diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/MPC8540ADS.h | 10 | ||||
| -rw-r--r-- | include/configs/MPC8541CDS.h | 13 | ||||
| -rw-r--r-- | include/configs/MPC8548CDS.h | 521 | ||||
| -rw-r--r-- | include/configs/MPC8555CDS.h | 13 | ||||
| -rw-r--r-- | include/configs/MPC8560ADS.h | 10 | ||||
| -rw-r--r-- | include/configs/PM854.h | 10 | ||||
| -rw-r--r-- | include/configs/SBC8540.h | 12 | ||||
| -rw-r--r-- | include/configs/SBC8560.h | 12 | ||||
| -rw-r--r-- | include/configs/TQM8540.h | 6 | ||||
| -rw-r--r-- | include/configs/TQM8560.h | 3 | ||||
| -rw-r--r-- | include/configs/sbc8560.h | 12 | ||||
| -rw-r--r-- | include/configs/stxgp3.h | 4 |
12 files changed, 599 insertions, 27 deletions
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h index 533b587..131c832 100644 --- a/include/configs/MPC8540ADS.h +++ b/include/configs/MPC8540ADS.h @@ -49,10 +49,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -342,7 +344,9 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 @@ -351,11 +355,13 @@ #if CONFIG_HAS_FEC #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 3 #define FEC_PHYIDX 0 #endif -#define CONFIG_ETHPRIME "MOTO ENET0" +/* Options are: TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h index 3ec27b8..c96b98b 100644 --- a/include/configs/MPC8541CDS.h +++ b/include/configs/MPC8541CDS.h @@ -41,9 +41,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * When initializing flash, if we cannot find the manufacturer ID, @@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h new file mode 100644 index 0000000..4ca8bc3 --- /dev/null +++ b/include/configs/MPC8548CDS.h @@ -0,0 +1,521 @@ +/* + * Copyright 2004 Freescale Semiconductor. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * mpc8548cds board configuration file + * + * Please refer to doc/README.mpc85xxcds for more info. + * + */ +#ifndef __CONFIG_H +#define __CONFIG_H + +/* High Level Configuration Options */ +#define CONFIG_BOOKE 1 /* BOOKE */ +#define CONFIG_E500 1 /* BOOKE e500 family */ +#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ +#define CONFIG_MPC8548 1 /* MPC8548 specific */ +#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */ + +#undef CONFIG_PCI +#define CONFIG_TSEC_ENET /* tsec ethernet support */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ +#define CONFIG_DDR_DLL /* possible DLL fix needed */ +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + + +/* + * When initializing flash, if we cannot find the manufacturer ID, + * assume this is the AMD flash associated with the CDS board. + * This allows booting from a promjet. + */ +#define CONFIG_ASSUME_AMD_FLASH + +#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */ + +#ifndef __ASSEMBLY__ +extern unsigned long get_clock_freq(void); +#endif +#define CONFIG_SYS_CLK_FREQ get_clock_freq() /* sysclk for MPC85xx */ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ + +/* + * Only possible on E500 Version 2 or newer cores. + */ +#define CONFIG_ENABLE_36BIT_PHYS 1 + + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ + +#undef CFG_DRAM_TEST /* memory test, takes time */ +#define CFG_MEMTEST_START 0x00200000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00400000 + +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */ +#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ + +/* + * DDR Setup + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */ + +/* + * Make sure required options are set + */ +#ifndef CONFIG_SPD_EEPROM +#error ("CONFIG_SPD_EEPROM is required") +#endif + +#undef CONFIG_CLOCKS_IN_MHZ + + +/* + * Local Bus Definitions + */ + +/* + * FLASH on the Local Bus + * Two banks, 8M each, using the CFI driver. + * Boot from BR0/OR0 bank at 0xff00_0000 + * Alternate BR1/OR1 bank at 0xff80_0000 + * + * BR0, BR1: + * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0 + * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0 + * Port Size = 16 bits = BRx[19:20] = 10 + * Use GPCM = BRx[24:26] = 000 + * Valid = BRx[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0 + * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1 + * + * OR0, OR1: + * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0 + * Reserved ORx[17:18] = 11, confusion here? + * CSNT = ORx[20] = 1 + * ACS = half cycle delay = ORx[21:22] = 11 + * SCY = 6 = ORx[24:27] = 0110 + * TRLX = use relaxed timing = ORx[29] = 1 + * EAD = use external address latch delay = OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx + */ + +#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */ + +#define CFG_BR0_PRELIM 0xff801001 +#define CFG_BR1_PRELIM 0xff001001 + +#define CFG_OR0_PRELIM 0xff806e65 +#define CFG_OR1_PRELIM 0xff806e65 + +#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_SECT 128 /* sectors per device */ +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ + +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_CFI +#define CFG_FLASH_EMPTY_INFO + + +/* + * SDRAM on the Local Bus + */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + +/* + * Base Register 2 and Option Register 2 configure SDRAM. + * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000. + * + * For BR2, need: + * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0 + * port-size = 32-bits = BR2[19:20] = 11 + * no parity checking = BR2[21:22] = 00 + * SDRAM for MSEL = BR2[24:26] = 011 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861 + * + * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into + * FIXME: the top 17 bits of BR2. + */ + +#define CFG_BR2_PRELIM 0xf0001861 + +/* + * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64. + * + * For OR2, need: + * 64MB mask for AM, OR2[0:7] = 1111 1100 + * XAM, OR2[17:18] = 11 + * 9 columns OR2[19-21] = 010 + * 13 rows OR2[23-25] = 100 + * EAD set for extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901 + */ + +#define CFG_OR2_PRELIM 0xfc006901 + +#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */ +#define CFG_LBC_LBCR 0x00000000 /* LB config reg */ +#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */ +#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/ + +/* + * LSDMR masks + */ +#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1)) +#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10)) +#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10)) +#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16)) +#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19)) +#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22)) +#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22)) +#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23)) +#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27)) +#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31)) + +#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4)) +#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4)) + +/* + * Common settings for all Local Bus SDRAM commands. + * At run time, either BSMA1516 (for CPU 1.1) + * or BSMA1617 (for CPU 1.0) (old) + * is OR'ed in too. + */ +#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_RFCR16 \ + | CFG_LBC_LSDMR_PRETOACT7 \ + | CFG_LBC_LSDMR_ACTTORW7 \ + | CFG_LBC_LSDMR_BL8 \ + | CFG_LBC_LSDMR_WRC4 \ + | CFG_LBC_LSDMR_CL3 \ + | CFG_LBC_LSDMR_RFEN \ + ) + +/* + * The CADMUS registers are connected to CS3 on CDS. + * The new memory map places CADMUS at 0xf8000000. + * + * For BR3, need: + * Base address of 0xf8000000 = BR[0:16] = 1111 1000 0000 0000 0 + * port-size = 8-bits = BR[19:20] = 01 + * no parity checking = BR[21:22] = 00 + * GPMC for MSEL = BR[24:26] = 000 + * Valid = BR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1000 0000 0000 0000 1000 0000 0001 = f8000801 + * + * For OR3, need: + * 1 MB mask for AM, OR[0:16] = 1111 1111 1111 0000 0 + * disable buffer ctrl OR[19] = 0 + * CSNT OR[20] = 1 + * ACS OR[21:22] = 11 + * XACS OR[23] = 1 + * SCY 15 wait states OR[24:27] = 1111 max is suboptimal but safe + * SETA OR[28] = 0 + * TRLX OR[29] = 1 + * EHTR OR[30] = 1 + * EAD extra time OR[31] = 1 + * + * 0 4 8 12 16 20 24 28 + * 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7 + */ + +#define CADMUS_BASE_ADDR 0xf8000000 +#define CFG_BR3_PRELIM 0xf8000801 +#define CFG_OR3_PRELIM 0xfff00ff7 + +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 2 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE 1 +#define CFG_NS16550_CLK get_bus_freq(0) + +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} + +#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) +#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) + +/* Use the HUSH parser */ +#define CFG_HUSH_PARSER +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT_HUSH_PS2 "> " +#endif + +/* I2C */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ + +/* + * General PCI + * Addresses are mapped 1-1. + */ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#define CFG_PCI2_MEM_BASE 0xa0000000 +#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE +#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI2_IO_BASE 0xe3000000 +#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE +#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ + + +#if defined(CONFIG_PCI) + +#define CONFIG_NET_MULTI +#define CONFIG_PCI_PNP /* do pci plug-and-play */ + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) + #define PCI_ENET0_IOADDR 0xe0000000 + #define PCI_ENET0_MEMADDR 0xe0000000 + #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/ +#endif + +#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif + +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "eTSEC0" +#define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1" +#define CONFIG_MPC85XX_TSEC3 1 +#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC2" +#define CONFIG_MPC85XX_TSEC4 1 +#define CONFIG_MPC85XX_TSEC4_NAME "eTSEC3" +#undef CONFIG_MPC85XX_FEC + +#define TSEC1_PHY_ADDR 0 +#define TSEC2_PHY_ADDR 1 +#define TSEC3_PHY_ADDR 2 +#define TSEC4_PHY_ADDR 3 +#define FEC_PHY_ADDR 3 + +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC3_PHYIDX 0 +#define TSEC4_PHYIDX 0 +#define FEC_PHYIDX 0 + +/* Options are: eTSEC[0-3] */ +#define CONFIG_ETHPRIME "eTSEC0" + +#endif /* CONFIG_TSEC_ENET */ + +/* + * Environment + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ +#define CFG_ENV_SIZE 0x2000 + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#if defined(CONFIG_PCI) +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PCI \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII) +#else +#define CONFIG_COMMANDS (CONFIG_CMD_DFL \ + | CFG_CMD_PING \ + | CFG_CMD_I2C \ + | CFG_CMD_MII) +#endif +#include <cmd_confdefs.h> + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_LOAD_ADDR 0x2000000 /* default load address */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ + +/* Cache Configuration */ +#define CFG_DCACHE_SIZE 32768 +#define CFG_CACHELINE_SIZE 32 +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Environment Configuration + */ + +/* The mac addresses for all ethernet interface */ +#if defined(CONFIG_TSEC_ENET) +#define CONFIG_ETHADDR 00:E0:0C:00:00:FD +#define CONFIG_HAS_ETH1 +#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD +#define CONFIG_HAS_ETH2 +#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD +#endif + +#define CONFIG_IPADDR 192.168.1.253 + +#define CONFIG_HOSTNAME unknown +#define CONFIG_ROOTPATH /nfsroot +#define CONFIG_BOOTFILE your.uImage + +#define CONFIG_SERVERIP 192.168.1.1 +#define CONFIG_GATEWAYIP 192.168.1.1 +#define CONFIG_NETMASK 255.255.255.0 + +#define CONFIG_LOADADDR 200000 /*default location for tftp and bootm*/ + +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */ +#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/ + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS1\0" \ + "ramdiskaddr=400000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr" + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "bootm $loadaddr $ramdiskaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND + +#endif /* __CONFIG_H */ diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h index 7967e90..a44e3ec 100644 --- a/include/configs/MPC8555CDS.h +++ b/include/configs/MPC8555CDS.h @@ -41,9 +41,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * When initializing flash, if we cannot find the manufacturer ID, @@ -360,7 +363,9 @@ extern unsigned long get_clock_freq(void); #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 @@ -368,7 +373,9 @@ extern unsigned long get_clock_freq(void); #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index e1a2bba..db878cb 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -46,10 +46,12 @@ #undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -337,13 +339,17 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPC85XX_FEC #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/PM854.h b/include/configs/PM854.h index 69e1baf..12a7181 100644 --- a/include/configs/PM854.h +++ b/include/configs/PM854.h @@ -45,10 +45,12 @@ #define CONFIG_TSEC_ENET /* tsec ethernet support */ #define CONFIG_ENV_OVERWRITE #undef CONFIG_SPD_EEPROM /* do not use SPD EEPROM for DDR setup*/ -#define CONFIG_DDR_ECC /* only for ECC DDR module */ #define CONFIG_DDR_DLL /* possible DLL fix needed */ #define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ +#define CONFIG_DDR_ECC /* only for ECC DDR module */ +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef + /* * sysclk for MPC85xx @@ -250,17 +252,21 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 3 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 1 #define FEC_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #define CONFIG_HAS_ETH1 1 #define CONFIG_HAS_ETH2 1 diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h index 5bdabfe..0451b20 100644 --- a/include/configs/SBC8540.h +++ b/include/configs/SBC8540.h @@ -227,10 +227,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define CONFIG_MII 1 /* MII PHY management */ +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/SBC8560.h b/include/configs/SBC8560.h index ca7e5dd..8b46a17 100644 --- a/include/configs/SBC8560.h +++ b/include/configs/SBC8560.h @@ -215,10 +215,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 /* MII PHY management */ +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/TQM8540.h b/include/configs/TQM8540.h index 9dc77c4..8438b93 100644 --- a/include/configs/TQM8540.h +++ b/include/configs/TQM8540.h @@ -280,20 +280,24 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC1_PHY_ADDR 0 #define TSEC2_PHY_ADDR 1 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 #define CONFIG_MPC85XX_FEC 1 +#define CONFIG_MPC85XX_FEC_NAME "FEC" #define FEC_PHY_ADDR 2 #define FEC_PHYIDX 0 #define CONFIG_HAS_ETH1 #define CONFIG_HAS_ETH2 -#define CONFIG_ETHPRIME "ENET1" +/* Options are TSEC[0-1], FEC */ +#define CONFIG_ETHPRIME "TSEC1" #endif /* CONFIG_TSEC_ENET */ diff --git a/include/configs/TQM8560.h b/include/configs/TQM8560.h index f418e26..1466f31 100644 --- a/include/configs/TQM8560.h +++ b/include/configs/TQM8560.h @@ -276,6 +276,7 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #define TSEC2_PHY_ADDR 1 #define TSEC2_PHYIDX 0 @@ -288,7 +289,7 @@ #define CFG_CPMFCR_RAMTYPE 0 #define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) -#define CONFIG_ETHPRIME "ENET1" +#define CONFIG_ETHPRIME "TSEC1" /* * Environment diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 72a3091..5a434dc 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -210,10 +210,14 @@ #if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ - #define CONFIG_NET_MULTI 1 - #define CONFIG_PHY_BCM5421S 1 /* GigaBit Ether PHY */ - #define CONFIG_MII 1 /* MII PHY management */ - #define CONFIG_PHY_ADDR 25 /* PHY address */ +# define CONFIG_NET_MULTI 1 +# define CONFIG_MII 1 /* MII PHY management */ +# define CONFIG_MPC85xx_TSEC1 +# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" +# define TSEC1_PHY_ADDR 25 +# define TSEC1_PHYIDX 0 +/* Options are: TSEC0 */ +# define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index b5684d3..e218597 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -227,14 +227,16 @@ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0" #define CONFIG_MPC85XX_TSEC2 1 +#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1" #undef CONFIG_MPS85XX_FEC #define TSEC1_PHY_ADDR 2 #define TSEC2_PHY_ADDR 4 #define TSEC1_PHYIDX 0 #define TSEC2_PHYIDX 0 -#define CONFIG_ETHPRIME "MOTO ENET0" +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ |