diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/MPC8544DS.h | 52 | ||||
| -rw-r--r-- | include/configs/MPC8560ADS.h | 38 | ||||
| -rw-r--r-- | include/configs/MPC8610HPCD.h | 8 | ||||
| -rw-r--r-- | include/configs/MPC8641HPCN.h | 8 | ||||
| -rw-r--r-- | include/configs/sbc8560.h | 128 |
5 files changed, 144 insertions, 90 deletions
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h index 669f4d7c..091fd2e 100644 --- a/include/configs/MPC8544DS.h +++ b/include/configs/MPC8544DS.h @@ -148,8 +148,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); */ #define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */ -#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */ - #define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */ #define CFG_BR0_PRELIM 0xff801001 @@ -158,10 +156,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_OR0_PRELIM 0xff806e65 #define CFG_OR1_PRELIM 0xff806e65 -#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE} +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} #define CFG_FLASH_QUIET_TEST -#define CFG_MAX_FLASH_BANKS 2 /* number of banks */ +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ #define CFG_MAX_FLASH_SECT 128 /* sectors per device */ #undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ @@ -203,30 +201,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); /* define to use L1 as initial stack */ -#define CONFIG_L1_INIT_RAM 1 -#define CFG_INIT_L1_LOCK 1 -#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */ -#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */ - -/* define to use L2SRAM as initial stack */ -#undef CONFIG_L2_INIT_RAM -#define CFG_INIT_L2_ADDR 0xf8fc0000 -#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */ - -#ifdef CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR -#define CFG_INIT_RAM_END CFG_INIT_L1_END -#else -#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR -#define CFG_INIT_RAM_END CFG_INIT_L2_END -#endif +#define CONFIG_L1_INIT_RAM +#define CFG_INIT_RAM_LOCK 1 +#define CFG_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */ +#define CFG_INIT_RAM_END 0x00004000 /* End of used area in RAM */ + #define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET #define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ /* Serial Port - controlled on board with jumper J8 * open - index 2 @@ -314,6 +300,26 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #if defined(CONFIG_PCI) +/*PCIE video card used*/ +#define VIDEO_IO_OFFSET CFG_PCIE2_IO_PHYS + +/*PCI video card used*/ +/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/ + +/* video */ +#define CONFIG_VIDEO + +#if defined(CONFIG_VIDEO) +#define CONFIG_BIOSEMU +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_ATI_RADEON_FB +#define CONFIG_VIDEO_LOGO +/*#define CONFIG_CONSOLE_CURSOR*/ +#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#endif + #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -382,7 +388,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #if CFG_MONITOR_BASE > 0xfff80000 #define CFG_ENV_ADDR 0xfff80000 #else -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000) #endif #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */ diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h index edf8525..27212162 100644 --- a/include/configs/MPC8560ADS.h +++ b/include/configs/MPC8560ADS.h @@ -538,29 +538,29 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "consoledev=ttyCPM\0" \ - "ramdiskaddr=1000000\0" \ - "ramdiskfile=your.ramdisk.u-boot\0" \ - "fdtaddr=400000\0" \ - "fdtfile=mpc8560ads.dtb\0" + "netdev=eth0\0" \ + "consoledev=ttyCPM\0" \ + "ramdiskaddr=1000000\0" \ + "ramdiskfile=your.ramdisk.u-boot\0" \ + "fdtaddr=400000\0" \ + "fdtfile=mpc8560ads.dtb\0" #define CONFIG_NFSBOOTCOMMAND \ - "setenv bootargs root=/dev/nfs rw " \ - "nfsroot=$serverip:$rootpath " \ - "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr - $fdtaddr" + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" #define CONFIG_RAMBOOTCOMMAND \ - "setenv bootargs root=/dev/ram rw " \ - "console=$consoledev,$baudrate $othbootargs;" \ - "tftp $ramdiskaddr $ramdiskfile;" \ - "tftp $loadaddr $bootfile;" \ - "tftp $fdtaddr $fdtfile;" \ - "bootm $loadaddr $ramdiskaddr $fdtaddr" + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h index 98ae34c..06899b1 100644 --- a/include/configs/MPC8610HPCD.h +++ b/include/configs/MPC8610HPCD.h @@ -140,11 +140,11 @@ #endif #endif -#define CFG_ID_EEPROM -#ifdef CFG_ID_EEPROM #define CONFIG_ID_EEPROM -#endif -#define ID_EEPROM_ADDR 0x57 +#define CFG_I2C_EEPROM_NXID +#define CFG_ID_EEPROM +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_EEPROM_ADDR_LEN 1 #define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */ diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h index 455e154..cd35494 100644 --- a/include/configs/MPC8641HPCN.h +++ b/include/configs/MPC8641HPCN.h @@ -152,11 +152,11 @@ extern unsigned long get_board_sys_clk(unsigned long dummy); #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */ #endif -#define CFG_ID_EEPROM 1 -#ifdef CFG_ID_EEPROM #define CONFIG_ID_EEPROM -#endif -#define ID_EEPROM_ADDR 0x57 +#define CFG_I2C_EEPROM_NXID +#define CFG_ID_EEPROM +#define CFG_I2C_EEPROM_ADDR 0x57 +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000. diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h index 146eafe..6345cce 100644 --- a/include/configs/sbc8560.h +++ b/include/configs/sbc8560.h @@ -24,8 +24,8 @@ * MA 02111-1307 USA */ -/* mpc8560ads board configuration file */ -/* please refer to doc/README.mpc85xx for more info */ +/* sbc8560 board configuration file */ +/* please refer to doc/README.sbc8560 for more info */ /* make sure you change the MAC address and other network params first, * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file */ @@ -102,11 +102,11 @@ #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */ #define SPD_EEPROM_ADDRESS 0x55 /* DDR DIMM */ -#undef CONFIG_DDR_ECC /* only for ECC DDR module */ -#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ +#undef CONFIG_DDR_ECC /* only for ECC DDR module */ +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #if defined(CONFIG_MPC85xx_REV1) - #define CONFIG_DDR_DLL /* possible DLL fix needed */ + #define CONFIG_DDR_DLL /* possible DLL fix needed */ #endif #undef CONFIG_CLOCKS_IN_MHZ @@ -177,8 +177,8 @@ #define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ -#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ -#undef CONFIG_CONS_NONE /* define if console on something else */ +#undef CONFIG_CONS_ON_SCC /* define if console on SCC */ +#undef CONFIG_CONS_NONE /* define if console on something else */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO @@ -200,6 +200,11 @@ #define CFG_PROMPT_HUSH_PS2 "> " #endif +/* pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 +#define CONFIG_OF_BOARD_SETUP 1 +#define CONFIG_OF_STDOUT_VIA_ALIAS 1 + /* * I2C */ @@ -215,16 +220,28 @@ #define CFG_PCI_MEM_PHYS 0xC0000000 #define CFG_PCI_MEM_SIZE 0x10000000 -#if defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ +#ifdef CONFIG_TSEC_ENET + +#ifndef CONFIG_NET_MULTI +#define CONFIG_NET_MULTI 1 +#endif -# define CONFIG_NET_MULTI 1 -# define CONFIG_MII 1 /* MII PHY management */ -# define CONFIG_MPC85xx_TSEC1 -# define CONFIG_MPC85xx_TSEC1_NAME "TSEC0" -# define TSEC1_PHY_ADDR 25 -# define TSEC1_PHYIDX 0 -/* Options are: TSEC0 */ -# define CONFIG_ETHPRIME "TSEC0" +#ifndef CONFIG_MII +#define CONFIG_MII 1 /* MII PHY management */ +#endif +#define CONFIG_TSEC1 1 +#define CONFIG_TSEC1_NAME "TSEC0" +#define CONFIG_TSEC2 1 +#define CONFIG_TSEC2_NAME "TSEC1" +#define TSEC1_PHY_ADDR 0x19 +#define TSEC2_PHY_ADDR 0x1a +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define TSEC1_FLAGS TSEC_GIGABIT +#define TSEC2_FLAGS TSEC_GIGABIT + +/* Options are: TSEC[0-1] */ +#define CONFIG_ETHPRIME "TSEC0" #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ @@ -272,20 +289,20 @@ * FLASH and environment organization */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ #if 0 -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION /* use hardware protection */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CFG_FLASH_PROTECTION /* use hardware protection */ #endif -#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ +#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ #if 0 /* XXX This doesn't work and I don't want to fix it */ @@ -315,9 +332,8 @@ #define CFG_ENV_SIZE 0x2000 #endif -#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=192.168.0.251:/tftpboot ip=192.168.0.105:192.168.0.251::255.255.255.0:sbc8560:eth0:off console=ttyS0,9600" +#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=dhcp console=ttyS0,9600" /*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/ -#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000" #define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ @@ -389,25 +405,57 @@ #define BOOTFLAG_WARM 0x02 /* Software reboot */ #if defined(CONFIG_CMD_KGDB) - #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ - #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif -/*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -# define CONFIG_ETHADDR 00:01:af:07:9b:8a -# define CONFIG_HAS_ETH1 -# define CONFIG_ETH1ADDR 00:01:af:07:9b:8b -# define CONFIG_HAS_ETH2 -# define CONFIG_ETH2ADDR 00:01:af:07:9b:8c +#define CONFIG_HAS_ETH0 +#define CONFIG_HAS_ETH1 #endif -#define CONFIG_SERVERIP 192.168.0.131 -#define CONFIG_IPADDR 192.168.0.105 -#define CONFIG_GATEWAYIP 0.0.0.0 -#define CONFIG_NETMASK 255.255.255.0 +/* You can compile in a MAC address and your custom net settings by using + * the following syntax. Your board should be marked with the assigned + * MAC addresses directly on it. + * + * #define CONFIG_ETHADDR de:ad:be:ef:00:00 + * #define CONFIG_ETH1ADDR fa:ke:ad:dr:es:s! + * #define CONFIG_SERVERIP <server ip> + * #define CONFIG_IPADDR <board ip> + * #define CONFIG_GATEWAYIP <gateway ip> + * #define CONFIG_NETMASK <your netmask> + */ + #define CONFIG_HOSTNAME SBC8560 #define CONFIG_ROOTPATH /home/ppc -#define CONFIG_BOOTFILE pImage +#define CONFIG_BOOTFILE uImage + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "consoledev=ttyS0\0" \ + "ramdiskaddr=2000000\0" \ + "ramdiskfile=ramdisk.uboot\0" \ + "fdtaddr=c00000\0" \ + "fdtfile=sbc8560.dtb\0" + +#define CONFIG_NFSBOOTCOMMAND \ + "setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$serverip:$rootpath " \ + "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr - $fdtaddr" + + +#define CONFIG_RAMBOOTCOMMAND \ + "setenv bootargs root=/dev/ram rw " \ + "console=$consoledev,$baudrate $othbootargs;" \ + "tftp $ramdiskaddr $ramdiskfile;" \ + "tftp $loadaddr $bootfile;" \ + "tftp $fdtaddr $fdtfile;" \ + "bootm $loadaddr $ramdiskaddr $fdtaddr" + +#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND #endif /* __CONFIG_H */ |