summaryrefslogtreecommitdiff
path: root/include/configs
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs')
-rw-r--r--include/configs/MPC8540ADS.h44
-rw-r--r--include/configs/MPC8540EVAL.h8
-rw-r--r--include/configs/MPC8541CDS.h48
-rw-r--r--include/configs/MPC8548CDS.h54
-rw-r--r--include/configs/MPC8555CDS.h50
-rw-r--r--include/configs/MPC8560ADS.h20
-rw-r--r--include/configs/MPC8641HPCN.h634
-rw-r--r--include/configs/PM854.h8
-rw-r--r--include/configs/PM856.h8
-rw-r--r--include/configs/SBC8540.h8
-rw-r--r--include/configs/TQM85xx.h7
-rw-r--r--include/configs/sbc8560.h8
-rw-r--r--include/configs/stxgp3.h8
13 files changed, 828 insertions, 77 deletions
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 131c832..74a84f4 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -68,6 +68,10 @@
* The board, however, can run at 66MHz. In any event, this value
* must match the settings of some switches. Details can be found
* in the README.mpc85xxads.
+ *
+ * XXX -- Can't we run at 66 MHz, anyway? PCI should drop to
+ * 33MHz to accommodate, based on a PCI pin.
+ * Note that PCI-X won't work at 33MHz.
*/
#ifndef CONFIG_SYS_CLK_FREQ
@@ -293,12 +297,31 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8540@0"
+#define OF_SOC "soc8540@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8540@e0000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* RapidIO MMU */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
@@ -312,9 +335,10 @@
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+#define CFG_PCI1_IO_BASE 0x0
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
#if defined(CONFIG_PCI)
@@ -497,8 +521,10 @@
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
@@ -506,13 +532,15 @@
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr $ramdiskaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index 1af9231..418a3a3 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -179,12 +179,16 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* General PCI */
#define CFG_PCI_MEM_BASE 0x80000000
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index c96b98b..db389cf 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -308,13 +308,29 @@ extern unsigned long get_clock_freq(void);
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8541@0"
+#define OF_SOC "soc8541@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8541@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
@@ -323,32 +339,27 @@ extern unsigned long get_clock_freq(void);
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe2100000
+#define CFG_PCI2_IO_SIZE 0x100000 /* 1M */
#if defined(CONFIG_PCI)
+#define CONFIG_MPC85XX_PCI2
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
-#endif
-
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
@@ -482,8 +493,10 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
@@ -491,7 +504,8 @@ extern unsigned long get_clock_freq(void);
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 4ca8bc3..be8f93f 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -314,13 +314,29 @@ extern unsigned long get_clock_freq(void);
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8548@0"
+#define OF_SOC "soc8548@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8548@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
@@ -329,32 +345,27 @@ extern unsigned long get_clock_freq(void);
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe2100000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_85XX_PCI2
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
-#endif
-
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
@@ -382,13 +393,11 @@ extern unsigned long get_clock_freq(void);
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
#define TSEC4_PHY_ADDR 3
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
-#define FEC_PHYIDX 0
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
@@ -476,6 +485,8 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.253
@@ -498,8 +509,11 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
+
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
@@ -507,7 +521,9 @@ extern unsigned long get_clock_freq(void);
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index a44e3ec..4c8b4e7 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -308,13 +308,29 @@ extern unsigned long get_clock_freq(void);
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8555@0"
+#define OF_SOC "soc8555@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
@@ -323,33 +339,28 @@ extern unsigned long get_clock_freq(void);
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe2100000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_MPC85XX_PCI2
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
-#endif
-
-#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
@@ -482,8 +493,10 @@ extern unsigned long get_clock_freq(void);
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
@@ -491,7 +504,8 @@ extern unsigned long get_clock_freq(void);
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 2d5031b..835bf5c 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -290,12 +290,28 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/* pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8560@0"
+#define OF_SOC "soc8560@e0000000"
+#define OF_TBCLK (bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH "/soc8560@e0000000/serial@4500"
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* RapidIO MMU */
#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
new file mode 100644
index 0000000..246ac7f
--- /dev/null
+++ b/include/configs/MPC8641HPCN.h
@@ -0,0 +1,634 @@
+/*
+ * Copyright 2006 Freescale Semiconductor.
+ *
+ * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * MPC8641HPCN board configuration file
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_MPC86xx 1 /* MPC86xx */
+#define CONFIG_MPC8641 1 /* MPC8641 specific */
+#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
+#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
+#undef DEBUG
+
+#ifdef RUN_DIAG
+#define CFG_DIAG_ADDR 0xff800000
+#endif
+
+#define CFG_RESET_ADDRESS 0xfff00100
+
+/*#undef CONFIG_PCI*/
+#define CONFIG_PCI
+
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+/* #define CONFIG_DDR_INTERLEAVE 1 */
+#define CACHE_LINE_INTERLEAVING 0x20000000
+#define PAGE_INTERLEAVING 0x21000000
+#define BANK_INTERLEAVING 0x22000000
+#define SUPER_BANK_INTERLEAVING 0x23000000
+
+
+#define CONFIG_ALTIVEC 1
+
+/*
+ * L2CR setup -- make sure this is right for your board!
