diff options
Diffstat (limited to 'include/configs')
| -rw-r--r-- | include/configs/IceCube.h | 2 | ||||
| -rw-r--r-- | include/configs/MPC8260ADS.h | 99 | ||||
| -rw-r--r-- | include/configs/NETPHONE.h | 694 | ||||
| -rw-r--r-- | include/configs/NETTA.h | 745 | ||||
| -rw-r--r-- | include/configs/NETVIA.h | 35 |
5 files changed, 1524 insertions, 51 deletions
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h index b0e9e44..ce6e591 100644 --- a/include/configs/IceCube.h +++ b/include/configs/IceCube.h @@ -232,7 +232,7 @@ * Ethernet configuration */ #define CONFIG_MPC5xxx_FEC 1 -/* +/* * Define CONFIG_FEC_10MBIT to force FEC at 10Mb */ /* #define CONFIG_FEC_10MBIT 1 */ diff --git a/include/configs/MPC8260ADS.h b/include/configs/MPC8260ADS.h index efc7a61..7bd0d8e 100644 --- a/include/configs/MPC8260ADS.h +++ b/include/configs/MPC8260ADS.h @@ -7,10 +7,11 @@ * Note: my board is a PILOT rev. * Note: the mpc8260ads doesn't come with a proper Ethernet MAC address. * - * (C) Copyright 2003 Arabella Software Ltd. + * (C) Copyright 2003-2004 Arabella Software Ltd. * Yuli Barcohen <yuli@arabellasw.com> * Added support for SDRAM DIMMs SPD EEPROM, MII, JFFS2. * Ported to PQ2FADS-ZU and PQ2FADS-VR boards. + * Ported to MPC8272ADS board. * * See file CREDITS for list of people who contributed to this * project. @@ -39,18 +40,24 @@ * (easy to change) */ -#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */ -#define CONFIG_MPC8260ADS 1 /* ...on motorola ads board */ +#define CONFIG_MPC8260ADS 1 /* Motorola PQ2 ADS family board */ /* ADS flavours */ #define CFG_8260ADS 1 /* MPC8260ADS */ #define CFG_8266ADS 2 /* MPC8266ADS */ #define CFG_PQ2FADS 3 /* PQ2FADS-ZU or PQ2FADS-VR */ +#define CFG_8272ADS 4 /* MPC8272ADS */ #ifndef CONFIG_ADSTYPE #define CONFIG_ADSTYPE CFG_8260ADS #endif /* CONFIG_ADSTYPE */ +#if CONFIG_ADSTYPE == CFG_8272ADS +#define CONFIG_MPC8272 1 +#else +#define CONFIG_MPC8260 1 +#endif /* CONFIG_ADSTYPE == CFG_8272ADS */ + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ /* allow serial and ethaddr to be overwritten */ @@ -92,42 +99,60 @@ #define CONFIG_ETHER_INDEX 2 /* which SCC/FCC channel for ethernet */ -#if (CONFIG_ETHER_INDEX == 2) -/* - * - Rx-CLK is CLK13 - * - Tx-CLK is CLK14 - * - Select bus for bd/buffers (see 28-13) - * - Full duplex - */ -# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) +#if CONFIG_ETHER_INDEX == 1 + +# define CFG_PHY_ADDR 0 +# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK10) +# define CFG_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) + +#elif CONFIG_ETHER_INDEX == 2 + +#if CONFIG_ADSTYPE == CFG_8272ADS /* RxCLK is CLK15, TxCLK is CLK16 */ +# define CFG_PHY_ADDR 3 +# define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK15 | CMXFCR_TF2CS_CLK16) +#else /* RxCLK is CLK13, TxCLK is CLK14 */ +# define CFG_PHY_ADDR 0 # define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) -# define CFG_CPMFCR_RAMTYPE 0 -# define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) +#endif /* CONFIG_ADSTYPE == CFG_8272ADS */ + +# define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) #endif /* CONFIG_ETHER_INDEX */ +#define CFG_CPMFCR_RAMTYPE 0 /* BDs and buffers on 60x bus */ +#define CFG_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) /* Full duplex */ + #define CONFIG_MII /* MII PHY management */ #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ /* * GPIO pins used for bit-banged MII communications */ #define MDIO_PORT 2 /* Port C */ -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 +#if CONFIG_ADSTYPE == CFG_8272ADS +#define CFG_MDIO_PIN 0x00002000 /* PC18 */ +#define CFG_MDC_PIN 0x00001000 /* PC19 */ +#else +#define CFG_MDIO_PIN 0x00400000 /* PC9 */ +#define CFG_MDC_PIN 0x00200000 /* PC10 */ +#endif /* CONFIG_ADSTYPE == CFG_8272ADS */ + +#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN) +#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN) +#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) + +#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \ + else iop->pdat &= ~CFG_MDIO_PIN -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 +#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \ + else iop->pdat &= ~CFG_MDC_PIN #define MIIDELAY udelay(1) #endif /* CONFIG_ETHER_ON_FCC */ -#if CONFIG_ADSTYPE == CFG_PQ2FADS -#undef CONFIG_SPD_EEPROM /* On PQ2FADS-ZU, SDRAM is soldered */ +#if CONFIG_ADSTYPE >= CFG_PQ2FADS +#undef CONFIG_SPD_EEPROM /* On new boards, SDRAM is soldered */ #else #define CONFIG_HARD_I2C 1 /* To enable I2C support */ #define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ @@ -136,21 +161,21 @@ #if defined(CONFIG_SPD_EEPROM) && !defined(CONFIG_SPD_ADDR) #define CONFIG_SPD_ADDR 0x50 #endif -#endif /* CONFIG_ADSTYPE == CFG_PQ2FADS */ +#endif /* CONFIG_ADSTYPE >= CFG_PQ2FADS */ #ifndef CONFIG_SDRAM_PBI #define CONFIG_SDRAM_PBI 0 /* By default, use bank-based interleaving */ #endif #ifndef CONFIG_8260_CLKIN -#if CONFIG_ADSTYPE == CFG_PQ2FADS +#if CONFIG_ADSTYPE >= CFG_PQ2FADS #define CONFIG_8260_CLKIN 100000000 /* in Hz */ #else #define CONFIG_8260_CLKIN 66000000 /* in Hz */ #endif #endif -#define CONFIG_BAUDRATE 115200 +#define CONFIG_BAUDRATE 38400 #define CFG_EXCLUDE CFG_CMD_BEDBUG | \ CFG_CMD_BMP | \ @@ -176,7 +201,7 @@ CFG_CMD_USB | \ CFG_CMD_VFD -#if CONFIG_ADSTYPE == CFG_PQ2FADS +#if CONFIG_ADSTYPE >= CFG_PQ2FADS #define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \ CFG_CMD_SDRAM | \ CFG_CMD_I2C | \ @@ -184,14 +209,14 @@ #else #define CONFIG_COMMANDS (CFG_CMD_ALL & ~( \ CFG_EXCLUDE ) ) -#endif /* CONFIG_ADSTYPE == CFG_PQ2FADS */ +#endif /* CONFIG_ADSTYPE >= CFG_PQ2FADS */ /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "bootm 100000" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/ram rw" +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#define CONFIG_BOOTCOMMAND "bootm fff80000" /* autoboot command */ +#define CONFIG_BOOTARGS "root=/dev/mtdblock2" #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ @@ -256,12 +281,12 @@ #define RS232EN_2 0x01000001 #define FETHIEN1 0x08000008 #define FETH1_RST 0x04000004 -#define FETHIEN2 0x01000000 +#define FETHIEN2 0x10000000 #define FETH2_RST 0x08000000 #define BCSR_PCI_MODE 0x01000000 #define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ #define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET @@ -273,7 +298,6 @@ ( HRCW_BMS | HRCW_APPC10 ) |\ ( HRCW_MODCK_H0101 ) \ ) - /* no slaves */ #define CFG_HRCW_SLAVE1 0 #define CFG_HRCW_SLAVE2 0 @@ -336,8 +360,8 @@ #define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) #define CFG_RCCR 0 -#if CONFIG_ADSTYPE == CFG_8266ADS -#undef CFG_LSDRAM_BASE /* No local bus SDRAM on MPC8266ADS */ +#if (CONFIG_ADSTYPE == CFG_8266ADS) || (CONFIG_ADSTYPE == CFG_8272ADS) +#undef CFG_LSDRAM_BASE /* No local bus SDRAM on these boards */ #endif /* CONFIG_ADSTYPE == CFG_8266ADS */ #if CONFIG_ADSTYPE == CFG_PQ2FADS @@ -347,6 +371,11 @@ #define CFG_LSDMR 0x828737A3 #define CFG_LSRT 0x13 #define CFG_MPTPR 0x2800 +#elif CONFIG_ADSTYPE == CFG_8272ADS +#define CFG_OR2 0xFC002CC0 +#define CFG_PSDMR 0x834E24A3 +#define CFG_PSRT 0x13 +#define CFG_MPTPR 0x2800 #else #define CFG_OR2 0xFF000CA0 #define CFG_PSDMR 0x016EB452 diff --git a/include/configs/NETPHONE.h b/include/configs/NETPHONE.h new file mode 100644 index 0000000..6dd12fe --- /dev/null +++ b/include/configs/NETPHONE.h @@ -0,0 +1,694 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Pantelis Antoniou, Intracom S.A., panto@intracom.gr + * U-Boot port on NetTA4 board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC870 1 /* This is a MPC885 CPU */ +#define CONFIG_NETPHONE 1 /* ...on a NetPhone board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +/* #define CONFIG_XIN 10000000 */ +#define CONFIG_XIN 50000000 +#define MPC8XX_HZ 120000000 + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_AUTOSCRIPT +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_STATUS_LED 1 /* Status LED enabled */ +#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE | CONFIG_BOOTP_NISDOMAIN) + +#undef CONFIG_MAC_PARTITION +#undef CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */ +#define FEC_ENET 1 /* eth.c needs it that way... */ +#undef CFG_DISCOVER_PHY +#define CONFIG_MII 1 +#define CONFIG_RMII 1 /* use RMII interface */ + +#define CONFIG_ETHER_ON_FEC1 1 +#define CONFIG_FEC1_PHY 8 /* phy address of FEC */ +#define CONFIG_FEC1_PHY_NORXERR 1 + +#define CONFIG_ETHER_ON_FEC2 1 +#define CONFIG_FEC2_PHY 4 +#define CONFIG_FEC2_PHY_NORXERR 1 + +#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_DHCP | \ + CFG_CMD_PING | \ + CFG_CMD_MII | \ + CFG_CMD_CDP \ + ) + +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_MISC_INIT_R + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0300000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SECT_SIZE 0x10000 + +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000) +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 0x4000 + +#define CFG_ENV_ADDR_REDUND (CFG_FLASH_BASE + 0x70000) +#define CFG_ENV_OFFSET_REDUND 0 +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + */ + +#if CONFIG_XIN == 10000000 + +#if MPC8XX_HZ == 120000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 50000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 25000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 40000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 75000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 10MHz +#endif + +#elif CONFIG_XIN == 50000000 + +#if MPC8XX_HZ == 120000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 50MHz +#endif + +#else + +#error unsupported XIN freq +#endif + + +/* + *----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ + +#define SCCR_MASK SCCR_EBDF11 +#if MPC8XX_HZ > 66666666 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00 | SCCR_EBDF01) +#else +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) +#endif + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR3 and OR3 (SDRAM) + * + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) + +#define CFG_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CFG_OR_TIMING_SDRAM) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V) + +/* + * Memory Periodic Timer Prescaler + */ + +/* + * Memory Periodic Timer Prescaler + * + * The Divider for PTA (refresh timer) configuration is based on an + * example SDRAM configuration (64 MBit, one bank). The adjustment to + * the number of chip selects (NCS) and the actually needed refresh + * rate is done by setting MPTPR. + * + * PTA is calculated from + * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) + * + * gclk CPU clock (not bus clock!) + * Trefresh Refresh cycle * 4 (four word bursts used) + * + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ + +#define CFG_MAMR_PTA 234 + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_ARTOS /* include ARTOS support */ + +#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */ + +/****************************************************************/ + +#define DSP_SIZE 0x00010000 /* 64K */ +#define NAND_SIZE 0x00010000 /* 64K */ +#define ER_SIZE 0x00010000 /* 64K */ + +#define DSP_BASE 0xF1000000 +#define NAND_BASE 0xF1010000 +#define ER_BASE 0xF1020000 + +/****************************************************************/ + +/* NAND */ +#define CFG_NAND_BASE NAND_BASE +#define CONFIG_MTD_NAND_ECC_JFFS2 + +#define CFG_MAX_NAND_DEVICE 1 + +#define SECTORSIZE 512 +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +/* ALE = PD17, CLE = PE18, CE = PE20, F_RY_BY = PE31 */ +#define NAND_DISABLE_CE(nand) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) |= (1 << (31 - 20)); \ + } while(0) + +#define NAND_ENABLE_CE(nand) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 20)); \ + } while(0) + +#define NAND_CTL_CLRALE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 17)); \ + } while(0) + +#define NAND_CTL_SETALE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) |= (1 << (31 - 17)); \ + } while(0) + +#define NAND_CTL_CLRCLE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) &= ~(1 << (31 - 18)); \ + } while(0) + +#define NAND_CTL_SETCLE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat) |= (1 << (31 - 18)); \ + } while(0) + +#define NAND_WAIT_READY(nand) \ + do { \ + while ((((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat & (1 << (31 - 31))) == 0) \ + ; \ + } while (0) + +#define WRITE_NAND_COMMAND(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define WRITE_NAND_ADDRESS(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define WRITE_NAND(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define READ_NAND(adr) \ + ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr))) + +/*****************************************************************************/ + +#define STATUS_LED_BIT 0x00000008 /* bit 28 */ +#define STATUS_LED_PERIOD (CFG_HZ / 2) +#define STATUS_LED_STATE STATUS_LED_BLINKING + +#define STATUS_LED_ACTIVE 0 /* LED on for bit == 0 */ +#define STATUS_LED_BOOT 0 /* LED 0 used for boot status */ + +#ifndef __ASSEMBLY__ + +/* LEDs */ + +/* led_id_t is unsigned int mask */ +typedef unsigned int led_id_t; + +#define __led_toggle(_msk) \ + do { \ + ((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat ^= (_msk); \ + } while(0) + +#define __led_set(_msk, _st) \ + do { \ + if ((_st)) \ + ((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat |= (_msk); \ + else \ + ((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pedat &= ~(_msk); \ + } while(0) + +#define __led_init(msk, st) __led_set(msk, st) + +#endif + +/*********************************************************************************************************** + + Pin definitions: + + +------+----------------+--------+------------------------------------------------------------ + | # | Name | Type | Comment + +------+----------------+--------+------------------------------------------------------------ + | PA3 | SPIEN_MAX | Output | MAX serial to uart chip select + | PA7 | DSP_INT | Output | DSP interrupt + | PA10 | DSP_RESET | Output | DSP reset + | PA14 | USBOE | Output | USB (1) + | PA15 | USBRXD | Output | USB (1) + | PB19 | BT_RTS | Output | Bluetooth (0) + | PB23 | BT_CTS | Output | Bluetooth (0) + | PB26 | SPIEN_SEP | Output | Serial EEPROM chip select + | PB27 | SPICS_DISP | Output | Display chip select + | PB28 | SPI_RXD_3V | Input | SPI Data Rx + | PB29 | SPI_TXD | Output | SPI Data Tx + | PB30 | SPI_CLK | Output | SPI Clock + | PC10 | DISPA0 | Output | Display A0 + | PC11 | BACKLIGHT | Output | Display backlit + | PC12 | SPI2RXD | Input | 2nd SPI RXD + | PC13 | SPI2TXD | Output | 2nd SPI TXD + | PC15 | SPI2CLK | Output | 2nd SPI CLK + | PE17 | F_ALE | Output | NAND F_ALE + | PE18 | F_CLE | Output | NAND F_CLE + | PE20 | F_CE | Output | NAND F_CE + | PE24 | SPICS_SCOUT | Output | Codec chip select + | PE27 | SPICS_ER | Output | External serial register CS + | PE28 | LEDIO1 | Output | LED + | PE29 | LEDIO2 | Output | LED hook for A (TA2) + | PE30 | LEDIO3 | Output | LED hook for A (TA2) + | PE31 | F_RY_BY | Input | NAND F_RY_BY + +------+----------------+--------+--------------------------------------------------- + + Chip selects: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | CS0 | CS0 | Boot flash + | CS1 | CS_FLASH | NAND flash + | CS2 | CS_DSP | DSP + | CS3 | DCS_DRAM | DRAM + +------+----------------+------------------------------------------------------------ + + Interrupts: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | IRQ1 | IRQ_DSP | DSP interrupt + | IRQ3 | S_INTER | DUSLIC ??? + | IRQ4 | F_RY_BY | NAND + | IRQ7 | IRQ_MAX | MAX 3100 interrupt + +------+----------------+------------------------------------------------------------ + + Interrupts on PCMCIA pins: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | IP_A0| PHY1_LINK | Link status changed for #1 Ethernet interface + | IP_A1| PHY2_LINK | Link status changed for #2 Ethernet interface + | IP_A2| RMII1_MDINT | PHY interrupt for #1 + | IP_A3| RMII2_MDINT | PHY interrupt for #2 + +------+----------------+------------------------------------------------------------ + +*************************************************************************************************/ + +#define CONFIG_SED156X 1 /* use SED156X */ +#define CONFIG_SED156X_PG12864Q 1 /* type of display used */ + +/* serial interfacing macros */ + +#define SED156X_SPI_RXD_PORT (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_RXD_MASK 0x00000008 + +#define SED156X_SPI_TXD_PORT (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_TXD_MASK 0x00000004 + +#define SED156X_SPI_CLK_PORT (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) +#define SED156X_SPI_CLK_MASK 0x00000002 + +#define SED156X_CS_PORT (((volatile immap_t *)CFG_IMMR)->im_cpm.cp_pbdat) +#define SED156X_CS_MASK 0x00000010 + +#define SED156X_A0_PORT (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat) +#define SED156X_A0_MASK 0x0020 + +/*************************************************************************************************/ + +#define CFG_CONSOLE_IS_IN_ENV 1 +#define CFG_CONSOLE_OVERWRITE_ROUTINE 1 +#define CFG_CONSOLE_ENV_OVERWRITE 1 + +/*************************************************************************************************/ + +/* use board specific hardware */ +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG +#define CONFIG_SHOW_ACTIVITY + +/*************************************************************************************************/ + +/* phone console configuration */ + +#define PHONE_CONSOLE_POLL_HZ (CFG_HZ/200) /* poll every 5ms */ + +/*************************************************************************************************/ + +#define CONFIG_CDP_DEVICE_ID 20 +#define CONFIG_CDP_DEVICE_ID_PREFIX "NP" /* netphone */ +#define CONFIG_CDP_PORT_ID "eth%d" +#define CONFIG_CDP_CAPABILITIES 0x00000010 +#define CONFIG_CDP_VERSION "u-boot" " " __DATE__ " " __TIME__ +#define CONFIG_CDP_PLATFORM "Intracom NetPhone" +#define CONFIG_CDP_TRIGGER 0x20020001 +#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */ +#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone */ + +/*************************************************************************************************/ + +#define CONFIG_AUTO_COMPLETE 1 + +/*************************************************************************************************/ + +#endif /* __CONFIG_H */ diff --git a/include/configs/NETTA.h b/include/configs/NETTA.h new file mode 100644 index 0000000..76e9cb4 --- /dev/null +++ b/include/configs/NETTA.h @@ -0,0 +1,745 @@ +/* + * (C) Copyright 2000-2004 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* + * Pantelis Antoniou, Intracom S.A., panto@intracom.gr + * U-Boot port on NetTA4 board + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC885 1 /* This is a MPC885 CPU */ +#define CONFIG_NETTA 1 /* ...on a NetTA board */ + +#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ +#undef CONFIG_8xx_CONS_SMC2 +#undef CONFIG_8xx_CONS_NONE + +#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ + +/* #define CONFIG_XIN 10000000 */ +#define CONFIG_XIN 50000000 +#define MPC8XX_HZ 120000000 +/* #define MPC8XX_HZ 100000000 */ +/* #define MPC8XX_HZ 50000000 */ +/* #define MPC8XX_HZ 80000000 */ + +#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */ + +#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo" + +#undef CONFIG_BOOTARGS +#define CONFIG_BOOTCOMMAND \ + "tftpboot; " \ + "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \ + "bootm" + +#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */ +#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ +#define CONFIG_HW_WATCHDOG + +#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */ + +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE | CONFIG_BOOTP_NISDOMAIN) + +#undef CONFIG_MAC_PARTITION +#undef CONFIG_DOS_PARTITION + +#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */ + +#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */ +#define FEC_ENET 1 /* eth.c needs it that way... */ +#undef CFG_DISCOVER_PHY /* do not discover phys */ +#define CONFIG_MII 1 +#define CONFIG_RMII 1 /* use RMII interface */ + +#if defined(CONFIG_NETTA_ISDN) +#define CONFIG_ETHER_ON_FEC1 1 +#define CONFIG_FEC1_PHY 1 /* phy address of FEC1 */ +#define CONFIG_FEC1_PHY_NORXERR 1 +#undef CONFIG_ETHER_ON_FEC2 +#else +#define CONFIG_ETHER_ON_FEC1 1 +#define CONFIG_FEC1_PHY 8 /* phy address of FEC1 */ +#define CONFIG_FEC1_PHY_NORXERR 1 +#define CONFIG_ETHER_ON_FEC2 1 +#define CONFIG_FEC2_PHY 1 /* phy address of FEC2 */ +#define CONFIG_FEC2_PHY_NORXERR 1 +#endif + +#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */ + +/* POST support */ +#define CONFIG_POST (CFG_POST_MEMORY | \ + CFG_POST_DSP ) + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_NAND | \ + CFG_CMD_DHCP | \ + CFG_CMD_PING | \ + CFG_CMD_MII | \ + CFG_CMD_PCMCIA | CFG_CMD_IDE | CFG_CMD_FAT | \ + CFG_CMD_DIAG | \ + CFG_CMD_CDP \ + ) + +#define CONFIG_BOARD_EARLY_INIT_F 1 +#define CONFIG_MISC_INIT_R + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#define CFG_HUSH_PARSER 1 +#define CFG_PROMPT_HUSH_PS2 "> " + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0300000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } + +/* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ +/*----------------------------------------------------------------------- + * Internal Memory Mapped Register + */ +#define CFG_IMMR 0xFF000000 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ +#define CFG_INIT_RAM_ADDR CFG_IMMR +#define CFG_INIT_RAM_END 0x3000 /* End of used area in DPRAM */ +#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_FLASH_BASE 0x40000000 +#if defined(DEBUG) +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#else +#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#endif +#define CFG_MONITOR_BASE CFG_FLASH_BASE +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_SECT_SIZE 0x10000 + +#define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x60000) +#define CFG_ENV_OFFSET 0 +#define CFG_ENV_SIZE 0x4000 + +#define CFG_ENV_ADDR_REDUND (CFG_FLASH_BASE + 0x70000) +#define CFG_ENV_OFFSET_REDUND 0 +#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */ +#endif + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 11-9 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze + */ +#if defined(CONFIG_WATCHDOG) +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ + SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) +#else +#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) +#endif + +/*----------------------------------------------------------------------- + * SIUMCR - SIU Module Configuration 11-6 + *----------------------------------------------------------------------- + * PCMCIA config., multi-function pin tri-state + */ +#ifndef CONFIG_CAN_DRIVER +#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#else /* we must activate GPL5 in the SIUMCR for CAN */ +#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC) +#endif /* CONFIG_CAN_DRIVER */ + +/*----------------------------------------------------------------------- + * TBSCR - Time Base Status and Control 11-26 + *----------------------------------------------------------------------- + * Clear Reference Interrupt Status, Timebase freezing enabled + */ +#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) + +/*----------------------------------------------------------------------- + * RTCSC - Real-Time Clock Status and Control Register 11-27 + *----------------------------------------------------------------------- + */ +#define CFG_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) + +/*----------------------------------------------------------------------- + * PISCR - Periodic Interrupt Status and Control 11-31 + *----------------------------------------------------------------------- + * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled + */ +#define CFG_PISCR (PISCR_PS | PISCR_PITF) + +/*----------------------------------------------------------------------- + * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 + *----------------------------------------------------------------------- + * Reset PLL lock status sticky bit, timer expired status bit and timer + * interrupt status bit + * + */ + +#if CONFIG_XIN == 10000000 + +#if MPC8XX_HZ == 120000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 50000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 25000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 40000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 75000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 10MHz +#endif + +#elif CONFIG_XIN == 50000000 + +#if MPC8XX_HZ == 120000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 100000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 80000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (0 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#elif MPC8XX_HZ == 50000000 +#define CFG_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \ + (1 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \ + PLPRCR_TEXPS) +#else +#error unsupported CPU freq for XIN = 50MHz +#endif + +#else + +#error unsupported XIN freq +#endif + + +/* + *----------------------------------------------------------------------- + * SCCR - System Clock and reset Control Register 15-27 + *----------------------------------------------------------------------- + * Set clock output, timebase and RTC source and divider, + * power management and some other internal clocks + */ + +#define SCCR_MASK SCCR_EBDF11 +#if MPC8XX_HZ > 66666666 +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL001 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00 | SCCR_EBDF01) +#else +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00) +#endif + +/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- + * + */ +/*#define CFG_DER 0x2002000F*/ +#define CFG_DER 0 + +/* + * Init Memory Controller: + * + * BR0/1 and OR0/1 (FLASH) + */ + +#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */ + +/* used to re-map FLASH both when starting from SRAM or FLASH: + * restrict access enough to keep SRAM working (if any) + * but not too much to meddle with FLASH accesses + */ +#define CFG_REMAP_OR_AM 0x80000000 /* OR addr mask */ +#define CFG_PRELIM_OR_AM 0xE0000000 /* OR addr mask */ + +/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */ +#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX) + +#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) +#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V ) + +/* + * BR3 and OR3 (SDRAM) + * + */ +#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */ +#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */ + +/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */ +#define CFG_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS) + +#define CFG_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CFG_OR_TIMING_SDRAM) +#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V) + +/* + * Memory Periodic Timer Prescaler + */ + +/* + * Memory Periodic Timer Prescaler + * + * The Divider for PTA (refresh timer) configuration is based on an + * example SDRAM configuration (64 MBit, one bank). The adjustment to + * the number of chip selects (NCS) and the actually needed refresh + * rate is done by setting MPTPR. + * + * PTA is calculated from + * PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS) + * + * gclk CPU clock (not bus clock!) + * Trefresh Refresh cycle * 4 (four word bursts used) + * + * 4096 Rows from SDRAM example configuration + * 1000 factor s -> ms + * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration + * 4 Number of refresh cycles per period + * 64 Refresh cycle in ms per number of rows + * -------------------------------------------- + * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000 + * + * 50 MHz => 50.000.000 / Divider = 98 + * 66 Mhz => 66.000.000 / Divider = 129 + * 80 Mhz => 80.000.000 / Divider = 156 + */ + +#if MPC8XX_HZ == 120000000 +#define CFG_MAMR_PTA 234 +#elif MPC8XX_HZ == 100000000 +#define CFG_MAMR_PTA 195 +#elif MPC8XX_HZ == 80000000 +#define CFG_MAMR_PTA 156 +#elif MPC8XX_HZ == 50000000 +#define CFG_MAMR_PTA 98 +#else +#error Unknown frequency +#endif + + +/* + * For 16 MBit, refresh rates could be 31.3 us + * (= 64 ms / 2K = 125 / quad bursts). + * For a simpler initialization, 15.6 us is used instead. + * + * #define CFG_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks + * #define CFG_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank + */ +#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ + +/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ +#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ +#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ + +/* + * MAMR settings for SDRAM + */ + +/* 8 column SDRAM */ +#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* 9 column SDRAM */ +#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ + MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ + MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#define CONFIG_ARTOS /* include ARTOS support */ + +#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */ + +/*********************************************************************************************************** + + Pin definitions: + + +------+----------------+--------+------------------------------------------------------------ + | # | Name | Type | Comment + +------+----------------+--------+------------------------------------------------------------ + | PA3 | OK_ETH_3V | Input | CISCO Ethernet power OK + | | | | (NetRoute: FEC1, TA: FEC2) (0=power OK) + | PA6 | P_VCCD1 | Output | TPS2211A PCMCIA + | PA7 | DCL1_3V | Periph | IDL1 PCM clock + | PA8 | DSP_DR1 | Periph | IDL1 PCM Data Rx + | PA9 | L1TXDA | Periph | IDL1 PCM Data Tx + | PA10 | P_VCCD0 | Output | TPS2211A PCMCIA + | PA12 | P_SHDN | Output | TPS2211A PCMCIA + | PA13 | ETH_LOOP | Output | CISCO Loopback remote power + | | | | (NetRoute: FEC1, TA: FEC2) (1=NORMAL) + | PA14 | P_VPPD0 | Output | TPS2211A PCMCIA + | PA15 | P_VPPD1 | Output | TPS2211A PCMCIA + | PB14 | SPIEN_FXO | Output | SPI CS for FXO daughter-board + | PB15 | SPIEN_S1 | Output | SPI CS for S-interface 1 (NetRoute only) + | PB16 | DREQ1 | Output | D channel request for S-interface chip 1. + | PB17 | L1ST3 | Periph | IDL1 timeslot enable signal for PPC + | PB18 | L1ST2 | Periph | IDL1 timeslot enable signal for PPC + | PB19 | SPIEN_S2 | Output | SPI CS for S-interface 2 (NetRoute only) + | PB20 | SPIEN_SEEPROM | Output | SPI CS for serial eeprom + | PB21 | LEDIO | Output | Led mode indication for PHY + | PB22 | UART_CTS | Input | UART CTS + | PB23 | UART_RTS | Output | UART RTS + | PB24 | UART_RX | Periph | UART Data Rx + | PB25 | UART_TX | Periph | UART Data Tx + | PB26 | RMII-MDC | Periph | Free for future use (MII mgt clock) + | PB27 | RMII-MDIO | Periph | Free for future use (MII mgt data) + | PB28 | SPI_RXD_3V | Input | SPI Data Rx + | PB29 | SPI_TXD | Output | SPI Data Tx + | PB30 | SPI_CLK | Output | SPI Clock + | PB31 | RMII1-REFCLK | Periph | RMII reference clock for FEC1 + | PC4 | PHY1_LINK | Input | PHY link state FEC1 (interrupt) + | PC5 | PHY2_LINK | Input | PHY link state FEC2 (interrupt) + | PC6 | RMII1-MDINT | Input | PHY prog interrupt FEC1 (interrupt) + | PC7 | RMII2-MDINT | Input | PHY prog interrupt FEC1 (interrupt) + | PC8 | P_OC | Input | TPS2211A PCMCIA overcurrent (interrupt) (1=OK) + | PC9 | COM_HOOK1 | Input | Codec interrupt chip #1 (interrupt) + | PC10 | COM_HOOK2 | Input | Codec interrupt chip #2 (interrupt) + | PC11 | COM_HOOK4 | Input | Codec interrupt chip #4 (interrupt) + | PC12 | COM_HOOK3 | Input | Codec interrupt chip #3 (interrupt) + | PC13 | F_RY_BY | Input | NAND ready signal (interrupt) + | PC14 | FAN_OK | Input | Fan status signal (interrupt) (1=OK) + | PC15 | PC15_DIRECT0 | Periph | PCMCIA DMA request. + | PD3 | F_ALE | Output | NAND + | PD4 | F_CLE | Output | NAND + | PD5 | F_CE | Output | NAND + | PD6 | DSP_INT | Output | DSP debug interrupt + | PD7 | DSP_RESET | Output | DSP reset + | PD8 | RMII_MDC | Periph | MII mgt clock + | PD9 | SPIEN_C1 | Output | SPI CS for codec #1 + | PD10 | SPIEN_C2 | Output | SPI CS for codec #2 + | PD11 | SPIEN_C3 | Output | SPI CS for codec #3 + | PD12 | FSC2 | Periph | IDL2 frame sync + | PD13 | DGRANT2 | Input | D channel grant from S #2 + | PD14 | SPIEN_C4 | Output | SPI CS for codec #4 + | PD15 | TP700 | Output | Testpoint for software debugging + | PE14 | RMII2-TXD0 | Periph | FEC2 transmit data + | PE15 | RMII2-TXD1 | Periph | FEC2 transmit data + | PE16 | RMII2-REFCLK | Periph | TA: RMII ref clock for + | | DCL2 | Periph | NetRoute: PCM clock #2 + | PE17 | TP703 | Output | Testpoint for software debugging + | PE18 | DGRANT1 | Input | D channel grant from S #1 + | PE19 | RMII2-TXEN | Periph | TA: FEC2 tx enable + | | PCM2OUT | Periph | NetRoute: Tx data for IDL2 + | PE20 | FSC1 | Periph | IDL1 frame sync + | PE21 | RMII2-RXD0 | Periph | FEC2 receive data + | PE22 | RMII2-RXD1 | Periph | FEC2 receive data + | PE23 | L1ST1 | Periph | IDL1 timeslot enable signal for PPC + | PE24 | U-N1 | Output | Select user/network for S #1 (0=user) + | PE25 | U-N2 | Output | Select user/network for S #2 (0=user) + | PE26 | RMII2-RXDV | Periph | FEC2 valid + | PE27 | DREQ2 | Output | D channel request for S #2. + | PE28 | FPGA_DONE | Input | FPGA done signal + | PE29 | FPGA_INIT | Output | FPGA init signal + | PE30 | UDOUT2_3V | Input | IDL2 PCM input + | PE31 | | | Free + +------+----------------+--------+--------------------------------------------------- + + Chip selects: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | CS0 | CS0 | Boot flash + | CS1 | CS_FLASH | NAND flash + | CS2 | CS_DSP | DSP + | CS3 | DCS_DRAM | DRAM + | CS4 | CS_ER1 | External output register + +------+----------------+------------------------------------------------------------ + + Interrupts: + + +------+----------------+------------------------------------------------------------ + | # | Name | Comment + +------+----------------+------------------------------------------------------------ + | IRQ1 | UINTER_3V | S interupt chips interrupt (common) + | IRQ3 | IRQ_DSP | DSP interrupt + | IRQ4 | IRQ_DSP1 | Extra DSP interrupt + +------+----------------+------------------------------------------------------------ + +*************************************************************************************************/ + +#define DSP_SIZE 0x00010000 /* 64K */ +#define NAND_SIZE 0x00010000 /* 64K */ +#define ER_SIZE 0x00010000 /* 64K */ +#define DUMMY_SIZE 0x00010000 /* 64K */ + +#define DSP_BASE 0xF1000000 +#define NAND_BASE 0xF1010000 +#define ER_BASE 0xF1020000 +#define DUMMY_BASE 0xF1FF0000 + +/****************************************************************/ + +/* NAND */ +#define CFG_NAND_BASE NAND_BASE +#define CONFIG_MTD_NAND_ECC_JFFS2 + +#define CFG_MAX_NAND_DEVICE 1 +#define NAND_NO_RB + +#define SECTORSIZE 512 +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +/* ALE = PD3, CLE = PD4, CE = PD5, F_RY_BY = PC13 */ +#define NAND_DISABLE_CE(nand) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 5)); \ + } while(0) + +#define NAND_ENABLE_CE(nand) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 5)); \ + } while(0) + +#define NAND_CTL_CLRALE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 3)); \ + } while(0) + +#define NAND_CTL_SETALE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 3)); \ + } while(0) + +#define NAND_CTL_CLRCLE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 4)); \ + } while(0) + +#define NAND_CTL_SETCLE(nandptr) \ + do { \ + (((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 4)); \ + } while(0) + +#ifndef NAND_NO_RB +#define NAND_WAIT_READY(nand) \ + do { \ + while ((((volatile immap_t *)CFG_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 13))) == 0) { \ + WATCHDOG_RESET(); \ + } \ + } while (0) +#else +#define NAND_WAIT_READY(nand) udelay(12) +#endif + +#define WRITE_NAND_COMMAND(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define WRITE_NAND_ADDRESS(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define WRITE_NAND(d, adr) \ + do { \ + *(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \ + } while(0) + +#define READ_NAND(adr) \ + ((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr))) + +/*****************************************************************************/ + +#if 1 +/*----------------------------------------------------------------------- + * PCMCIA stuff + *----------------------------------------------------------------------- + */ + +#define CFG_PCMCIA_MEM_ADDR (0xE0000000) +#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_DMA_ADDR (0xE4000000) +#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000) +#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 ) +#define CFG_PCMCIA_IO_ADDR (0xEC000000) +#define CFG_PCMCIA_IO_SIZE ( 64 << 20 ) + +/*----------------------------------------------------------------------- + * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter) + *----------------------------------------------------------------------- + */ + +#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ + +#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ +#undef CONFIG_IDE_LED /* LED for ide not supported */ +#undef CONFIG_IDE_RESET /* reset for ide not supported */ + +#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ + +#define CFG_ATA_IDE0_OFFSET 0x0000 + +#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR + +/* Offset for data I/O */ +#define CFG_ATA_DATA_OFFSET (CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for normal register accesses */ +#define CFG_ATA_REG_OFFSET (2 * CFG_PCMCIA_MEM_SIZE + 0x320) + +/* Offset for alternate registers */ +#define CFG_ATA_ALT_OFFSET 0x0100 + +#define CONFIG_MAC_PARTITION +#define CONFIG_DOS_PARTITION +#endif + +/*************************************************************************************************/ + +#define CONFIG_CDP_DEVICE_ID 20 +#define CONFIG_CDP_DEVICE_ID_PREFIX "NT" /* netta */ +#define CONFIG_CDP_PORT_ID "eth%d" +#define CONFIG_CDP_CAPABILITIES 0x00000010 +#define CONFIG_CDP_VERSION "u-boot 1.0" " " __DATE__ " " __TIME__ +#define CONFIG_CDP_PLATFORM "Intracom NetTA" +#define CONFIG_CDP_TRIGGER 0x20020001 +#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */ +#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone? */ + +/*************************************************************************************************/ + +#define CONFIG_AUTO_COMPLETE 1 + +/*************************************************************************************************/ + +#endif /* __CONFIG_H */ diff --git a/include/configs/NETVIA.h b/include/configs/NETVIA.h index 46505b6..8f93a49 100644 --- a/include/configs/NETVIA.h +++ b/include/configs/NETVIA.h @@ -36,7 +36,6 @@ #define CONFIG_MPC850 1 /* This is a MPC850 CPU */ #define CONFIG_NETVIA 1 /* ...on a NetVia board */ -#undef CONFIG_NETVIA_PLL_CLOCK /* PLL or fixed crystal clock */ #if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1 #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ @@ -49,14 +48,8 @@ #define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */ -#ifdef CONFIG_NETVIA_PLL_CLOCK -/* XXX make sure that you calculate these two correctly */ -#define CFG_GCLK_MF 1350 -#define CONFIG_8xx_GCLK_FREQ 44236800 -#else -#define CFG_GCLK_MF 1 -#define CONFIG_8xx_GCLK_FREQ 50000000 -#endif +#define CONFIG_XIN 10000000 +#define CONFIG_8xx_GCLK_FREQ 80000000 #if 0 #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ @@ -253,22 +246,34 @@ * Reset PLL lock status sticky bit, timer expired status bit and timer * interrupt status bit * - */ - -#define CFG_PLPRCR ( ((CFG_GCLK_MF-1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- + * + *----------------------------------------------------------------------- * SCCR - System Clock and reset Control Register 15-27 *----------------------------------------------------------------------- * Set clock output, timebase and RTC source and divider, * power management and some other internal clocks */ + #define SCCR_MASK SCCR_EBDF11 + +#if CONFIG_8xx_GCLK_FREQ == 50000000 + +#define CFG_PLPRCR ( ((5 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) #define CFG_SCCR (SCCR_TBS | \ SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ SCCR_DFALCD00) +#elif CONFIG_8xx_GCLK_FREQ == 80000000 + +#define CFG_PLPRCR ( ((8 - 1) << PLPRCR_MF_SHIFT) | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) +#define CFG_SCCR (SCCR_TBS | \ + SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ + SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ + SCCR_DFALCD00 | SCCR_EBDF01) + +#endif + /*----------------------------------------------------------------------- * *----------------------------------------------------------------------- @@ -520,6 +525,6 @@ static inline void __led_set(led_id_t mask, int state) #endif -/****************************************************************/ +/*************************************************************************************************/ #endif /* __CONFIG_H */ |