diff options
Diffstat (limited to 'include/configs')
44 files changed, 1194 insertions, 676 deletions
diff --git a/include/configs/afeb9260.h b/include/configs/afeb9260.h index 5e71898..14bac15 100644 --- a/include/configs/afeb9260.h +++ b/include/configs/afeb9260.h @@ -106,7 +106,7 @@ /* Ethernet */ #define CONFIG_MACB #define CONFIG_RESET_PHY_R - +#define CONFIG_AT91_WANTS_COMMON_PHY #define CONFIG_NET_RETRY_COUNT 20 /* USB */ diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index d75df92..8af4d6a 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -42,12 +42,11 @@ "dfu_alt_info_nand=" DFU_ALT_INFO_NAND "\0" \ "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \ "nandrootfstype=ubifs rootwait=1\0" \ - "nandsrcaddr=0x280000\0" \ - "nandboot=echo Booting from nand ...; " \ + "nandboot=echo Booting from nand ...; " \ "run nandargs; " \ - "nand read ${loadaddr} ${nandsrcaddr} ${nandimgsize}; " \ - "bootz ${loadaddr}\0" \ - "nandimgsize=0x500000\0" + "nand read ${fdtaddr} u-boot-spl-os; " \ + "nand read ${loadaddr} kernel; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" #else #define NANDARGS "" #endif @@ -198,6 +197,10 @@ #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_YMODEM_SUPPORT +/* Bootcount using the RTC block */ +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_BOOTCOUNT_AM33XX + /* CPSW support */ #define CONFIG_SPL_ETH_SUPPORT diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h index a3473b5..1fa477a 100644 --- a/include/configs/am3517_evm.h +++ b/include/configs/am3517_evm.h @@ -141,8 +141,18 @@ #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 #define CONFIG_SYS_I2C_OMAP34XX -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS +/* + * Ethernet + */ +#define CONFIG_DRIVER_TI_EMAC +#define CONFIG_DRIVER_TI_EMAC_USE_RMII +#define CONFIG_MII +#define CONFIG_BOOTP_DEFAULT +#define CONFIG_BOOTP_DNS +#define CONFIG_BOOTP_DNS2 +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_NET_RETRY_COUNT 10 + /* * Board NAND Info. */ diff --git a/include/configs/arndale.h b/include/configs/arndale.h index ea8753b..a3cb56b 100644 --- a/include/configs/arndale.h +++ b/include/configs/arndale.h @@ -198,10 +198,6 @@ #define BL2_START_OFFSET (CONFIG_BL2_OFFSET/512) #define BL2_SIZE_BLOC_COUNT (CONFIG_BL2_SIZE/512) -#define CONFIG_SPI_BOOTING -#define EXYNOS_COPY_SPI_FNPTR_ADDR 0x02020058 -#define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) - #define CONFIG_DOS_PARTITION #define CONFIG_EFI_PARTITION #define CONFIG_CMD_PART diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h index 1c4bb81..73917b0 100644 --- a/include/configs/at91sam9260ek.h +++ b/include/configs/at91sam9260ek.h @@ -181,6 +181,7 @@ #define CONFIG_RMII 1 #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_RESET_PHY_R 1 +#define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ #define CONFIG_USB_ATMEL diff --git a/include/configs/at91sam9263ek.h b/include/configs/at91sam9263ek.h index 0a1969d..b9aa036 100644 --- a/include/configs/at91sam9263ek.h +++ b/include/configs/at91sam9263ek.h @@ -275,6 +275,7 @@ #define CONFIG_RMII 1 #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_RESET_PHY_R 1 +#define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ #define CONFIG_USB_ATMEL diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h index 2095fe6..ccfda71 100644 --- a/include/configs/at91sam9m10g45ek.h +++ b/include/configs/at91sam9m10g45ek.h @@ -15,7 +15,6 @@ #define CONFIG_SYS_TEXT_BASE 0x73f00000 -#define CONFIG_AT91_LEGACY #define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ /* ARM asynchronous clock */ @@ -77,6 +76,10 @@ /* * Command line configuration. */ + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + #include <config_cmd_default.h> #undef CONFIG_CMD_BDI #undef CONFIG_CMD_FPGA @@ -97,9 +100,6 @@ #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) -/* No NOR flash */ -#define CONFIG_SYS_NO_FLASH - /* NAND flash */ #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_ATMEL @@ -120,6 +120,7 @@ #define CONFIG_RMII #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_RESET_PHY_R +#define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ #define CONFIG_USB_EHCI diff --git a/include/configs/at91sam9n12ek.h b/include/configs/at91sam9n12ek.h index 4ec1799..e23549d 100644 --- a/include/configs/at91sam9n12ek.h +++ b/include/configs/at91sam9n12ek.h @@ -113,8 +113,8 @@ #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 4 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTD, 5 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(4) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(5) /* PMECC & PMERRLOC */ #define CONFIG_ATMEL_NAND_HWECC diff --git a/include/configs/cm_t335.h b/include/configs/cm_t335.h new file mode 100644 index 0000000..56e9a8e --- /dev/null +++ b/include/configs/cm_t335.h @@ -0,0 +1,182 @@ +/* + * Config file for Compulab CM-T335 board + * + * Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/ + * + * Author: Ilya Ledvich <ilya@compulab.co.il> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_CM_T335_H +#define __CONFIG_CM_T335_H + +#define CONFIG_CM_T335 +#define CONFIG_NAND + +#include <configs/ti_am335x_common.h> + +#undef CONFIG_BOARD_LATE_INIT +#undef CONFIG_SPI +#undef CONFIG_OMAP3_SPI +#undef CONFIG_CMD_SPI +#undef CONFIG_SPL_OS_BOOT +#undef CONFIG_BOOTCOUNT_LIMIT +#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC + +#undef CONFIG_MAX_RAM_BANK_SIZE +#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */ + +#undef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "CM-T335 # " + +#define CONFIG_OMAP_COMMON + +#define MACH_TYPE_CM_T335 4586 /* Until the next sync */ +#define CONFIG_MACH_TYPE MACH_TYPE_CM_T335 + +/* Clock Defines */ +#define V_OSCK 25000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */ + +#ifndef CONFIG_SPL_BUILD +#define MMCARGS \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 rw rootwait\0" \ + "mmcrootfstype=ext4\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "bootm ${loadaddr}\0" + +#define NANDARGS \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandroot=ubi0:rootfs rw\0" \ + "nandrootfstype=ubifs\0" \ + "nandargs=setenv bootargs console=${console} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype} " \ + "ubi.mtd=${rootfs_name}\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nboot ${loadaddr} nand0 900000; " \ + "bootm ${loadaddr}\0" + + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=82000000\0" \ + "console=ttyO0,115200n8\0" \ + "rootfs_name=rootfs\0" \ + "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source ${loadaddr}\0" \ + "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ + MMCARGS \ + NANDARGS + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run nandboot; " \ + "fi; " \ + "fi; " \ + "else run nandboot; fi" +#endif /* CONFIG_SPL_BUILD */ + +#define CONFIG_TIMESTAMP +#define CONFIG_SYS_AUTOLOAD "no" + +/* Serial console configuration */ +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SERIAL1 1 /* UART0 */ + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ +#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */ +#define CONFIG_BAUDRATE 115200 + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 + +/* SPL */ +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +/* Network. */ +#define CONFIG_PHY_GIGE +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 0 +#define CONFIG_PHY_ATHEROS + +/* NAND support */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE + +#undef CONFIG_SYS_NAND_U_BOOT_OFFS +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000 + +#define CONFIG_CMD_NAND +#define GPMC_NAND_ECC_LP_x8_LAYOUT +#define MTDIDS_DEFAULT "nand0=nand" +#define MTDPARTS_DEFAULT "mtdparts=nand:2m(spl)," \ + "1m(u-boot),1m(u-boot-env)," \ + "1m(dtb),4m(splash)," \ + "6m(kernel),-(rootfs)" +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x300000 /* environment starts here */ +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ +#define CONFIG_SYS_NAND_ONFI_DETECTION + +/* GPIO pin + bank to pin ID mapping */ +#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin) + +/* Status LED */ +#define CONFIG_STATUS_LED +#define CONFIG_GPIO_LED +#define CONFIG_BOARD_SPECIFIC_LED +#define STATUS_LED_BIT GPIO_PIN(2, 0) +/* Status LED polarity is inversed, so init it in the "off" state */ +#define STATUS_LED_STATE STATUS_LED_OFF +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +#define STATUS_LED_BOOT 0 + +#ifndef CONFIG_SPL_BUILD +/* + * Enable PCA9555 at I2C0-0x26. + * First select the I2C0 bus with "i2c dev 0", then use "pca953x" command. + */ +#define CONFIG_PCA953X +#define CONFIG_CMD_PCA953X +#define CONFIG_CMD_PCA953X_INFO +#define CONFIG_SYS_I2C_PCA953X_ADDR 0x26 +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x26, 16} } +#endif /* CONFIG_SPL_BUILD */ + +#endif /* __CONFIG_CM_T335_H */ + diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index f4ecd0d..e72187e 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -302,12 +302,13 @@ /* Status LED */ #define CONFIG_STATUS_LED /* Status LED enabled */ #define CONFIG_BOARD_SPECIFIC_LED -#define STATUS_LED_GREEN 0 -#define STATUS_LED_BIT STATUS_LED_GREEN +#define CONFIG_GPIO_LED +#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */ +#define GREEN_LED_DEV 0 +#define STATUS_LED_BIT GREEN_LED_GPIO #define STATUS_LED_STATE STATUS_LED_ON #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -#define STATUS_LED_BOOT STATUS_LED_BIT -#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */ +#define STATUS_LED_BOOT GREEN_LED_DEV #define CONFIG_SPLASHIMAGE_GUARD diff --git a/include/configs/corvus.h b/include/configs/corvus.h new file mode 100644 index 0000000..11ba4cf --- /dev/null +++ b/include/configs/corvus.h @@ -0,0 +1,165 @@ +/* + * Common board functions for siemens AT91SAM9G45 based boards + * (C) Copyright 2013 Siemens AG + * + * Based on: + * U-Boot file: include/configs/at91sam9m10g45ek.h + * (C) Copyright 2007-2008 + * Stelian Pop <stelian@popies.net> + * Lead Tech Design <www.leadtechdesign.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/hardware.h> + +#define MACH_TYPE_CORVUS 2066 + +/* + * Warning: changing CONFIG_SYS_TEXT_BASE requires + * adapting the initial boot program. + * Since the linker has to swallow that define, we must use a pure + * hex number here! + */ + +#define CONFIG_SYS_TEXT_BASE 0x73f00000 + +#define CONFIG_AT91_LEGACY +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */ +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_AT91FAMILY + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT + +/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS + +/* LED */ +#define CONFIG_AT91_LED +#define CONFIG_RED_LED AT91_PIN_PD31 /* this is the user1 led */ +#define CONFIG_GREEN_LED AT91_PIN_PD0 /* this is the user2 led */ + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NAND +#define CONFIG_CMD_USB + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6 +#define CONFIG_SYS_SDRAM_SIZE 0x08000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) + +/* No NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* NAND flash */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8 + +#endif + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_AT91_WANTS_COMMON_PHY + +/* USB */ +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_ATMEL +#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2 +#define CONFIG_DOS_PARTITION +#define CONFIG_USB_STORAGE + +#define CONFIG_SYS_LOAD_ADDR 0x72000000 /* load address */ + +/* bootstrap + u-boot + env in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x100000 +#define CONFIG_ENV_OFFSET_REDUND 0x180000 +#define CONFIG_ENV_SIZE 0x20000 + +#define CONFIG_BOOTCOMMAND \ + "nand read 0x70000000 0x200000 0x300000;" \ + "bootm 0x70000000" +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256k(env),256k(env_redundant),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "root=/dev/mtdblock7 rw rootfstype=jffs2" + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + \ + 128*1024, 0x1000) + +#endif diff --git a/include/configs/cpu9260.h b/include/configs/cpu9260.h index ccf36a5..39f7062 100644 --- a/include/configs/cpu9260.h +++ b/include/configs/cpu9260.h @@ -280,8 +280,8 @@ #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_NAND_DBW_8 1 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTC, 13 -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PC(13) +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) @@ -310,6 +310,7 @@ #define CONFIG_RMII #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_MACB_SEARCH_PHY +#define CONFIG_AT91_WANTS_COMMON_PHY /* LEDS */ /* Status LED */ diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 8a69c7d..48b47cb 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -83,4 +83,15 @@ #define CONFIG_OMAP_USB_PHY #define CONFIG_OMAP_USB2PHY2_HOST +/* SATA */ +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_CMD_SCSI +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + #endif /* __CONFIG_DRA7XX_EVM_H */ diff --git a/include/configs/dxr2.h b/include/configs/dxr2.h index cd553ec..1e42f5c 100644 --- a/include/configs/dxr2.h +++ b/include/configs/dxr2.h @@ -21,8 +21,8 @@ #define CONFIG_SYS_MPUCLK 275 #define DXR2_IOCTRL_VAL 0x18b -#define DDR_PLL_FREQ 266 -#define CONFIG_SPL_AM33XX_DO_NOT_ENABLE_RTC32K +#define DDR_PLL_FREQ 303 +#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC #define BOARD_DFU_BUTTON_GPIO 27 #define BOARD_DFU_BUTTON_LED 64 @@ -62,7 +62,7 @@ /* Default env settings */ #define CONFIG_EXTRA_ENV_SETTINGS \ "hostname=dxr2\0" \ - "nand_img_size=0x300000\0" \ + "nand_img_size=0x400000\0" \ "optargs=\0" \ CONFIG_COMMON_ENV_SETTINGS @@ -75,10 +75,9 @@ "run dfu_start; " \ "reset; " \ "fi;" \ -"if ping ${serverip}; then " \ - "run net_nfs; " \ -"fi;" \ -"run nand_boot;" +"run nand_boot;" \ +"reset;" + #else #define CONFIG_BOOTDELAY 0 diff --git a/include/configs/eb_cpux9k2.h b/include/configs/eb_cpux9k2.h index 2d8c42c..f7e70aa 100644 --- a/include/configs/eb_cpux9k2.h +++ b/include/configs/eb_cpux9k2.h @@ -41,10 +41,6 @@ #define CONFIG_SYS_LOAD_ADDR 0x21000000 /* default load address */ #define CONFIG_STANDALONE_LOAD_ADDR 0x21000000 -#define CONFIG_SYS_BOOT_SIZE 0x00 /* 0 KBytes */ -#define CONFIG_SYS_U_BOOT_BASE PHYS_FLASH_1 -#define CONFIG_SYS_U_BOOT_SIZE 0x60000 /* 384 KBytes */ - #define CONFIG_BOOT_RETRY_TIME 30 #define CONFIG_CMDLINE_EDITING diff --git a/include/configs/ethernut5.h b/include/configs/ethernut5.h index 252df54..480d867 100644 --- a/include/configs/ethernut5.h +++ b/include/configs/ethernut5.h @@ -149,7 +149,7 @@ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) #endif /* JFFS2 */ diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h index 1e9c1e3..8fb904c 100644 --- a/include/configs/exynos5250-dt.h +++ b/include/configs/exynos5250-dt.h @@ -157,6 +157,7 @@ #define COPY_BL2_FNPTR_ADDR 0x02020030 #define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT /* specific .lds file */ #define CONFIG_SPL_LDSCRIPT "board/samsung/common/exynos-uboot-spl.lds" @@ -266,6 +267,7 @@ /* SPI */ #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_SPI_FLASH +#define CONFIG_ENV_SPI_BASE 0x12D30000 #ifdef CONFIG_SPI_FLASH #define CONFIG_EXYNOS_SPI @@ -291,27 +293,6 @@ #define CONFIG_POWER_I2C #define CONFIG_POWER_MAX77686 -/* SPI */ -#define CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_SPI_FLASH - -#ifdef CONFIG_SPI_FLASH -#define CONFIG_EXYNOS_SPI -#define CONFIG_CMD_SF -#define CONFIG_CMD_SPI -#define CONFIG_SPI_FLASH_WINBOND -#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 -#define CONFIG_SF_DEFAULT_SPEED 50000000 -#define EXYNOS5_SPI_NUM_CONTROLLERS 5 -#endif - -#ifdef CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 -#define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE -#define CONFIG_ENV_SPI_BUS 1 -#define CONFIG_ENV_SPI_MAX_HZ 50000000 -#endif - /* Ethernet Controllor Driver */ #ifdef CONFIG_CMD_NET #define CONFIG_SMC911X diff --git a/include/configs/h2_p2_dbg_board.h b/include/configs/h2_p2_dbg_board.h deleted file mode 100644 index 4ba2c55..0000000 --- a/include/configs/h2_p2_dbg_board.h +++ /dev/null @@ -1,120 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * TI H2 and P2 Debug Board hardware map - * - * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) - * Author: MPC-Data Limited - * Dave Peverley - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __INCLUDED_H2_P2_DBH_BOARD_H -#define __INCLUDED_H2_P2_DBH_BOARD_H - -#include <asm/sizes.h> - -/* - * The Debug board is designed to function with the P2 Sample, H2 - * Sample and 1610 Innovator boards. The main difference AFAICT is - * the chip selects used with each system ; - * - * P2 Sample : CS1 of OMAP730 is used to select the CPLD & LAN regs - * H2 Sample : CS1a is used to select the CPLD registers. - * - */ - -/*************************************************************************** - * CPLD Registers - **************************************************************************/ - -#define H2DBG_CPLD_REVISION 0x04000010 -#define H2DBG_BOARD_REVISION 0x04000012 -#define H2DBG_GPIO_REGISTER 0x04000014 -#define H2DBG_LED_CONTROL 0x04000016 -#define H2DBG_MISC_INPUT 0x04000018 -#define H2DBG_LAN_STATUS 0x0400001A -#define H2DBG_LAN_RESET 0x0400001C -#define H2DBG_ETH_REG_BASE 0x04000300 - -/*************************************************************************** - * Ethernet Control Registers - * These are for the LAN91C96 on the debug board - **************************************************************************/ - -/* Bank 0 in IO space */ - -#define ETH_TCR (H2DBG_ETH_REG_BASE + 0x00) /* Transmit Control Register */ -#define ETH_EPH_STATUS (H2DBG_ETH_REG_BASE + 0x02) /* EPH Status Register */ -#define ETH_RCR (H2DBG_ETH_REG_BASE + 0x04) /* Receive Control Register */ -#define ETH_COUNTER (H2DBG_ETH_REG_BASE + 0x06) /* Counter Register */ -#define ETH_MIR (H2DBG_ETH_REG_BASE + 0x08) /* Memory Information Register */ -#define ETH_MCR (H2DBG_ETH_REG_BASE + 0x0A) /* Memory Configuration Register */ - -/* Bank 1 in IO space */ - -#define ETH_CONFIG (H2DBG_ETH_REG_BASE + 0x00) /* Configuration Register */ -#define ETH_BASE (H2DBG_ETH_REG_BASE + 0x02) /* Base Address Register */ -#define ETH_IA0 (H2DBG_ETH_REG_BASE + 0x04) /* Individual Address Register - 0 */ -#define ETH_IA1 (H2DBG_ETH_REG_BASE + 0x05) /* Individual Address Register - 1 */ -#define ETH_IA2 (H2DBG_ETH_REG_BASE + 0x06) /* Individual Address Register - 2 */ -#define ETH_IA3 (H2DBG_ETH_REG_BASE + 0x07) /* Individual Address Register - 3 */ -#define ETH_IA4 (H2DBG_ETH_REG_BASE + 0x08) /* Individual Address Register - 4 */ -#define ETH_IA5 (H2DBG_ETH_REG_BASE + 0x09) /* Individual Address Register - 5 */ -#define ETH_GEN_PURPOSE (H2DBG_ETH_REG_BASE + 0x0A) /* General Address Registers */ -#define ETH_CONTROL (H2DBG_ETH_REG_BASE + 0x0B) /* Control Register */ - -/* Bank 2 in IO space */ - -#define ETH_MMU (H2DBG_ETH_REG_BASE + 0x00) /* MMU Command Register */ -#define ETH_AUTO_TX_START (H2DBG_ETH_REG_BASE + 0x01) /* Auto Tx Start Register */ -#define ETH_PNR (H2DBG_ETH_REG_BASE + 0x02) /* Packet Number Register */ -#define ETH_ARR (H2DBG_ETH_REG_BASE + 0x03) /* Allocation Result Register */ -#define ETH_FIFO (H2DBG_ETH_REG_BASE + 0x04) /* FIFO Ports Register */ -#define ETH_POINTER (H2DBG_ETH_REG_BASE + 0x06) /* Pointer Register */ -#define ETH_DATA_HIGH (H2DBG_ETH_REG_BASE + 0x08) /* Data High Register */ -#define ETH_DATA_LOW (H2DBG_ETH_REG_BASE + 0x0A) /* Data Low Register */ -#define ETH_INT_STATS (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Status Register - RO */ -#define ETH_INT_ACK (H2DBG_ETH_REG_BASE + 0x0C) /* Interrupt Acknowledge Register -WO */ -#define ETH_INT_MASK (H2DBG_ETH_REG_BASE + 0x0D) /* Interrupt Mask Register */ - - -#ifndef __ASSEMBLY__ - -/* - * A couple of utility inlines to aid debugging using the LED's on the - * debug board. - */ - -static inline void set_led_state(int state) -{ - static unsigned long hw_led_state = 0; - volatile unsigned short *led_address = (volatile unsigned short *)0x04000016; - - hw_led_state = ((unsigned long)state); - *((unsigned short *) (led_address)) = (unsigned short) (~hw_led_state & 0xFFFF); -} - - -static inline void spin_up_leds(void) -{ - volatile int i, j, k; - - for (k = 0; k < 2; k++) { - for (i = 0; i < 16; i++) { - for (j = 0; j < 5000; j++) { - set_led_state(1 << i); - } - } - for (i = 15; i >= 0; i--) { - for (j = 0; j < 5000; j++) { - set_led_state(1 << i); - } - } - } -} - -#endif /* ! __ASSEMBLY__ */ - -#endif /* ! __INCLUDED_H2_P2_DBH_BOARD_H */ diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h new file mode 100644 index 0000000..59c4948 --- /dev/null +++ b/include/configs/koelsch.h @@ -0,0 +1,133 @@ +/* + * include/configs/koelsch.h + * + * Copyright (C) 2013 Renesas Electronics Corporation + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#ifndef __KOELSCH_H +#define __KOELSCH_H + +#undef DEBUG +#define CONFIG_ARMV7 +#define CONFIG_R8A7791 +#define CONFIG_RMOBILE +#define CONFIG_RMOBILE_BOARD_STRING "Koelsch" +#define CONFIG_SH_GPIO_PFC + +#include <asm/arch/rmobile.h> + +#define CONFIG_CMD_EDITENV +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_DFL +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_RUN +#define CONFIG_CMD_LOADS +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_FLASH + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_OF_LIBFDT +#define BOARD_LATE_INIT + +#define CONFIG_BAUDRATE 38400 +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTARGS "" + +#define CONFIG_VERSION_VARIABLE +#undef CONFIG_SHOW_BOOT_PROGRESS + +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_USE_ARCH_MEMSET +#define CONFIG_USE_ARCH_MEMCPY +#define CONFIG_TMU_TIMER + +/* STACK */ +#define CONFIG_SYS_INIT_SP_ADDR 0xE633fffc +#define STACK_AREA_SIZE 0xC000 +#define LOW_LEVEL_MERAM_STACK \ + (CONFIG_SYS_INIT_SP_ADDR + STACK_AREA_SIZE - 4) + +/* MEMORY */ +#define KOELSCH_SDRAM_BASE 0x40000000 +#define KOELSCH_SDRAM_SIZE (2048u * 1024 * 1024) +#define KOELSCH_UBOOT_SDRAM_SIZE (512 * 1024 * 1024) + +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_PBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE 512 +#define CONFIG_SYS_BAUDRATE_TABLE { 38400, 115200 } + +/* SCIF */ +#define CONFIG_SCIF_CONSOLE +#define CONFIG_CONS_SCIF0 +#define SCIF0_BASE 0xe6e60000 +#undef CONFIG_SYS_CONSOLE_INFO_QUIET +#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE + +#define CONFIG_SYS_MEMTEST_START (KOELSCH_SDRAM_BASE) +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ + 504 * 1024 * 1024) +#undef CONFIG_SYS_ALT_MEMTEST +#undef CONFIG_SYS_MEMTEST_SCRATCH +#undef CONFIG_SYS_LOADS_BAUD_CHANGE + +#define CONFIG_SYS_SDRAM_BASE (KOELSCH_SDRAM_BASE) +#define CONFIG_SYS_SDRAM_SIZE (KOELSCH_UBOOT_SDRAM_SIZE) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fc0) +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) +#define CONFIG_SYS_GBL_DATA_SIZE (256) +#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) + +/* FLASH */ +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_FLASH_SHOW_PROGRESS 45 +#define CONFIG_SYS_FLASH_BASE 0x00000000 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MB */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) } +#define CONFIG_SYS_FLASH_BANKS_SIZES { (CONFIG_SYS_FLASH_SIZE) } +#define CONFIG_SYS_FLASH_ERASE_TOUT 3000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 +#define CONFIG_SYS_FLASH_LOCK_TOUT 3000 +#define CONFIG_SYS_FLASH_UNLOCK_TOUT 3000 + +/* ENV setting */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ENV_SECT_SIZE (256 * 1024) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR) +#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN) + +/* Board Clock */ +#define CONFIG_SYS_CLK_FREQ 10000000 +#define CONFIG_SH_TMU_CLK_FREQ CONFIG_SYS_CLK_FREQ +#define CONFIG_SH_SCIF_CLK_FREQ 14745600 +#define CONFIG_SYS_TMU_CLK_DIV 4 +#define CONFIG_SYS_HZ 1000 + +#endif /* __KOELSCH_H */ diff --git a/include/configs/lager.h b/include/configs/lager.h new file mode 100644 index 0000000..7819edd --- /dev/null +++ b/include/configs/lager.h @@ -0,0 +1,141 @@ +/* + * include/configs/lager.h + * This file is lager board configuration. + * + * Copyright (C) 2013 Renesas Electronics Corporation + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#ifndef __LAGER_H +#define __LAGER_H + +#undef DEBUG +#define CONFIG_ARMV7 +#define CONFIG_R8A7790 +#define CONFIG_RMOBILE +#define CONFIG_RMOBILE_BOARD_STRING "Lager" +#define CONFIG_SH_GPIO_PFC +#define MACH_TYPE_LAGER 4538 +#define CONFIG_MACH_TYPE MACH_TYPE_LAGER + +#include <asm/arch/rmobile.h> + +#define CONFIG_CMD_EDITENV +#define CONFIG_CMD_SAVEENV +#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_DFL +#define CONFIG_CMD_SDRAM +#define CONFIG_CMD_RUN +#define CONFIG_CMD_LOADS +#define CONFIG_CMD_BOOTZ +#define CONFIG_CMD_FLASH + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMDLINE_EDITING +#define CONFIG_OF_LIBFDT + +/* #define CONFIG_OF_LIBFDT */ +#define BOARD_LATE_INIT + +#define CONFIG_BAUDRATE 38400 +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTARGS "" + +#define CONFIG_VERSION_VARIABLE +#undef CONFIG_SHOW_BOOT_PROGRESS + +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_USE_ARCH_MEMSET +#define CONFIG_USE_ARCH_MEMCPY +#define CONFIG_TMU_TIMER + +/* STACK */ +#define CONFIG_SYS_INIT_SP_ADDR 0xE827fffc +#define STACK_AREA_SIZE 0xC000 +#define LOW_LEVEL_MERAM_STACK \ + (CONFIG_SYS_INIT_SP_ADDR + STACK_AREA_SIZE - 4) + +/* MEMORY */ +#define LAGER_SDRAM_BASE 0x40000000 +#define LAGER_SDRAM_SIZE (2048u * 1024 * 1024) +#define LAGER_UBOOT_SDRAM_SIZE (512 * 1024 * 1024) + +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_PBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE 512 +#define CONFIG_SYS_BAUDRATE_TABLE { 38400, 115200 } + +/* SCIF */ +#define CONFIG_SCIF_CONSOLE +#define CONFIG_CONS_SCIF0 +#define SCIF0_BASE 0xe6e60000 +#undef CONFIG_SYS_CONSOLE_INFO_QUIET +#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE + +#define CONFIG_SYS_MEMTEST_START (LAGER_SDRAM_BASE) +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \ + 504 * 1024 * 1024) +#undef CONFIG_SYS_ALT_MEMTEST +#undef CONFIG_SYS_MEMTEST_SCRATCH +#undef CONFIG_SYS_LOADS_BAUD_CHANGE + +#define CONFIG_SYS_SDRAM_BASE (LAGER_SDRAM_BASE) +#define CONFIG_SYS_SDRAM_SIZE (LAGER_UBOOT_SDRAM_SIZE) +#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fc0) +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_MONITOR_BASE 0x00000000 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) +#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024) +#define CONFIG_SYS_GBL_DATA_SIZE (256) +#define CONFIG_SYS_BOOTMAPSZ (8 * 1024 * 1024) + +/* USE NOR FLASH */ +#define CONFIG_SYS_TEXT_BASE 0x00000000 +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS +#define CONFIG_FLASH_SHOW_PROGRESS 45 +#define CONFIG_SYS_FLASH_BASE 0x00000000 +#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MB */ +#define CONFIG_SYS_MAX_FLASH_SECT 1024 +#define CONFIG_SYS_MAX_FLASH_BANKS 1 +#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) } +#define CONFIG_SYS_FLASH_BANKS_SIZES { (CONFIG_SYS_FLASH_SIZE) } +#define CONFIG_SYS_FLASH_ERASE_TOUT 3000 +#define CONFIG_SYS_FLASH_WRITE_TOUT 3000 +#define CONFIG_SYS_FLASH_LOCK_TOUT 3000 +#define CONFIG_SYS_FLASH_UNLOCK_TOUT 3000 + +/* ENV setting */ +#define CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_OVERWRITE 1 +#define CONFIG_ENV_SECT_SIZE (256 * 1024) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \ + CONFIG_SYS_MONITOR_LEN) +#define CONFIG_ENV_OFFSET (CONFIG_ENV_ADDR) +#define CONFIG_ENV_SIZE (CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_SYS_MONITOR_LEN) + +/* Board Clock */ +#define CONFIG_BASE_CLK_FREQ 20000000u +#define CONFIG_SH_TMU_CLK_FREQ (CONFIG_BASE_CLK_FREQ / 2) /* EXT / 2 */ +#define CONFIG_PLL1_CLK_FREQ (CONFIG_BASE_CLK_FREQ * 156 / 2) +#define CONFIG_PLL1_DIV2_CLK_FREQ (CONFIG_PLL1_CLK_FREQ / 2) +#define CONFIG_MP_CLK_FREQ (CONFIG_PLL1_DIV2_CLK_FREQ / 15) +#define CONFIG_SH_SCIF_CLK_FREQ CONFIG_MP_CLK_FREQ + +#define CONFIG_SYS_TMU_CLK_DIV 4 +#define CONFIG_SYS_HZ 1000 + +#endif /* __LAGER_H */ diff --git a/include/configs/meesc.h b/include/configs/meesc.h index 91f6e2f..86ce5f2 100644 --- a/include/configs/meesc.h +++ b/include/configs/meesc.h @@ -143,8 +143,8 @@ # define CONFIG_SYS_NAND_DBW_8 # define CONFIG_SYS_NAND_MASK_ALE (1 << 21) # define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -# define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 -# define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22 +# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) +# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22) #endif /* Ethernet */ diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h index 9eab190..3acb854 100644 --- a/include/configs/omap3_beagle.h +++ b/include/configs/omap3_beagle.h @@ -118,9 +118,6 @@ #define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147 -#define CONFIG_USB_ULPI -#define CONFIG_USB_ULPI_VIEWPORT_OMAP - #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h index 6820e42..73dc088 100644 --- a/include/configs/omap4_panda.h +++ b/include/configs/omap4_panda.h @@ -36,9 +36,6 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_DHCP -#define CONFIG_USB_ULPI -#define CONFIG_USB_ULPI_VIEWPORT_OMAP - #include <configs/omap4_common.h> #define CONFIG_CMD_NET diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index 4d3a800..2f128b8 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -69,4 +69,14 @@ /* Max time to hold reset on this board, see doc/README.omap-reset-time */ #define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_CMD_SCSI +#define CONFIG_LIBATA +#define CONFIG_SCSI_AHCI +#define CONFIG_SCSI_AHCI_PLAT +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \ + CONFIG_SYS_SCSI_MAX_LUN) + #endif /* __CONFIG_OMAP5_EVM_H */ diff --git a/include/configs/omap730.h b/include/configs/omap730.h deleted file mode 100644 index b54e0fb..0000000 --- a/include/configs/omap730.h +++ /dev/null @@ -1,246 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * OMAP730 hardware map - * - * Copyright (C) 2004 MPC-Data Limited. (http://www.mpc-data.co.uk) - * Author: MPC-Data Limited - * Dave Peverley - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __INCLUDED_OMAP730_H -#define __INCLUDED_OMAP730_H - -#include <asm/sizes.h> - -/*************************************************************************** - * OMAP730 Configuration Registers - **************************************************************************/ - -#define PERSEUS2_MPU_DEV_ID ((unsigned int)(0xFFFE1000)) -#define PERSEUS2_GSM_DEV_ID0 ((unsigned int)(0xFFFE1000)) -#define PERSEUS2_GDM_DEV_ID1 ((unsigned int)(0xFFFE1002)) -#define DSP_CONF ((unsigned int)(0xFFFE1004)) -#define PERSEUS2_MPU_DIE_ID0 ((unsigned int)(0xFFFE1008)) -#define GSM_ASIC_CONF ((unsigned int)(0xFFFE1008)) -#define PERSEUS2_MPU_DIE_ID1 ((unsigned int)(0xFFFE100C)) -#define PERSEUS2_MODE1 ((unsigned int)(0xFFFE1010)) -#define PERSEUS2_GSM_DIE_ID0 ((unsigned int)(0xFFFE1010)) -#define PERSEUS2_GSM_DIE_ID1 ((unsigned int)(0xFFFE1012)) -#define PERSEUS2_MODE2 ((unsigned int)(0xFFFE1014)) -#define PERSEUS2_GSM_DIE_ID2 ((unsigned int)(0xFFFE1014)) -#define PERSEUS2_GSM_DIE_ID3 ((unsigned int)(0xFFFE1016)) -#define PERSEUS2_ANALOG_CELLS_CONF ((unsigned int)(0xFFFE1018)) -#define SPECCTL ((unsigned int)(0xFFFE101C)) -#define SPARE1 ((unsigned int)(0xFFFE1020)) -#define SPARE2 ((unsigned int)(0xFFFE1024)) -#define GSM_PBG_IRQ ((unsigned int)(0xFFFE1028)) -#define DMA_REQ_CONF ((unsigned int)(0xFFFE1030)) -#define PE_CONF_NO_DUAL ((unsigned int)(0xFFFE1060)) -#define PERSEUS2_IO_CONF0 ((unsigned int)(0xFFFE1070)) -#define PERSEUS2_IO_CONF1 ((unsigned int)(0xFFFE1074)) -#define PERSEUS2_IO_CONF2 ((unsigned int)(0xFFFE1078)) -#define PERSEUS2_IO_CONF3 ((unsigned int)(0xFFFE107C)) -#define PERSEUS2_IO_CONF4 ((unsigned int)(0xFFFE1080)) -#define PERSEUS2_IO_CONF5 ((unsigned int)(0xFFFE1084)) -#define PERSEUS2_IO_CONF6 ((unsigned int)(0xFFFE1088)) -#define PERSEUS2_IO_CONF7 ((unsigned int)(0xFFFE108C)) -#define PERSEUS2_IO_CONF8 ((unsigned int)(0xFFFE1090)) -#define PERSEUS2_IO_CONF9 ((unsigned int)(0xFFFE1094)) -#define PERSEUS2_IO_CONF10 ((unsigned int)(0xFFFE1098)) -#define PERSEUS2_IO_CONF11 ((unsigned int)(0xFFFE109C)) -#define PERSEUS2_IO_CONF12 ((unsigned int)(0xFFFE10A0)) -#define PERSEUS2_IO_CONF13 ((unsigned int)(0xFFFE10A4)) -#define PERSEUS_PCC_CONF_REG ((unsigned int)(0xFFFE10B4)) -#define BIST_STATUS_INTERNAL ((unsigned int)(0xFFFE10B8)) -#define BIST_CONTROL ((unsigned int)(0xFFFE10C0)) -#define BOOT_ROM_REG ((unsigned int)(0xFFFE10C4)) -#define PRODUCTION_ID_REG ((unsigned int)(0xFFFE10C8)) -#define BIST_SECROM_SIGNATURE1_INTERNAL ((unsigned int)(0xFFFE10D0)) -#define BIST_SECROM_SIGNATURE2_INTERNAL ((unsigned int)(0xFFFE10D4)) -#define BIST_CONTROL_2 ((unsigned int)(0xFFFE10D8)) -#define DEBUG1 ((unsigned int)(0xFFFE10E0)) -#define DEBUG2 ((unsigned int)(0xFFFE10E4)) -#define DEBUG_DMA_IRQ ((unsigned int)(0xFFFE10E8)) - -/*************************************************************************** - * OMAP730 EMIFS Registers (TRM 2.5.7) - **************************************************************************/ - -#define TCMIF_BASE 0xFFFECC00 - -#define EMIFS_LRUREG (TCMIF_BASE + 0x04) -#define EMIFS_CONFIG (TCMIF_BASE + 0x0C) -#define FLASH_CFG_0 (TCMIF_BASE + 0x10) -#define FLASH_CFG_1 (TCMIF_BASE + 0x14) -#define FLASH_CFG_2 (TCMIF_BASE + 0x18) -#define FLASH_CFG_3 (TCMIF_BASE + 0x1C) -#define FL_CFG_DYN_WAIT (TCMIF_BASE + 0x40) -#define EMIFS_TIMEOUT1_REG (TCMIF_BASE + 0x28) -#define EMIFS_TIMEOUT2_REG (TCMIF_BASE + 0x2C) -#define EMIFS_TIMEOUT3_REG (TCMIF_BASE + 0x30) -#define EMIFS_ABORT_ADDR (TCMIF_BASE + 0x44) -#define EMIFS_ABORT_TYPE (TCMIF_BASE + 0x48) -#define EMIFS_ABORT_TOUT (TCMIF_BASE + 0x4C) -#define FLASH_ACFG_0_1 (TCMIF_BASE + 0x50) -#define FLASH_ACFG_1_1 (TCMIF_BASE + 0x54) -#define FLASH_ACFG_2_1 (TCMIF_BASE + 0x58) -#define FLASH_ACFG_3_1 (TCMIF_BASE + 0x5C) - -/*************************************************************************** - * OMAP730 Interrupt handlers - **************************************************************************/ - -#define OMAP_IH1_BASE 0xFFFECB00 /* MPU Level 1 IRQ handler */ -#define OMAP_IH2_BASE 0xfffe0000 - -/*************************************************************************** - * OMAP730 Timers - * - * There are three general purpose OS timers in the 730 that can be - * configured in autoreload or one-shot modes. - **************************************************************************/ - -#define OMAP730_32kHz_TIMER_BASE 0xFFFB9000 - -/* 32k Timer Registers */ -#define TIMER32k_CR 0x08 -#define TIMER32k_TVR 0x00 -#define TIMER32k_TCR 0x04 - -/* 32k Timer Control Register definition */ -#define TIMER32k_TSS (1<<0) -#define TIMER32k_TRB (1<<1) -#define TIMER32k_INT (1<<2) -#define TIMER32k_ARL (1<<3) - -/* MPU Timer base addresses */ -#define OMAP730_MPUTIMER_BASE 0xfffec500 -#define OMAP730_MPUTIMER_OFF 0x00000100 - -#define OMAP730_TIMER1_BASE 0xFFFEC500 -#define OMAP730_TIMER2_BASE 0xFFFEC600 -#define OMAP730_TIMER3_BASE 0xFFFEC700 - -/* MPU Timer Register offsets */ -#define CNTL_TIMER 0x00 /* MPU_CNTL_TIMER */ -#define LOAD_TIM 0x04 /* MPU_LOAD_TIMER */ -#define READ_TIM 0x08 /* MPU_READ_TIMER */ - -/* MPU_CNTL_TIMER register bits */ -#define MPUTIM_FREE (1<<6) -#define MPUTIM_CLOCK_ENABLE (1<<5) -#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT) -#define MPUTIM_PTV_BIT 2 -#define MPUTIM_AR (1<<1) -#define MPUTIM_ST (1<<0) - -/*************************************************************************** - * OMAP730 GPIO - * - * The GPIO control is split over 6 register bases in the OMAP730 to allow - * access to all the (6 x 32) GPIO pins! - **************************************************************************/ - -#define OMAP730_GPIO_BASE_1 0xFFFBC000 -#define OMAP730_GPIO_BASE_2 0xFFFBC800 -#define OMAP730_GPIO_BASE_3 0xFFFBD000 -#define OMAP730_GPIO_BASE_4 0xFFFBD800 -#define OMAP730_GPIO_BASE_5 0xFFFBE000 -#define OMAP730_GPIO_BASE_6 0xFFFBE800 - -#define GPIO_DATA_INPUT 0x00 -#define GPIO_DATA_OUTPUT 0x04 -#define GPIO_DIRECTION_CONTROL 0x08 -#define GPIO_INTERRUPT_CONTROL 0x0C -#define GPIO_INTERRUPT_MASK 0x10 -#define GPIO_INTERRUPT_STATUS 0x14 - -#define GPIO_DATA_INPUT_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_1 ((unsigned int)(OMAP730_GPIO_BASE_1 + GPIO_INTERRUPT_STATUS)) - -#define GPIO_DATA_INPUT_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_2 ((unsigned int)(OMAP730_GPIO_BASE_2 + GPIO_INTERRUPT_STATUS)) - -#define GPIO_DATA_INPUT_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_3 ((unsigned int)(OMAP730_GPIO_BASE_3 + GPIO_INTERRUPT_STATUS)) - -#define GPIO_DATA_INPUT_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_4 ((unsigned int)(OMAP730_GPIO_BASE_4 + GPIO_INTERRUPT_STATUS)) - -#define GPIO_DATA_INPUT_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_5 ((unsigned int)(OMAP730_GPIO_BASE_5 + GPIO_INTERRUPT_STATUS)) - -#define GPIO_DATA_INPUT_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DATA_INPUT)) -#define GPIO_DATA_OUTPUT_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DATA_OUTPUT)) -#define GPIO_DIRECTION_CONTROL_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_DIRECTION_CONTROL)) -#define GPIO_INTERRUPT_CONTROL_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_CONTROL)) -#define GPIO_INTERRUPT_MASK_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_MASK)) -#define GPIO_INTERRUPT_STATUS_6 ((unsigned int)(OMAP730_GPIO_BASE_6 + GPIO_INTERRUPT_STATUS)) - -/*************************************************************************** - * OMAP730 Watchdog timers - **************************************************************************/ - -#define WDTIM_BASE 0xFFFEC800 -#define WDTIM_CONTROL (WDTIM_BASE + 0x00) /* MPU_CNTL_TIMER */ -#define WDTIM_LOAD (WDTIM_BASE + 0x04) /* MPU_LOAD_TIMER */ -#define WDTIM_READ (WDTIM_BASE + 0x04) /* MPU_READ_TIMER */ -#define WDTIM_MODE (WDTIM_BASE + 0x08) /* MPU_TIMER_MODE */ - -/*************************************************************************** - * OMAP730 Interrupt Registers - **************************************************************************/ - -/* Interrupt Register offsets */ - -#define IRQ_ITR 0x00 -#define IRQ_MIR 0x04 -#define IRQ_SIR_IRQ 0x10 -#define IRQ_SIR_FIQ 0x14 -#define IRQ_CONTROL_REG 0x18 -#define IRQ_ILR0 0x1C /* ILRx == ILR0 + (0x4 * x) */ -#define IRQ_SIR 0x9C /* a.k.a.IRQ_ISR */ -#define IRQ_GMIR 0xA0 - -#define REG_IHL1_MIR (OMAP_IH1_BASE + IRQ_MIR) -#define REG_IHL2_MIR (OMAP_IH2_BASE + IRQ_MIR) - -/*************************************************************************** - * OMAP730 Intersystem Communication Register (TRM 4.5) - **************************************************************************/ - -#define ICR_BASE 0xFFFBB800 - -#define M_ICR (ICR_BASE + 0x00) -#define G_ICR (ICR_BASE + 0x02) -#define M_CTL (ICR_BASE + 0x04) -#define G_CTL (ICR_BASE + 0x06) -#define PM_BA (ICR_BASE + 0x0A) -#define DM_BA (ICR_BASE + 0x0C) -#define RM_BA (ICR_BASE + 0x0E) -#define SSPI_TAS (ICR_BASE + 0x12) - -#endif /* ! __INCLUDED_OMAP730_H */ diff --git a/include/configs/omap730p2.h b/include/configs/omap730p2.h deleted file mode 100644 index 947f27b..0000000 --- a/include/configs/omap730p2.h +++ /dev/null @@ -1,173 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * MPC Data Limited (http://www.mpc-data.co.uk) - * Dave Peverley <dpeverley at mpc-data.co.uk> - * - * Configuation settings for the TI OMAP Perseus 2 board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP730 1 /* which is in a 730 */ -#define CONFIG_P2_OMAP730 1 /* a Perseus 2 Board */ - -/* - * Input clock of PLL - * The OMAP730 Perseus 2 has 13MHz input clock - */ - -#define CONFIG_SYS_CLK_FREQ 13000000 - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 - -/* - * Size of malloc() pool - */ - -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* - * Hardware drivers - */ - -#define CONFIG_LAN91C96 -#define CONFIG_LAN91C96_BASE 0x04000300 -#define CONFIG_LAN91C96_EXT_PHY - -/* - * NS16550 Configuration - */ - -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (1) -#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */ -#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart - * on perseus */ - -/* - * select serial console configuration - */ - -#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP730 Perseus 2 */ - -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - - -#include <configs/omap730.h> -#include <configs/h2_p2_dbg_board.h> - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw ip=bootp" - -#define CONFIG_LOADADDR 0x10000000 - -#define CONFIG_ETHADDR -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 192.168.0.23 -#define CONFIG_SERVERIP 192.150.0.100 -#define CONFIG_BOOTFILE "uImage" /* File to load */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 115200 /* Speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 1 /* Which serial port to use */ -#endif - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "OMAP730 P2 # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */ - -/* The OMAP730 has 3 general purpose MPU timers, they can be driven by - * the RefClk (12Mhz) or by DPLL1. This time is further subdivided by a - * local divisor. - */ -#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */ -#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */ -#define CONFIG_SYS_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CONFIG_SYS_PTV)) - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ - -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ - -#if defined(CONFIG_CS0_BOOT) -#define PHYS_FLASH_1 0x0C000000 -#elif defined(CONFIG_CS3_BOOT) -#define PHYS_FLASH_1 0x00000000 -#else -#error Unknown Boot Chip-Select number -#endif - -#define PHYS_SRAM 0x20000000 - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */ -#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */ -/* addr of environment */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x020000) - -/* timeout values are in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_OFFSET 0x20000 /* environment starts here */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_SP_ADDR PHYS_SRAM - -#endif /* ! __CONFIG_H */ diff --git a/include/configs/otc570.h b/include/configs/otc570.h index 3f4e073..629967d 100644 --- a/include/configs/otc570.h +++ b/include/configs/otc570.h @@ -193,8 +193,8 @@ # define CONFIG_SYS_NAND_DBW_8 # define CONFIG_SYS_NAND_MASK_ALE (1 << 21) # define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -# define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 -# define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 22 +# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) +# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22) #endif /* Ethernet */ diff --git a/include/configs/pm9261.h b/include/configs/pm9261.h index fc95cf0..4a71927 100644 --- a/include/configs/pm9261.h +++ b/include/configs/pm9261.h @@ -50,15 +50,13 @@ #define CONFIG_SYS_MCKR1_VAL \ (AT91_PMC_MCKR_CSS_SLOW | \ AT91_PMC_MCKR_PRES_1 | \ - AT91_PMC_MCKR_MDIV_2 | \ - AT91_PMC_MCKR_PLLADIV_1) + AT91_PMC_MCKR_MDIV_2) /* PCK/2 = MCK Master Clock from PLLA */ #define CONFIG_SYS_MCKR2_VAL \ (AT91_PMC_MCKR_CSS_PLLA | \ AT91_PMC_MCKR_PRES_1 | \ - AT91_PMC_MCKR_MDIV_2 | \ - AT91_PMC_MCKR_PLLADIV_1) + AT91_PMC_MCKR_MDIV_2) /* define PDC[31:16] as DATA[31:16] */ #define CONFIG_SYS_PIOC_PDR_VAL1 0xFFFF0000 @@ -166,9 +164,9 @@ /* LED */ #define CONFIG_AT91_LED -#define CONFIG_RED_LED AT91_PIO_PORTC, 12 -#define CONFIG_GREEN_LED AT91_PIO_PORTC, 13 -#define CONFIG_YELLOW_LED AT91_PIO_PORTC, 15 +#define CONFIG_RED_LED GPIO_PIN_PC(12) +#define CONFIG_GREEN_LED GPIO_PIN_PC(13) +#define CONFIG_YELLOW_LED GPIO_PIN_PC(15) #define CONFIG_BOOTDELAY 3 @@ -221,8 +219,8 @@ #define CONFIG_SYS_NAND_MASK_ALE (1 << 22) /* our CLE is AD21 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 21) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTA, 16 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(16) /* NOR flash */ #define CONFIG_SYS_FLASH_CFI 1 diff --git a/include/configs/pm9263.h b/include/configs/pm9263.h index 533e249..d9c04d1 100644 --- a/include/configs/pm9263.h +++ b/include/configs/pm9263.h @@ -179,8 +179,8 @@ /* LED */ #define CONFIG_AT91_LED -#define CONFIG_RED_LED AT91_PIO_PORTB, 7 /* this is the power led */ -#define CONFIG_GREEN_LED AT91_PIO_PORTB, 8 /* this is the user1 led */ +#define CONFIG_RED_LED GPIO_PIN_PB(7) /* this is the power led */ +#define CONFIG_GREEN_LED GPIO_PIN_PB(8) /* this is the user1 led */ #define CONFIG_BOOTDELAY 3 @@ -241,8 +241,8 @@ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTB, 30 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PB(30) #endif diff --git a/include/configs/pm9g45.h b/include/configs/pm9g45.h index e0c388e..f78e0ec 100644 --- a/include/configs/pm9g45.h +++ b/include/configs/pm9g45.h @@ -54,8 +54,8 @@ /* LED */ #define CONFIG_AT91_LED -#define CONFIG_RED_LED AT91_PIO_PORTD, 31 /* this is the user1 led */ -#define CONFIG_GREEN_LED AT91_PIO_PORTD, 0 /* this is the user2 led */ +#define CONFIG_RED_LED GPIO_PIN_PD(31) /* this is the user1 led */ +#define CONFIG_GREEN_LED GPIO_PIN_PD(0) /* this is the user2 led */ #define CONFIG_BOOTDELAY 3 @@ -106,8 +106,8 @@ #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our CLE is AD22 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTC, 14 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTD, 3 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PD(3) #endif diff --git a/include/configs/pxm2.h b/include/configs/pxm2.h index 20b0f9a..7722f7b 100644 --- a/include/configs/pxm2.h +++ b/include/configs/pxm2.h @@ -70,6 +70,7 @@ "hostname=pxm2\0" \ "nand_img_size=0x500000\0" \ "optargs=\0" \ + "splashpos=m,m\0" \ CONFIG_COMMON_ENV_SETTINGS \ "mmc_dev=0\0" \ "mmc_root=/dev/mmcblk0p2 rw\0" \ @@ -118,9 +119,7 @@ "fi;" \ "fi;" \ "run nand_boot;" \ - "if ping ${serverip}; then " \ - "run net_nfs; " \ - "fi; " + "reset;" #else #define CONFIG_BOOTDELAY 0 @@ -148,6 +147,8 @@ #define DA8XX_LCD_CNTL_BASE LCD_CNTL_BASE #define PWM_TICKS 0x1388 #define PWM_DUTY 0x200 +#define CONFIG_SYS_CONSOLE_BG_COL 0xff +#define CONFIG_SYS_CONSOLE_FG_COL 0x00 #endif #endif /* ! __CONFIG_PXM2_H */ diff --git a/include/configs/rut.h b/include/configs/rut.h index 7c94644..d4519f9 100644 --- a/include/configs/rut.h +++ b/include/configs/rut.h @@ -65,7 +65,8 @@ /* Default env settings */ #define CONFIG_EXTRA_ENV_SETTINGS \ "hostname=rut\0" \ - "splashpos=488,352\0" \ + "nand_img_size=0x500000\0" \ + "splashpos=m,m\0" \ "optargs=fixrtc --no-log consoleblank=0 \0" \ CONFIG_COMMON_ENV_SETTINGS \ "mmc_dev=0\0" \ @@ -111,9 +112,7 @@ "fi;" \ "fi;" \ "run nand_boot;" \ - "if ping ${serverip}; then " \ - "run net_nfs; " \ - "fi; " + "reset;" #else #define CONFIG_BOOTDELAY 0 @@ -151,6 +150,9 @@ #define BOARD_LCD_RESET 115 /* Bank 3 pin 19 */ #define CONFIG_ARCH_EARLY_INIT_R #define CONFIG_FORMIKE +#define DISPL_PLL_SPREAD_SPECTRUM +#define CONFIG_SYS_CONSOLE_BG_COL 0xff +#define CONFIG_SYS_CONSOLE_FG_COL 0x00 #endif #endif /* ! __CONFIG_RUT_H */ diff --git a/include/configs/sama5d3xek.h b/include/configs/sama5d3xek.h index 5a6f0fc..c34feb5 100644 --- a/include/configs/sama5d3xek.h +++ b/include/configs/sama5d3xek.h @@ -24,7 +24,10 @@ #define CONFIG_AT91FAMILY #define CONFIG_ARCH_CPU_INIT +#ifndef CONFIG_SPL_BUILD #define CONFIG_SKIP_LOWLEVEL_INIT +#endif + #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_DISPLAY_CPUINFO @@ -93,8 +96,12 @@ #define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS #define CONFIG_SYS_SDRAM_SIZE 0x20000000 +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_INIT_SP_ADDR 0x310000 +#else #define CONFIG_SYS_INIT_SP_ADDR \ (CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE) +#endif /* SerialFlash */ #define CONFIG_CMD_SF @@ -235,4 +242,31 @@ /* Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) +/* SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_TEXT_BASE 0x300000 +#define CONFIG_SPL_MAX_SIZE 0x10000 +#define CONFIG_SPL_BSS_START_ADDR 0x20000000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 +#define CONFIG_SYS_SPL_MALLOC_START 0x20080000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 + +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT + +#define CONFIG_SPL_BOARD_INIT +#ifdef CONFIG_SYS_USE_MMC +#define CONFIG_SPL_LDSCRIPT arch/arm/cpu/at91-common/u-boot-spl.lds +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400 +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#endif + #endif diff --git a/include/configs/sbc35_a9g20.h b/include/configs/sbc35_a9g20.h index cbcd4e1..7e16c45 100644 --- a/include/configs/sbc35_a9g20.h +++ b/include/configs/sbc35_a9g20.h @@ -115,6 +115,7 @@ #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_RESET_PHY_R #define CONFIG_MACB_SEARCH_PHY +#define CONFIG_AT91_WANTS_COMMON_PHY /* USB */ #define CONFIG_USB_ATMEL diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h index f37653f..4569fd4 100644 --- a/include/configs/siemens-am33x-common.h +++ b/include/configs/siemens-am33x-common.h @@ -254,11 +254,11 @@ #define CONFIG_USB_GADGET #define CONFIG_USBDOWNLOAD_GADGET -/* USB TI's IDs */ +/* USB DRACO ID as default */ #define CONFIG_USBD_HS -#define CONFIG_G_DNL_VENDOR_NUM 0x0525 -#define CONFIG_G_DNL_PRODUCT_NUM 0x4a47 -#define CONFIG_G_DNL_MANUFACTURER "Texas Instruments" +#define CONFIG_G_DNL_VENDOR_NUM 0x0908 +#define CONFIG_G_DNL_PRODUCT_NUM 0x02d2 +#define CONFIG_G_DNL_MANUFACTURER "Siemens AG" /* USB Device Firmware Update support */ #define CONFIG_DFU_FUNCTION @@ -358,31 +358,38 @@ #define CONFIG_COMMON_ENV_SETTINGS \ "verify=no \0" \ "project_dir=systemone\0" \ + "upgrade_available=0\0" \ + "altbootcmd=run bootcmd\0" \ + "bootlimit=3\0" \ + "partitionset_active=A\0" \ "loadaddr=0x82000000\0" \ "kloadaddr=0x81000000\0" \ "script_addr=0x81900000\0" \ - "console=console=ttyMTD,mtdoops console=ttyO0,115200n8\0" \ - "active_set=a\0" \ + "console=console=ttyMTD,mtdoops console=ttyO0,115200n8 panic=5\0" \ "nand_active_ubi_vol=rootfs_a\0" \ + "nand_active_ubi_vol_A=rootfs_a\0" \ + "nand_active_ubi_vol_B=rootfs_b\0" \ "nand_root_fs_type=ubifs rootwait=1\0" \ "nand_src_addr=0x280000\0" \ - "nand_src_addr_a=0x280000\0" \ - "nand_src_addr_b=0x780000\0" \ + "nand_src_addr_A=0x280000\0" \ + "nand_src_addr_B=0x780000\0" \ "nfsopts=nolock rw mem=128M\0" \ "ip_method=none\0" \ "bootenv=uEnv.txt\0" \ "bootargs_defaults=setenv bootargs " \ "console=${console} " \ + "${testargs} " \ "${optargs}\0" \ "nand_args=run bootargs_defaults;" \ "mtdparts default;" \ - "setenv nand_active_ubi_vol rootfs_${active_set};" \ - "setenv ${active_set} true;" \ - "if test -n ${a}; then " \ - "setenv nand_src_addr ${nand_src_addr_a};" \ + "setenv ${partitionset_active} true;" \ + "if test -n ${A}; then " \ + "setenv nand_active_ubi_vol ${nand_active_ubi_vol_A};" \ + "setenv nand_src_addr ${nand_src_addr_A};" \ "fi;" \ - "if test -n ${b}; then " \ - "setenv nand_src_addr ${nand_src_addr_b};" \ + "if test -n ${B}; then " \ + "setenv nand_active_ubi_vol ${nand_active_ubi_vol_B};" \ + "setenv nand_src_addr ${nand_src_addr_B};" \ "fi;" \ "setenv nand_root ubi0:${nand_active_ubi_vol} rw " \ "ubi.mtd=9,2048;" \ @@ -403,9 +410,26 @@ "setenv bootargs ${bootargs} " \ "root=/dev/nfs ${mtdparts} " \ "nfsroot=${serverip}:${rootpath},${nfsopts} " \ - "addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:" \ + "ip=${ipaddr}:${serverip}:" \ "${gatewayip}:${netmask}:${hostname}:eth0:off\0" \ - "nand_boot=echo Booting from nand, active set ${active_set} ...; " \ + "nand_boot=echo Booting from nand; " \ + "if test ${upgrade_available} -eq 1; then " \ + "if test ${bootcount} -gt ${bootlimit}; " \ + "then " \ + "setenv upgrade_available 0;" \ + "setenv ${partitionset_active} true;" \ + "if test -n ${A}; then " \ + "setenv partitionset_active B; " \ + "env delete A; " \ + "fi;" \ + "if test -n ${B}; then " \ + "setenv partitionset_active A; " \ + "env delete B; " \ + "fi;" \ + "saveenv; " \ + "fi;" \ + "fi;" \ + "echo set ${partitionset_active}...;" \ "run nand_args; " \ "nand read.i ${kloadaddr} ${nand_src_addr} " \ "${nand_img_size}; bootm ${kloadaddr}\0" \ @@ -414,7 +438,7 @@ "tftpboot ${kloadaddr} ${serverip}:${bootfile}; " \ "bootm ${kloadaddr}\0" \ "flash_self=run nand_boot\0" \ - "flash_self_test=setenv bootargs_defaults ${bootargs_defaults} test; " \ + "flash_self_test=setenv testargs test; " \ "run nand_boot\0" \ "dfu_start=echo Preparing for dfu mode ...; " \ "run dfu_args; \0" \ @@ -425,8 +449,9 @@ "mode; echo Not ready yet: 'run flash_nfs' to use kernel " \ "from memory and root filesystem over NFS; echo Type " \ "'run net_nfs' to get Kernel over TFTP and mount root " \ - "filesystem over NFS; echo Set active_set variable to 'a' " \ - "or 'b' to select kernel and rootfs partition; " \ + "filesystem over NFS; " \ + "echo Set partitionset_active variable to 'A' " \ + "or 'B' to select kernel and rootfs partition; " \ "echo" \ "\0" @@ -457,4 +482,15 @@ #define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds, " \ "press \"<Esc><Esc>\" to stop\n", bootdelay +/* Reboot after 60 sec if bootcmd fails */ +#define CONFIG_RESET_TO_RETRY +#define CONFIG_BOOT_RETRY_TIME 60 + +#define CONFIG_BOOTCOUNT_LIMIT +#define CONFIG_BOOTCOUNT_ENV + +/* Enable Device-Tree (FDT) support */ +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_FDT + #endif /* ! __CONFIG_SIEMENS_AM33X_COMMON_H */ diff --git a/include/configs/snapper9260.h b/include/configs/snapper9260.h index 5436bae..94a65c4 100644 --- a/include/configs/snapper9260.h +++ b/include/configs/snapper9260.h @@ -59,6 +59,7 @@ #define CONFIG_RMII #define CONFIG_NET_RETRY_COUNT 20 #define CONFIG_RESET_PHY_R +#define CONFIG_AT91_WANTS_COMMON_PHY #define CONFIG_TFTP_PORT #define CONFIG_TFTP_TSIZE @@ -74,7 +75,6 @@ #define CONFIG_USB_STORAGE /* GPIOs and IO expander */ -#define CONFIG_AT91_LEGACY #define CONFIG_ATMEL_LEGACY #define CONFIG_AT91_GPIO #define CONFIG_AT91_GPIO_PULLUP 1 diff --git a/include/configs/stamp9g20.h b/include/configs/stamp9g20.h index 248e657..51339b1 100644 --- a/include/configs/stamp9g20.h +++ b/include/configs/stamp9g20.h @@ -145,6 +145,7 @@ #ifdef CONFIG_MACB # define CONFIG_RMII /* use reduced MII inteface */ # define CONFIG_NET_RETRY_COUNT 20 /* # of DHCP/BOOTP retries */ +#define CONFIG_AT91_WANTS_COMMON_PHY /* BOOTP and DHCP options */ # define CONFIG_BOOTP_BOOTFILESIZE diff --git a/include/configs/taurus.h b/include/configs/taurus.h new file mode 100644 index 0000000..c980023 --- /dev/null +++ b/include/configs/taurus.h @@ -0,0 +1,160 @@ +/* + * Common board functions for Siemens TAURUS (AT91SAM9G20) based boards + * (C) Copyright 2013 Siemens AG + * + * Based on: + * U-Boot file: include/configs/at91sam9260ek.h + * + * (C) Copyright 2007-2008 + * Stelian Pop <stelian@popies.net> + * Lead Tech Design <www.leadtechdesign.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * SoC must be defined first, before hardware.h is included. + * In this case SoC is defined in boards.cfg. + */ +#include <asm/hardware.h> + +#define MACH_TYPE_TAURUS 2067 +#define MACH_TYPE_AXM 2068 + +/* + * Warning: changing CONFIG_SYS_TEXT_BASE requires + * adapting the initial boot program. + * Since the linker has to swallow that define, we must use a pure + * hex number here! + */ + + +#define CONFIG_SYS_TEXT_BASE 0x23f00000 + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */ +#define CONFIG_SYS_HZ 1000 + +/* Misc CPU related */ +#define CONFIG_ARCH_CPU_INIT +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_SKIP_LOWLEVEL_INIT +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_CMD_BOOTZ +#define CONFIG_OF_LIBFDT + +/* general purpose I/O */ +#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */ +#define CONFIG_AT91_GPIO +#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */ + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_BOOTDELAY 3 + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_SOURCE + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NAND + +/* + * SDRAM: 1 bank, min 32, max 128 MB + * Initialized before u-boot gets started. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) + +/* + * Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM, + * leaving the correct space for initial global data structure above + * that address while providing maximum stack area below. + */ +# define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) + +/* NAND flash */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +#define CONFIG_SYS_NAND_DBW_8 +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14 +#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC13 +#endif + +/* NOR flash - no real flash on this board */ +#define CONFIG_SYS_NO_FLASH 1 + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_AT91_WANTS_COMMON_PHY + +/* USB */ +#if defined(CONFIG_BOARD_TAURUS) +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE +#endif + +/* load address */ +#define CONFIG_SYS_LOAD_ADDR 0x22000000 + +/* bootstrap in spi flash , u-boot + env + linux in nandflash */ +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x100000 +#define CONFIG_ENV_OFFSET_REDUND 0x180000 +#define CONFIG_ENV_SIZE 0x20000 /* 1 sector = 128 kB */ +#define CONFIG_BOOTCOMMAND "nand read 0x22000000 0x200000 0x300000; bootm" +#define CONFIG_BOOTARGS \ + "console=ttyS0,115200 earlyprintk " \ + "mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro," \ + "256k(env),256k(env_redundant),256k(spare)," \ + "512k(dtb),6M(kernel)ro,-(rootfs) " \ + "root=/dev/mtdblock7 rw rootfstype=jffs2" + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_LONGHELP +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN \ + ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) + +#endif diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 10fe47f..4364eef 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -18,6 +18,7 @@ #define CONFIG_SYS_CACHELINE_SIZE 64 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ #define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ +#define CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC #include <asm/arch/omap.h> @@ -42,9 +43,9 @@ /* * RTC related defines. To use bootcount you must set bootlimit in the - * environment to a non-zero value. + * environment to a non-zero value and enable CONFIG_BOOTCOUNT_LIMIT + * in the board config. */ -#define CONFIG_BOOTCOUNT_LIMIT #define CONFIG_SYS_BOOTCOUNT_ADDR 0x44E3E000 /* Enable the HW watchdog, since we can use this with bootcount */ diff --git a/include/configs/trats.h b/include/configs/trats.h index f163303..0877142 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -299,6 +299,7 @@ #define CONFIG_USB_GADGET_S3C_UDC_OTG #define CONFIG_USB_GADGET_DUALSPEED #define CONFIG_USB_GADGET_VBUS_DRAW 2 +#define CONFIG_USB_CABLE_CHECK /* LCD */ #define CONFIG_EXYNOS_FB diff --git a/include/configs/trats2.h b/include/configs/trats2.h index 3bcdfb1..5d86a3d 100644 --- a/include/configs/trats2.h +++ b/include/configs/trats2.h @@ -20,8 +20,6 @@ #define CONFIG_EXYNOS4 /* which is in a EXYNOS4XXX */ #define CONFIG_TIZEN /* TIZEN lib */ -#define PLATFORM_NO_UNALIGNED - #include <asm/arch/cpu.h> /* get chip and board defs */ #define CONFIG_ARCH_CPU_INIT @@ -65,10 +63,9 @@ #define CONFIG_DISPLAY_CPUINFO -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (2 << 20)) +#include <asm/sizes.h> +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (80 * SZ_1M)) /* select serial console configuration */ #define CONFIG_SERIAL2 @@ -100,6 +97,7 @@ #define CONFIG_CMD_CACHE #define CONFIG_CMD_I2C #define CONFIG_CMD_MMC +#define CONFIG_CMD_DFU #define CONFIG_CMD_GPT #define CONFIG_CMD_PMIC @@ -113,6 +111,23 @@ #define CONFIG_CMD_EXT4 #define CONFIG_CMD_EXT4_WRITE +/* USB Composite download gadget - g_dnl */ +#define CONFIG_USBDOWNLOAD_GADGET +#define CONFIG_SYS_DFU_DATA_BUF_SIZE SZ_32M +#define CONFIG_DFU_FUNCTION +#define CONFIG_DFU_MMC + +/* TIZEN THOR downloader support */ +#define CONFIG_CMD_THOR_DOWNLOAD +#define CONFIG_THOR_FUNCTION + +/* USB Samsung's IDs */ +#define CONFIG_G_DNL_VENDOR_NUM 0x04E8 +#define CONFIG_G_DNL_PRODUCT_NUM 0x6601 +#define CONFIG_G_DNL_THOR_VENDOR_NUM CONFIG_G_DNL_VENDOR_NUM +#define CONFIG_G_DNL_THOR_PRODUCT_NUM 0x685D +#define CONFIG_G_DNL_MANUFACTURER "Samsung" + /* To use the TFTPBOOT over USB, Please enable the CONFIG_CMD_NET */ #undef CONFIG_CMD_NET @@ -136,25 +151,29 @@ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Tizen - partitions definitions */ -#define PARTS_CSA "csa-mmc" -#define PARTS_BOOTLOADER "u-boot" +#define PARTS_CSA "csa" #define PARTS_BOOT "boot" +#define PARTS_MODEM "modem" +#define PARTS_CSC "csc" #define PARTS_ROOT "platform" #define PARTS_DATA "data" -#define PARTS_CSC "csc" #define PARTS_UMS "ums" #define PARTS_DEFAULT \ - "uuid_disk=${uuid_gpt_disk};" \ - "name="PARTS_CSA",size=8MiB,uuid=${uuid_gpt_"PARTS_CSA"};" \ - "name="PARTS_BOOTLOADER",size=60MiB," \ - "uuid=${uuid_gpt_"PARTS_BOOTLOADER"};" \ - "name="PARTS_BOOT",size=100MiB,uuid=${uuid_gpt_"PARTS_BOOT"};" \ - "name="PARTS_ROOT",size=1GiB,uuid=${uuid_gpt_"PARTS_ROOT"};" \ - "name="PARTS_DATA",size=3GiB,uuid=${uuid_gpt_"PARTS_DATA"};" \ + "name="PARTS_CSA",start=5MiB,size=8MiB,uuid=${uuid_gpt_"PARTS_CSA"};" \ + "name="PARTS_BOOT",size=64MiB,uuid=${uuid_gpt_"PARTS_BOOT"};" \ + "name="PARTS_MODEM",size=100MiB,uuid=${uuid_gpt_"PARTS_MODEM"};" \ "name="PARTS_CSC",size=150MiB,uuid=${uuid_gpt_"PARTS_CSC"};" \ + "name="PARTS_ROOT",size=1536MiB,uuid=${uuid_gpt_"PARTS_ROOT"};" \ + "name="PARTS_DATA",size=512MiB,uuid=${uuid_gpt_"PARTS_DATA"};" \ "name="PARTS_UMS",size=-,uuid=${uuid_gpt_"PARTS_UMS"}\0" \ +#define CONFIG_DFU_ALT \ + "u-boot mmc 80 800;" \ + "uImage ext4 0 2;" \ + "exynos4412-trats2.dtb ext4 0 2;" \ + ""PARTS_ROOT" part 0 5\0" + #define CONFIG_EXTRA_ENV_SETTINGS \ "bootk=" \ "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ @@ -178,15 +197,16 @@ "rootfstype=ext4\0" \ "console=" CONFIG_DEFAULT_CONSOLE \ "kernelname=uImage\0" \ - "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \ - "0x40007FC0 ${kernelname}\0" \ + "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 " \ + "${kernelname}\0" \ "loaddtb=ext4load mmc ${mmcdev}:${mmcbootpart} ${fdtaddr} " \ "${fdtfile}\0" \ - "mmcdev=0\0" \ + "mmcdev=CONFIG_MMC_DEFAULT_DEV\0" \ "mmcbootpart=2\0" \ "mmcrootpart=5\0" \ "opts=always_resume=1\0" \ "partitions=" PARTS_DEFAULT \ + "dfu_alt_info=" CONFIG_DFU_ALT \ "uartpath=ap\0" \ "usbpath=ap\0" \ "consoleon=set console console=ttySAC2,115200n8; save; reset\0" \ @@ -233,8 +253,6 @@ #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_HZ 1000 - /* valid baudrates */ #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -288,6 +306,11 @@ int get_soft_i2c_sda_pin(void); #define CONFIG_POWER_MUIC_MAX77693 #define CONFIG_POWER_FG_MAX77693 #define CONFIG_POWER_BATTERY_TRATS2 +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_S3C_UDC_OTG +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_VBUS_DRAW 2 +#define CONFIG_USB_CABLE_CHECK /* LCD */ #define CONFIG_EXYNOS_FB @@ -300,6 +323,9 @@ int get_soft_i2c_sda_pin(void); #define CONFIG_VIDEO_BMP_GZIP #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE ((500 * 250 * 4) + (1 << 12)) +#define CONFIG_CMD_USB_MASS_STORAGE +#define CONFIG_USB_GADGET_MASS_STORAGE + /* Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 diff --git a/include/configs/usb_a9263.h b/include/configs/usb_a9263.h new file mode 100644 index 0000000..c4d04de --- /dev/null +++ b/include/configs/usb_a9263.h @@ -0,0 +1,169 @@ +/* + * (C) Copyright 2007-2013 + * Stelian Pop <stelian.pop@leadtechdesign.com> + * Lead Tech Design <www.leadtechdesign.com> + * Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com> + * Mateusz Kulikowski <mateusz.kulikowski@gmail.com> + * + * Settings for Calao USB-A9263 board + * + * U-Boot image has to be less than 200704 bytes, otherwise at91bootstrap + * installed on board will not be able to load it properly. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_H +#define __CONFIG_H +#include <asm/hardware.h> + +/* ARM asynchronous clock */ +#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */ +#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_MACH_TYPE MACH_TYPE_USB_A9263 + +#define CONFIG_ARCH_CPU_INIT + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG + +#define CONFIG_SKIP_LOWLEVEL_INIT + +#define CONFIG_DISPLAY_CPUINFO + +#define CONFIG_OF_LIBFDT +#define CONFIG_SYS_GENERIC_BOARD +#define CONFIG_SYS_TEXT_BASE 0x23f00000 + +/* + * Hardware drivers + */ +#define CONFIG_AT91_GPIO + +/* serial console */ +#define CONFIG_ATMEL_USART +#define CONFIG_USART_BASE ATMEL_BASE_DBGU +#define CONFIG_USART_ID ATMEL_ID_SYS +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_BOOTDELAY 3 + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> +#undef CONFIG_CMD_BDI +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_IMLS +#undef CONFIG_CMD_ITEST +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_LOADS + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_NAND + +/* SDRAM */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1 +#define CONFIG_SYS_SDRAM_SIZE 0x04000000 + +#define CONFIG_SYS_INIT_SP_ADDR \ + (ATMEL_BASE_SRAM1 + 0x1000 - GENERATED_GBL_DATA_SIZE) + +/* DataFlash */ +#define CONFIG_ATMEL_DATAFLASH_SPI +#define CONFIG_HAS_DATAFLASH +#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ) +#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1 +#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 +#define AT91_SPI_CLK 8000000 +#define DATAFLASH_TCSS (0x1a << 16) +#define DATAFLASH_TCHS (0x1 << 24) + +/* no NOR flash */ +#define CONFIG_SYS_NO_FLASH + +/* NAND flash */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_ATMEL +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 +/* our ALE is AD21 */ +#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) +/* our CLE is AD22 */ +#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22) +#endif + +#define MTDPARTS_DEFAULT \ + "mtdparts=atmel_nand:16m(kernel)ro,120m(root1),-(root2)" + +/* Ethernet */ +#define CONFIG_MACB +#define CONFIG_RMII +#define CONFIG_NET_RETRY_COUNT 20 +#define CONFIG_AT91_WANTS_COMMON_PHY + +/* USB */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_ATMEL +#define CONFIG_USB_OHCI_NEW +#define CONFIG_DOS_PARTITION +#define CONFIG_SYS_USB_OHCI_CPU_INIT +#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000 +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2 +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_FAT +#endif + +#define CONFIG_SYS_LOAD_ADDR 0x22000000 + +#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END 0x23e00000 + +/* bootstrap + u-boot + env in dataflash on CS0 */ +#define CONFIG_ENV_IS_IN_DATAFLASH +#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + 0x4000) +#define CONFIG_ENV_OFFSET 0x2000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS0 + \ + CONFIG_ENV_OFFSET) +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_BOOTCOMMAND "nboot 21000000 0" +#define CONFIG_BOOTARGS "console=ttyS0,115200 " \ + "root=/dev/mtdblock1 " \ + "mtdparts=" MTDPARTS_DEFAULT " " \ + "rw rootfstype=jffs2" +#define CONFIG_EXTRA_ENV_SETTINGS \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + +#define CONFIG_SYS_PROMPT "U-Boot> " +#define CONFIG_SYS_CBSIZE 256 +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_CMDLINE_EDITING +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_LONGHELP + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000) + +#endif diff --git a/include/configs/vexpress_common.h b/include/configs/vexpress_common.h index 6da5e8f..7e78f8a 100644 --- a/include/configs/vexpress_common.h +++ b/include/configs/vexpress_common.h @@ -132,7 +132,7 @@ #define VEXPRESS_FLASHPROG_FLVPPEN (1 << 0) #define CONFIG_SYS_TIMER_RATE 1000000 -#define CONFIG_SYS_TIMER_COUNTER (0x10011000 + 0x4) +#define CONFIG_SYS_TIMER_COUNTER (V2M_TIMER01 + 0x4) #define CONFIG_SYS_TIMER_COUNTS_DOWN /* SMSC9115 Ethernet from SMSC9118 family */ diff --git a/include/configs/vl_ma2sc.h b/include/configs/vl_ma2sc.h index 1489080..88aaa95 100644 --- a/include/configs/vl_ma2sc.h +++ b/include/configs/vl_ma2sc.h @@ -320,8 +320,8 @@ #define CONFIG_SYS_NAND_DBW_8 1 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* our ALE is AD21 */ #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* our CLE is AD22 */ -#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIO_PORTD, 15 -#define CONFIG_SYS_NAND_READY_PIN AT91_PIO_PORTB, 0 +#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15) +#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PB(0) #define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */ #endif @@ -330,6 +330,7 @@ #define CONFIG_RMII #define CONFIG_NET_MULTI #define CONFIG_NET_RETRY_COUNT 5 +#define CONFIG_AT91_WANTS_COMMON_PHY #define CONFIG_OVERWRITE_ETHADDR_ONCE |