+ */
+#define CFG_L2
+#define L2_INIT 0
+#define L2_ENABLE (L2CR_L2E)
+
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define MPC86xx_DDR_SDRAM_CLK_CNTL
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS2 0x52 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS3 0x53 /* DDR DIMM */
+ #define SPD_EEPROM_ADDRESS4 0x54 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR1 parameters
+ */
+
+ #define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
+
+ #define CFG_DDR_CS0_BNDS 0x0000000F
+ #define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
+ #define CFG_DDR_EXT_REFRESH 0x00000000
+ #define CFG_DDR_TIMING_0 0x00260802
+ #define CFG_DDR_TIMING_1 0x39357322
+ #define CFG_DDR_TIMING_2 0x14904cc8
+ #define CFG_DDR_MODE_1 0x00480432
+ #define CFG_DDR_MODE_2 0x00000000
+ #define CFG_DDR_INTERVAL 0x06090100
+ #define CFG_DDR_DATA_INIT 0xdeadbeef
+ #define CFG_DDR_CLK_CTRL 0x03800000
+ #define CFG_DDR_OCD_CTRL 0x00000000
+ #define CFG_DDR_OCD_STATUS 0x00000000
+ #define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
+ #define CFG_DDR_CONTROL2 0x04400000
+
+ /* Not used in fixed_sdram function */
+
+ #define CFG_DDR_MODE 0x00000022
+ #define CFG_DDR_CS1_BNDS 0x00000000
+ #define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
+ #define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
+#endif
+
+#define CFG_ID_EEPROM 1
+#define ID_EEPROM_ADDR 0x57
+
+/*
+ * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
+ * There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
+ * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
+ * However, when u-boot comes up, the flash_init needs hard start addresses
+ * to build its info table. For user convenience, the flash addresses is
+ * fe800000 and ff800000. That way, u-boot knows where the flash is
+ * and the user can download u-boot code from promjet to fef00000, a
+ * more intuitive location than fe700000.
+ *
+ * Note that, on switching the boot location, fef00000 becomes fff00000.
+ */
+#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
+#define CFG_FLASH_BASE2 0xff800000
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+
+#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/
+
+#define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */
+#define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/
+
+#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
+#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
+
+#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
+#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+
+
+#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_ID 0x0 /* Board ID at offset 0 */
+#define PIXIS_VER 0x1 /* Board version at offset 1 */
+#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
+#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
+#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */
+#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
+#define PIXIS_VCTL 0x10 /* VELA Control Register */
+#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
+#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
+#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
+#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
+#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
+#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+
+#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+#define CFG_RAMBOOT
+#else
+#undef CFG_RAMBOOT
+#endif
+
+#if defined(CFG_RAMBOOT)
+#undef CFG_FLASH_CFI_DRIVER
+#undef CONFIG_SPD_EEPROM
+#define CFG_SDRAM_SIZE 256
+#endif
+
+#undef CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#ifndef CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
+#else
+#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
+#endif
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_CLK get_bus_freq(0)
+
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
+
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+
+/* Use the HUSH parser */
+#define CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
+
+/*
+ * Pass open firmware flat tree to kernel
+ */
+#define CONFIG_OF_FLAT_TREE 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE 8192
+
+#define OF_CPU "PowerPC,8641@0"
+#define OF_SOC "soc8641@f8000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8641@f8000000/serial@4500"
+
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3100
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0xe2000000
+#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
+#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
+/* For RTL8139 */
+#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
+#define _IO_BASE 0x00000000
+
+#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI2_IO_BASE 0xe3000000
+#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
+#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+
+#if defined(CONFIG_PCI)
+
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#undef CFG_SCSI_SCAN_BUS_REVERSE
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+
+#define CONFIG_RTL8139
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+#endif
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SCSI_AHCI
+
+#ifdef CONFIG_SCSI_AHCI
+#define CONFIG_SATA_ULI5288
+#define CFG_SCSI_MAX_SCSI_ID 4
+#define CFG_SCSI_MAX_LUN 1
+#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
+#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#endif
+
+#endif /* CONFIG_PCI */
+
+#if defined(CONFIG_TSEC_ENET)
+
+#ifndef CONFIG_NET_MULTI
+#define CONFIG_NET_MULTI 1
+#endif
+
+#define CONFIG_MII 1 /* MII PHY management */
+
+#define CONFIG_MPC86XX_TSEC1 1
+#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
+#define CONFIG_MPC86XX_TSEC2 1
+#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
+#define CONFIG_MPC86XX_TSEC3 1
+#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
+#define CONFIG_MPC86XX_TSEC4 1
+#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
+
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC3_PHY_ADDR 2
+#define TSEC4_PHY_ADDR 3
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC3_PHYIDX 0
+#define TSEC4_PHYIDX 0
+
+#define CONFIG_ETHPRIME "eTSEC1"
+
+#endif /* CONFIG_TSEC_ENET */
+
+/*
+ * BAT0 2G Cacheable, non-guarded
+ * 0x0000_0000 2G DDR
+ */
+#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
+#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
+#define CFG_IBAT0U CFG_DBAT0U
+
+/*
+ * BAT1 1G Cache-inhibited, guarded
+ * 0x8000_0000 512M PCI-Express 1 Memory
+ * 0xa000_0000 512M PCI-Express 2 Memory
+ * Changed it for operating from 0xd0000000
+ */
+#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT1U CFG_DBAT1U
+
+/*
+ * BAT2 512M Cache-inhibited, guarded
+ * 0xc000_0000 512M RapidIO Memory
+ */
+#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U CFG_DBAT2U
+
+/*
+ * BAT3 4M Cache-inhibited, guarded
+ * 0xf800_0000 4M CCSR
+ */
+#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U CFG_DBAT3U
+
+/*
+ * BAT4 32M Cache-inhibited, guarded
+ * 0xe200_0000 16M PCI-Express 1 I/O
+ * 0xe300_0000 16M PCI-Express 2 I/0
+ * Note that this is at 0xe0000000
+ */
+#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_IBAT4U CFG_DBAT4U
+
+/*
+ * BAT5 128K Cacheable, non-guarded
+ * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ */
+#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CFG_IBAT5L CFG_DBAT5L
+#define CFG_IBAT5U CFG_DBAT5U
+
+/*
+ * BAT6 32M Cache-inhibited, guarded
+ * 0xfe00_0000 32M FLASH
+ */
+#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CFG_IBAT6U CFG_DBAT6U
+
+#define CFG_DBAT7L 0x00000000
+#define CFG_DBAT7U 0x00000000
+#define CFG_IBAT7L 0x00000000
+#define CFG_IBAT7U 0x00000000
+
+/*
+ * Environment
+ */
+#ifndef CFG_RAMBOOT
+ #define CFG_ENV_IS_IN_FLASH 1
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SIZE 0x2000
+#else
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
+#endif
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#if defined(CFG_RAMBOOT)
+ #if defined(CONFIG_PCI)
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_PCI \
+ | CFG_CMD_I2C \
+ | CFG_CMD_SCSI \
+ | CFG_CMD_EXT2) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_IMLS \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_LOADS))
+ #else
+ #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_SCSI \
+ | CGF_CMD_EXT2) \
+ & \
+ ~(CFG_CMD_ENV \
+ | CFG_CMD_IMLS \
+ | CFG_CMD_FLASH \
+ | CFG_CMD_LOADS))
+ #endif
+#else
+ #if defined(CONFIG_PCI)
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PCI \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C \
+ | CFG_CMD_SCSI \
+ | CFG_CMD_EXT2)
+ #else
+ #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+ | CFG_CMD_PING \
+ | CFG_CMD_I2C)
+ #endif
+#endif
+
+#include <cmd_confdefs.h>
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_LOAD_ADDR 0x2000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* Cache Configuration */
+#define CFG_DCACHE_SIZE 32768
+#define CFG_CACHELINE_SIZE 32
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
+#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_ETHADDR 00:E0:0C:00:00:01
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
+#endif
+
+#define CONFIG_HAS_ETH1 1
+#define CONFIG_HAS_ETH2 1
+#define CONFIG_HAS_ETH3 1
+
+#define CONFIG_IPADDR 192.168.1.100
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /opt/nfsroot
+#define CONFIG_BOOTFILE uImage
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR 1000000
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "dtbaddr=400000\0" \
+ "dtbfile=mpc8641_hpcn.dtb\0" \
+ "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
+ "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "maxcpus=2"
+
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr - $dtbaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $dtbaddr $dtbfile;" \
+ "bootm $loadaddr $ramdiskaddr $dtbaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
+
+#endif /* __CONFIG_H */
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index da01186..4fb5440 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -193,12 +193,16 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* EEPROM configuration
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index 4d83487..87ab934 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -190,12 +190,16 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* EEPROM configuration
diff --git a/include/configs/SBC8540.h b/include/configs/SBC8540.h
index 0451b20..f8e3397 100644
--- a/include/configs/SBC8540.h
+++ b/include/configs/SBC8540.h
@@ -214,12 +214,16 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
#define CFG_PCI_MEM_BASE 0xC0000000
#define CFG_PCI_MEM_PHYS 0xC0000000
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index bc3b9aa..cce4624 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -192,12 +192,17 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x48} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/* I2C RTC */
#define CONFIG_RTC_DS1337 /* Use ds1337 rtc via i2c */
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 5a434dc..6e4fdb2 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -197,12 +197,16 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
#define CFG_PCI_MEM_BASE 0xC0000000
#define CFG_PCI_MEM_PHYS 0xC0000000
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index e218597..625cf20 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -172,8 +172,11 @@
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
@@ -183,6 +186,7 @@
/* I did the 'if 0' so we could keep the syntax above if ever needed. */
#undef CFG_I2C_NOPROBES
#endif
+#define CFG_I2C_OFFSET 0x3000
/* RapdIO Map configuration, mapped 1:1.
*/
generated by cgit v1.1 at 2024-11-16 13:59:20 +0000