diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/acadia.h | 169 | ||||
| -rw-r--r-- | include/configs/bamboo.h | 168 | ||||
| -rw-r--r-- | include/configs/bubinga.h | 150 | ||||
| -rw-r--r-- | include/configs/canyonlands.h | 173 | ||||
| -rw-r--r-- | include/configs/ebony.h | 151 | ||||
| -rw-r--r-- | include/configs/katmai.h | 162 | ||||
| -rw-r--r-- | include/configs/kilauea.h | 160 | ||||
| -rw-r--r-- | include/configs/luan.h | 147 | ||||
| -rw-r--r-- | include/configs/makalu.h | 158 |
9 files changed, 140 insertions, 1298 deletions
diff --git a/include/configs/acadia.h b/include/configs/acadia.h index bbf726d..9092a7c 100644 --- a/include/configs/acadia.h +++ b/include/configs/acadia.h @@ -34,6 +34,13 @@ #define CONFIG_ACADIA 1 /* Board is Acadia */ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_405EZ 1 /* Specifc 405EZ support*/ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME acadia +#include "amcc-common.h" + /* Detect Acadia PLL input clock automatically via CPLD bit */ #define CONFIG_SYS_CLK_FREQ ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \ 66666666 : 33333000) @@ -59,16 +66,11 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xfe000000 #define CFG_CPLD_BASE 0x80000000 #define CFG_NAND_ADDR 0xd0000000 #define CFG_USB_HOST 0xef603000 /* USB OHCI 1.1 controller */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024)/* Reserve 512 kB for malloc() */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer *----------------------------------------------------------------------*/ @@ -89,12 +91,6 @@ *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ #define CFG_BASE_BAUD 691200 -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 - -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Environment @@ -202,10 +198,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -222,77 +215,24 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -#if 0 /* test-only... */ -/*----------------------------------------------------------------------- - * SPI stuff - Define to include SPI control - *----------------------------------------------------------------------- - */ -#define CONFIG_SPI -#endif - /*----------------------------------------------------------------------- * Ethernet *----------------------------------------------------------------------*/ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* # of rx buffers & descriptors*/ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NETCONSOLE /* include NetConsole support */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=acadia\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=acadia/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 acadia/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 acadia/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "kozio=bootm ffc60000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_USB_OHCI #define CONFIG_USB_STORAGE @@ -305,35 +245,10 @@ #define CONFIG_SUPPORT_VFAT /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS -#define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_USB /* @@ -344,43 +259,6 @@ #undef CONFIG_CMD_IMLS #endif -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ @@ -493,21 +371,4 @@ #define CFG_GPIO1_TSRL 0x00000000 #define CFG_GPIO1_TSRH 0x00000000 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ - #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h index 8d77164..41058f8 100644 --- a/include/configs/bamboo.h +++ b/include/configs/bamboo.h @@ -36,6 +36,12 @@ #define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bamboo +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* @@ -49,10 +55,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfff00000 /* start of FLASH */ #define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ #define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 @@ -84,14 +86,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * NVRAM/RTC * @@ -227,10 +224,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -244,54 +238,20 @@ #define CFG_ENV_OFFSET 0x0 #endif /* CFG_ENV_IS_IN_EEPROM */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bamboo\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bamboo/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fff00000\0" \ "ramdisk_addr=fff10000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b 100000 fffa0000 60000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 @@ -299,16 +259,6 @@ #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #endif /* CONFIG_BAMBOO_NAND */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION -#define CONFIG_ISO_PARTITION - #ifdef CONFIG_440EP /* USB */ #define CONFIG_USB_OHCI @@ -318,77 +268,27 @@ #define USB_2_0_DEVICE #endif /*CONFIG_440EP*/ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT2 #define CONFIG_CMD_SNTP +#define CONFIG_CMD_USB #ifdef CONFIG_BAMBOO_NAND #define CONFIG_CMD_NAND #endif - #define CONFIG_SUPPORT_VFAT -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- * PCI stuff @@ -407,28 +307,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h index 75dd4e7..acce82f 100644 --- a/include/configs/bubinga.h +++ b/include/configs/bubinga.h @@ -37,6 +37,12 @@ #define CONFIG_4xx 1 /* ...member of PPC4xx family */ #define CONFIG_BUBINGA 1 /* ...on a BUBINGA board */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME bubinga +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ @@ -80,118 +86,35 @@ #define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */ #endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=bubinga\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/bubinga/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff80000\0" \ "ramdisk_addr=fff90000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run