diff options
Diffstat (limited to 'include/configs/yucca.h')
| -rw-r--r-- | include/configs/yucca.h | 71 |
1 files changed, 41 insertions, 30 deletions
diff --git a/include/configs/yucca.h b/include/configs/yucca.h index 7f8b022..74033b4 100644 --- a/include/configs/yucca.h +++ b/include/configs/yucca.h @@ -46,7 +46,6 @@ #define EXTCLK_83 83333333 #define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ #undef CONFIG_SHOW_BOOT_PROGRESS #undef CONFIG_STRESS @@ -69,11 +68,11 @@ #define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ #define CFG_PCIE0_CFGBASE 0xc0000000 -#define CFG_PCIE0_XCFGBASE 0xc0000400 -#define CFG_PCIE1_CFGBASE 0xc0001000 -#define CFG_PCIE1_XCFGBASE 0xc0001400 -#define CFG_PCIE2_CFGBASE 0xc0002000 -#define CFG_PCIE2_XCFGBASE 0xc0002400 +#define CFG_PCIE1_CFGBASE 0xc1000000 +#define CFG_PCIE2_CFGBASE 0xc2000000 +#define CFG_PCIE0_XCFGBASE 0xc3000000 +#define CFG_PCIE1_XCFGBASE 0xc3001000 +#define CFG_PCIE2_XCFGBASE 0xc3002000 /* System RAM mapped to PCI space */ #define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE @@ -136,7 +135,7 @@ /* Don't probe these addrs */ #define CFG_I2C_NOPROBES {0x50, 0x52, 0x53, 0x54} -/* #if (CONFIG_COMMANDS & CFG_CMD_EEPROM) */ +/* #if defined(CONFIG_CMD_EEPROM) */ /* #define CFG_I2C_EEPROM_ADDR 0x50 */ /* I2C boot EEPROM */ #define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ /* #endif */ @@ -183,6 +182,7 @@ "cp.b ${fileaddr} FFFB0000 ${filesize};" \ "setenv filesize;saveenv\0" \ "upd=run load;run update\0" \ + "pciconfighost=1\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -191,24 +191,36 @@ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ - CFG_CMD_ASKENV | \ - CFG_CMD_EEPROM | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ELF | \ - CFG_CMD_I2C | \ - CFG_CMD_IRQ | \ - CFG_CMD_MII | \ - CFG_CMD_NET | \ - CFG_CMD_NFS | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <cmd_confdefs.h> + +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_EEPROM +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_DIAG +#define CONFIG_CMD_ELF +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_CMD_NFS +#define CONFIG_CMD_PCI +#define CONFIG_CMD_PING +#define CONFIG_CMD_REGINFO +#define CONFIG_CMD_SDRAM + #define CONFIG_IBM_EMAC4_V4 1 #define CONFIG_MII 1 /* MII PHY management */ @@ -232,7 +244,7 @@ #define CFG_LONGHELP /* undef to save memory */ #define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ @@ -286,10 +298,9 @@ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#undef CONFIG_PCI_CONFIG_HOST_BRIDGE +#define CONFIG_PCI_CONFIG_HOST_BRIDGE /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT /* let board init pci target */ #undef CFG_PCI_MASTER_INIT @@ -314,7 +325,7 @@ */ #define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif @@ -326,7 +337,7 @@ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif |