diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/lwmon.h | 18 | ||||
| -rw-r--r-- | include/configs/omap1510.h | 687 | ||||
| -rw-r--r-- | include/configs/omap1510inn.h | 170 |
3 files changed, 870 insertions, 5 deletions
diff --git a/include/configs/lwmon.h b/include/configs/lwmon.h index d427d80..717ba35 100644 --- a/include/configs/lwmon.h +++ b/include/configs/lwmon.h @@ -220,6 +220,19 @@ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #endif +/*----------------------------------------------------------------------*/ +#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */ +#undef CONFIG_MODEM_SUPPORT_DEBUG + +#define CONFIG_MODEM_KEY_MAGIC "3C+3F" /* press F3 + F6 keys to enable modem */ +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ +#if 0 +#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n" +#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ +#endif +/*----------------------------------------------------------------------*/ + /* * Low Level Configuration Settings * (address mappings, register initial values, etc.) @@ -576,9 +589,4 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */ -#undef CONFIG_MODEM_SUPPORT_DEBUG - -#define CONFIG_MODEM_KEY_MAGIC "3C+3F" /* press F3 + F6 keys to enable modem */ -#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ #endif /* __CONFIG_H */ diff --git a/include/configs/omap1510.h b/include/configs/omap1510.h new file mode 100644 index 0000000..001e21a --- /dev/null +++ b/include/configs/omap1510.h @@ -0,0 +1,687 @@ +/* + * + * BRIEF MODULE DESCRIPTION + * OMAP hardware map + * + * Copyright (C) 2001 RidgeRun, Inc. (http://www.ridgerun.com) + * Author: RidgeRun, Inc. + * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <asm/arch/sizes.h> + +/* + There are 2 sets of general I/O --> + 1. GPIO (shared between ARM & DSP, configured by ARM) + 2. MPUIO which can be used only by the ARM. + + Base address FFFB:5000 is where the ARM accesses the MPUIO control registers + (see 7.2.2 of the TRM for MPUIO reg definitions). + + Base address E101:5000 is reserved for ARM access of the same MPUIO control + regs, but via the DSP I/O map. This address is unavailable on 1510. + + Base address FFFC:E000 is where the ARM accesses the GPIO config registers + directly via its own peripheral bus. + + Base address E101:E000 is where the ARM can access the same GPIO config + registers, but the access takes place through the ARM port interface (called + API or MPUI) via the DSP's peripheral bus (DSP I/O space). + + Therefore, the ARM should setup the GPIO regs thru the FFFC:E000 addresses + instead of the E101:E000 addresses. The DSP has only read access of the pin + control register, so this may explain the inability to write to E101:E018. + Try accessing pin control reg at FFFC:E018. + */ +#define OMAP1510_GPIO_BASE 0xfffce000 +#define OMAP1510_GPIO_START OMAP1510_GPIO_BASE +#define OMAP1510_GPIO_SIZE SZ_4K + +#define OMAP1510_MCBSP1_BASE 0xE1011000 +#define OMAP1510_MCBSP1_SIZE SZ_4K +#define OMAP1510_MCBSP1_START 0xE1011000 + +#define OMAP1510_MCBSP2_BASE 0xFFFB1000 + +#define OMAP1510_MCBSP3_BASE 0xE1017000 +#define OMAP1510_MCBSP3_SIZE SZ_4K +#define OMAP1510_MCBSP3_START 0xE1017000 + +/* + * Where's the flush address (for flushing D and I cache?) + */ +#define FLUSH_BASE 0xdf000000 +#define FLUSH_BASE_PHYS 0x00000000 + +#ifndef __ASSEMBLER__ + +#define PCIO_BASE 0 + +/* + * RAM definitions + */ +#define MAPTOPHYS(a) ((unsigned long)(a) - PAGE_OFFSET) +#define KERNTOPHYS(a) ((unsigned long)(&a)) +#define KERNEL_BASE (0x10008000) +#endif + +/* macro to get at IO space when running virtually */ +#define IO_ADDRESS(x) ((x)) + +/* ---------------------------------------------------------------------------- + * OMAP1510 system registers + * ---------------------------------------------------------------------------- + */ + +#define OMAP1510_UART1_BASE 0xfffb0000 /* "BLUETOOTH-UART" */ +#define OMAP1510_UART2_BASE 0xfffb0800 /* "MODEM-UART" */ +#define OMAP1510_RTC_BASE 0xfffb4800 /* RTC */ +#define OMAP1510_UART3_BASE 0xfffb9800 /* Shared MPU/DSP UART */ +#define OMAP1510_COM_MCBSP2_BASE 0xffff1000 /* Com McBSP2 */ +#define OMAP1510_AUDIO_MCBSP_BASE 0xffff1800 /* Audio McBSP2 */ +#define OMAP1510_ARMIO_BASE 0xfffb5000 /* keyboard/gpio */ + +/* + * OMAP1510 UART3 Registers + */ + +#define OMAP_MPU_UART3_BASE 0xFFFB9800 /* UART3 through MPU bus */ + +/* UART3 Registers Maping through MPU bus */ + +#define UART3_RHR (OMAP_MPU_UART3_BASE + 0) +#define UART3_THR (OMAP_MPU_UART3_BASE + 0) +#define UART3_DLL (OMAP_MPU_UART3_BASE + 0) +#define UART3_IER (OMAP_MPU_UART3_BASE + 4) +#define UART3_DLH (OMAP_MPU_UART3_BASE + 4) +#define UART3_IIR (OMAP_MPU_UART3_BASE + 8) +#define UART3_FCR (OMAP_MPU_UART3_BASE + 8) +#define UART3_EFR (OMAP_MPU_UART3_BASE + 8) +#define UART3_LCR (OMAP_MPU_UART3_BASE + 0x0C) +#define UART3_MCR (OMAP_MPU_UART3_BASE + 0x10) +#define UART3_XON1_ADDR1 (OMAP_MPU_UART3_BASE + 0x10) +#define UART3_XON2_ADDR2 (OMAP_MPU_UART3_BASE + 0x14) +#define UART3_LSR (OMAP_MPU_UART3_BASE + 0x14) +#define UART3_TCR (OMAP_MPU_UART3_BASE + 0x18) +#define UART3_MSR (OMAP_MPU_UART3_BASE + 0x18) +#define UART3_XOFF1 (OMAP_MPU_UART3_BASE + 0x18) +#define UART3_XOFF2 (OMAP_MPU_UART3_BASE + 0x1C) +#define UART3_SPR (OMAP_MPU_UART3_BASE + 0x1C) +#define UART3_TLR (OMAP_MPU_UART3_BASE + 0x1C) +#define UART3_MDR1 (OMAP_MPU_UART3_BASE + 0x20) +#define UART3_MDR2 (OMAP_MPU_UART3_BASE + 0x24) +#define UART3_SFLSR (OMAP_MPU_UART3_BASE + 0x28) +#define UART3_TXFLL (OMAP_MPU_UART3_BASE + 0x28) +#define UART3_RESUME (OMAP_MPU_UART3_BASE + 0x2C) +#define UART3_TXFLH (OMAP_MPU_UART3_BASE + 0x2C) +#define UART3_SFREGL (OMAP_MPU_UART3_BASE + 0x30) +#define UART3_RXFLL (OMAP_MPU_UART3_BASE + 0x30) +#define UART3_SFREGH (OMAP_MPU_UART3_BASE + 0x34) +#define UART3_RXFLH (OMAP_MPU_UART3_BASE + 0x34) +#define UART3_BLR (OMAP_MPU_UART3_BASE + 0x38) +#define UART3_ACREG (OMAP_MPU_UART3_BASE + 0x3C) +#define UART3_DIV16 (OMAP_MPU_UART3_BASE + 0x3C) +#define UART3_SCR (OMAP_MPU_UART3_BASE + 0x40) +#define UART3_SSR (OMAP_MPU_UART3_BASE + 0x44) +#define UART3_EBLR (OMAP_MPU_UART3_BASE + 0x48) +#define UART3_OSC_12M_SEL (OMAP_MPU_UART3_BASE + 0x4C) +#define UART3_MVR (OMAP_MPU_UART3_BASE + 0x50) + +/* + * Configuration Registers + */ +#define FUNC_MUX_CTRL_0 0xfffe1000 +#define FUNC_MUX_CTRL_1 0xfffe1004 +#define FUNC_MUX_CTRL_2 0xfffe1008 +#define COMP_MODE_CTRL_0 0xfffe100c +#define FUNC_MUX_CTRL_3 0xfffe1010 +#define FUNC_MUX_CTRL_4 0xfffe1014 +#define FUNC_MUX_CTRL_5 0xfffe1018 +#define FUNC_MUX_CTRL_6 0xfffe101C +#define FUNC_MUX_CTRL_7 0xfffe1020 +#define FUNC_MUX_CTRL_8 0xfffe1024 +#define FUNC_MUX_CTRL_9 0xfffe1028 +#define FUNC_MUX_CTRL_A 0xfffe102C +#define FUNC_MUX_CTRL_B 0xfffe1030 +#define FUNC_MUX_CTRL_C 0xfffe1034 +#define FUNC_MUX_CTRL_D 0xfffe1038 +#define PULL_DWN_CTRL_0 0xfffe1040 +#define PULL_DWN_CTRL_1 0xfffe1044 +#define PULL_DWN_CTRL_2 0xfffe1048 +#define PULL_DWN_CTRL_3 0xfffe104c +#define GATE_INH_CTRL_0 0xfffe1050 +#define VOLTAGE_CTRL_0 0xfffe1060 +#define TEST_DBG_CTRL_0 0xfffe1070 + +#define MOD_CONF_CTRL_0 0xfffe1080 + +/* + * Traffic Controller Memory Interface Registers + */ +#define TCMIF_BASE 0xfffecc00 +#define IMIF_PRIO (TCMIF_BASE + 0x00) +#define EMIFS_PRIO_REG (TCMIF_BASE + 0x04) +#define EMIFF_PRIO_REG (TCMIF_BASE + 0x08) +#define EMIFS_CONFIG_REG (TCMIF_BASE + 0x0c) +#define EMIFS_CS0_CONFIG (TCMIF_BASE + 0x10) +#define EMIFS_CS1_CONFIG (TCMIF_BASE + 0x14) +#define EMIFS_CS2_CONFIG (TCMIF_BASE + 0x18) +#define EMIFS_CS3_CONFIG (TCMIF_BASE + 0x1c) +#define EMIFF_SDRAM_CONFIG (TCMIF_BASE + 0x20) +#define EMIFF_MRS (TCMIF_BASE + 0x24) +#define TC_TIMEOUT1 (TCMIF_BASE + 0x28) +#define TC_TIMEOUT2 (TCMIF_BASE + 0x2c) +#define TC_TIMEOUT3 (TCMIF_BASE + 0x30) +#define TC_ENDIANISM (TCMIF_BASE + 0x34) +#define EMIFF_SDRAM_CONFIG_2 (TCMIF_BASE + 0x3c) +#define EMIF_CFG_DYNAMIC_WS (TCMIF_BASE + 0x40) + +/* + * LCD Panel + */ +#define TI925_LCD_BASE 0xFFFEC000 +#define TI925_LCD_CONTROL (TI925_LCD_BASE) +#define TI925_LCD_TIMING0 (TI925_LCD_BASE+0x4) +#define TI925_LCD_TIMING1 (TI925_LCD_BASE+0x8) +#define TI925_LCD_TIMING2 (TI925_LCD_BASE+0xc) +#define TI925_LCD_STATUS (TI925_LCD_BASE+0x10) +#define TI925_LCD_SUBPANEL (TI925_LCD_BASE+0x14) + +#define OMAP_LCD_CONTROL TI925_LCD_CONTROL + +/* + * MMC/SD Host Controller Registers + */ + +#define OMAP_MMC_CMD 0xFFFB7800 /* MMC Command */ +#define OMAP_MMC_ARGL 0xFFFB7804 /* MMC argument low */ +#define OMAP_MMC_ARGH 0xFFFB7808 /* MMC argument high */ +#define OMAP_MMC_CON 0xFFFB780C /* MMC system configuration */ +#define OMAP_MMC_STAT 0xFFFB7810 /* MMC status */ +#define OMAP_MMC_IE 0xFFFB7814 /* MMC system interrupt enable */ +#define OMAP_MMC_CTO 0xFFFB7818 /* MMC command time-out */ +#define OMAP_MMC_DTO 0xFFFB781C /* MMC data time-out */ +#define OMAP_MMC_DATA 0xFFFB7820 /* MMC TX/RX FIFO data */ +#define OMAP_MMC_BLEN 0xFFFB7824 /* MMC block length */ +#define OMAP_MMC_NBLK 0xFFFB7828 /* MMC number of blocks */ +#define OMAP_MMC_BUF 0xFFFB782C /* MMC buffer configuration */ +#define OMAP_MMC_SPI 0xFFFB7830 /* MMC serial port interface */ +#define OMAP_MMC_SDIO 0xFFFB7834 /* MMC SDIO mode configuration */ +#define OMAP_MMC_SYST 0xFFFB7838 /* MMC system test */ +#define OMAP_MMC_REV 0xFFFB783C /* MMC module version */ +#define OMAP_MMC_RSP0 0xFFFB7840 /* MMC command response 0 */ +#define OMAP_MMC_RSP1 0xFFFB7844 /* MMC command response 1 */ +#define OMAP_MMC_RSP2 0xFFFB7848 /* MMC command response 2 */ +#define OMAP_MMC_RSP3 0xFFFB784C /* MMC command response 3 */ +#define OMAP_MMC_RSP4 0xFFFB7850 /* MMC command response 4 */ +#define OMAP_MMC_RSP5 0xFFFB7854 /* MMC command response 5 */ +#define OMAP_MMC_RSP6 0xFFFB7858 /* MMC command response 6 */ +#define OMAP_MMC_RSP7 0xFFFB785C /* MMC command response 4 */ + +/* MMC masks */ + +#define OMAP_MMC_END_OF_CMD (1 << 0) /* End of command phase */ +#define OMAP_MMC_CARD_BUSY (1 << 2) /* Card enter busy state */ +#define OMAP_MMC_BLOCK_RS (1 << 3) /* Block received/sent */ +#define OMAP_MMC_EOF_BUSY (1 << 4) /* Card exit busy state */ +#define OMAP_MMC_DATA_TIMEOUT (1 << 5) /* Data response time-out */ +#define OMAP_MMC_DATA_CRC (1 << 6) /* Date CRC error */ +#define OMAP_MMC_CMD_TIMEOUT (1 << 7) /* Command response time-out */ +#define OMAP_MMC_CMD_CRC (1 << 8) /* Command CRC error */ +#define OMAP_MMC_A_FULL (1 << 10) /* Buffer almost full */ +#define OMAP_MMC_A_EMPTY (1 << 11) /* Buffer almost empty */ +#define OMAP_MMC_OCR_BUSY (1 << 12) /* OCR busy */ +#define OMAP_MMC_CARD_IRQ (1 << 13) /* Card IRQ received */ +#define OMAP_MMC_CARD_ERR (1 << 14) /* Card status error in response */ + +/* 2.9.2 MPUI Interface Registers FFFE:C900 */ + +#define MPUI_CTRL_REG (volatile __u32 *)(0xfffec900) +#define MPUI_DEBUG_ADDR (volatile __u32 *)(0xfffec904) +#define MPUI_DEBUG_DATA (volatile __u32 *)(0xfffec908) +#define MPUI_DEBUG_FLAG (volatile __u16 *)(0xfffec90c) +#define MPUI_STATUS_REG (volatile __u16 *)(0xfffec910) +#define MPUI_DSP_STATUS_REG (volatile __u16 *)(0xfffec914) +#define MPUI_DSP_BOOT_CONFIG (volatile __u16 *)(0xfffec918) +#define MPUI_DSP_API_CONFIG (volatile __u16 *)(0xfffec91c) + +/* 2.9.6 Traffic Controller Memory Interface Registers: */ +#define OMAP_IMIF_PRIO_REG 0xfffecc00 +#define OMAP_EMIFS_PRIO_REG 0xfffecc04 +#define OMAP_EMIFF_PRIO_REG 0xfffecc08 +#define OMAP_EMIFS_CONFIG_REG 0xfffecc0c +#define OMAP_EMIFS_CS0_CONFIG 0xfffecc10 +#define OMAP_EMIFS_CS1_CONFIG 0xfffecc14 +#define OMAP_EMIFS_CS2_CONFIG 0xfffecc18 +#define OMAP_EMIFS_CS3_CONFIG 0xfffecc1c +#define OMAP_EMIFF_SDRAM_CONFIG 0xfffecc20 +#define OMAP_EMIFF_MRS 0xfffecc24 +#define OMAP_TIMEOUT1 0xfffecc28 +#define OMAP_TIMEOUT2 0xfffecc2c +#define OMAP_TIMEOUT3 0xfffecc30 +#define OMAP_ENDIANISM 0xfffecc34 + +/* 2.9.10 EMIF Slow Interface Configuration Register (EMIFS_CONFIG_REG): */ +#define OMAP_EMIFS_CONFIG_FR (1 << 4) +#define OMAP_EMIFS_CONFIG_PDE (1 << 3) +#define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2) +#define OMAP_EMIFS_CONFIG_BM (1 << 1) +#define OMAP_EMIFS_CONFIG_WP (1 << 0) + +/* + * Memory chunk set aside for the Framebuffer in SRAM + */ +#define SRAM_FRAMEBUFFER_MEMORY OMAP1510_SRAM_BASE + + +/* + * DMA + */ + +#define OMAP1510_DMA_BASE 0xFFFED800 +#define OMAP_DMA_BASE OMAP1510_DMA_BASE + +/* Global Register selection */ +#define NO_GLOBAL_DMA_ACCESS 0 + +/* Channel select field + * NOTE: all other channels are linear, chan0 is 0, chan1 is 1, etc... + */ +#define LCD_CHANNEL 0xc + +/* Register Select Field (LCD) */ +#define DMA_LCD_CTRL 0 +#define DMA_LCD_TOP_F1_L 1 +#define DMA_LCD_TOP_F1_U 2 +#define DMA_LCD_BOT_F1_L 3 +#define DMA_LCD_BOT_F1_U 4 + +#define LCD_FRAME_MODE (1<<0) +#define LCD_FRAME_IT_IE (1<<1) +#define LCD_BUS_ERROR_IT_IE (1<<2) +#define LCD_FRAME_1_IT_COND (1<<3) +#define LCD_FRAME_2_IT_COND (1<<4) +#define LCD_BUS_ERROR_IT_COND (1<<5) +#define LCD_SOURCE_IMIF (1<<6) + +/* + * Real-Time Clock + */ + +#define RTC_SECONDS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x00) +#define RTC_MINUTES (volatile __u8 *)(OMAP1510_RTC_BASE + 0x04) +#define RTC_HOURS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x08) +#define RTC_DAYS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x0C) +#define RTC_MONTHS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x10) +#define RTC_YEARS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x14) +#define RTC_CTRL (volatile __u8 *)(OMAP1510_RTC_BASE + 0x40) + + +/* --------------------------------------------------------------------------- + * OMAP1510 Interrupt Handlers + * --------------------------------------------------------------------------- + * + */ +#define OMAP_IH1_BASE 0xfffecb00 +#define OMAP_IH2_BASE 0xfffe0000 +#define OMAP1510_ITR 0x0 +#define OMAP1510_MASK 0x4 + +#define INTERRUPT_HANDLER_BASE OMAP_IH1_BASE +#define INTERRUPT_INPUT_REGISTER OMAP1510_ITR +#define INTERRUPT_MASK_REGISTER OMAP1510_MASK + + +/* --------------------------------------------------------------------------- + * OMAP1510 TIMERS + * --------------------------------------------------------------------------- + * + */ + +#define OMAP1510_32kHz_TIMER_BASE 0xfffb9000 + +/* 32k Timer Registers */ +#define TIMER32k_CR 0x08 +#define TIMER32k_TVR 0x00 +#define TIMER32k_TCR 0x04 + +/* 32k Timer Control Register definition */ +#define TIMER32k_TSS (1<<0) +#define TIMER32k_TRB (1<<1) +#define TIMER32k_INT (1<<2) +#define TIMER32k_ARL (1<<3) + +/* MPU Timer base addresses */ +#define OMAP1510_MPUTIMER_BASE 0xfffec500 +#define OMAP1510_MPUTIMER_OFF 0x00000100 + +#define OMAP1510_TIMER1_BASE 0xfffec500 +#define OMAP1510_TIMER2_BASE 0xfffec600 +#define OMAP1510_TIMER3_BASE 0xfffec700 + +/* MPU Timer Registers */ +#define CNTL_TIMER 0 +#define LOAD_TIM 4 +#define READ_TIM 8 + +/* CNTL_TIMER register bits */ +#define MPUTIM_FREE (1<<6) +#define MPUTIM_CLOCK_ENABLE (1<<5) +#define MPUTIM_PTV_MASK (0x7<<PTV_BIT) +#define MPUTIM_PTV_BIT 2 +#define MPUTIM_AR (1<<1) +#define MPUTIM_ST (1<<0) + +/* --------------------------------------------------------------------------- + * OMAP1510 GPIO (SHARED) + * --------------------------------------------------------------------------- + * + */ +#define GPIO_DATA_INPUT_REG (OMAP1510_GPIO_BASE + 0x0) +#define GPIO_DATA_OUTPUT_REG (OMAP1510_GPIO_BASE + 0x4) +#define GPIO_DIR_CONTROL_REG (OMAP1510_GPIO_BASE + 0x8) +#define GPIO_INT_CONTROL_REG (OMAP1510_GPIO_BASE + 0xc) +#define GPIO_INT_MASK_REG (OMAP1510_GPIO_BASE + 0x10) +#define GPIO_INT_STATUS_REG (OMAP1510_GPIO_BASE + 0x14) +#define GPIO_PIN_CONTROL_REG (OMAP1510_GPIO_BASE + 0x18) + + +/* --------------------------- + * OMAP1510 MPUIO (ARM only) + *---------------------------- + */ +#define OMAP1510_MPUIO_BASE 0xFFFB5000 +#define MPUIO_DATA_INPUT_REG (OMAP1510_MPUIO_BASE + 0x0) +#define MPUIO_DATA_OUTPUT_REG (OMAP1510_MPUIO_BASE + 0x4) +#define MPUIO_DIR_CONTROL_REG (OMAP1510_MPUIO_BASE + 0x8) + +/* --------------------------------------------------------------------------- + * OMAP1510 TIPB (only) + * --------------------------------------------------------------------------- + * + */ +#define TIPB_PUBLIC_CNTL_BASE 0xfffed300 +#define MPU_PUBLIC_TIPB_CNTL_REG (TIPB_PUBLIC_CNTL_BASE + 0x8) +#define TIPB_PRIVATE_CNTL_BASE 0xfffeca00 +#define MPU_PRIVATE_TIPB_CNTL_REG (TIPB_PRIVATE_CNTL_BASE + 0x8) + +/* + * --------------------------------------------------------------------------- + * OMAP1510 Camera Interface + * --------------------------------------------------------------------------- + */ +#define CAMERA_BASE (IO_BASE + 0x6800) +#define CAM_CTRLCLOCK_REG (CAMERA_BASE + 0x00) +#define CAM_IT_STATUS_REG (CAMERA_BASE + 0x04) +#define CAM_MODE_REG (CAMERA_BASE + 0x08) +#define CAM_STATUS_REG (CAMERA_BASE + 0x0C) +#define CAM_CAMDATA_REG (CAMERA_BASE + 0x10) +#define CAM_GPIO_REG (CAMERA_BASE + 0x14) +#define CAM_PEAK_CTR_REG (CAMERA_BASE + 0x18) + +#if 0 +#ifndef __ASSEMBLY__ +typedef struct { + __u32 ctrlclock; + __u32 it_status; + __u32 mode; + __u32 status; + __u32 camdata; + __u32 gpio; + __u32 peak_counter; +} camera_regs_t; +#endif +#endif + +/* CTRLCLOCK bit shifts */ +#define FOSCMOD_BIT 0 +#define FOSCMOD_MASK (0x7 << FOSCMOD_BIT) +#define FOSCMOD_12MHz 0x0 +#define FOSCMOD_6MHz 0x2 +#define FOSCMOD_9_6MHz 0x4 +#define FOSCMOD_24MHz 0x5 +#define FOSCMOD_8MHz 0x6 +#define POLCLK (1<<3) +#define CAMEXCLK_EN (1<<4) +#define MCLK_EN (1<<5) +#define DPLL_EN (1<<6) +#define LCLK_EN (1<<7) + +/* IT_STATUS bit shifts */ +#define V_UP (1<<0) +#define V_DOWN (1<<1) +#define H_UP (1<<2) +#define H_DOWN (1<<3) +#define FIFO_FULL (1<<4) +#define DATA_XFER (1<<5) + +/* MODE bit shifts */ +#define CAMOSC (1<<0) +#define IMGSIZE_BIT 1 +#define IMGSIZE_MASK (0x3 << IMGSIZE_BIT) +#define IMGSIZE_CIF (0x0 << IMGSIZE_BIT) /* 352x288 */ +#define IMGSIZE_QCIF (0x1 << IMGSIZE_BIT) /* 176x144 */ +#define IMGSIZE_VGA (0x2 << IMGSIZE_BIT) /* 640x480 */ +#define IMGSIZE_QVGA (0x3 << IMGSIZE_BIT) /* 320x240 */ +#define ORDERCAMD (1<<3) +#define EN_V_UP (1<<4) +#define EN_V_DOWN (1<<5) +#define EN_H_UP (1<<6) +#define EN_H_DOWN (1<<7) +#define EN_DMA (1<<8) +#define THRESHOLD (1<<9) +#define THRESHOLD_BIT 9 +#define THRESHOLD_MASK (0x7f<<9) +#define EN_NIRQ (1<<16) +#define EN_FIFO_FULL (1<<17) +#define RAZ_FIFO (1<<18) + +/* STATUS bit shifts */ +#define VSTATUS (1<<0) +#define HSTATUS (1<<1) + +/* GPIO bit shifts */ +#define CAM_RST (1<<0) + + +/********************* + * Watchdog timer. + *********************/ +#define WDTIM_BASE 0xfffec800 +#define WDTIM_CONTROL (WDTIM_BASE+0x00) +#define WDTIM_LOAD (WDTIM_BASE+0x04) +#define WDTIM_READ (WDTIM_BASE+0x04) +#define WDTIM_MODE (WDTIM_BASE+0x08) + +/* Values to write to mode register to disable the watchdog function. */ +#define DISABLE_SEQ1 0xF5 +#define DISABLE_SEQ2 0xA0 + +/* WDTIM_CONTROL bit definitions. */ +#define WDTIM_CONTROL_ST BIT7 + + + +/* --------------------------------------------------------------------------- + * Differentiating processor versions for those who care. + * --------------------------------------------------------------------------- + * + */ +#define OMAP1509 0 +#define OMAP1510 1 + +#define OMAP1510_ID_CODE_REG 0xfffed404 + +#ifndef __ASSEMBLY__ +int cpu_type(void); +#endif + +/* + * EVM Implementation Specifics. + * + * *** NOTE *** + * Any definitions in these files should be prefixed by an identifier - + * eg. OMAP1510P1_FLASH0_BASE . + * + */ +#ifdef CONFIG_OMAP_INNOVATOR +#include "innovator.h" +#endif + +#ifdef CONFIG_OMAP_1510P1 +#include "omap1510p1.h" +#endif + +/*****************************************************************************/ + +#define CLKGEN_RESET_BASE (0xfffece00) +#define ARM_CKCTL (volatile __u16 *)(CLKGEN_RESET_BASE + 0x0) +#define ARM_IDLECT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x4) +#define ARM_IDLECT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x8) +#define ARM_EWUPCT (volatile __u16 *)(CLKGEN_RESET_BASE + 0xC) +#define ARM_RSTCT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x10) +#define ARM_RSTCT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x14) +#define ARM_SYSST (volatile __u16 *)(CLKGEN_RESET_BASE + 0x18) + + +#define CK_CLKIN 12 /* MHz */ +#define CK_RATEF 1 +#define CK_IDLEF 2 +#define CK_ENABLEF 4 +#define CK_SELECTF 8 +#ifndef __ASSEMBLER__ +#define CK_DPLL1 ((volatile __u16 *)0xfffecf00) +#else +#define CK_DPLL1 (0xfffecf00) +#endif +#define SETARM_IDLE_SHIFT + +/* ARM_CKCTL bit shifts */ +#define PERDIV 0 +#define LCDDIV 2 +#define ARMDIV 4 +#define DSPDIV 6 +#define TCDIV 8 +#define DSPMMUDIV 10 +#define ARM_TIMXO 12 +#define EN_DSPCK 13 +#define ARM_INTHCK_SEL 14 /* REVISIT -- where is this used? */ + +#define ARM_CKCTL_RSRVD_BIT15 (1 << 15) +#define ARM_CKCTL_ARM_INTHCK_SEL (1 << 14) +#define ARM_CKCTL_EN_DSPCK (1 << 13) +#define ARM_CKCTL_ARM_TIMXO (1 << 12) +#define ARM_CKCTL_DSPMMU_DIV1 (1 << 11) +#define ARM_CKCTL_DSPMMU_DIV2 (1 << 10) +#define ARM_CKCTL_TCDIV1 (1 << 9) +#define ARM_CKCTL_TCDIV2 (1 << 8) +#define ARM_CKCTL_DSPDIV1 (1 << 7) +#define ARM_CKCTL_DSPDIV0 (1 << 6) +#define ARM_CKCTL_ARMDIV1 (1 << 5) +#define ARM_CKCTL_ARMDIV0 (1 << 4) +#define ARM_CKCTL_LCDDIV1 (1 << 3) +#define ARM_CKCTL_LCDDIV0 (1 << 2) +#define ARM_CKCTL_PERDIV1 (1 << 1) +#define ARM_CKCTL_PERDIV0 (1 << 0) + +/* ARM_IDLECT1 bit shifts */ +#define IDLWDT_ARM 0 +#define IDLXORP_ARM 1 +#define IDLPER_ARM 2 +#define IDLLCD_ARM 3 +#define IDLLB_ARM 4 +#define IDLHSAB_ARM 5 +#define IDLIF_ARM 6 +#define IDLDPLL_ARM 7 +#define IDLAPI_ARM 8 +#define IDLTIM_ARM 9 +#define SETARM_IDLE 11 + +/* ARM_IDLECT2 bit shifts */ +#define EN_WDTCK 0 +#define EN_XORPCK 1 +#define EN_PERCK 2 +#define EN_LCDCK 3 +#define EN_LBCK 4 +#define EN_HSABCK 5 +#define EN_APICK 6 +#define EN_TIMCK 7 +#define DMACK_REQ 8 +#define EN_GPIOCK 9 +#define EN_LBFREECK 10 + +#define ARM_RSTCT1_SW_RST (1 << 3) +#define ARM_RSTCT1_DSP_RST (1 << 2) +#define ARM_RSTCT1_DSP_EN (1 << 1) +#define ARM_RSTCT1_ARM_RST (1 << 0) + +/* ARM_RSTCT2 bit shifts */ +#define EN_PER 0 + +#define ARM_SYSST_RSRVD_BIT15 (1 << 15) +#define ARM_SYSST_RSRVD_BIT14 (1 << 14) +#define ARM_SYSST_CLOCK_SELECT2 (1 << 13) +#define ARM_SYSST_CLOCK_SELECT1 (1 << 12) +#define ARM_SYSST_CLOCK_SELECT0 (1 << 11) +#define ARM_SYSST_RSRVD_BIT10 (1 << 10) +#define ARM_SYSST_RSRVD_BIT9 (1 << 9) +#define ARM_SYSST_RSRVD_BIT8 (1 << 8) +#define ARM_SYSST_RSRVD_BIT7 (1 << 7) +#define ARM_SYSST_IDLE_DSP (1 << 6) +#define ARM_SYSST_POR (1 << 5) +#define ARM_SYSST_EXT_RST (1 << 4) +#define ARM_SYSST_ARM_MCRST (1 << 3) +#define ARM_SYSST_ARM_WDRST (1 << 2) +#define ARM_SYSST_GLOB_SWRST (1 << 1) +#define ARM_SYSST_DSP_WDRST (1 << 0) + +/* Table 15-23. DPLL Control Registers: */ +#define DPLL_CTL_REG (volatile __u16 *)(0xfffecf00) + +/* Table 15-24. Control Register (CTL_REG): */ + +#define DPLL_CTL_REG_IOB (1 << 13) +#define DPLL_CTL_REG_PLL_MULT Fld(5,0) + +/*****************************************************************************/ + +/* OMAP INTERRUPT REGISTERS */ +#define IRQ_ITR 0x00 +#define IRQ_MIR 0x04 +#define IRQ_SIR_IRQ 0x10 +#define IRQ_SIR_FIQ 0x14 +#define IRQ_CONTROL_REG 0x18 +#define IRQ_ISR 0x9c +#define IRQ_ILR0 0x1c + +#define REG_IHL1_MIR (OMAP_IH1_BASE+IRQ_MIR) +#define REG_IHL2_MIR (OMAP_IH2_BASE+IRQ_MIR) + +/* INTERRUPT LEVEL REGISTER BITS */ +#define ILR_PRIORITY_MASK (0x3c) +#define ILR_PRIORITY_SHIFT (2) +#define ILR_LEVEL_TRIGGER (1<<1) +#define ILR_FIQ (1<<0) + +#define IRQ_LEVEL_INT 1 +#define IRQ_EDGE_INT 0 diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h new file mode 100644 index 0000000..66a8b6b --- /dev/null +++ b/include/configs/omap1510inn.h @@ -0,0 +1,170 @@ +/* + * (C) Copyright 2003 + * Texas Instruments. + * Kshitij Gupta <kshitij@ti.com> + * Configuation settings for the TI OMAP Innovator board. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ +#define CONFIG_ARM925T 1 /* This is an arm925t CPU */ +#define CONFIG_OMAP 1 /* in a TI OMAP core */ +#define CONFIG_OMAP1510 1 /* which is in a 1510 (helen) */ +#define CONFIG_INNOVATOROMAP1510 1 /* a Innovator Board */ + +/* input clock of PLL */ +#define CONFIG_SYS_CLK_FREQ 12000000 /* the OMAP1510 Innovator has 12MHz input clock */ + +#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */ + +#define CONFIG_MISC_INIT_R + +#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ +#define CONFIG_SETUP_MEMORY_TAGS 1 + +/* + * Size of malloc() pool + */ +#define CFG_MALLOC_LEN (CFG_ENV_SIZE + 128*1024) + +/* + * Hardware drivers + */ +/* +#define CONFIG_DRIVER_SMC9196 +#define CONFIG_SMC9196_BASE 0x08000300 +#define CONFIG_SMC9196_EXT_PHY +*/ +#define CONFIG_DRIVER_LAN91C96 +#define CONFIG_LAN91C96_BASE 0x08000300 +#define CONFIG_LAN91C96_EXT_PHY + +/* + * NS16550 Configuration + */ +#define CFG_NS16550 +#define CFG_NS16550_SERIAL +#define CFG_NS16550_REG_SIZE (-4) +#define CFG_NS16550_CLK (CONFIG_SYS_CLK_FREQ) /* can be 12M/32Khz or 48Mhz */ +#define CFG_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart on helen */ + +/* + * select serial console configuration + */ +#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP1510 Innovator */ + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP) +#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> +#include <configs/omap1510.h> + +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd root=/dev/nfs rw nfsroot=157.87.82.48:/home/a0875451/mwd/myfs/target ip=dhcp" +/*#define CONFIG_ETHADDR 00:0B:36:00:05:25 */ +#define CONFIG_NETMASK 255.255.254.0 /* talk on MY local net */ +#define CONFIG_IPADDR 156.117.97.156 /* static IP I currently own */ +#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */ +#define CONFIG_BOOTFILE "/tftpboot/uImage" /* file to load */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ +/* what's this ? it's not used anywhere */ +#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ +#endif + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "OMAP1510 Innovator # " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x10000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ + +#undef CFG_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CFG_LOAD_ADDR 0x10000000 /* default load address */ + +/* The 1510 has 3 timers, they can be driven by the RefClk (12Mhz) or by DPLL1. + * This time is further subdivided by a local divisor. + */ +#define CFG_TIMERBASE 0xFFFEC500 /* use timer 1 */ +#define CFG_PVT 7 /* 2^(pvt+1), divide by 256 */ +#define CFG_HZ ((CONFIG_SYS_CLK_FREQ)/(2 << CFG_PVT)) + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ +#ifdef CONFIG_USE_IRQ +#define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */ +#define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */ +#endif + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ +#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ + +#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ + +#define CFG_FLASH_BASE PHYS_FLASH_1 + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define PHYS_FLASH_SIZE 0x01000000 /* 16MB */ +#define CFG_MAX_FLASH_SECT (128) /* max number of sectors on one chip */ +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x020000) /* addr of environment */ + +/* timeout values are in ticks */ +#define CFG_FLASH_ERASE_TOUT (20*CFG_HZ) /* Timeout for Flash Erase */ +#define CFG_FLASH_WRITE_TOUT (20*CFG_HZ) /* Timeout for Flash Write */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ +#define CFG_ENV_OFFSET 0x20000 /* environment starts here */ + +#endif /* __CONFIG_H */ |