diff options
Diffstat (limited to 'include/configs/zylonite.h')
| -rw-r--r-- | include/configs/zylonite.h | 140 |
1 files changed, 56 insertions, 84 deletions
diff --git a/include/configs/zylonite.h b/include/configs/zylonite.h index 4232d50..c6aa8ec 100644 --- a/include/configs/zylonite.h +++ b/include/configs/zylonite.h @@ -76,14 +76,17 @@ #define CONFIG_BAUDRATE 115200 -/* #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT) */ #ifdef TURN_ON_ETHERNET # define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING) #else -# define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_NET) +# define CONFIG_COMMANDS ((CONFIG_CMD_DFL \ + | CFG_CMD_ENV \ + | CFG_CMD_NAND) \ + & ~(CFG_CMD_NET \ + | CFG_CMD_FLASH \ + | CFG_CMD_IMLS)) #endif - /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -127,8 +130,11 @@ #define CFG_LOAD_ADDR (CFG_DRAM_BASE + 0x8000) /* default load address */ -#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */ -#define CFG_CPUSPEED 0x161 /* set core clock to 400/200/100 MHz */ +#define CFG_HZ 3250000 /* incrementer freq: 3.25 MHz */ + +/* Monahans Core Frequency */ +#define CFG_MONAHANS_RUN_MODE_OSC_RATIO 16 /* valid values: 8, 16, 24, 31 */ +#define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 1 /* valid values: 1, 2 */ /* valid baudrates */ #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } @@ -159,98 +165,64 @@ #define PHYS_SDRAM_4 0xac000000 /* SDRAM Bank #4 */ #define PHYS_SDRAM_4_SIZE 0x00000000 /* 0 MB */ -#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ -#define PHYS_FLASH_2 0x04000000 /* Flash Bank #2 */ -#define PHYS_FLASH_SIZE 0x02000000 /* 32 MB */ -#define PHYS_FLASH_BANK_SIZE 0x02000000 /* 32 MB Banks */ -#define PHYS_FLASH_SECT_SIZE 0x00040000 /* 256 KB sectors (x2) */ +#define CFG_DRAM_BASE 0x80000000 /* at CS0 */ +#define CFG_DRAM_SIZE 0x04000000 /* 64 MB Ram */ -#define CFG_DRAM_BASE 0xa0000000 -#define CFG_DRAM_SIZE 0x04000000 +#undef CFG_SKIP_DRAM_SCRUB -#define CFG_FLASH_BASE PHYS_FLASH_1 - -#define FPGA_REGS_BASE_PHYSICAL 0x08000000 /* - * GPIO settings + * NAND Flash */ -#define CFG_GPSR0_VAL 0x00008000 -#define CFG_GPSR1_VAL 0x00FC0382 -#define CFG_GPSR2_VAL 0x0001FFFF -#define CFG_GPCR0_VAL 0x00000000 -#define CFG_GPCR1_VAL 0x00000000 -#define CFG_GPCR2_VAL 0x00000000 -#define CFG_GPDR0_VAL 0x0060A800 -#define CFG_GPDR1_VAL 0x00FF0382 -#define CFG_GPDR2_VAL 0x0001C000 -#define CFG_GAFR0_L_VAL 0x98400000 -#define CFG_GAFR0_U_VAL 0x00002950 -#define CFG_GAFR1_L_VAL 0x000A9558 -#define CFG_GAFR1_U_VAL 0x0005AAAA -#define CFG_GAFR2_L_VAL 0xA0000000 -#define CFG_GAFR2_U_VAL 0x00000002 - -#define CFG_PSSR_VAL 0x20 +/* Use the new NAND code. (BOARDLIBS = drivers/nand/libnand.a required) */ +#define CONFIG_NEW_NAND_CODE +#define CFG_NAND0_BASE 0x0 +#undef CFG_NAND1_BASE -/* - * Memory settings - */ -#define CFG_MSC0_VAL 0x23F223F2 -#define CFG_MSC1_VAL 0x3FF1A441 -#define CFG_MSC2_VAL 0x7FF97FF1 -#define CFG_MDCNFG_VAL 0x00001AC9 -#define CFG_MDREFR_VAL 0x00018018 -#define CFG_MDMRS_VAL 0x00000000 +#define CFG_NAND_BASE_LIST { CFG_NAND0_BASE } +#define CFG_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ -/* - * PCMCIA and CF Interfaces - */ -#define CFG_MECR_VAL 0x00000000 -#define CFG_MCMEM0_VAL 0x00010504 -#define CFG_MCMEM1_VAL 0x00010504 -#define CFG_MCATT0_VAL 0x00010504 -#define CFG_MCATT1_VAL 0x00010504 -#define CFG_MCIO0_VAL 0x00004715 -#define CFG_MCIO1_VAL 0x00004715 +/* nand timeout values */ +#define CFG_NAND_PROG_ERASE_TO 3000 +#define CFG_NAND_OTHER_TO 100 +#define CFG_NAND_SENDCMD_RETRY 3 +#undef NAND_ALLOW_ERASE_ALL /* Allow erasing bad blocks - don't use */ -#define _LED 0x08000010 -#define LED_BLANK 0x08000040 +/* NAND Timing Parameters (in ns) */ +#define NAND_TIMING_tCH 10 +#define NAND_TIMING_tCS 0 +#define NAND_TIMING_tWH 20 +#define NAND_TIMING_tWP 40 -/* - * FLASH and environment organization - */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define NAND_TIMING_tRH 20 +#define NAND_TIMING_tRP 40 -/* timeout values are in ticks */ -#define CFG_FLASH_ERASE_TOUT (25*CFG_HZ) /* Timeout for Flash Erase */ -#define CFG_FLASH_WRITE_TOUT (25*CFG_HZ) /* Timeout for Flash Write */ +#define NAND_TIMING_tR 11123 +#define NAND_TIMING_tWHR 100 +#define NAND_TIMING_tAR 10 -/* NOTE: many default partitioning schemes assume the kernel starts at the - * second sector, not an environment. You have been warned! - */ -#define CFG_MONITOR_LEN PHYS_FLASH_SECT_SIZE +/* NAND debugging */ +#define CFG_DFC_DEBUG1 /* usefull */ +#undef CFG_DFC_DEBUG2 /* noisy */ +#undef CFG_DFC_DEBUG3 /* extremly noisy */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_ADDR (PHYS_FLASH_1 + PHYS_FLASH_SECT_SIZE) -#define CFG_ENV_SECT_SIZE PHYS_FLASH_SECT_SIZE -#define CFG_ENV_SIZE (PHYS_FLASH_SECT_SIZE / 16) +#define CONFIG_MTD_DEBUG +#define CONFIG_MTD_DEBUG_VERBOSE 1 +#define ADDR_COLUMN 1 +#define ADDR_PAGE 2 +#define ADDR_COLUMN_PAGE 3 + +#define NAND_ChipID_UNKNOWN 0x00 +#define NAND_MAX_FLOORS 1 +#define NAND_MAX_CHIPS 1 + +#define CFG_NO_FLASH 1 + +#define CFG_ENV_IS_IN_NAND 1 +#define CFG_ENV_OFFSET 0x40000 +#define CFG_ENV_OFFSET_REDUND 0x44000 +#define CFG_ENV_SIZE 0x4000 -/* - * FPGA Offsets - */ -#define WHOAMI_OFFSET 0x00 -#define HEXLED_OFFSET 0x10 -#define BLANKLED_OFFSET 0x40 -#define DISCRETELED_OFFSET 0x40 -#define CNFG_SWITCHES_OFFSET 0x50 -#define USER_SWITCHES_OFFSET 0x60 -#define MISC_WR_OFFSET 0x80 -#define MISC_RD_OFFSET 0x90 -#define INT_MASK_OFFSET 0xC0 -#define INT_CLEAR_OFFSET 0xD0 -#define GP_OFFSET 0x100 #endif /* __CONFIG_H */ |