net_nfs" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 2 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ #define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Bubinga */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_CACHE #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -/* * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. * If CFG_405_UART_ERRATA_59, then UART divisor is 31. * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. @@ -205,29 +128,11 @@ #undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ #define CFG_BASE_BAUD 691200 -/* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_NOPROBES { 0x69 } /* avoid iprobe hangup (why?) */ #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ @@ -272,21 +177,9 @@ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_SRAM_BASE 0xFFF00000 #define CFG_FLASH_BASE 0xFFF80000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization @@ -423,21 +316,4 @@ #define FPGA_REG1_OFFB_FLASH 0x02 /* Off board flash */ #define FPGA_REG1_SRAM_BOOT 0x01 /* SRAM at 0xFFF80000 not Flash */ -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h index 3dd577a..ac2e5d9 100644 --- a/include/configs/canyonlands.h +++ b/include/configs/canyonlands.h @@ -30,12 +30,19 @@ /* This config file is used for Canyonlands (460EX) and Glacier (460GT) */ #ifndef CONFIG_CANYONLANDS #define CONFIG_460GT 1 /* Specific PPC460GT */ +#define CONFIG_HOSTNAME glacier #else #define CONFIG_460EX 1 /* Specific PPC460EX */ +#define CONFIG_HOSTNAME canyonlands #endif #define CONFIG_440 1 #define CONFIG_4xx 1 /* ... PPC4xx family */ +/* + * Include common defines/options for all AMCC eval boards + */ +#include "amcc-common.h" + #define CONFIG_SYS_CLK_FREQ 66666667 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ @@ -47,8 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ - #define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ #define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ #define CFG_PCI_TARGBASE CFG_PCI_MEMBASE @@ -86,10 +91,6 @@ #define CFG_AHB_BASE 0xE2000000 /* internal AHB peripherals */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc()*/ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in OCM) *----------------------------------------------------------------------*/ @@ -102,13 +103,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE /* define this if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -242,10 +238,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CFG_I2C_SPEED 400000 /* I2C speed */ #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -270,7 +263,6 @@ * Ethernet *----------------------------------------------------------------------*/ #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address, See schematics */ #define CONFIG_PHY1_ADDR 1 #define CONFIG_HAS_ETH0 @@ -282,14 +274,11 @@ #define CONFIG_HAS_ETH2 #define CONFIG_HAS_ETH3 #endif -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_DYNAMIC_ANEG 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - /*----------------------------------------------------------------------- * USB-OHCI *----------------------------------------------------------------------*/ @@ -305,104 +294,30 @@ #define CFG_USB_OHCI_MAX_ROOT_PORTS 15 #endif -/*----------------------------------------------------------------------- - * Default environment - *----------------------------------------------------------------------*/ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -/* Setup some board specific values for the default environment variables */ -#ifdef CONFIG_CANYONLANDS -#define CONFIG_HOSTNAME canyonlands -#define CFG_BOOTFILE "bootfile=canyonlands/uImage\0" -#define CFG_DTBFILE "fdt_file=canyonlands/canyonlands.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" -#else -#define CONFIG_HOSTNAME glacier -#define CFG_BOOTFILE "bootfile=glacier/uImage\0" -#define CFG_DTBFILE "fdt_file=glacier/glacier.dtb\0" -#define CFG_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" -#endif - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - CFG_BOOTFILE \ - CFG_DTBFILE \ - CFG_ROOTPATH \ - "netdev=eth0\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 ${hostname}/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 ${hostname}/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 100000;nand write 200000 0 100000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP #define CONFIG_CMD_DTT -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM +#define CONFIG_CMD_SNTP #ifdef CONFIG_460EX #define CONFIG_CMD_EXT2 #define CONFIG_CMD_FAT @@ -415,41 +330,6 @@ #define CONFIG_ISO_PARTITION /*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - -#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#endif - -/*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ /* General PCI */ @@ -465,21 +345,6 @@ #define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -671,8 +536,4 @@ } #endif -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/ebony.h b/include/configs/ebony.h index b41fa17..df444d8 100644 --- a/include/configs/ebony.h +++ b/include/configs/ebony.h @@ -38,6 +38,12 @@ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ /* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME ebony +#include "amcc-common.h" + +/* * Define here the location of the environment variables (FLASH or NVRAM). * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only * supported for backward compatibility. @@ -54,7 +60,6 @@ *----------------------------------------------------------------------*/ #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff800000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -73,18 +78,11 @@ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400} /*----------------------------------------------------------------------- * NVRAM/RTC @@ -140,10 +138,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -152,125 +147,31 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=ebony\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/ebony/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=ff800000\0" \ "ramdisk_addr=ff810000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/ebony/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 8 /* PHY address */ #define CONFIG_HAS_ETH0 #define CONFIG_HAS_ETH1 #define CONFIG_PHY1_ADDR 9 /* EMAC1 PHY address */ -#define CONFIG_NET_MULTI 1 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -287,28 +188,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/katmai.h b/include/configs/katmai.h index 3c81862..d3789bd 100644 --- a/include/configs/katmai.h +++ b/include/configs/katmai.h @@ -38,6 +38,13 @@ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_440SPE 1 /* Specifc SPe support */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME katmai +#include "amcc-common.h" #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ @@ -47,7 +54,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ #define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ @@ -77,10 +83,6 @@ #define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ -#define CFG_MONITOR_BASE TEXT_BASE -#define CFG_MONITOR_LEN (0xFFFFFFFF - CFG_MONITOR_BASE + 1) -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ - /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ @@ -97,12 +99,8 @@ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CONFIG_SERIAL_MULTI 1 #undef CONFIG_UART1_CONSOLE #undef CFG_EXT_SERIAL_CLOCK -#define CONFIG_BAUDRATE 115200 -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * DDR SDRAM @@ -116,10 +114,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CONFIG_I2C_MULTI_BUS #define CONFIG_I2C_CMD_TREE @@ -171,139 +166,36 @@ *----------------------------------------------------------------------*/ #define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define xstr(s) str(s) -#define str(s) #s - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=katmai\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "net_nfs_fdt=tftp 200000 ${bootfile};" \ - "tftp ${fdt_addr} ${fdt_file};" \ - "run nfsargs addip addtty;" \ - "bootm 200000 - ${fdt_addr}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=katmai/uImage\0" \ - "fdt_file=katmai/katmai.dtb\0" \ - "fdt_addr=400000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fff10000\0" \ "ramdisk_addr=fff20000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 katmai/u-boot.bin\0" \ - "update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;" \ - "cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "kozio=bootm ffc60000\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_EEPROM #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM #define CONFIG_CMD_SNTP #define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_HAS_ETH0 #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ - -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * FLASH related @@ -435,28 +327,4 @@ #define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) #define CFG_GPIO_ODR 0 -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 205577f..9c1a3a4 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -39,6 +39,12 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME kilauea +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ #define CONFIG_BOARD_EMAC_COUNT @@ -47,14 +53,10 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_NAND_ADDR 0xF8000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -112,14 +114,9 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -273,9 +270,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -295,7 +290,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -303,102 +297,33 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 2 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ + CONFIG_AMCC_DEF_ENV_NAND_UPD \ "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=kilauea\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "flash_self_old=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=kilauea/uImage\0" \ - "fdt_file=kilauea/kilauea.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 kilauea/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \ - "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \ - "setenv filesize;saveenv\0" \ - "nupd=run nload nupdate\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG -#define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII #define CONFIG_CMD_NAND -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ @@ -417,37 +342,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -476,13 +370,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -556,19 +443,6 @@ } \ } -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - /*----------------------------------------------------------------------- * Some Kilauea stuff..., mainly fpga registers */ @@ -604,8 +478,4 @@ #define CFG_FPGA_USER_LED0 0x00000200 #define CFG_FPGA_USER_LED1 0x00000100 -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/luan.h b/include/configs/luan.h index 41999d3..805cc59 100644 --- a/include/configs/luan.h +++ b/include/configs/luan.h @@ -37,6 +37,12 @@ #define CONFIG_440 1 #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME luan +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */ #define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ @@ -44,11 +50,6 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc */ -#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) -#define CFG_SDRAM_BASE 0x00000000 /* MUST be zero */ - #define CFG_LARGE_FLASH 0xffc00000 /* 4MB flash address CS0 */ #define CFG_SMALL_FLASH 0xff900000 /* 1MB flash address CS2 */ #define CFG_SRAM_BASE 0xff800000 /* 1MB SRAM address CS2 */ @@ -87,13 +88,8 @@ * Serial Port *----------------------------------------------------------------------*/ #define CFG_EXT_SERIAL_CLOCK 11059200 /* external 11.059MHz clk */ -#define CONFIG_BAUDRATE 115200 -#undef CONFIG_SERIAL_MULTI #undef CONFIG_UART1_CONSOLE /* define if you want console on UART1 */ -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -138,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR (0xa8>>1) @@ -150,61 +143,22 @@ #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=luan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$(serverip):$(rootpath)\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs $(bootargs) " \ - "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ - ":$(hostname):$(netdev):off panic=1\0" \ - "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm $(kernel_addr)\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm $(kernel_addr) $(ramdisk_addr)\0" \ - "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/luan/uImage\0" \ +/* + * Default environment variables + */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_PPC \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc100000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/luan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_HAS_ETH0 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 1 #define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_NET_MULTI /* needed for NetConsole */ - #ifdef DEBUG #define CONFIG_PANIC_HANG #else @@ -212,60 +166,11 @@ #endif /* - * BOOTP options + * Commands additional to the ones defined in amcc-common.h */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SDRAM -/* - * Miscellaneous configurable options - */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#undef CONFIG_LYNXKDI /* support kdi files */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- @@ -286,28 +191,4 @@ #endif -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ diff --git a/include/configs/makalu.h b/include/configs/makalu.h index 566e611..65b240e 100644 --- a/include/configs/makalu.h +++ b/include/configs/makalu.h @@ -39,6 +39,13 @@ #define CONFIG_405EX 1 /* Specifc 405EX support*/ #define CONFIG_SYS_CLK_FREQ 33330000 /* ext frequency to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME makalu +#define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -46,13 +53,9 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 #define CFG_FLASH_BASE 0xFC000000 #define CFG_FPGA_BASE 0xF0000000 #define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ -#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -110,14 +113,9 @@ * Serial Port *----------------------------------------------------------------------*/ #undef CFG_EXT_SERIAL_CLOCK /* no ext. clk */ -#define CONFIG_BAUDRATE 115200 -#define CONFIG_SERIAL_MULTI 1 /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} - /*----------------------------------------------------------------------- * Environment *----------------------------------------------------------------------*/ @@ -205,9 +203,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ #define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ @@ -227,7 +223,6 @@ *----------------------------------------------------------------------*/ #define CONFIG_M88E1111_PHY 1 #define CONFIG_IBM_EMAC4_V4 1 -#define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 6 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ @@ -235,99 +230,31 @@ #define CONFIG_HAS_ETH0 1 -#define CONFIG_NET_MULTI 1 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY1_ADDR 0 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "logversion=2\0" \ - "netdev=eth0\0" \ - "hostname=makalu\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ - "addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0" \ - "flash_self_old=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "flash_self=run ramargs addip addtty addmisc;" \ - "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ - "flash_nfs_old=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr}\0" \ - "flash_nfs=run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr} - ${fdt_addr}\0" \ - "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r}\0" \ - "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ - "tftp ${fdt_addr_r} ${fdt_file}; " \ - "run nfsargs addip addtty addmisc;" \ - "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=makalu/uImage\0" \ - "fdt_file=makalu/makalu.dtb\0" \ - "kernel_addr_r=400000\0" \ - "fdt_addr_r=800000\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "fdt_addr=fc1e0000\0" \ "ramdisk_addr=fc200000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 200000 makalu/u-boot.bin\0" \ - "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \ - "cp.b ${fileaddr} fffa0000 ${filesize};" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ "pciconfighost=1\0" \ "pcie_mode=RP:RP\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ - -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */ - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_SUBNETMASK /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV #define CONFIG_CMD_DATE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ #define CONFIG_CMD_LOG -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO #define CONFIG_CMD_SNTP /* POST support */ @@ -346,37 +273,6 @@ #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/ - /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------*/ @@ -405,13 +301,6 @@ /* base address of inbound PCIe window */ #define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ @@ -470,21 +359,4 @@ #define CFG_GPIO_PCIE_CLKREQ 27 #define CFG_GPIO_PCIE_WAKE 28 -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ |