_SPI -#endif - /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=acadia\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=acadia/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 acadia/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 acadia/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "kozio=bootm ffc60000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE @@ -305,35 +245,10 @@ #define CONFIG_SUPPORT_VFAT /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_USB /* @@ -344,43 +259,6 @@ #undef CONFIG_CMD_IMLS #endif -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -493,21 +371,4 @@ #define CFG_GPIO1_TSRL 0x00000000 #define CFG_GPIO1_TSRH 0x00000000 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ - #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h index c975a24..4226529 100644 --- a/include/configs/ads5121.h +++ b/include/configs/ads5121.h @@ -372,6 +372,8 @@ #define CFG_HID0_FINAL HID0_ENABLE_MACHINE_CHECK #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Internal Definitions * diff --git a/include/configs/aev.h b/include/configs/aev.h index e3f810c..c5e4759 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -41,6 +41,8 @@ #define CONFIG_AEVFIFO 1 #define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ diff --git a/include/configs/alpr.h b/include/configs/alpr.h index 3e906c4..fb6feb5 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -33,7 +33,6 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define CONFIG_4xx_DCACHE /* Enable i- and d-cache */ diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h new file mode 100644 index 0000000..1f27d78 --- /dev/null +++ b/include/configs/amcc-common.h @@ -0,0 +1,259 @@ +/* + * (C) Copyright 2008 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * Common configuration options for all AMCC boards + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __AMCC_COMMON_H +#define __AMCC_COMMON_H + +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ +#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) +#define CFG_MALLOC_LEN (1 << 20) /* Reserved for malloc */ + +/* + * UART + */ +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/* + * I2C + */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CFG_I2C_SLAVE 0x7F + +/* + * Ethernet/EMAC/PHY + */ +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_NET_MULTI +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#if defined(CONFIG_440) +#define CFG_RX_ETH_BUFFER 32 /* number of eth rx buffers */ +#else +#define CFG_RX_ETH_BUFFER 16 /* number of eth rx buffers */ +#endif + +/* + * Commands + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#if defined(CONFIG_440) +#define CONFIG_CMD_CACHE +#endif +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +/* + * Miscellaneous configurable options + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING /* add command line history */ +#define CONFIG_AUTO_COMPLETE /* add autocompletion support */ +#define CONFIG_LOOPW /* enable loopw command */ +#define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE /* include version env variable */ +#define CFG_CONSOLE_INFO_QUIET /* don't print console @ startup*/ + +#define CFG_HUSH_PARSER /* Use the HUSH parser */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME +#define CONFIG_BOOTP_SUBNETMASK + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Internal Definitions + */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP + +/* + * Booting and default environment + */ +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" +#define CONFIG_BOOTCOMMAND "run flash_self" + +/* + * Only very few boards have default console not on ttyS0 (like Taishan) + */ +#if !defined(CONFIG_USE_TTY) +#define CONFIG_USE_TTY ttyS0 +#endif + +/* + * Only some 4xx PPC's are equipped with an FPU + */ +#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ + defined(CONFIG_460EX) || defined(CONFIG_460GT) +#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" +#else +#define CONFIG_AMCC_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" +#endif + +/* + * Only some boards need to extend the bootargs by some additional + * parameters (like Makalu) + */ +#if !defined(CONFIG_ADDMISC) +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0" +#endif + +#define xstr(s) str(s) +#define str(s) #s + +/* + * General common environment variables shared on all AMCC eval boards + */ +#define CONFIG_AMCC_DEF_ENV \ + "netdev=eth0\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs}" \ + " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \ + CONFIG_ADDMISC \ + "initrd_high=30000000\0" \ + "kernel_addr_r=400000\0" \ + "fdt_addr_r=800000\0" \ + "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ + "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ + CONFIG_AMCC_DEF_ENV_ROOTPATH + +/* + * Default environment for arch/powerpc booting + * for boards that are ported to arch/powerpc + */ +#define CONFIG_AMCC_DEF_ENV_POWERPC \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr} - ${fdt_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ + "tftp ${fdt_addr_r} ${fdt_file}; " \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ + "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" + +/* + * Default environment for arch/ppc booting, + * for boards that are not ported to arch/powerpc yet + */ +#define CONFIG_AMCC_DEF_ENV_PPC \ + "flash_self=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r}\0" + +/* + * Default environment for arch/ppc booting (old version), + * for boards that are ported to arch/ppc and arch/powerpc + */ +#define CONFIG_AMCC_DEF_ENV_PPC_OLD \ + "flash_self_old=run ramargs addip addtty addmisc;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs_old=run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ + "run nfsargs addip addtty addmisc;" \ + "bootm ${kernel_addr_r}\0" + +#define CONFIG_AMCC_DEF_ENV_NOR_UPD \ + "load=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ + "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ + "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ + "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load update\0" \ + +#define CONFIG_AMCC_DEF_ENV_NAND_UPD \ + "nload=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot-nand.bin\0" \ + "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ + "setenv filesize;saveenv\0" \ + "nupd=run nload nupdate\0" + +#endif /* __AMCC_COMMON_H */ diff --git a/include/configs/at91cap9adk.h b/include/configs/at91cap9adk.h index c891fa8..342ce2a 100644 --- a/include/configs/at91cap9adk.h +++ b/include/configs/at91cap9adk.h @@ -28,6 +28,7 @@ #define __CONFIG_H /* ARM asynchronous clock */ +#define AT91_CPU_NAME "AT91CAP9" #define AT91_MAIN_CLOCK 200000000 /* from 12 MHz crystal */ #define AT91_MASTER_CLOCK 100000000 /* peripheral = main / 2 */ #define CFG_HZ 1000000 /* 1us resolution */ @@ -55,11 +56,19 @@ #undef CONFIG_USART2 #define CONFIG_USART3 1 /* USART 3 is DBGU */ -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ - "root=/dev/mtdblock1 rw rootfstype=jffs2" +/* LCD */ +#define CONFIG_LCD 1 +#define LCD_BPP LCD_COLOR8 +#define CONFIG_LCD_LOGO 1 +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO 1 +#define CONFIG_LCD_INFO_BELOW_LOGO 1 +#define CFG_WHITE_ON_BLACK 1 +#define CONFIG_ATMEL_LCD 1 +#define CONFIG_ATMEL_LCD_BGR555 1 +#define CFG_CONSOLE_IS_IN_ENV 1 -/* #define CONFIG_ENV_OVERWRITE 1 */ +#define CONFIG_BOOTDELAY 3 /* * BOOTP options @@ -94,9 +103,9 @@ #define CFG_SPI_WRITE_TOUT (5*CFG_HZ) #define CFG_MAX_DATAFLASH_BANKS 1 #define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ -#define AT91_SPI_CLK 20000000 -#define DATAFLASH_TCSS (0xFA << 16) -#define DATAFLASH_TCHS (0x8 << 24) +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) /* NOR flash */ #define CFG_FLASH_CFI 1 @@ -110,6 +119,7 @@ #define NAND_MAX_CHIPS 1 #define CFG_MAX_NAND_DEVICE 1 #define CFG_NAND_BASE 0x40000000 +#define CFG_NAND_DBW_8 1 /* Ethernet */ #define CONFIG_MACB 1 @@ -143,7 +153,12 @@ #define CFG_ENV_OFFSET 0x4200 #define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CFG_ENV_OFFSET) #define CFG_ENV_SIZE 0x4200 -#define CONFIG_BOOTCOMMAND "cp.b 0xC003DE00 0x72000000 0x200040; bootm" +#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x72000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock1 " \ + "mtdparts=physmap-flash.0:-(nor);" \ + "at91_nand:-(root) " \ + "rw rootfstype=jffs2" #else @@ -154,6 +169,12 @@ #define CFG_ENV_ADDR (PHYS_FLASH_1 + CFG_ENV_OFFSET) #define CFG_ENV_SIZE 0x4000 #define CONFIG_BOOTCOMMAND "cp.b 0x10040000 0x72000000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock4 " \ + "mtdparts=physmap-flash.0:16k(bootstrap)ro,"\ + "16k(env),224k(uboot)ro,-(linux);" \ + "at91_nand:-(root) " \ + "rw rootfstype=jffs2" #endif diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h index 41c418f..675224e 100644 --- a/include/configs/at91sam9260ek.h +++ b/include/configs/at91sam9260ek.h @@ -56,10 +56,6 @@ #define CONFIG_USART3 1 /* USART 3 is DBGU */ #define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ - "root=/dev/mtdblock0 rw rootfstype=jffs2" - -/* #define CONFIG_ENV_OVERWRITE 1 */ /* * BOOTP options @@ -96,7 +92,7 @@ #define CFG_MAX_DATAFLASH_BANKS 2 #define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ #define CFG_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */ -#define AT91_SPI_CLK 33000000 +#define AT91_SPI_CLK 15000000 #define DATAFLASH_TCSS (0x1a << 16) #define DATAFLASH_TCHS (0x1 << 24) @@ -104,6 +100,7 @@ #define NAND_MAX_CHIPS 1 #define CFG_MAX_NAND_DEVICE 1 #define CFG_NAND_BASE 0x40000000 +#define CFG_NAND_DBW_8 1 /* NOR flash - no real flash on this board */ #define CFG_NO_FLASH 1 @@ -142,7 +139,11 @@ #define CFG_ENV_OFFSET 0x4200 #define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CFG_ENV_OFFSET) #define CFG_ENV_SIZE 0x4200 -#define CONFIG_BOOTCOMMAND "cp.b 0xC003DE00 0x22000000 0x200040; bootm" +#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=at91_nand:-(root) " \ + "rw rootfstype=jffs2" #elif CFG_USE_DATAFLASH_CS1 @@ -152,7 +153,11 @@ #define CFG_ENV_OFFSET 0x4200 #define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS1 + CFG_ENV_OFFSET) #define CFG_ENV_SIZE 0x4200 -#define CONFIG_BOOTCOMMAND "cp.b 0xD003DE00 0x22000000 0x200040; bootm" +#define CONFIG_BOOTCOMMAND "cp.b 0xD0042000 0x22000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=at91_nand:-(root) " \ + "rw rootfstype=jffs2" #else /* CFG_USE_NANDFLASH */ @@ -162,6 +167,12 @@ #define CFG_ENV_OFFSET_REDUND 0x80000 #define CFG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ #define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock5 " \ + "mtdparts=at91_nand:128k(bootstrap)ro," \ + "256k(uboot)ro,128k(env1)ro," \ + "128k(env2)ro,2M(linux),-(root) " \ + "rw rootfstype=jffs2" #endif diff --git a/include/configs/at91sam9261ek.h b/include/configs/at91sam9261ek.h new file mode 100644 index 0000000..e53a23f --- /dev/null +++ b/include/configs/at91sam9261ek.h @@ -0,0 +1,202 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian.pop@leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * + * Configuation settings for the AT91SAM9261EK board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* ARM asynchronous clock */ +#define AT91_CPU_NAME "AT91SAM9261" +#define AT91_MAIN_CLOCK 198656000 /* from 18.432 MHz crystal */ +#define AT91_MASTER_CLOCK 99328000 /* peripheral = main / 2 */ +#define CFG_HZ 1000000 /* 1us resolution */ + +#define AT91_SLOW_CLOCK 32768 /* slow clock */ + +#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ +#define CONFIG_AT91SAM9261 1 /* It's an Atmel AT91SAM9261 SoC*/ +#define CONFIG_AT91SAM9261EK 1 /* on an AT91SAM9261EK Board */ +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT + +/* + * Hardware drivers + */ +#define CONFIG_ATMEL_USART 1 +#undef CONFIG_USART0 +#undef CONFIG_USART1 +#undef CONFIG_USART2 +#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +/* LCD */ +#define CONFIG_LCD 1 +#define LCD_BPP LCD_COLOR8 +#define CONFIG_LCD_LOGO 1 +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO 1 +#define CONFIG_LCD_INFO_BELOW_LOGO 1 +#define CFG_WHITE_ON_BLACK 1 +#define CONFIG_ATMEL_LCD 1 +#define CONFIG_ATMEL_LCD_BGR555 1 +#define CFG_CONSOLE_IS_IN_ENV 1 + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE 1 +#define CONFIG_BOOTP_BOOTPATH 1 +#define CONFIG_BOOTP_GATEWAY 1 +#define CONFIG_BOOTP_HOSTNAME 1 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_IMLS + +#define CONFIG_CMD_PING 1 +#define CONFIG_CMD_DHCP 1 +#define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_USB 1 + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x20000000 +#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ + +/* DataFlash */ +#define CONFIG_HAS_DATAFLASH 1 +#define CFG_SPI_WRITE_TOUT (5*CFG_HZ) +#define CFG_MAX_DATAFLASH_BANKS 2 +#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ +#define CFG_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* CS3 */ +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) + +/* NAND flash */ +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE 0x40000000 +#define CFG_NAND_DBW_8 1 + +/* NOR flash - no real flash on this board */ +#define CFG_NO_FLASH 1 + +/* Ethernet */ +#define CONFIG_DRIVER_DM9000 1 +#define CONFIG_DM9000_BASE 0x30000000 +#define DM9000_IO CONFIG_DM9000_BASE +#define DM9000_DATA (CONFIG_DM9000_BASE + 4) +#define CONFIG_DM9000_USE_16BIT 1 +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_RESET_PHY_R 1 + +/* USB */ +#define CONFIG_USB_OHCI_NEW 1 +#define LITTLEENDIAN 1 +#define CONFIG_DOS_PARTITION 1 +#define CFG_USB_OHCI_CPU_INIT 1 +#define CFG_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9261_UHP_BASE */ +#define CFG_USB_OHCI_SLOT_NAME "at91sam9261" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE 1 + +#define CFG_LOAD_ADDR 0x22000000 /* load address */ + +#define CFG_MEMTEST_START PHYS_SDRAM +#define CFG_MEMTEST_END 0x23e00000 + +#define CFG_USE_DATAFLASH_CS0 1 +#undef CFG_USE_NANDFLASH + +#ifdef CFG_USE_DATAFLASH_CS0 + +/* bootstrap + u-boot + env + linux in dataflash on CS0 */ +#define CFG_ENV_IS_IN_DATAFLASH 1 +#define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) +#define CFG_ENV_OFFSET 0x4200 +#define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CFG_ENV_OFFSET) +#define CFG_ENV_SIZE 0x4200 +#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=at91_nand:-(root) " \ + "rw rootfstype=jffs2" + +#else /* CFG_USE_NANDFLASH */ + +/* bootstrap + u-boot + env + linux in nandflash */ +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x60000 +#define CFG_ENV_OFFSET_REDUND 0x80000 +#define CFG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock5 " \ + "mtdparts=at91_nand:128k(bootstrap)ro," \ + "256k(uboot)ro,128k(env1)ro," \ + "128k(env2)ro,2M(linux),-(root) " \ + "rw rootfstype=jffs2" + +#endif + +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +#define CFG_PROMPT "U-Boot> " +#define CFG_CBSIZE 256 +#define CFG_MAXARGS 16 +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 + +#define ROUND(A, B) (((A) + (B)) & ~((B) - 1)) +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN ROUND(3 * CFG_ENV_SIZE + 128*1024, 0x1000) +#define CFG_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ + +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h new file mode 100644 index 0000000..a8194b5 --- /dev/null +++ b/include/configs/at91sam9263ek.h @@ -0,0 +1,206 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian.pop@leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * + * Configuation settings for the AT91SAM9263EK board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* ARM asynchronous clock */ +#define AT91_CPU_NAME "AT91SAM9263" +#define AT91_MAIN_CLOCK 199919000 /* from 16.367 MHz crystal */ +#define AT91_MASTER_CLOCK 99959500 /* peripheral = main / 2 */ +#define CFG_HZ 1000000 /* 1us resolution */ + +#define AT91_SLOW_CLOCK 32768 /* slow clock */ + +#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ +#define CONFIG_AT91SAM9263 1 /* It's an Atmel AT91SAM9263 SoC*/ +#define CONFIG_AT91SAM9263EK 1 /* on an AT91SAM9263EK Board */ +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT + +/* + * Hardware drivers + */ +#define CONFIG_ATMEL_USART 1 +#undef CONFIG_USART0 +#undef CONFIG_USART1 +#undef CONFIG_USART2 +#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +/* LCD */ +#define CONFIG_LCD 1 +#define LCD_BPP LCD_COLOR8 +#define CONFIG_LCD_LOGO 1 +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO 1 +#define CONFIG_LCD_INFO_BELOW_LOGO 1 +#define CFG_WHITE_ON_BLACK 1 +#define CONFIG_ATMEL_LCD 1 +#define CONFIG_ATMEL_LCD_BGR555 1 +#define CFG_CONSOLE_IS_IN_ENV 1 + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE 1 +#define CONFIG_BOOTP_BOOTPATH 1 +#define CONFIG_BOOTP_GATEWAY 1 +#define CONFIG_BOOTP_HOSTNAME 1 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_IMLS + +#define CONFIG_CMD_PING 1 +#define CONFIG_CMD_DHCP 1 +#define CONFIG_CMD_NAND 1 +#define CONFIG_CMD_USB 1 + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x20000000 +#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ + +/* DataFlash */ +#define CONFIG_HAS_DATAFLASH 1 +#define CFG_SPI_WRITE_TOUT (5*CFG_HZ) +#define CFG_MAX_DATAFLASH_BANKS 1 +#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) + +/* NOR flash, if populated */ +#if 1 +#define CFG_NO_FLASH 1 +#else +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_CFI_DRIVER 1 +#define PHYS_FLASH_1 0x10000000 +#define CFG_FLASH_BASE PHYS_FLASH_1 +#define CFG_MAX_FLASH_SECT 256 +#define CFG_MAX_FLASH_BANKS 1 +#endif + +/* NAND flash */ +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE 0x40000000 +#define CFG_NAND_DBW_8 1 + +/* Ethernet */ +#define CONFIG_MACB 1 +#define CONFIG_RMII 1 +#define CONFIG_NET_MULTI 1 +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_RESET_PHY_R 1 + +/* USB */ +#define CONFIG_USB_OHCI_NEW 1 +#define LITTLEENDIAN 1 +#define CONFIG_DOS_PARTITION 1 +#define CFG_USB_OHCI_CPU_INIT 1 +#define CFG_USB_OHCI_REGS_BASE 0x00a00000 /* AT91SAM9263_UHP_BASE */ +#define CFG_USB_OHCI_SLOT_NAME "at91sam9263" +#define CFG_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE 1 + +#define CFG_LOAD_ADDR 0x22000000 /* load address */ + +#define CFG_MEMTEST_START PHYS_SDRAM +#define CFG_MEMTEST_END 0x23e00000 + +#define CFG_USE_DATAFLASH 1 +#undef CFG_USE_NANDFLASH + +#ifdef CFG_USE_DATAFLASH + +/* bootstrap + u-boot + env + linux in dataflash on CS0 */ +#define CFG_ENV_IS_IN_DATAFLASH 1 +#define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) +#define CFG_ENV_OFFSET 0x4200 +#define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CFG_ENV_OFFSET) +#define CFG_ENV_SIZE 0x4200 +#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=at91_nand:-(root) "\ + "rw rootfstype=jffs2" + +#else /* CFG_USE_NANDFLASH */ + +/* bootstrap + u-boot + env + linux in nandflash */ +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x60000 +#define CFG_ENV_OFFSET_REDUND 0x80000 +#define CFG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock5 " \ + "mtdparts=at91_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) " \ + "rw rootfstype=jffs2" + +#endif + +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +#define CFG_PROMPT "U-Boot> " +#define CFG_CBSIZE 256 +#define CFG_MAXARGS 16 +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 + +#define ROUND(A, B) (((A) + (B)) & ~((B) - 1)) +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN ROUND(3 * CFG_ENV_SIZE + 128*1024, 0x1000) +#define CFG_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ + +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif diff --git a/include/configs/at91sam9rlek.h b/include/configs/at91sam9rlek.h new file mode 100644 index 0000000..2ad8d05 --- /dev/null +++ b/include/configs/at91sam9rlek.h @@ -0,0 +1,175 @@ +/* + * (C) Copyright 2007-2008 + * Stelian Pop <stelian.pop@leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * + * Configuation settings for the AT91SAM9RLEK board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* ARM asynchronous clock */ +#define AT91_CPU_NAME "AT91SAM9RL" +#define AT91_MAIN_CLOCK 200000000 /* from 12.000 MHz crystal */ +#define AT91_MASTER_CLOCK 100000000 /* peripheral = main / 2 */ +#define CFG_HZ 1000000 /* 1us resolution */ + +#define AT91_SLOW_CLOCK 32768 /* slow clock */ + +#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */ +#define CONFIG_AT91SAM9RL 1 /* It's an Atmel AT91SAM9RL SoC*/ +#define CONFIG_AT91SAM9RLEK 1 /* on an AT91SAM9RLEK Board */ +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_SKIP_RELOCATE_UBOOT + +/* + * Hardware drivers + */ +#define CONFIG_ATMEL_USART 1 +#undef CONFIG_USART0 +#undef CONFIG_USART1 +#undef CONFIG_USART2 +#define CONFIG_USART3 1 /* USART 3 is DBGU */ + +/* LCD */ +#define CONFIG_LCD 1 +#define LCD_BPP LCD_COLOR8 +#define CONFIG_LCD_LOGO 1 +#undef LCD_TEST_PATTERN +#define CONFIG_LCD_INFO 1 +#define CONFIG_LCD_INFO_BELOW_LOGO 1 +#define CFG_WHITE_ON_BLACK 1 +#define CONFIG_ATMEL_LCD 1 +#define CONFIG_ATMEL_LCD_RGB565 1 +#define CFG_CONSOLE_IS_IN_ENV 1 + +#define CONFIG_BOOTDELAY 3 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_USB + +#define CONFIG_CMD_NAND 1 + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM 0x20000000 +#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */ + +/* DataFlash */ +#define CONFIG_HAS_DATAFLASH 1 +#define CFG_SPI_WRITE_TOUT (5*CFG_HZ) +#define CFG_MAX_DATAFLASH_BANKS 1 +#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* CS0 */ +#define AT91_SPI_CLK 15000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) + +/* NOR flash - not present */ +#define CFG_NO_FLASH 1 + +/* NAND flash */ +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#define CFG_NAND_BASE 0x40000000 +#define CFG_NAND_DBW_8 1 + +/* Ethernet - not present */ + +/* USB - not supported */ + +#define CFG_LOAD_ADDR 0x22000000 /* load address */ + +#define CFG_MEMTEST_START PHYS_SDRAM +#define CFG_MEMTEST_END 0x23e00000 + +#define CFG_USE_DATAFLASH 1 +#undef CFG_USE_NANDFLASH + +#ifdef CFG_USE_DATAFLASH + +/* bootstrap + u-boot + env + linux in dataflash on CS0 */ +#define CFG_ENV_IS_IN_DATAFLASH 1 +#define CFG_MONITOR_BASE (CFG_DATAFLASH_LOGIC_ADDR_CS0 + 0x8400) +#define CFG_ENV_OFFSET 0x4200 +#define CFG_ENV_ADDR (CFG_DATAFLASH_LOGIC_ADDR_CS0 + CFG_ENV_OFFSET) +#define CFG_ENV_SIZE 0x4200 +#define CONFIG_BOOTCOMMAND "cp.b 0xC0042000 0x22000000 0x210000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock0 " \ + "mtdparts=at91_nand:-(root) "\ + "rw rootfstype=jffs2" + +#else /* CFG_USE_NANDFLASH */ + +/* bootstrap + u-boot + env + linux in nandflash */ +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x60000 +#define CFG_ENV_OFFSET_REDUND 0x80000 +#define CFG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0xA0000 0x200000; bootm" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock5 " \ + "mtdparts=at91_nand:128k(bootstrap)ro,256k(uboot)ro,128k(env1)ro,128k(env2)ro,2M(linux),-(root) " \ + "rw rootfstype=jffs2" + +#endif + +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 } + +#define CFG_PROMPT "U-Boot> " +#define CFG_CBSIZE 256 +#define CFG_MAXARGS 16 +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 + +#define ROUND(A, B) (((A) + (B)) & ~((B) - 1)) +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN ROUND(3 * CFG_ENV_SIZE + 128*1024, 0x1000) +#define CFG_GBL_DATA_SIZE 128 /* 128 bytes for initial data */ + +#define CONFIG_STACKSIZE (32*1024) /* regular stack */ + +#ifdef CONFIG_USE_IRQ +#error CONFIG_USE_IRQ not supported +#endif + +#endif diff --git a/include/configs/atngw100.h b/include/configs/atngw100.h index 5aad043..84d235e 100644 --- a/include/configs/atngw100.h +++ b/include/configs/atngw100.h @@ -24,6 +24,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include <asm/arch/memory-map.h> + #define CONFIG_AVR32 1 #define CONFIG_AT32AP 1 #define CONFIG_AT32AP7000 1 @@ -112,8 +114,13 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_MMC +#define CONFIG_CMD_SF +#define CONFIG_CMD_SPI + +#undef CONFIG_CMD_AUTOSCRIPT #undef CONFIG_CMD_FPGA #undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG #define CONFIG_ATMEL_USART 1 #define CONFIG_MACB 1 @@ -121,6 +128,11 @@ #define CFG_NR_PIOS 5 #define CFG_HSDRAMC 1 #define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 +#define CONFIG_ATMEL_SPI 1 + +#define CONFIG_SPI_FLASH 1 +#define CONFIG_SPI_FLASH_ATMEL 1 #define CFG_DCACHE_LINESZ 32 #define CFG_ICACHE_LINESZ 32 @@ -137,11 +149,9 @@ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_INTRAM_BASE 0x24000000 -#define CFG_INTRAM_SIZE 0x8000 - -#define CFG_SDRAM_BASE 0x10000000 -#define CFG_SDRAM_16BIT 1 +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 65536 @@ -150,27 +160,20 @@ #define CFG_INIT_SP_ADDR (CFG_INTRAM_BASE + CFG_INTRAM_SIZE) #define CFG_MALLOC_LEN (256*1024) -#define CFG_MALLOC_END \ - ({ \ - DECLARE_GLOBAL_DATA_PTR; \ - CFG_SDRAM_BASE + gd->sdram_size; \ - }) -#define CFG_MALLOC_START (CFG_MALLOC_END - CFG_MALLOC_LEN) - #define CFG_DMA_ALLOC_LEN (16384) /* Allow 4MB for the kernel run-time image */ -#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00400000) +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) #define CFG_BOOTPARAMS_LEN (16 * 1024) /* Other configuration settings that shouldn't have to change all that often */ -#define CFG_PROMPT "Uboot> " +#define CFG_PROMPT "U-Boot> " #define CFG_CBSIZE 256 #define CFG_MAXARGS 16 #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_LONGHELP 1 -#define CFG_MEMTEST_START CFG_SDRAM_BASE +#define CFG_MEMTEST_START EBI_SDRAM_BASE #define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x1f00000) #define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h index 95aeab6..90910bb 100644 --- a/include/configs/atstk1002.h +++ b/include/configs/atstk1002.h @@ -24,6 +24,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include <asm/arch/memory-map.h> + #define CONFIG_AVR32 1 #define CONFIG_AT32AP 1 #define CONFIG_AT32AP7000 1 @@ -139,9 +141,9 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_MMC -#define CONFIG_CMD_REGINFO #undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA #undef CONFIG_CMD_SETGETDCR #undef CONFIG_CMD_XIMG @@ -151,6 +153,7 @@ #define CFG_NR_PIOS 5 #define CFG_HSDRAMC 1 #define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 #define CFG_DCACHE_LINESZ 32 #define CFG_ICACHE_LINESZ 32 @@ -170,10 +173,9 @@ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_INTRAM_BASE 0x24000000 -#define CFG_INTRAM_SIZE 0x8000 - -#define CFG_SDRAM_BASE 0x10000000 +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 65536 @@ -185,17 +187,17 @@ #define CFG_DMA_ALLOC_LEN (16384) /* Allow 4MB for the kernel run-time image */ -#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00400000) +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) #define CFG_BOOTPARAMS_LEN (16 * 1024) /* Other configuration settings that shouldn't have to change all that often */ -#define CFG_PROMPT "Uboot> " +#define CFG_PROMPT "U-Boot> " #define CFG_CBSIZE 256 -#define CFG_MAXARGS 8 +#define CFG_MAXARGS 16 #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_LONGHELP 1 -#define CFG_MEMTEST_START CFG_SDRAM_BASE +#define CFG_MEMTEST_START EBI_SDRAM_BASE #define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x700000) #define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } diff --git a/include/configs/atstk1003.h b/include/configs/atstk1003.h index 194788b..03472a8 100644 --- a/include/configs/atstk1003.h +++ b/include/configs/atstk1003.h @@ -24,6 +24,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include <asm/arch/memory-map.h> + #define CONFIG_AVR32 1 #define CONFIG_AT32AP 1 #define CONFIG_AT32AP7001 1 @@ -134,6 +136,7 @@ #define CONFIG_PIO2 1 #define CFG_HSDRAMC 1 #define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 #define CFG_DCACHE_LINESZ 32 #define CFG_ICACHE_LINESZ 32 @@ -153,10 +156,9 @@ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_INTRAM_BASE 0x24000000 -#define CFG_INTRAM_SIZE 0x8000 - -#define CFG_SDRAM_BASE 0x10000000 +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 65536 @@ -167,17 +169,17 @@ #define CFG_MALLOC_LEN (256*1024) /* Allow 4MB for the kernel run-time image */ -#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00400000) +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) #define CFG_BOOTPARAMS_LEN (16 * 1024) /* Other configuration settings that shouldn't have to change all that often */ -#define CFG_PROMPT "Uboot> " +#define CFG_PROMPT "U-Boot> " #define CFG_CBSIZE 256 #define CFG_MAXARGS 16 #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_LONGHELP 1 -#define CFG_MEMTEST_START CFG_SDRAM_BASE +#define CFG_MEMTEST_START EBI_SDRAM_BASE #define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x700000) #define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } diff --git a/include/configs/atstk1004.h b/include/configs/atstk1004.h index b81fc21..07add82 100644 --- a/include/configs/atstk1004.h +++ b/include/configs/atstk1004.h @@ -24,6 +24,8 @@ #ifndef __CONFIG_H #define __CONFIG_H +#include <asm/arch/memory-map.h> + #define CONFIG_AVR32 1 #define CONFIG_AT32AP 1 #define CONFIG_AT32AP7002 1 @@ -134,6 +136,7 @@ #define CONFIG_PIO2 1 #define CFG_HSDRAMC 1 #define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 #define CFG_DCACHE_LINESZ 32 #define CFG_ICACHE_LINESZ 32 @@ -153,11 +156,9 @@ #define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_INTRAM_BASE 0x24000000 -#define CFG_INTRAM_SIZE 0x8000 - -#define CFG_SDRAM_BASE 0x10000000 -#define CFG_SDRAM_16BIT 1 +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_SIZE 65536 @@ -168,17 +169,17 @@ #define CFG_MALLOC_LEN (256*1024) /* Allow 2MB for the kernel run-time image */ -#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 0x00200000) +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00200000) #define CFG_BOOTPARAMS_LEN (16 * 1024) /* Other configuration settings that shouldn't have to change all that often */ -#define CFG_PROMPT "Uboot> " +#define CFG_PROMPT "U-Boot> " #define CFG_CBSIZE 256 #define CFG_MAXARGS 16 #define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) #define CFG_LONGHELP 1 -#define CFG_MEMTEST_START CFG_SDRAM_BASE +#define CFG_MEMTEST_START EBI_SDRAM_BASE #define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x700000) #define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } diff --git a/include/configs/atstk1006.h b/include/configs/atstk1006.h new file mode 100644 index 0000000..f9af675 --- /dev/null +++ b/include/configs/atstk1006.h @@ -0,0 +1,204 @@ +/* + * Copyright (C) 2005-2006 Atmel Corporation + * + * Configuration settings for the ATSTK1002 CPU daughterboard + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/memory-map.h> + +#define CONFIG_AVR32 1 +#define CONFIG_AT32AP 1 +#define CONFIG_AT32AP7000 1 +#define CONFIG_ATSTK1006 1 +#define CONFIG_ATSTK1000 1 + +#define CONFIG_ATSTK1000_EXT_FLASH 1 + +/* + * Timer clock frequency. We're using the CPU-internal COUNT register + * for this, so this is equivalent to the CPU core clock frequency + */ +#define CFG_HZ 1000 + +/* + * Set up the PLL to run at 140 MHz, the CPU to run at the PLL + * frequency, the HSB and PBB at 1/2, and the PBA to run at 1/4 the + * PLL frequency. + * (CFG_OSC0_HZ * CFG_PLL0_MUL) / CFG_PLL0_DIV = PLL MHz + */ +#define CONFIG_PLL 1 +#define CFG_POWER_MANAGER 1 +#define CFG_OSC0_HZ 20000000 +#define CFG_PLL0_DIV 1 +#define CFG_PLL0_MUL 7 +#define CFG_PLL0_SUPPRESS_CYCLES 16 +/* + * Set the CPU running at: + * PLL / (2^CFG_CLKDIV_CPU) = CPU MHz + */ +#define CFG_CLKDIV_CPU 0 +/* + * Set the HSB running at: + * PLL / (2^CFG_CLKDIV_HSB) = HSB MHz + */ +#define CFG_CLKDIV_HSB 1 +/* + * Set the PBA running at: + * PLL / (2^CFG_CLKDIV_PBA) = PBA MHz + */ +#define CFG_CLKDIV_PBA 2 +/* + * Set the PBB running at: + * PLL / (2^CFG_CLKDIV_PBB) = PBB MHz + */ +#define CFG_CLKDIV_PBB 1 + +/* + * The PLLOPT register controls the PLL like this: + * icp = PLLOPT<2> + * ivco = PLLOPT<1:0> + * + * We want icp=1 (default) and ivco=0 (80-160 MHz) or ivco=2 (150-240MHz). + */ +#define CFG_PLL0_OPT 0x04 + +#undef CONFIG_USART0 +#define CONFIG_USART1 1 +#undef CONFIG_USART2 +#undef CONFIG_USART3 + +/* User serviceable stuff */ +#define CONFIG_DOS_PARTITION 1 + +#define CONFIG_CMDLINE_TAG 1 +#define CONFIG_SETUP_MEMORY_TAGS 1 +#define CONFIG_INITRD_TAG 1 + +#define CONFIG_STACKSIZE (2048) + +#define CONFIG_BAUDRATE 115200 +#define CONFIG_BOOTARGS \ + "console=ttyS0 root=mtd3 fbmem=2400k" + +#define CONFIG_BOOTCOMMAND \ + "fsload; bootm $(fileaddr)" + +/* + * Only interrupt autoboot if <space> is pressed. Otherwise, garbage + * data on the serial line may interrupt the boot sequence. + */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_AUTOBOOT 1 +#define CONFIG_AUTOBOOT_KEYED 1 +#define CONFIG_AUTOBOOT_PROMPT \ + "Press SPACE to abort autoboot in %d seconds\n" +#define CONFIG_AUTOBOOT_DELAY_STR "d" +#define CONFIG_AUTOBOOT_STOP_STR " " + +/* + * After booting the board for the first time, new ethernet addresses + * should be generated and assigned to the environment variables + * "ethaddr" and "eth1addr". This is normally done during production. + */ +#define CONFIG_OVERWRITE_ETHADDR_ONCE 1 +#define CONFIG_NET_MULTI 1 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_MMC + +#undef CONFIG_CMD_AUTOSCRIPT +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG + +#define CONFIG_ATMEL_USART 1 +#define CONFIG_MACB 1 +#define CONFIG_PIO2 1 +#define CFG_NR_PIOS 5 +#define CFG_HSDRAMC 1 +#define CONFIG_MMC 1 +#define CONFIG_ATMEL_MCI 1 + +#define CFG_DCACHE_LINESZ 32 +#define CFG_ICACHE_LINESZ 32 + +#define CONFIG_NR_DRAM_BANKS 1 + +/* External flash on STK1000 */ +#if 0 +#define CFG_FLASH_CFI 1 +#define CFG_FLASH_CFI_DRIVER 1 +#endif + +#define CFG_FLASH_BASE 0x00000000 +#define CFG_FLASH_SIZE 0x800000 +#define CFG_MAX_FLASH_BANKS 1 +#define CFG_MAX_FLASH_SECT 135 + +#define CFG_MONITOR_BASE CFG_FLASH_BASE + +#define CFG_INTRAM_BASE INTERNAL_SRAM_BASE +#define CFG_INTRAM_SIZE INTERNAL_SRAM_SIZE +#define CFG_SDRAM_BASE EBI_SDRAM_BASE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 65536 +#define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_FLASH_SIZE - CFG_ENV_SIZE) + +#define CFG_INIT_SP_ADDR (CFG_INTRAM_BASE + CFG_INTRAM_SIZE) + +#define CFG_MALLOC_LEN (256*1024) +#define CFG_DMA_ALLOC_LEN (16384) + +/* Allow 4MB for the kernel run-time image */ +#define CFG_LOAD_ADDR (EBI_SDRAM_BASE + 0x00400000) +#define CFG_BOOTPARAMS_LEN (16 * 1024) + +/* Other configuration settings that shouldn't have to change all that often */ +#define CFG_PROMPT "U-Boot> " +#define CFG_CBSIZE 256 +#define CFG_MAXARGS 16 +#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) +#define CFG_LONGHELP 1 + +#define CFG_MEMTEST_START EBI_SDRAM_BASE +#define CFG_MEMTEST_END (CFG_MEMTEST_START + 0x3f00000) +#define CFG_BAUDRATE_TABLE { 115200, 38400, 19200, 9600, 2400 } + +#endif /* __CONFIG_H */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 2f0df8a..41058f8 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -36,6 +36,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bamboo +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* @@ -49,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +86,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * NVRAM/RTC * @@ -223,15 +220,11 @@ #define SPD_EEPROM_ADDRESS {CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51} #define CFG_MBYTES_SDRAM (64) /* 64MB fixed size for early-sdram-init */ #define CONFIG_PROG_SDRAM_TLB -#undef CFG_DRAM_TEST /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -245,54 +238,20 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bamboo\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bamboo/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b 100000 fffa0000 60000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 @@ -300,16 +259,6 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #endif /* CONFIG_BAMBOO_NAND */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - #ifdef CONFIG_440EP /* USB */ #define CONFIG_USB_OHCI @@ -319,77 +268,27 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 #define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB #ifdef CONFIG_BAMBOO_NAND #define CONFIG_CMD_NAND #endif - #define CONFIG_SUPPORT_VFAT -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- * PCI stuff @@ -408,28 +307,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 75dd4e7..acce82f 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -37,6 +37,12 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bubinga +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ @@ -80,118 +86,35 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bubinga\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bubinga/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff90000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -205,29 +128,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -272,21 +177,9 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_SRAM_BASE 0xFFF00000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization @@ -423,21 +316,4 @@ #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/canmb.h b/include/configs/canmb.h index 0f7bb61..f097e2c 100644 --- a/include/configs/canmb.h +++ b/include/configs/canmb.h @@ -40,6 +40,8 @@ #define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 3dd577a..ac2e5d9 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -30,12 +30,19 @@ /* This config file is used for Canyonlands (460EX) and Glacier (460GT) */ #ifndef CONFIG_CANYONLANDS #define CONFIG_460GT 1 /* Specific PPC460GT */ +#define CONFIG_HOSTNAME glacier #else #define CONFIG_460EX 1 /* Specific PPC460EX */ +#define CONFIG_HOSTNAME canyonlands #endif #define CONFIG_440 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ @@ -47,8 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ - #define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ #define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CFG_PCI_TARGBASE CFG_PCI_MEMBASE @@ -86,10 +91,6 @@ #define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in OCM) *----------------------------------------------------------------------*/ @@ -102,13 +103,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -242,10 +238,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_SPEED 400000 /* I2C speed */ #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -270,7 +263,6 @@ * Ethernet *----------------------------------------------------------------------*/ #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 #define CONFIG_HAS_ETH0 @@ -282,14 +274,11 @@ #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #endif -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_DYNAMIC_ANEG 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - /*----------------------------------------------------------------------- * USB-OHCI *----------------------------------------------------------------------*/ @@ -305,104 +294,30 @@ #define CFG_USB_OHCI_MAX_ROOT_PORTS 15 #endif -/*----------------------------------------------------------------------- - * Default environment - *----------------------------------------------------------------------*/ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifdef CONFIG_CANYONLANDS -#define CONFIG_HOSTNAME canyonlands -#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0" -#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME glacier -#define CFG_BOOTFILE "bootfile=glacier/uImage\0" -#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_DTBFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 ${hostname}/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP #ifdef CONFIG_460EX #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT @@ -415,41 +330,6 @@ #define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ /* General PCI */ @@ -465,21 +345,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -671,8 +536,4 @@ } #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/cm5200.h b/include/configs/cm5200.h index d554348..ef50c7c 100644 --- a/include/configs/cm5200.h +++ b/include/configs/cm5200.h @@ -31,6 +31,8 @@ #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ #define CONFIG_CM5200 1 /* ... on CM5200 platform */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Supported commands */ diff --git a/include/configs/cpci5200.h b/include/configs/cpci5200.h index 1b30e51..fffd1fe 100644 --- a/include/configs/cpci5200.h +++ b/include/configs/cpci5200.h @@ -50,6 +50,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/davinci_sffsdr.h b/include/configs/davinci_sffsdr.h new file mode 100644 index 0000000..0e49e6c --- /dev/null +++ b/include/configs/davinci_sffsdr.h @@ -0,0 +1,150 @@ +/* + * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> + * + * Copyright (C) 2008 Lyrtech <www.lyrtech.com> + * Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/sizes.h> + +/* Board */ +#define SFFSDR +#define CFG_NAND_LARGEPAGE +#define CFG_USE_NAND +#define CFG_USE_DSPLINK /* This is to prevent U-Boot from + * powering ON the DSP. */ +/* SoC Configuration */ +#define CONFIG_ARM926EJS /* arm926ejs CPU core */ +#define CONFIG_SYS_CLK_FREQ 297000000 /* Arm Clock frequency */ +#define CFG_TIMERBASE 0x01c21400 /* use timer 0 */ +#define CFG_HZ_CLOCK 27000000 /* Timer Input clock freq */ +#define CFG_HZ 1000 +/* EEPROM definitions for Atmel 24LC64 EEPROM chip */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_I2C_EEPROM_ADDR 0x50 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +/* Memory Info */ +#define CFG_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */ +#define CFG_GBL_DATA_SIZE 128 /* reserved for initial data */ +#define CFG_MEMTEST_START 0x80000000 /* memtest start address */ +#define CFG_MEMTEST_END 0x81000000 /* 16MB RAM test */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define CONFIG_STACKSIZE (256*1024) /* regular stack */ +#define PHYS_SDRAM_1 0x80000000 /* DDR Start */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */ +#define DDR_4BANKS /* 4-bank DDR2 (128MB) */ +/* Serial Driver info */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 4 /* NS16550 register size */ +#define CFG_NS16550_COM1 0x01c20000 /* Base address of UART0 */ +#define CFG_NS16550_CLK 27000000 /* Input clock to NS16550 */ +#define CONFIG_CONS_INDEX 1 /* use UART0 for console */ +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +/* I2C Configuration */ +#define CONFIG_HARD_I2C +#define CONFIG_DRIVER_DAVINCI_I2C +#define CFG_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ +#define CFG_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ +/* Network & Ethernet Configuration */ +#define CONFIG_DRIVER_TI_EMAC +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 +#define CONFIG_OVERWRITE_ETHADDR_ONCE +/* Flash & Environment */ +#undef CFG_ENV_IS_IN_FLASH +#define CFG_NO_FLASH +#define CFG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ +#define CFG_ENV_SECT_SIZE 2048 /* Env sector Size */ +#define CFG_ENV_SIZE SZ_128K +#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ +#define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ +#define CFG_NAND_BASE 0x02000000 +#define CFG_NAND_HW_ECC +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ +#define NAND_MAX_CHIPS 1 +#define CFG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ +/* I2C switch definitions for PCA9543 chip */ +#define CFG_I2C_PCA9543_ADDR 0x70 +#define CFG_I2C_PCA9543_ADDR_LEN 0 /* Single register. */ +#define CFG_I2C_PCA9543_ENABLE_CH0 0x01 /* Enable channel 0. */ +/* U-Boot general configuration */ +#undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */ +#define CONFIG_MISC_INIT_R +#define CONFIG_BOOTDELAY 5 /* Autoboot after 5 seconds. */ +#define CONFIG_BOOTFILE "uImage" /* Boot file name */ +#define CFG_PROMPT "U-Boot > " /* Monitor Command Prompt */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_PBSIZE \ + (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* Print buffer size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x80700000 /* Default Linux kernel + * load address. */ +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, + * may be later */ +#define CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_CMDLINE_EDITING +#define CFG_LONGHELP +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC +/* Linux Information */ +#define LINUX_BOOT_PARAM_ADDR 0x80000100 +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTARGS \ + "mem=56M " \ + "console=ttyS0,115200n8 " \ + "root=/dev/nfs rw noinitrd ip=dhcp " \ + "nfsroot=${serverip}:/nfsroot/sffsdr " \ + "eth0=${ethaddr}" +#define CONFIG_BOOTCOMMAND \ + "nand read 87A00000 100000 300000;" \ + "bootelf 87A00000" +/* U-Boot commands */ +#include <config_cmd_default.h> +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_SAVES +#define CONFIG_CMD_NAND +#define CONFIG_CMD_EEPROM +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_FLASH +#undef CONFIG_CMD_IMLS +/* KGDB support (if any) */ +#ifdef CONFIG_CMD_KGDB +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ +#endif +#endif /* __CONFIG_H */ diff --git a/include/configs/dbau1x00.h b/include/configs/dbau1x00.h index b2f606f..0e10396 100644 --- a/include/configs/dbau1x00.h +++ b/include/configs/dbau1x00.h @@ -30,21 +30,21 @@ #define CONFIG_MIPS32 1 /* MIPS32 CPU core */ #define CONFIG_DBAU1X00 1 -#define CONFIG_AU1X00 1 /* alchemy series cpu */ +#define CONFIG_SOC_AU1X00 1 /* alchemy series cpu */ #ifdef CONFIG_DBAU1000 /* Also known as Merlot */ -#define CONFIG_AU1000 1 +#define CONFIG_SOC_AU1000 1 #else #ifdef CONFIG_DBAU1100 -#define CONFIG_AU1100 1 +#define CONFIG_SOC_AU1100 1 #else #ifdef CONFIG_DBAU1500 -#define CONFIG_AU1500 1 +#define CONFIG_SOC_AU1500 1 #else #ifdef CONFIG_DBAU1550 /* Cabernet */ -#define CONFIG_AU1550 1 +#define CONFIG_SOC_AU1550 1 #else #error "No valid board set" #endif @@ -148,7 +148,9 @@ #error "Invalid CPU frequency - must be multiple of 12!" #endif -#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */ +#define CFG_MIPS_TIMER_FREQ (CFG_MHZ * 1000000) + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 /* Cached addr */ diff --git a/include/configs/ebony.h b/include/configs/ebony.h index ba68fd4..df444d8 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -35,10 +35,15 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME ebony +#include "amcc-common.h" + +/* * Define here the location of the environment variables (FLASH or NVRAM). * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only * supported for backward compatibility. @@ -55,7 +60,6 @@ *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -74,18 +78,11 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} /*----------------------------------------------------------------------- * NVRAM/RTC @@ -141,10 +138,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -153,125 +147,31 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=ebony\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/ebony/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=ff800000\0" \ "ramdisk_addr=ff810000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 8 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -288,28 +188,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/gth2.h b/include/configs/gth2.h index c2a50c1..c2d6ca7 100644 --- a/include/configs/gth2.h +++ b/include/configs/gth2.h @@ -30,9 +30,9 @@ #define CONFIG_MIPS32 1 /* MIPS32 CPU core */ #define CONFIG_GTH2 1 -#define CONFIG_AU1X00 1 /* alchemy series cpu */ +#define CONFIG_SOC_AU1X00 1 /* alchemy series cpu */ -#define CONFIG_AU1000 1 +#define CONFIG_SOC_AU1000 1 #define CONFIG_MISC_INIT_R 1 @@ -118,7 +118,9 @@ #define CFG_MHZ 500 -#define CFG_HZ (CFG_MHZ * 1000000) /* FIXME causes overflow in net.c */ +#define CFG_MIPS_TIMER_FREQ (CFG_MHZ * 1000000) + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 /* Cached addr */ diff --git a/include/configs/hmi1001.h b/include/configs/hmi1001.h index e5a8897..ad7cf76 100644 --- a/include/configs/hmi1001.h +++ b/include/configs/hmi1001.h @@ -40,6 +40,8 @@ #define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/imx31_litekit.h b/include/configs/imx31_litekit.h index 4281d73..ec4ed1e 100644 --- a/include/configs/imx31_litekit.h +++ b/include/configs/imx31_litekit.h @@ -65,7 +65,8 @@ #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 -#define CONFIG_MXC_SPI_IFACE 1 +#define CONFIG_DEFAULT_SPI_BUS 1 +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 diff --git a/include/configs/incaip.h b/include/configs/incaip.h index 5ca00b3..2e4ee66 100644 --- a/include/configs/incaip.h +++ b/include/configs/incaip.h @@ -118,7 +118,9 @@ #define CFG_BOOTPARAMS_LEN 128*1024 -#define CFG_HZ (incaip_get_cpuclk() / 2) +#define CFG_MIPS_TIMER_FREQ (incaip_get_cpuclk() / 2) + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 diff --git a/include/configs/inka4x0.h b/include/configs/inka4x0.h index c89f041..6ec92c3 100644 --- a/include/configs/inka4x0.h +++ b/include/configs/inka4x0.h @@ -40,6 +40,8 @@ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h index 980e9fe..c985927 100644 --- a/include/configs/jupiter.h +++ b/include/configs/jupiter.h @@ -41,6 +41,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index cce883f..d3789bd 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -37,8 +37,14 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ -#undef CFG_DRAM_TEST /* Disable-takes long time */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME katmai +#include "amcc-common.h" #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ @@ -48,7 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -78,10 +83,6 @@ #define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ @@ -98,12 +99,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CFG_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * DDR SDRAM @@ -117,10 +114,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE @@ -172,139 +166,36 @@ *----------------------------------------------------------------------*/ #define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=katmai\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 200000 - ${fdt_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=katmai/uImage\0" \ - "fdt_file=katmai/katmai.dtb\0" \ - "fdt_addr=400000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 katmai/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "kozio=bootm ffc60000\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP #define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * FLASH related @@ -436,28 +327,4 @@ #define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) #define CFG_GPIO_ODR 0 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index a596768..9c1a3a4 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -1,4 +1,7 @@ /* + * Copyright (c) 2008 Nuovation System Designs, LLC + * Grant Erickson <gerickson@nuovations.com> + * * (C) Copyright 2007 * Stefan Roese, DENX Software Engineering, sr@denx.de. * @@ -36,6 +39,12 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME kilauea +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ #define CONFIG_BOARD_EMAC_COUNT @@ -44,43 +53,70 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_NAND_ADDR 0xF8000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- - * Initial RAM & stack pointer - *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */ -#define CFG_INIT_RAM_END (4 << 10) + * Initial RAM & Stack Pointer Configuration Options + * + * There are traditionally three options for the primordial + * (i.e. initial) stack usage on the 405-series: + * + * 1) On-chip Memory (OCM) (i.e. SRAM) + * 2) Data cache + * 3) SDRAM + * + * For the 405EX(r), there is no OCM, so we are left with (2) or (3) + * the latter of which is less than desireable since it requires + * setting up the SDRAM and ECC in assembly code. + * + * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip + * select on the External Bus Controller (EBC) and then select a + * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid, + * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and + * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid, + * physical SDRAM to use (3). + *-----------------------------------------------------------------------*/ + +#define CFG_INIT_DCACHE_CS 4 + +#if defined(CFG_INIT_DCACHE_CS) +#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ +#else +#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */ +#endif /* defined(CFG_INIT_DCACHE_CS) */ + +#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */ #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -/* reserve some memory for POST and BOOT limit info */ -#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) -/* extra data in init-ram */ -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) -#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8) -#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12) -#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */ +/* + * If the data cache is being used for the primordial stack and global + * data area, the POST word must be placed somewhere else. The General + * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves + * its compare and mask register contents across reset, so it is used + * for the POST word. + */ + +#if defined(CFG_INIT_DCACHE_CS) +# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6) +#else +# define CFG_INIT_EXTRA_SIZE 16 +# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE) +# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) +# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR +#endif /* defined(CFG_INIT_DCACHE_CS) */ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -131,9 +167,9 @@ * This NAND U-Boot (NUB) is a special U-Boot version which can be started * from RAM. Therefore it mustn't (re-)configure the SDRAM controller. * - * On 440EPx the SPL is copied to SDRAM before the NAND controller is - * set up. While still running from cache, I experienced problems accessing - * the NAND controller. sr - 2006-08-25 + * On 405EX the SPL is copied to SDRAM before the NAND controller is + * set up. While still running from location 0xfffff000...0xffffffff the + * NAND controller cannot be accessed since it is attached to CS0 too. */ #define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ #define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ @@ -187,12 +223,54 @@ *----------------------------------------------------------------------*/ #define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE) + +/* DDR1/2 SDRAM Device Control Register Data Values */ +#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \ + SDRAM_RXBAS_SDSZ_256MB | \ + SDRAM_RXBAS_SDAM_MODE7 | \ + SDRAM_RXBAS_SDBE_ENABLE) +#define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE +#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE +#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE +#define CFG_SDRAM0_MCOPT1 0x04322000 +#define CFG_SDRAM0_MCOPT2 0x00000000 +#define CFG_SDRAM0_MODT0 0x01800000 +#define CFG_SDRAM0_MODT1 0x00000000 +#define CFG_SDRAM0_CODT 0x0080f837 +#define CFG_SDRAM0_RTR 0x06180000 +#define CFG_SDRAM0_INITPLR0 0xa8380000 +#define CFG_SDRAM0_INITPLR1 0x81900400 +#define CFG_SDRAM0_INITPLR2 0x81020000 +#define CFG_SDRAM0_INITPLR3 0x81030000 +#define CFG_SDRAM0_INITPLR4 0x81010404 +#define CFG_SDRAM0_INITPLR5 0x81000542 +#define CFG_SDRAM0_INITPLR6 0x81900400 +#define CFG_SDRAM0_INITPLR7 0x8D080000 +#define CFG_SDRAM0_INITPLR8 0x8D080000 +#define CFG_SDRAM0_INITPLR9 0x8D080000 +#define CFG_SDRAM0_INITPLR10 0x8D080000 +#define CFG_SDRAM0_INITPLR11 0x81000442 +#define CFG_SDRAM0_INITPLR12 0x81010780 +#define CFG_SDRAM0_INITPLR13 0x81010400 +#define CFG_SDRAM0_INITPLR14 0x00000000 +#define CFG_SDRAM0_INITPLR15 0x00000000 +#define CFG_SDRAM0_RQDC 0x80000038 +#define CFG_SDRAM0_RFDC 0x00000209 +#define CFG_SDRAM0_RDCC 0x40000000 +#define CFG_SDRAM0_DLCR 0x030000a5 +#define CFG_SDRAM0_CLKTR 0x80000000 +#define CFG_SDRAM0_WRDTR 0x00000000 +#define CFG_SDRAM0_SDTR1 0x80201000 +#define CFG_SDRAM0_SDTR2 0x32204232 +#define CFG_SDRAM0_SDTR3 0x080b0d1a +#define CFG_SDRAM0_MMODE 0x00000442 +#define CFG_SDRAM0_MEMODE 0x00000404 + /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -212,7 +290,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -220,107 +297,37 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 2 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=kilauea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self_old=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=kilauea/uImage\0" \ - "fdt_file=kilauea/kilauea.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 kilauea/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CACHE | \ +#define CONFIG_POST (CFG_POST_CACHE | \ CFG_POST_CPU | \ CFG_POST_ETHER | \ CFG_POST_I2C | \ @@ -335,37 +342,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -394,13 +370,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -429,7 +398,7 @@ /* Memory Bank 2 (FPGA) initialization */ #define CFG_EBC_PB2AP 0x9400C800 -#define CFG_EBC_PB2CR 0xF0018000 /* BAS=0x800,BS=1MB,BU=R/W,BW=8bit */ +#define CFG_EBC_PB2CR (CFG_FPGA_BASE | 0x18000) #define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ @@ -474,19 +443,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * Some Kilauea stuff..., mainly fpga registers */ @@ -522,8 +478,4 @@ #define CFG_FPGA_USER_LED0 0x00000200 #define CFG_FPGA_USER_LED1 0x00000100 -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/luan.h b/include/configs/luan.h index 37151d3..805cc59 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -37,6 +37,12 @@ #define CONFIG_440 1 #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME luan +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ @@ -44,11 +50,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */ - #define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */ #define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */ #define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */ @@ -68,7 +69,6 @@ #define CFG_FLASH_BASE CFG_SMALL_FLASH #endif -#undef CFG_DRAM_TEST #if CFG_SRAM_BASE #define CFG_KBYTES_SDRAM 1024*2 #else @@ -88,13 +88,8 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#undef CONFIG_SERIAL_MULTI #undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -139,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -151,61 +143,22 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=luan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/luan/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc100000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #ifdef DEBUG #define CONFIG_PANIC_HANG #else @@ -213,60 +166,11 @@ #endif /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#undef CONFIG_LYNXKDI /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -287,28 +191,4 @@ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index af066f3..65b240e 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -1,4 +1,7 @@ /* + * Copyright (c) 2008 Nuovation System Designs, LLC + * Grant Erickson <gerickson@nuovations.com> + * * (C) Copyright 2007-2008 * Stefan Roese, DENX Software Engineering, sr@denx.de. * @@ -36,6 +39,13 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME makalu +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -43,42 +53,69 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- - * Initial RAM & stack pointer - *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0x02000000 /* inside of SDRAM */ -#define CFG_INIT_RAM_END (4 << 10) + * Initial RAM & Stack Pointer Configuration Options + * + * There are traditionally three options for the primordial + * (i.e. initial) stack usage on the 405-series: + * + * 1) On-chip Memory (OCM) (i.e. SRAM) + * 2) Data cache + * 3) SDRAM + * + * For the 405EX(r), there is no OCM, so we are left with (2) or (3) + * the latter of which is less than desireable since it requires + * setting up the SDRAM and ECC in assembly code. + * + * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip + * select on the External Bus Controller (EBC) and then select a + * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid, + * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and + * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid, + * physical SDRAM to use (3). + *-----------------------------------------------------------------------*/ + +#define CFG_INIT_DCACHE_CS 4 + +#if defined(CFG_INIT_DCACHE_CS) +#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ +#else +#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */ +#endif /* defined(CFG_INIT_DCACHE_CS) */ + +#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */ #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -/* reserve some memory for POST and BOOT limit info */ -#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 16) -/* extra data in init-ram */ -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) -#define CFG_POST_MAGIC (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8) -#define CFG_POST_VAL (CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12) -#define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR /* for commproc.c */ +/* + * If the data cache is being used for the primordial stack and global + * data area, the POST word must be placed somewhere else. The General + * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves + * its compare and mask register contents across reset, so it is used + * for the POST word. + */ + +#if defined(CFG_INIT_DCACHE_CS) +# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6) +#else +# define CFG_INIT_EXTRA_SIZE 16 +# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE) +# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) +# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR +#endif /* defined(CFG_INIT_DCACHE_CS) */ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -113,14 +150,60 @@ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM 256 +#define CFG_MBYTES_SDRAM (256) /* 256MB */ + +#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE) +#define CFG_SDRAM0_MB1CF_BASE ((128 << 20) + CFG_SDRAM_BASE) + +/* DDR1/2 SDRAM Device Control Register Data Values */ +#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \ + SDRAM_RXBAS_SDSZ_128MB | \ + SDRAM_RXBAS_SDAM_MODE2 | \ + SDRAM_RXBAS_SDBE_ENABLE) +#define CFG_SDRAM0_MB1CF ((CFG_SDRAM0_MB1CF_BASE >> 3) | \ + SDRAM_RXBAS_SDSZ_128MB | \ + SDRAM_RXBAS_SDAM_MODE2 | \ + SDRAM_RXBAS_SDBE_ENABLE) +#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE +#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE +#define CFG_SDRAM0_MCOPT1 0x04322000 +#define CFG_SDRAM0_MCOPT2 0x00000000 +#define CFG_SDRAM0_MODT0 0x01800000 +#define CFG_SDRAM0_MODT1 0x00000000 +#define CFG_SDRAM0_CODT 0x0080f837 +#define CFG_SDRAM0_RTR 0x06180000 +#define CFG_SDRAM0_INITPLR0 0xa8380000 +#define CFG_SDRAM0_INITPLR1 0x81900400 +#define CFG_SDRAM0_INITPLR2 0x81020000 +#define CFG_SDRAM0_INITPLR3 0x81030000 +#define CFG_SDRAM0_INITPLR4 0x81010404 +#define CFG_SDRAM0_INITPLR5 0x81000542 +#define CFG_SDRAM0_INITPLR6 0x81900400 +#define CFG_SDRAM0_INITPLR7 0x8D080000 +#define CFG_SDRAM0_INITPLR8 0x8D080000 +#define CFG_SDRAM0_INITPLR9 0x8D080000 +#define CFG_SDRAM0_INITPLR10 0x8D080000 +#define CFG_SDRAM0_INITPLR11 0x81000442 +#define CFG_SDRAM0_INITPLR12 0x81010780 +#define CFG_SDRAM0_INITPLR13 0x81010400 +#define CFG_SDRAM0_INITPLR14 0x00000000 +#define CFG_SDRAM0_INITPLR15 0x00000000 +#define CFG_SDRAM0_RQDC 0x80000038 +#define CFG_SDRAM0_RFDC 0x00000209 +#define CFG_SDRAM0_RDCC 0x40000000 +#define CFG_SDRAM0_DLCR 0x030000a5 +#define CFG_SDRAM0_CLKTR 0x80000000 +#define CFG_SDRAM0_WRDTR 0x00000000 +#define CFG_SDRAM0_SDTR1 0x80201000 +#define CFG_SDRAM0_SDTR2 0x32204232 +#define CFG_SDRAM0_SDTR3 0x080b0d1a +#define CFG_SDRAM0_MMODE 0x00000442 +#define CFG_SDRAM0_MEMODE 0x00000404 /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -140,7 +223,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -148,104 +230,35 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=makalu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \ - "flash_self_old=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=makalu/uImage\0" \ - "fdt_file=makalu/makalu.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 makalu/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CACHE | \ +#define CONFIG_POST (CFG_POST_CACHE | \ CFG_POST_CPU | \ CFG_POST_ETHER | \ CFG_POST_I2C | \ @@ -260,37 +273,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -319,13 +301,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -384,21 +359,4 @@ #define CFG_GPIO_PCIE_CLKREQ 27 #define CFG_GPIO_PCIE_WAKE 28 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/mcc200.h b/include/configs/mcc200.h index a9c86f9..e4c3f72 100644 --- a/include/configs/mcc200.h +++ b/include/configs/mcc200.h @@ -40,6 +40,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration * diff --git a/include/configs/mecp5200.h b/include/configs/mecp5200.h index 5218d9c..8dfb9aa 100644 --- a/include/configs/mecp5200.h +++ b/include/configs/mecp5200.h @@ -50,6 +50,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/ml300.h b/include/configs/ml300.h index 1945918..319923a 100644 --- a/include/configs/ml300.h +++ b/include/configs/ml300.h @@ -54,6 +54,7 @@ #define CONFIG_405 1 /* This is a PPC405 CPU */ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ +#define CONFIG_XILINX_405 1 #define CONFIG_XILINX_ML300 1 /* ...on a Xilinx ML300 board */ #define CONFIG_SYSTEMACE 1 diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h index 1503598..b6843af 100644 --- a/include/configs/motionpro.h +++ b/include/configs/motionpro.h @@ -35,6 +35,7 @@ #define CONFIG_MPC5200 1 /* More exactly a MPC5200 */ #define CONFIG_MOTIONPRO 1 /* ... on Promess Motion-PRO board */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * BOOTP options diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h index f614e67..2f24967 100644 --- a/include/configs/mpc7448hpc2.h +++ b/include/configs/mpc7448hpc2.h @@ -39,7 +39,7 @@ #define CONFIG_MPC7448HPC2 #define CONFIG_74xx -#define CONFIG_750FX /* this option to enable init of extended BATs */ +#define CONFIG_HIGH_BATS /* High BATs supported */ #define CONFIG_ALTIVEC /* undef to disable */ #define CFG_BOARD_NAME "MPC7448 HPC II" @@ -58,6 +58,7 @@ #define CONFIG_BOARD_EARLY_INIT_R #define CONFIG_MISC_INIT_R +#define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_ENV_OVERWRITE @@ -75,7 +76,7 @@ #define CFG_PROMPT_HUSH_PS2 "> " /* Pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +#define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define OF_CPU "PowerPC,7448@0" diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h index 8d92a13..7298e55 100644 --- a/include/configs/ms7722se.h +++ b/include/configs/ms7722se.h @@ -40,10 +40,6 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTARGS "console=ttySC0,115200 root=1f01" -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.0.22 -#define CONFIG_SERVERIP 192.168.0.1 -#define CONFIG_GATEWAYIP 192.168.0.1 #define CONFIG_VERSION_VARIABLE #undef CONFIG_SHOW_BOOT_PROGRESS diff --git a/include/configs/munices.h b/include/configs/munices.h index 38b27bb..e0046ec 100644 --- a/include/configs/munices.h +++ b/include/configs/munices.h @@ -35,6 +35,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * Command line configuration. diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h index 2ea48a6..37ba872 100644 --- a/include/configs/mx31ads.h +++ b/include/configs/mx31ads.h @@ -62,7 +62,8 @@ #define CONFIG_HARD_SPI 1 #define CONFIG_MXC_SPI 1 -#define CONFIG_MXC_SPI_IFACE 1 /* Default SPI interface number */ +#define CONFIG_DEFAULT_SPI_BUS 1 +#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_2 | SPI_CS_HIGH) #define CONFIG_RTC_MC13783 1 diff --git a/include/configs/o2dnt.h b/include/configs/o2dnt.h index 8dde1ef..88bdb03 100644 --- a/include/configs/o2dnt.h +++ b/include/configs/o2dnt.h @@ -37,6 +37,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h index be2b3ec..407aae7 100644 --- a/include/configs/ocotea.h +++ b/include/configs/ocotea.h @@ -44,16 +44,19 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME ocotea +#include "amcc-common.h" + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -75,18 +78,11 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * Environment @@ -156,10 +152,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -168,54 +161,17 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=ocotea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/ocotea/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 2 #define CONFIG_PHY2_ADDR 0x10 @@ -228,73 +184,15 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -311,28 +209,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h index 0dac516..0913b14 100644 --- a/include/configs/p3mx.h +++ b/include/configs/p3mx.h @@ -42,6 +42,7 @@ #if defined (CONFIG_P3M750) #define CONFIG_750FX /* 750GL/GX/FX */ +#define CONFIG_HIGH_BATS /* High BATs supported */ #define CFG_BOARD_NAME "P3M750" #define CFG_BUS_HZ 100000000 #define CFG_BUS_CLK CFG_BUS_HZ diff --git a/include/configs/pb1x00.h b/include/configs/pb1x00.h index 810e0f0..2caa641 100644 --- a/include/configs/pb1x00.h +++ b/include/configs/pb1x00.h @@ -30,16 +30,16 @@ #define CONFIG_MIPS32 1 /* MIPS32 CPU core */ #define CONFIG_PB1X00 1 -#define CONFIG_AU1X00 1 /* alchemy series cpu */ +#define CONFIG_SOC_AU1X00 1 /* alchemy series cpu */ #ifdef CONFIG_PB1000 -#define CONFIG_AU1000 1 +#define CONFIG_SOC_AU1000 1 #else #ifdef CONFIG_PB1100 -#define CONFIG_AU1100 1 +#define CONFIG_SOC_AU1100 1 #else #ifdef CONFIG_PB1500 -#define CONFIG_AU1500 1 +#define CONFIG_SOC_AU1500 1 #else #error "No valid board set" #endif @@ -81,7 +81,9 @@ #define CFG_BOOTPARAMS_LEN 128*1024 -#define CFG_HZ 396000000 /* FIXME causes overflow in net.c */ +#define CFG_MIPS_TIMER_FREQ 396000000 + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 /* Cached addr */ diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h index 2ce39c9..c065d33 100644 --- a/include/configs/pf5200.h +++ b/include/configs/pf5200.h @@ -49,6 +49,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* * Serial console configuration */ diff --git a/include/configs/purple.h b/include/configs/purple.h index 1be4e05..ef92637 100644 --- a/include/configs/purple.h +++ b/include/configs/purple.h @@ -114,7 +114,8 @@ #define CFG_PROMPT "PURPLE # " /* Monitor Command Prompt */ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_HZ (CPU_CLOCK_RATE/2) +#define CFG_MIPS_TIMER_FREQ (CPU_CLOCK_RATE/2) +#define CFG_HZ 1000 #define CFG_MAXARGS 16 /* max number of command args*/ #define CFG_LOAD_ADDR 0x80500000 /* default load address */ diff --git a/include/configs/qemu-mips.h b/include/configs/qemu-mips.h index d6bcc8e..3dfd218 100644 --- a/include/configs/qemu-mips.h +++ b/include/configs/qemu-mips.h @@ -120,7 +120,9 @@ #define CFG_MHZ 132 -#define CFG_HZ (CFG_MHZ * 1000000) +#define CFG_MIPS_TIMER_FREQ (CFG_MHZ * 1000000) + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 /* Cached addr */ diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h new file mode 100644 index 0000000..622a5d4 --- /dev/null +++ b/include/configs/quad100hd.h @@ -0,0 +1,298 @@ +/* + * (C) Copyright 2008 + * Gary Jennejohn, DENX Software Engineering GmbH, garyj@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * quad100hd.h - configuration for Quad100hd board + ***********************************************************************/ +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_QUAD100HD 1 /* Board is Quad100hd */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_405EP 1 /* Specifc 405EP support*/ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ + +#define PLLMR0_DEFAULT PLLMR0_266_133_66 /* no PCI */ +#define PLLMR1_DEFAULT PLLMR1_266_133_66 /* no PCI */ + +/* the environment is in the EEPROM by default */ +#define CFG_ENV_IS_IN_EEPROM +#undef CFG_ENV_IS_IN_FLASH + +#define CONFIG_NET_MULTI 1 +#define CONFIG_HAS_ETH1 1 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 0x01 /* PHY address */ +#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_PHY_RESET 1 +#define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_ASKENV +#undef CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#undef CONFIG_CMD_DIAG +#define CONFIG_CMD_EEPROM +#undef CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#undef CONFIG_CMD_IRQ +#define CONFIG_CMD_JFFS2 +#undef CONFIG_CMD_LOG +#undef CONFIG_CMD_MII +#define CONFIG_CMD_NAND +#undef CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/*----------------------------------------------------------------------- + * SDRAM + *----------------------------------------------------------------------*/ +/* + * SDRAM configuration (please see cpu/ppc/sdram.[ch]) + */ +#define CONFIG_SDRAM_BANK0 1 +#define CFG_SDRAM_SIZE 0x02000000 /* 32 MB */ + +/* FIX! SDRAM timings used in datasheet */ +#define CFG_SDRAM_CL 3 /* CAS latency */ +#define CFG_SDRAM_tRP 20 /* PRECHARGE command period */ +#define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ +#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ +#define CFG_SDRAM_tRFC 66 /* Auto refresh period */ + +/* + * JFFS2 + */ +#define CFG_JFFS2_FIRST_BANK 0 +#ifdef CFG_KERNEL_IN_JFFS2 +#define CFG_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */ +#else /* kernel not in JFFS */ +#define CFG_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */ +#endif +#define CFG_JFFS2_NUM_BANKS 1 + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ +#define CFG_BASE_BAUD 691200 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI + +/* The following table includes the supported baudrates */ +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} + +/*----------------------------------------------------------------------- + * Miscellaneous configurable options + *----------------------------------------------------------------------*/ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_info (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CFG_I2C_EEPROM_ADDR 0x50 /* base address */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ + +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CFG_EEPROM_SIZE 0x2000 + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0xFFC00000 +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CFG_MONITOR_BASE (TEXT_BASE) + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER + +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_INCREMENT 0 /* there is only one bank */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ +/* the environment is located before u-boot */ +#define CFG_ENV_ADDR (TEXT_BASE - CFG_ENV_SECT_SIZE) + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR - CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SECT_SIZE) +#endif + +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x400 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x00000000 +#define CFG_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */ +#endif + +/* partly from PPCBoot */ +/* NAND */ +#define CONFIG_NAND +#ifdef CONFIG_NAND +#define CFG_NAND_BASE 0x60000000 +#define CFG_NAND_CS 10 /* our CS is GPIO10 */ +#define CFG_NAND_RDY 23 /* our RDY is GPIO23 */ +#define CFG_NAND_CE 24 /* our CE is GPIO24 */ +#define CFG_NAND_CLE 31 /* our CLE is GPIO31 */ +#define CFG_NAND_ALE 30 /* our ALE is GPIO30 */ +#define NAND_MAX_CHIPS 1 +#define CFG_MAX_NAND_DEVICE 1 +#endif + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in data cache) + */ +/* use on chip memory (OCM) for temperary stack until sdram is tested */ +/* see ./cpu/ppc4xx/start.S */ +#define CFG_TEMP_STACK_OCM 1 + +/* On Chip Memory location */ +#define CFG_OCM_DATA_ADDR 0xF8000000 +#define CFG_OCM_DATA_SIZE 0x1000 +#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of OCM */ +#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + * Taken from PPCBoot board/icecube/icecube.h + */ + +/* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */ +#define CFG_EBC_PB0AP 0x04002480 +/* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */ +#define CFG_EBC_PB0CR 0xFFC5A000 +#define CFG_EBC_PB1AP 0x04005480 +#define CFG_EBC_PB1CR 0x60018000 +#define CFG_EBC_PB2AP 0x00000000 +#define CFG_EBC_PB2CR 0x00000000 +#define CFG_EBC_PB3AP 0x00000000 +#define CFG_EBC_PB3CR 0x00000000 +#define CFG_EBC_PB4AP 0x00000000 +#define CFG_EBC_PB4CR 0x00000000 + +/*----------------------------------------------------------------------- + * Definitions for GPIO setup (PPC405EP specific) + * + * Taken in part from PPCBoot board/icecube/icecube.h + */ +/* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */ +#define CFG_GPIO0_OSRH 0x55555550 +#define CFG_GPIO0_OSRL 0x00000110 +#define CFG_GPIO0_ISR1H 0x00000000 +#define CFG_GPIO0_ISR1L 0x15555445 +#define CFG_GPIO0_TSRH 0x00000000 +#define CFG_GPIO0_TSRL 0x00000000 +#define CFG_GPIO0_TCR 0xFFFF8097 +#define CFG_GPIO0_ODR 0x00000000 + +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* ENVIRONMENT VARS */ + +#define CONFIG_IPADDR 192.168.1.67 +#define CONFIG_SERVERIP 192.168.1.50 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 +#define CONFIG_LOADADDR 300000 +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 + +#endif /* __CONFIG_H */ diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h index c20baca..e269336 100644 --- a/include/configs/r2dplus.h +++ b/include/configs/r2dplus.h @@ -35,12 +35,6 @@ #define CONFIG_BOOTARGS "console=ttySC0,115200" #define CONFIG_ENV_OVERWRITE 1 -/* Network setting */ -#define CONFIG_NETMASK 255.0.0.0 -#define CONFIG_IPADDR 10.0.192.51 -#define CONFIG_SERVERIP 10.0.0.1 -#define CONFIG_GATEWAYIP 10.0.0.1 - /* SDRAM */ #define CFG_SDRAM_BASE (0x8C000000) #define CFG_SDRAM_SIZE (0x04000000) @@ -60,45 +54,27 @@ #define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 32 * 1024 * 1024) /* Address of u-boot image in Flash */ #define CFG_MONITOR_BASE (CFG_FLASH_BASE) -#define CFG_MONITOR_LEN (128 * 1024) +#define CFG_MONITOR_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ -#define CFG_MALLOC_LEN (256 * 1024) +#define CFG_MALLOC_LEN (1024 * 1024) /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_SIZE (256) #define CFG_BOOTMAPSZ (8 * 1024 * 1024) /* - * NOR Flash + * NOR Flash ( Spantion S29GL256P ) */ #define CFG_FLASH_CFI #define CFG_FLASH_CFI_DRIVER - -#if defined(CONFIG_R2DPLUS_OLD) -#define CFG_FLASH_BASE (0xA0000000) -#define CFG_MAX_FLASH_BANKS (1) /* Max number of - * Flash memory banks - */ -#define CFG_MAX_FLASH_SECT 142 -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } - -#else /* CONFIG_R2DPLUS_OLD */ - #define CFG_FLASH_BASE (0xA0000000) -#define CFG_FLASH_CFI_WIDTH 0x04 /* 32bit */ -#define CFG_MAX_FLASH_BANKS (2) -#define