diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/CPCI750.h | 12 | ||||
| -rw-r--r-- | include/configs/HH405.h | 15 | ||||
| -rw-r--r-- | include/configs/delta.h | 251 | ||||
| -rw-r--r-- | include/configs/smmaco4.h | 373 | ||||
| -rw-r--r-- | include/configs/zylonite.h | 256 |
5 files changed, 902 insertions, 5 deletions
diff --git a/include/configs/CPCI750.h b/include/configs/CPCI750.h index 150e526..1632f37 100644 --- a/include/configs/CPCI750.h +++ b/include/configs/CPCI750.h @@ -285,13 +285,19 @@ * FLASH related *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI_DRIVER #define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ -#define CFG_FLASH_INCREMENT 0x01000000 /* there is only one bank */ #define CFG_FLASH_PROTECTION 1 /* use hardware protection */ #define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ #define CFG_FLASH_BASE 0xfc000000 /* start of flash banks */ +#define CFG_MAX_FLASH_BANKS 4 /* max number of memory banks */ +#define CFG_FLASH_INCREMENT 0x01000000 /* size of flash bank */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE, \ + CFG_FLASH_BASE + 1*CFG_FLASH_INCREMENT, \ + CFG_FLASH_BASE + 2*CFG_FLASH_INCREMENT, \ + CFG_FLASH_BASE + 3*CFG_FLASH_INCREMENT } +#define CFG_FLASH_EMPTY_INFO 1 /* show if bank is empty */ /* areas to map different things with the GT in physical space */ #define CFG_DRAM_BANKS 4 diff --git a/include/configs/HH405.h b/include/configs/HH405.h index 131c215..4f62b8a 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -5,6 +5,9 @@ * (C) Copyright 2005 * Stefan Roese, DENX Software Engineering, sr@denx.de. * + * (C) Copyright 2006 + * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com + * * See file CREDITS for list of people who contributed to this * project. * @@ -61,9 +64,13 @@ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_NET_MULTI 1 +#undef CONFIG_HAS_ETH1 + #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 0 /* PHY address */ +#define CONFIG_PHY_ADDR 0 /* PHY address */ #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */ +#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */ #define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/ @@ -79,6 +86,7 @@ #else #define CONFIG_VIDEO_SM501_16BPP #endif +#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000 #define CONFIG_CFB_CONSOLE #define CONFIG_VIDEO_LOGO #define CONFIG_VGA_AS_SINGLE_DEVICE @@ -434,9 +442,12 @@ #define CFG_FPGA_CTRL_VGA0_BL_MODE 0x0008 #define CFG_FPGA_CTRL_CF_RESET 0x0040 #define CFG_FPGA_CTRL_PS2_PWR 0x0080 -#define CFG_FPGA_CTRL_CF_PWR 0x0100 /* low active */ +#define CFG_FPGA_CTRL_CF_PWRN 0x0100 /* low active */ #define CFG_FPGA_CTRL_CF_BUS_EN 0x0200 #define CFG_FPGA_CTRL_LCD_CLK 0x7000 /* Mask for lcd clock */ +#define CFG_FPGA_CTRL_OW_ENABLE 0x8000 + +#define CFG_FPGA_STATUS_CF_DETECT 0x8000 #define LCD_CLK_OFF 0x0000 /* Off */ #define LCD_CLK_02083 0x1000 /* 2.083 MHz */ diff --git a/include/configs/delta.h b/include/configs/delta.h new file mode 100644 index 0000000..5b42069 --- /dev/null +++ b/include/configs/delta.h @@ -0,0 +1,251 @@ +/* + * Configuation settings for the Delta board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_CPU_MONAHANS 1 /* Intel Monahan CPU */ +#define CONFIG_DELTA 1 /* Delta board */ + +/* #define CONFIG_LCD 1 */ +#ifdef CONFIG_LCD +#define CONFIG_SHARP_LM8V31 +#endif +/* #define CONFIG_MMC 1 */ +#define BOARD_LATE_INIT 1 + +#undef CONFIG_SKIP_RELOCATE_UBOOT +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +#undef TURN_ON_ETHERNET +#ifdef TURN_ON_ETHERNET +# define CONFIG_DRIVER_SMC91111 1 +# define CONFIG_SMC91111_BASE 0x14000300 +# define CONFIG_SMC91111_EXT_PHY +# define CONFIG_SMC_USE_32_BIT +# undef CONFIG_SMC_USE_IOFUNCS /* just for use with the kernel */ +#endif + +/* + * select serial console configuration + */ +#define CONFIG_FFUART 1 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_BAUDRATE 115200 + +/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */ +#ifdef TURN_ON_ETHERNET +# define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING) +#else +# define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET) +#endif + + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_BOOTDELAY -1 +#define CONFIG_ETHADDR 08:00:3e:26:0a:5b +#define CONFIG_NETMASK 255.255.0.0 +#define CONFIG_IPADDR 192.168.0.21 +#define CONFIG_SERVERIP 192.168.0.250 +#define CONFIG_BOOTCOMMAND "bootm 80000" +#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200" +#define CONFIG_CMDLINE_TAG +#define CONFIG_TIMESTAMP + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#define CFG_LONGHELP /* undef to save memory */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_DEVICE_NULLDEV 1 + +#define CFG_MEMTEST_START 0xa0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0xa0800000 /* 4 ... 8 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* #define CFG_MMC_BASE 0xF0000000 */ + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x1000000 /* 64 MB */ +#define PHYS_SDRAM_2 0xa1000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x1000000 /* 64 MB */ +#define PHYS_SDRAM_3 0xa2000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3_SIZE 0x1000000 /* 64 MB */ +#define PHYS_SDRAM_4 0xa3000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4_SIZE 0x1000000 /* 64 MB */ + +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */ +#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */ +#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */ +#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ + +#define CFG_DRAM_BASE 0xa0000000 /* at CS0 */ +#define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */ + +#define CFG_SKIP_DRAM_SCRUB 1 + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +#define FPGA_REGS_BASE_PHYSICAL 0x08000000 + +/* + * GPIO settings + */ +#define CFG_GPSR0_VAL 0x00008000 +#define CFG_GPSR1_VAL 0x00FC0382 +#define CFG_GPSR2_VAL 0x0001FFFF +#define CFG_GPCR0_VAL 0x00000000 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPDR0_VAL 0x0060A800 +#define CFG_GPDR1_VAL 0x00FF0382 +#define CFG_GPDR2_VAL 0x0001C000 +#define CFG_GAFR0_L_VAL 0x98400000 +#define CFG_GAFR0_U_VAL 0x00002950 +#define CFG_GAFR1_L_VAL 0x000A9558 +#define CFG_GAFR1_U_VAL 0x0005AAAA +#define CFG_GAFR2_L_VAL 0xA0000000 +#define CFG_GAFR2_U_VAL 0x00000002 + +#define CFG_PSSR_VAL 0x20 + +/* + * Memory settings + */ +#define CFG_MSC0_VAL 0x23F223F2 +#define CFG_MSC1_VAL 0x3FF1A441 +#define CFG_MSC2_VAL 0x7FF97FF1 +#define CFG_MDCNFG_VAL 0x00001AC9 +#define CFG_MDREFR_VAL 0x00018018 +#define CFG_MDMRS_VAL 0x00000000 + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000000 +#define CFG_MCMEM0_VAL 0x00010504 +#define CFG_MCMEM1_VAL 0x00010504 +#define CFG_MCATT0_VAL 0x00010504 +#define CFG_MCATT1_VAL 0x00010504 +#define CFG_MCIO0_VAL 0x00004715 +#define CFG_MCIO1_VAL 0x00004715 + +#define _LED 0x08000010 +#define LED_BLANK 0x08000040 + +/* + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ + +/* NOTE: many default partitioning schemes assume the kernel starts at the + * second sector, not an environment. You have been warned! + */ +#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE) +#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE +#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16) + + +/* + * FPGA Offsets + */ +#define WHOAMI_OFFSET 0x00 +#define HEXLED_OFFSET 0x10 +#define BLANKLED_OFFSET 0x40 +#define DISCRETELED_OFFSET 0x40 +#define CNFG_SWITCHES_OFFSET 0x50 +#define USER_SWITCHES_OFFSET 0x60 +#define MISC_WR_OFFSET 0x80 +#define MISC_RD_OFFSET 0x90 +#define INT_MASK_OFFSET 0xC0 +#define INT_CLEAR_OFFSET 0xD0 +#define GP_OFFSET 0x100 + +#endif /* __CONFIG_H */ diff --git a/include/configs/smmaco4.h b/include/configs/smmaco4.h new file mode 100644 index 0000000..e106b3b --- /dev/null +++ b/include/configs/smmaco4.h @@ -0,0 +1,373 @@ +/* + * (C) Copyright 2003-2006 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * (C) Copyright 2004-2005 + * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC5xxx 1 /* This is an MPC5xxx CPU */ +#define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ +#define CONFIG_TQM5200 1 /* ... on TQM5200 module */ +#undef CONFIG_TQM5200_REV100 /* define for revision 100 modules */ + +#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ + +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Serial console configuration + */ +#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ +#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } + +/* Partitions */ +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#define CONFIG_ISO_PARTITION + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_CPU | \ + CFG_POST_I2C) + +#ifdef CONFIG_POST +#define CFG_CMD_POST_DIAG CFG_CMD_DIAG +/* preserve space for the post_word at end of on-chip SRAM */ +#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4 +#else +#define CFG_CMD_POST_DIAG 0 +#endif + +/* + * Supported commands + */ +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_ECHO | \ + CFG_CMD_EEPROM | \ + CFG_CMD_I2C | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_MII | \ + CFG_CMD_NFS | \ + CFG_CMD_PING | \ + CFG_CMD_POST_DIAG | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SNTP ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_TIMESTAMP /* display image timestamps */ + +#if (TEXT_BASE == 0xFC000000) /* Boot low */ +# define CFG_LOWBOOT 1 +#endif + +/* + * Autobooting + */ +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "rootpath=/opt/eldk/ppc_6xx\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "flash_self=run ramargs addip;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "flash_nfs=run nfsargs addip;" \ + "bootm ${kernel_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \ + "bootfile=/tftpboot/smmaco4/uImage\0" \ + "load=tftp 200000 ${u-boot}\0" \ + "u-boot=/tftpboot/smmaco4/u-boot.bin\0" \ + "update=protect off FC000000 FC05FFFF;" \ + "erase FC000000 FC05FFFF;" \ + "cp.b 200000 FC000000 ${filesize};" \ + "protect on FC000000 FC05FFFF\0" \ + "" + +#define CONFIG_BOOTCOMMAND "run net_nfs" + +/* + * IPB Bus clocking configuration. + */ +#define CFG_IPBSPEED_133 /* define for 133MHz speed */ + +#if defined(CFG_IPBSPEED_133) +/* + * PCI Bus clocking configuration + * + * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if + * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't + * been tested with a IPB Bus Clock of 66 MHz. + */ +#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#endif + +/* + * I2C configuration + */ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#ifdef CONFIG_TQM5200_REV100 +#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ +#else +#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ +#endif + +/* + * I2C clock frequency + * + * Please notice, that the resulting clock frequency could differ from the + * configured value. This is because the I2C clock is derived from system + * clock over a frequency divider with only a few divider values. U-boot + * calculates the best approximation for CFG_I2C_SPEED. However the calculated + * approximation allways lies below the configured value, never above. + */ +#define CFG_I2C_SPEED 100000 /* 100 kHz */ +#define CFG_I2C_SLAVE 0x7F + +/* + * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work + * also). For other EEPROMs configuration should be verified. On Mini-FAP the + * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the + * same configuration could be used. + */ +#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 +#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 + +/* + * Flash configuration + */ +#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ + +/* use CFI flash driver if no module variant is spezified */ +#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CFG_FLASH_CFI_DRIVER 1 /* Use the common driver */ +#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } +#define CFG_FLASH_EMPTY_INFO +#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ +#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +#if !defined(CFG_LOWBOOT) +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) +#else /* CFG_LOWBOOT */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) +#endif /* CFG_LOWBOOT */ +#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks + (= chip selects) */ +#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ + +/* Dynamic MTD partition support */ +#define CONFIG_JFFS2_CMDLINE +#define MTDIDS_DEFAULT "nor0=TQM5200-0" +#define MTDPARTS_DEFAULT "mtdparts=TQM5200-0:640k(firmware)," \ + "1408k(kernel)," \ + "2m(initrd)," \ + "4m(small-fs)," \ + "16m(big-fs)," \ + "8m(misc)" + +/* + * Environment settings + */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x10000 +#define CFG_ENV_SECT_SIZE 0x20000 +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/* + * Memory map + */ +#define CFG_MBAR 0xF0000000 +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_DEFAULT_MBAR 0x80000000 + +/* Use ON-Chip SRAM until RAM will be available */ +#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#ifdef CONFIG_POST +/* preserve space for the post_word at end of on-chip SRAM */ +#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#else +#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#endif + + +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +#define CFG_MONITOR_BASE TEXT_BASE +#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) +# define CFG_RAMBOOT 1 +#endif + +#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CFG_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/* + * Ethernet configuration + */ +#define CONFIG_MPC5xxx_FEC 1 +/* + * Define CONFIG_FEC_10MBIT to force FEC at 10Mb + */ +/* #define CONFIG_FEC_10MBIT 1 */ +#define CONFIG_PHY_ADDR 0x00 + +/* + * GPIO configuration + * + * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1): + * Bit 0 (mask: 0x80000000): 1 + * use ALT CAN position: Bits 2-3 (mask: 0x30000000): + * 00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting. + * 01 -> CAN1 on I2C1, CAN2 on Tmr0/1. + * Use for REV200 STK52XX boards. Do not use with REV100 modules + * (because, there I2C1 is used as I2C bus) + * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100 + * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030) + * 000 -> All PSC2 pins are GIOPs + * 001 -> CAN1/2 on PSC2 pins + * Use for REV100 STK52xx boards + * use PSC6: + * on STK52xx: + * use as UART. Pins PSC6_0 to PSC6_3 are used. + * Bits 9:11 (mask: 0x00700000): + * 101 -> PSC6 : Extended POST test is not available + * on MINI-FAP and TQM5200_IB: + * use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000): + * 000 -> PSC6 could not be used as UART, CODEC or IrDA + * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST + * tests. + */ +#if defined (CONFIG_MINIFAP) +# define CFG_GPS_PORT_CONFIG 0x91000004 +#elif defined (CONFIG_STK52XX) +# if defined (CONFIG_STK52XX_REV100) +# define CFG_GPS_PORT_CONFIG 0x81500014 +# else /* STK52xx REV200 and above */ +# if defined (CONFIG_TQM5200_REV100) +# error TQM5200 REV100 not supported on STK52XX REV200 or above +# else/* TQM5200 REV200 and above */ +# define CFG_GPS_PORT_CONFIG 0x91500004 +# endif +# endif +#else /* TMQ5200 Inbetriebnahme-Board */ +# define CFG_GPS_PORT_CONFIG 0x81000004 +#endif + +/* + * RTC configuration + */ +#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +/* Enable an alternate, more extensive memory test */ +#define CFG_ALT_MEMTEST + +#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ +#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +/* + * Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined, + * which is normally part of the default commands (CFV_CMD_DFL) + */ +#define CONFIG_LOOPW + +/* + * Various low-level settings + */ +#if defined(CONFIG_MPC5200) +#define CFG_HID0_INIT HID0_ICE | HID0_ICFI +#define CFG_HID0_FINAL HID0_ICE +#else +#define CFG_HID0_INIT 0 +#define CFG_HID0_FINAL 0 +#endif + +#define CFG_BOOTCS_START CFG_FLASH_BASE +#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE +#ifdef CFG_PCISPEED_66 +#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +#else +#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ +#endif +#define CFG_CS0_START CFG_FLASH_BASE +#define CFG_CS0_SIZE CFG_FLASH_SIZE + +#define CFG_CS_BURST 0x00000000 +#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ + +#define CFG_RESET_ADDRESS 0xff000000 + +#endif /* __CONFIG_H */ diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h new file mode 100644 index 0000000..4232d50 --- /dev/null +++ b/include/configs/zylonite.h @@ -0,0 +1,256 @@ +/* + * (C) Copyright 2002 + * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net + * + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * Configuation settings for the Zylonite board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_CPU_MONAHANS 1 /* Intel Monahan CPU */ +#define CONFIG_ZYLONITE 1 /* Zylonite board */ + +/* #define CONFIG_LCD 1 */ +#ifdef CONFIG_LCD +#define CONFIG_SHARP_LM8V31 +#endif +/* #define CONFIG_MMC 1 */ +#define BOARD_LATE_INIT 1 + +#undef CONFIG_SKIP_RELOCATE_UBOOT +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) +#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ + +/* + * Hardware drivers + */ + +#undef TURN_ON_ETHERNET +#ifdef TURN_ON_ETHERNET +# define CONFIG_DRIVER_SMC91111 1 +# define CONFIG_SMC91111_BASE 0x14000300 +# define CONFIG_SMC91111_EXT_PHY +# define CONFIG_SMC_USE_32_BIT +# undef CONFIG_SMC_USE_IOFUNCS /* just for use with the kernel */ +#endif + +/* + * select serial console configuration + */ +#define CONFIG_FFUART 1 + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_BAUDRATE 115200 + +/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */ +#ifdef TURN_ON_ETHERNET +# define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING) +#else +# define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET) +#endif + + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_BOOTDELAY -1 +#define CONFIG_ETHADDR 08:00:3e:26:0a:5b +#define CONFIG_NETMASK 255.255.0.0 +#define CONFIG_IPADDR 192.168.0.21 +#define CONFIG_SERVERIP 192.168.0.250 +#define CONFIG_BOOTCOMMAND "bootm 80000" +#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rootfstype=cramfs console=ttyS0,115200" +#define CONFIG_CMDLINE_TAG +#define CONFIG_TIMESTAMP + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#define CFG_LONGHELP /* undef to save memory */ +#ifdef CFG_HUSH_PARSER +#define CFG_PROMPT "$ " /* Monitor Command Prompt */ +#else +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#endif +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_DEVICE_NULLDEV 1 + +#define CFG_MEMTEST_START 0x9c000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x9c400000 /* 4 ... 8 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */ + +#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ +#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */ + + /* valid baudrates */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* #define CFG_MMC_BASE 0xF0000000 */ + +/* + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/* + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 4 /* we have 2 banks of DRAM */ +#define PHYS_SDRAM_1 0xa0000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x04000000 /* 64 MB */ +#define PHYS_SDRAM_2 0xa4000000 /* SDRAM Bank #2 */ +#define PHYS_SDRAM_2_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_3 0xa8000000 /* SDRAM Bank #3 */ +#define PHYS_SDRAM_3_SIZE 0x00000000 /* 0 MB */ +#define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ +#define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ + +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ +#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */ +#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */ +#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */ +#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ + +#define CFG_DRAM_BASE 0xa0000000 +#define CFG_DRAM_SIZE 0x04000000 + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +#define FPGA_REGS_BASE_PHYSICAL 0x08000000 + +/* + * GPIO settings + */ +#define CFG_GPSR0_VAL 0x00008000 +#define CFG_GPSR1_VAL 0x00FC0382 +#define CFG_GPSR2_VAL 0x0001FFFF +#define CFG_GPCR0_VAL 0x00000000 +#define CFG_GPCR1_VAL 0x00000000 +#define CFG_GPCR2_VAL 0x00000000 +#define CFG_GPDR0_VAL 0x0060A800 +#define CFG_GPDR1_VAL 0x00FF0382 +#define CFG_GPDR2_VAL 0x0001C000 +#define CFG_GAFR0_L_VAL 0x98400000 +#define CFG_GAFR0_U_VAL 0x00002950 +#define CFG_GAFR1_L_VAL 0x000A9558 +#define CFG_GAFR1_U_VAL 0x0005AAAA +#define CFG_GAFR2_L_VAL 0xA0000000 +#define CFG_GAFR2_U_VAL 0x00000002 + +#define CFG_PSSR_VAL 0x20 + +/* + * Memory settings + */ +#define CFG_MSC0_VAL 0x23F223F2 +#define CFG_MSC1_VAL 0x3FF1A441 +#define CFG_MSC2_VAL 0x7FF97FF1 +#define CFG_MDCNFG_VAL 0x00001AC9 +#define CFG_MDREFR_VAL 0x00018018 +#define CFG_MDMRS_VAL 0x00000000 + +/* + * PCMCIA and CF Interfaces + */ +#define CFG_MECR_VAL 0x00000000 +#define CFG_MCMEM0_VAL 0x00010504 +#define CFG_MCMEM1_VAL 0x00010504 +#define CFG_MCATT0_VAL 0x00010504 +#define CFG_MCATT1_VAL 0x00010504 +#define CFG_MCIO0_VAL 0x00004715 +#define CFG_MCIO1_VAL 0x00004715 + +#define _LED 0x08000010 +#define LED_BLANK 0x08000040 + +/* + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ + +/* NOTE: many default partitioning schemes assume the kernel starts at the + * second sector, not an environment. You have been warned! + */ +#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE) +#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE +#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16) + + +/* + * FPGA Offsets + */ +#define WHOAMI_OFFSET 0x00 +#define HEXLED_OFFSET 0x10 +#define BLANKLED_OFFSET 0x40 +#define DISCRETELED_OFFSET 0x40 +#define CNFG_SWITCHES_OFFSET 0x50 +#define USER_SWITCHES_OFFSET 0x60 +#define MISC_WR_OFFSET 0x80 +#define MISC_RD_OFFSET 0x90 +#define INT_MASK_OFFSET 0xC0 +#define INT_CLEAR_OFFSET 0xD0 +#define GP_OFFSET 0x100 + +#endif /* __CONFIG_H */ |