CFG_MAX_FLASH_SECT 270 -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE,\ - CFG_FLASH_BASE + 0x100000,\ - CFG_FLASH_BASE + 0x400000,\ - CFG_FLASH_BASE + 0x700000, } -#endif /* CONFIG_R2DPLUS_OLD */ +#define CFG_MAX_FLASH_BANKS (1) +#define CFG_MAX_FLASH_SECT 256 +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } #define CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x20000 -#define CFG_ENV_SIZE (CFG_ENV_SECT_SIZE) -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) -#define CFG_FLASH_ERASE_TOUT 120000 -#define CFG_FLASH_WRITE_TOUT 500 +#define CFG_ENV_SECT_SIZE 0x40000 +#define CFG_ENV_SIZE (CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) /* * SuperH Clock setting diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h index 4e89580..4c82c5a 100644 --- a/include/configs/r7780mp.h +++ b/include/configs/r7780mp.h @@ -1,7 +1,7 @@ /* * Configuation settings for the Renesas R7780MP board * - * Copyright (C) 2007 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + * Copyright (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> * Copyright (C) 2008 Yusuke Goda <goda.yusuke@renesas.com> * * See file CREDITS for list of people who contributed to this @@ -31,7 +31,8 @@ #define CONFIG_SH4A 1 #define CONFIG_CPU_SH7780 1 #define CONFIG_R7780MP 1 -#define __LITTLE_ENDIAN 1 +#define CFG_R7780MP_OLD_FLASH 1 +#define __LITTLE_ENDIAN__ 1 /* * Command line configuration. @@ -59,12 +60,6 @@ /* check for keypress on bootdelay==0 */ /*#define CONFIG_ZERO_BOOTDELAY_CHECK*/ -/* Network setting */ -#define CONFIG_NETMASK 255.0.0.0 -#define CONFIG_IPADDR 10.0.192.82 -#define CONFIG_SERVERIP 10.0.0.1 -#define CONFIG_GATEWAYIP 10.0.0.1 - #define CFG_SDRAM_BASE (0x08000000) #define CFG_SDRAM_SIZE (128 * 1024 * 1024) @@ -80,22 +75,30 @@ #define CFG_MEMTEST_START (CFG_SDRAM_BASE) #define CFG_MEMTEST_END (TEXT_BASE - 0x100000) -/* NOR Flash (S29PL127J60TFI130) */ +/* Flash board support */ #define CFG_FLASH_BASE (0xA0000000) -#define CFG_FLASH_CFI_WIDTH FLASH_CFI_32BIT -#define CFG_MAX_FLASH_BANKS (2) -#define CFG_MAX_FLASH_SECT 270 -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE,\ +#ifdef CFG_R7780MP_OLD_FLASH +/* NOR Flash (S29PL127J60TFI130) */ +# define CFG_FLASH_CFI_WIDTH FLASH_CFI_32BIT +# define CFG_MAX_FLASH_BANKS (2) +# define CFG_MAX_FLASH_SECT 270 +# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE,\ CFG_FLASH_BASE + 0x100000,\ CFG_FLASH_BASE + 0x400000,\ CFG_FLASH_BASE + 0x700000, } +#else /* CFG_R7780MP_OLD_FLASH */ +/* NOR Flash (Spantion S29GL256P) */ +# define CFG_MAX_FLASH_BANKS (1) +# define CFG_MAX_FLASH_SECT 256 +# define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#endif /* CFG_R7780MP_OLD_FLASH */ #define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 4 * 1024 * 1024) /* Address of u-boot image in Flash */ #define CFG_MONITOR_BASE (CFG_FLASH_BASE) -#define CFG_MONITOR_LEN (112 * 1024) +#define CFG_MONITOR_LEN (256 * 1024) /* Size of DRAM reserved for malloc() use */ -#define CFG_MALLOC_LEN (256 * 1024) +#define CFG_MALLOC_LEN (1204 * 1024) /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_SIZE (256) @@ -110,7 +113,7 @@ #define CFG_FLASH_EMPTY_INFO #define CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE (16 * 1024) +#define CFG_ENV_SECT_SIZE (256 * 1024) #define CFG_ENV_SIZE (CFG_ENV_SECT_SIZE) #define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) #define CFG_FLASH_ERASE_TOUT 120000 @@ -141,8 +144,10 @@ #endif /* CONFIG_CMD_PCI */ #if defined(CONFIG_CMD_NET) -/* #define CONFIG_NET_MULTI - #define CONFIG_RTL8169 */ +/* +#define CONFIG_NET_MULTI +#define CONFIG_RTL8169 +*/ /* AX88696L Support(NE2000 base chip) */ #define CONFIG_DRIVER_NE2000 #define CONFIG_DRIVER_AX88796L diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h index 4974fb4..2a398e8 100644 --- a/include/configs/sacsng.h +++ b/include/configs/sacsng.h @@ -272,10 +272,14 @@ #undef SPI_INIT /* no port initialization needed */ #define SPI_READ ((immr->im_ioport.iop_pdatd & I2C_MISO) != 0) -#define SPI_SDA(bit) if(bit) immr->im_ioport.iop_pdatd |= I2C_MOSI; \ - else immr->im_ioport.iop_pdatd &= ~I2C_MOSI -#define SPI_SCL(bit) if(bit) immr->im_ioport.iop_pdatd |= I2C_SCLK; \ - else immr->im_ioport.iop_pdatd &= ~I2C_SCLK +#define SPI_SDA(bit) do { \ + if(bit) immr->im_ioport.iop_pdatd |= I2C_MOSI; \ + else immr->im_ioport.iop_pdatd &= ~I2C_MOSI; \ + } while (0) +#define SPI_SCL(bit) do { \ + if(bit) immr->im_ioport.iop_pdatd |= I2C_SCLK; \ + else immr->im_ioport.iop_pdatd &= ~I2C_SCLK; \ + } while (0) #define SPI_DELAY /* No delay is needed */ #endif /* CONFIG_SOFT_SPI */ diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h index 0ebc674..7481556 100644 --- a/include/configs/sbc8349.h +++ b/include/configs/sbc8349.h @@ -570,6 +570,8 @@ #define CFG_HID2 HID2_HBE +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* DDR @ 0x00000000 */ #define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 81a1e07..146eafe 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -42,6 +42,7 @@ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_SBC8560 1 /* configuration for SBC8560 board */ +#define CONFIG_MPC8560 1 /* XXX flagging this as something I might want to delete */ #define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */ diff --git a/include/configs/scb9328.h b/include/configs/scb9328.h index d140241..4ae25ad 100644 --- a/include/configs/scb9328.h +++ b/include/configs/scb9328.h @@ -257,13 +257,9 @@ #define CFG_CS5L_VAL 0x00000D03 #define CONFIG_DRIVER_DM9000 1 -#define CONFIG_DRIVER_DM9000 1 #define CONFIG_DM9000_BASE 0x16000000 #define DM9000_IO CONFIG_DM9000_BASE #define DM9000_DATA (CONFIG_DM9000_BASE+4) -/* #define CONFIG_DM9000_USE_8BIT */ -#define CONFIG_DM9000_USE_16BIT -/* #define CONFIG_DM9000_USE_32BIT */ /* f_{dpll}=2*f{ref}*(MFI+MFN/(MFD+1))/(PD+1) f_ref=16,777MHz diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index 48251f3..f4eefae 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -34,11 +34,19 @@ /* This config file is used for Sequoia (440EPx) and Rainier (440GRx) */ #ifndef CONFIG_RAINIER #define CONFIG_440EPX 1 /* Specific PPC440EPx */ +#define CONFIG_HOSTNAME sequoia #else #define CONFIG_440GRX 1 /* Specific PPC440GRx */ +#define CONFIG_HOSTNAME rainier #endif #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + /* Detect Sequoia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ 33333333 : 33000000) @@ -64,19 +72,9 @@ * Base addresses -- Note these are effective addresses where the actual * resources get mapped (not physical addresses). */ -#ifndef CONFIG_VIDEO -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kiB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kiB for malloc() */ -#else -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */ -#endif - #define CFG_TLB_FOR_BOOT_FLASH 0x0003 #define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE #define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ #define CFG_OCM_BASE 0xe0010000 /* ocm */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE @@ -108,14 +106,9 @@ * Serial Port */ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /* * Environment */ @@ -227,10 +220,7 @@ /* * I2C */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -247,80 +237,27 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_RAINIER -#define CONFIG_HOSTNAME sequoia -#define CFG_BOOTFILE "bootfile=sequoia/uImage\0" -#define CFG_DTBFILE "fdt_file=sequoia/sequoia.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME rainier -#define CFG_BOOTFILE "bootfile=rainier/uImage\0" -#define CFG_DTBFILE "fdt_file=rainier/rainier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm\0" \ - "fdt_file=sequoia/sequoia.dtb\0" \ - "fdt_addr=400000\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm 200000 - ${fdt_addr}\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \ - "cp.b 200000 FFFA0000 60000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_HAS_ETH0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx */ - /* buffers & descriptors */ -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 1 @@ -347,35 +284,12 @@ #define CONFIG_ISO_PARTITION /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF #define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #ifdef CONFIG_440EPX @@ -407,35 +321,6 @@ #define CONFIG_SUPPORT_VFAT /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) - /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* * PCI stuff */ /* General PCI */ @@ -453,13 +338,6 @@ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* - * For booting Linux, the board info and command line data have to be in the - * first 8 MB of memory, since this is the maximum mapped by the Linux kernel - * during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* * External Bus Controller (EBC) Setup */ @@ -577,23 +455,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #ifdef CONFIG_VIDEO #define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */ #define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */ diff --git a/include/configs/sh7763rdp.h b/include/configs/sh7763rdp.h new file mode 100644 index 0000000..7713eaa --- /dev/null +++ b/include/configs/sh7763rdp.h @@ -0,0 +1,116 @@ +/* + * Configuation settings for the Renesas SH7763RDP board + * + * Copyright (C) 2008 Renesas Solutions Corp. + * Copyright (C) 2008 Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __SH7763RDP_H +#define __SH7763RDP_H + +#define CONFIG_SH 1 +#define CONFIG_SH4 1 +#define CONFIG_CPU_SH7763 1 +#define CONFIG_SH7763RDP 1 +#define __LITTLE_ENDIAN 1 + +/* + * Command line configuration. + */ +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_FLASH +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_ENV + +#define CONFIG_BOOTDELAY -1 +#define CONFIG_BOOTARGS "console=ttySC2,115200 root=1f01" +#define CONFIG_ENV_OVERWRITE 1 + +#define CONFIG_VERSION_VARIABLE +#undef CONFIG_SHOW_BOOT_PROGRESS + +/* SCIF */ +#define CFG_SCIF_CONSOLE 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_CONS_SCIF2 1 + +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Buffer size for input from the Console */ +#define CFG_PBSIZE 256 /* Buffer size for Console output */ +#define CFG_MAXARGS 16 /* max args accepted for monitor commands */ +#define CFG_BARGSIZE 512 /* Buffer size for Boot Arguments + passed to kernel */ +#define CFG_BAUDRATE_TABLE { 115200 } /* List of legal baudrate + settings for this board */ + +/* SDRAM */ +#define CFG_SDRAM_BASE (0x8C000000) +#define CFG_SDRAM_SIZE (64 * 1024 * 1024) +#define CFG_MEMTEST_START (CFG_SDRAM_BASE) +#define CFG_MEMTEST_END (CFG_MEMTEST_START + (60 * 1024 * 1024)) + +/* Flash(NOR) */ +#define CFG_FLASH_BASE (0xA0000000) +#define CFG_FLASH_CFI_WIDTH (FLASH_CFI_16BIT) +#define CFG_MAX_FLASH_BANKS (1) +#define CFG_MAX_FLASH_SECT (520) + +/* U-boot setting */ +#define CFG_LOAD_ADDR (CFG_SDRAM_BASE + 4 * 1024 * 1024) +#define CFG_MONITOR_BASE (CFG_FLASH_BASE) +#define CFG_MONITOR_LEN (128 * 1024) +/* Size of DRAM reserved for malloc() use */ +#define CFG_MALLOC_LEN (1024 * 1024) +/* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_SIZE (256) +#define CFG_BOOTMAPSZ (8 * 1024 * 1024) + +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#undef CFG_FLASH_QUIET_TEST +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +/* Timeout for Flash erase operations (in ms) */ +#define CFG_FLASH_ERASE_TOUT (3 * 1000) +/* Timeout for Flash write operations (in ms) */ +#define CFG_FLASH_WRITE_TOUT (3 * 1000) +/* Timeout for Flash set sector lock bit operations (in ms) */ +#define CFG_FLASH_LOCK_TOUT (3 * 1000) +/* Timeout for Flash clear lock bit operations (in ms) */ +#define CFG_FLASH_UNLOCK_TOUT (3 * 1000) +/* Use hardware flash sectors protection instead of U-Boot software protection */ +#undef CFG_FLASH_PROTECTION +#undef CFG_DIRECT_FLASH_TFTP +#define CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE (128 * 1024) +#define CFG_ENV_SIZE (CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR (CFG_FLASH_BASE + (1 * CFG_ENV_SECT_SIZE)) +/* Offset of env Flash sector relative to CFG_FLASH_BASE */ +#define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SECT_SIZE) +#define CFG_ENV_ADDR_REDUND (CFG_FLASH_BASE + (2 * CFG_ENV_SECT_SIZE)) + +/* Clock */ +#define CONFIG_SYS_CLK_FREQ 66666666 +#define TMU_CLK_DIVIDER (4) /* 4 (default), 16, 64, 256 or 1024 */ +#define CFG_HZ (CONFIG_SYS_CLK_FREQ / TMU_CLK_DIVIDER) + +#endif /* __SH7763RDP_H */ diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h index 4578cae..3e47eb8 100644 --- a/include/configs/smmaco4.h +++ b/include/configs/smmaco4.h @@ -42,6 +42,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/socrates.h b/include/configs/socrates.h index 23ed87f..1627413 100644 --- a/include/configs/socrates.h +++ b/include/configs/socrates.h @@ -165,7 +165,7 @@ #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256kB for Mon*/ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserved for malloc */ /* Serial Port */ @@ -216,18 +216,14 @@ #define CFG_EEPROM_PAGE_WRITE_ENABLE /* necessary for the LM75 chip */ #define CFG_EEPROM_PAGE_WRITE_BITS 4 -/* RapidIO MMU */ -#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ - /* * General PCI * Memory space is mapped 1-1. */ #define CFG_PCI_PHYS 0x80000000 /* 1G PCI TLB */ - +/* PCI is clocked by the external source at 33 MHz */ +#define CONFIG_PCI_CLK_FREQ 33000000 #define CFG_PCI1_MEM_BASE 0x80000000 #define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE #define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ @@ -237,13 +233,7 @@ #if defined(CONFIG_PCI) #define CONFIG_PCI_PNP /* do pci plug-and-play */ - -#define CONFIG_EEPRO100 -#undef CONFIG_TULIP - -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ - +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ #endif /* CONFIG_PCI */ @@ -389,10 +379,10 @@ "tftp ${fdt_addr_r} ${fdt_file}; " \ "run nfsargs addip addcons;" \ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "fdt_file=$hostname/socrates.dtb\0" \ + "fdt_file=$hostname/socrates.dtb\0" \ "fdt_addr_r=B00000\0" \ "fdt_addr=FC1E0000\0" \ - "rootpath=/opt/eldk/ppc_85xx\0" \ + "rootpath=/opt/eldk/ppc_85xxDP\0" \ "kernel_addr=FC000000\0" \ "kernel_addr_r=200000\0" \ "ramdisk_addr=FC200000\0" \ @@ -419,4 +409,14 @@ #define CONFIG_DOS_PARTITION 1 #define CONFIG_USB_STORAGE 1 +/* FPGA and NAND */ +#define CFG_FPGA_BASE 0xc0000000 +#define CFG_BR3_PRELIM 0xc0001881 /* UPMA, 32-bit */ +#define CFG_OR3_PRELIM 0xfff00000 /* 1 MB */ + +#define CFG_NAND_BASE (CFG_FPGA_BASE + 0x70) +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_MAX_CHIPS 1 +#define CONFIG_CMD_NAND + #endif /* __CONFIG_H */ diff --git a/include/configs/sorcery.h b/include/configs/sorcery.h index c62b977..18f5533 100644 --- a/include/configs/sorcery.h +++ b/include/configs/sorcery.h @@ -31,6 +31,8 @@ #define CONFIG_MPC8220 1 #define CONFIG_SORCERY 1 /* Sorcery board */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* Input clock running at 60Mhz, read Hid1 for the CPU multiplier to determine the CPU speed. */ #define CFG_MPC8220_CLKIN 60000000 /* ... running at 60MHz */ diff --git a/include/configs/spieval.h b/include/configs/spieval.h index 49213dc..69d2d67 100644 --- a/include/configs/spieval.h +++ b/include/configs/spieval.h @@ -44,6 +44,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index ec04a30..6e8213d 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -41,6 +41,7 @@ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ +#define CONFIG_MPC8560 1 #undef CONFIG_PCI /* pci ethernet support */ #define CONFIG_TSEC_ENET /* tsec ethernet support*/ diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h index d033c86..a1e9789 100644 --- a/include/configs/stxssa.h +++ b/include/configs/stxssa.h @@ -41,6 +41,7 @@ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ #define CONFIG_CPM2 1 /* has CPM2 */ #define CONFIG_STXSSA 1 /* Silicon Tx GPPP SSA board specific*/ +#define CONFIG_MPC8560 1 #define CONFIG_PCI /* PCI ethernet support */ #define CONFIG_TSEC_ENET /* tsec ethernet support*/ diff --git a/include/configs/stxxtc.h b/include/configs/stxxtc.h index 97a1032..fcafba5 100644 --- a/include/configs/stxxtc.h +++ b/include/configs/stxxtc.h @@ -590,8 +590,8 @@ typedef unsigned int led_id_t; /*****************************************************************************/ -/* pass open firmware flat tree */ -#define CONFIG_OF_FLAT_TREE 1 +/* pass open firmware flattened device tree */ +#define CONFIG_OF_LIBFDT 1 #define OF_CPU "PowerPC,MPC870@0" #define OF_TBCLK (MPC8XX_HZ / 16) diff --git a/include/configs/taihu.h b/include/configs/taihu.h index c060b1e..86f776d 100644 --- a/include/configs/taihu.h +++ b/include/configs/taihu.h @@ -32,6 +32,12 @@ #define CONFIG_4xx 1 /* member of PPC4xx family */ #define CONFIG_TAIHU 1 /* on a taihu board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taihu +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */ @@ -70,87 +76,31 @@ #define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ -#define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS -#define CONFIG_EXTRA_ENV_SETTINGS \ - "bootfile=/tftpboot/taihu/uImage\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "netdev=eth0\0" \ - "hostname=taihu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=FC000000\0" \ "ramdisk_addr=FC180000\0" \ - "load=tftp 200000 /tftpboot/taihu/u-boot.bin\0" \ - "update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;" \ - "cp.b 200000 FFFC0000 40000\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x14 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 0x10 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_PHY_RESET 1 /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SPI -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #undef CONFIG_SPD_EEPROM /* use SPD EEPROM for setup */ #define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */ #define CFG_SDRAM_BANKS 2 @@ -169,23 +119,6 @@ #define CFG_SDRAM_tRFC 66 /* Auto refresh period */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -198,35 +131,13 @@ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 - -#define CONFIG_BAUDRATE 115200 - #define CONFIG_UART1_CONSOLE 1 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -278,25 +189,12 @@ unsigned char spi_read(void); /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFE00000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ - #define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ @@ -421,21 +319,5 @@ unsigned char spi_read(void); #define CPLD_REG0_ADDR 0x50100000 #define CPLD_REG1_ADDR 0x50100001 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 #endif /* __CONFIG_H */ diff --git a/include/configs/taishan.h b/include/configs/taishan.h index 1879d38..ba42192 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -32,9 +32,15 @@ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taishan +#define CONFIG_USE_TTY ttyS1 +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -42,9 +48,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -70,19 +74,11 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */ -#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */ #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * Environment @@ -138,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #undef CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR 0x50 @@ -159,65 +152,23 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=taishan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/taishan/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \ "kozio=bootm 0xffe00000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x1 @@ -230,70 +181,12 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * PCI stuff @@ -312,28 +205,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/tb0229.h b/include/configs/tb0229.h index dadf5d3..fc2357d 100644 --- a/include/configs/tb0229.h +++ b/include/configs/tb0229.h @@ -122,7 +122,9 @@ #define CFG_BOOTPARAMS_LEN 128*1024 -#define CFG_HZ (CPU_TCLOCK_RATE/4) +#define CFG_MIPS_TIMER_FREQ (CPU_TCLOCK_RATE/4) + +#define CFG_HZ 1000 #define CFG_SDRAM_BASE 0x80000000 diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h index 25155ad..f77dd14 100644 --- a/include/configs/trizepsiv.h +++ b/include/configs/trizepsiv.h @@ -276,13 +276,9 @@ #define CFG_MCIO1_VAL 0x0000c108 #define CONFIG_DRIVER_DM9000 1 -#define CONFIG_DRIVER_DM9000 1 #define CONFIG_DM9000_BASE 0x08000000 #define DM9000_IO CONFIG_DM9000_BASE #define DM9000_DATA (CONFIG_DM9000_BASE+0x8004) -/* #define CONFIG_DM9000_USE_8BIT */ -/* #define CONFIG_DM9000_USE_16BIT */ -#define CONFIG_DM9000_USE_32BIT #define CONFIG_USB_OHCI_NEW 1 #define CFG_USB_OHCI_BOARD_INIT 1 diff --git a/include/configs/uc101.h b/include/configs/uc101.h index dc1d7e1..042750e 100644 --- a/include/configs/uc101.h +++ b/include/configs/uc101.h @@ -40,6 +40,8 @@ #define CONFIG_BOARD_EARLY_INIT_R +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/v38b.h b/include/configs/v38b.h index e24d6f7..c203522 100644 --- a/include/configs/v38b.h +++ b/include/configs/v38b.h @@ -46,6 +46,8 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ +#define CONFIG_HIGH_BATS 1 /* High BATs supported */ + /* * Serial console configuration */ diff --git a/include/configs/walnut.h b/include/configs/walnut.h index adc420b..e19c5f3 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -38,122 +38,44 @@ #define CONFIG_WALNUT 1 /* ...on a WALNUT board */ /* ...and on a SYCAMORE board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME walnut +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=walnut\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/walnut/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff80000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ - -#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -167,29 +89,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -224,13 +128,8 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) /* * Define here the location of the environment variables (FLASH or NVRAM). @@ -243,13 +142,6 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * FLASH organization */ @@ -335,21 +227,4 @@ */ #define SPD_EEPROM_ADDRESS 0x50 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h index f22e798..891b515 100644 --- a/include/configs/yosemite.h +++ b/include/configs/yosemite.h @@ -42,6 +42,11 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ #define CONFIG_BOARD_RESET 1 /* call board_reset() */ @@ -50,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +85,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -142,10 +138,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -167,72 +160,22 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifndef CONFIG_YELLOWSTONE -#define CONFIG_HOSTNAME yosemite -#define CFG_BOOTFILE "bootfile=/tftpboot/yosemite/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME yellowstone -#define CFG_BOOTFILE "bootfile=/tftpboot/yellowstone/uImage\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "bootfile=/tftpboot/${hostname}/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0" \ - "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ - "cp.b 200000 fff80000 80000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ -#define CONFIG_PHY1_ADDR 3 #define CONFIG_HAS_ETH0 1 /* add support for "ethaddr" */ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ - -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_PHY1_ADDR 3 /* Partitions */ #define CONFIG_MAC_PARTITION @@ -263,36 +206,11 @@ #define CONFIG_HW_WATCHDOG /* watchdog */ #endif - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO -#define CONFIG_CMD_SDRAM #ifdef CONFIG_440EP #define CONFIG_CMD_USB @@ -300,36 +218,6 @@ #define CONFIG_CMD_EXT2 #endif - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -347,13 +235,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -370,21 +251,4 @@ #define CFG_BCSR5_PCI66EN 0x80 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 6f9d3e3..026fef6 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -38,13 +38,18 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* Disable-takes long time */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ #define EXTCLK_33_33 33333333 #define EXTCLK_66_66 66666666 #define EXTCLK_50 50000000 #define EXTCLK_83 83333333 +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME yucca +#include "amcc-common.h" + #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ #undef CONFIG_SHOW_BOOT_PROGRESS #undef CONFIG_STRESS @@ -53,9 +58,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffb0000 /* start of monitor */ #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -99,24 +102,15 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Mon */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CONFIG_SERIAL_SOFTWARE_FIFO #undef CFG_EXT_SERIAL_CLOCK /* #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) */ /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ @@ -127,10 +121,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define IIC0_BOOTPROM_ADDR 0x50 #define IIC0_ALT_BOOTPROM_ADDR 0x54 @@ -153,123 +144,32 @@ #undef CFG_ENV_IS_IN_EEPROM /* ... not in EEPROM */ #define CONFIG_ENV_OVERWRITE 1 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=yucca\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=yucca/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=E7F10000\0" \ "ramdisk_addr=E7F20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 yuca/u-boot.bin\0" \ - "update=protect off 2:4-7;era 2:4-7;" \ - "cp.b ${fileaddr} FFFB0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:EP:EP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM - #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ -#undef CONFIG_NET_MULTI #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * FLASH related @@ -318,26 +218,6 @@ /* Support for Intel 82557/82559/82559ER chips. */ #define CONFIG_EEPRO100 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /* FB Divisor selection */ #define FPGA_FB_DIV_6 6 #define FPGA_FB_DIV_10 10 @@ -539,10 +419,4 @@ #define PERIOD_33_33MHZ 30000 /* 30ns */ #define PERIOD_25_00MHZ 40000 /* 40ns */ -/*---------------------------------------------------------------------------*/ - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ |