diff options
Diffstat (limited to 'include/configs/yellowstone.h')
| -rw-r--r-- | include/configs/yellowstone.h | 275 |
1 files changed, 145 insertions, 130 deletions
diff --git a/include/configs/yellowstone.h b/include/configs/yellowstone.h index 2b86337..081cff8 100644 --- a/include/configs/yellowstone.h +++ b/include/configs/yellowstone.h @@ -1,4 +1,6 @@ /* + * (C) Copyright 2005 + * Stefan Roese, DENX Software Engineering, sr@denx.de. * * See file CREDITS for list of people who contributed to this * project. @@ -28,56 +30,53 @@ /*----------------------------------------------------------------------- * High Level Configuration Options *----------------------------------------------------------------------*/ -#define CONFIG_YELLOWSTONE 1 /* Board is BAMBOO */ -#define CONFIG_440GR 1 /* Specific PPC440GR support */ - -#define CONFIG_4xx 1 /* ... PPC4xx family */ -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ -#undef CFG_DRAM_TEST /* disable - takes long time! */ +#define CONFIG_YOLLOWSTONE 1 /* Board is Yellowstone */ +#define CONFIG_440GR 1 /* Specific PPC440EP support */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ #define CONFIG_SYS_CLK_FREQ 66666666 /* external freq to pll */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() */ + /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ -#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 - +#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */ +#define CFG_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ +#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN) +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_PCI_MEMBASE 0xa0000000 /* mapped pci memory*/ +#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 +#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 +#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 /*Don't change either of these*/ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ -#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs */ +#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals*/ +#define CFG_PCI_BASE 0xe0000000 /* internal PCI regs*/ /*Don't change either of these*/ -#define CFG_USB_DEVICE 0x50000000 -#define CFG_NVRAM_BASE_ADDR 0x80000000 -#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_USB_DEVICE 0x50000000 +#define CFG_NVRAM_BASE_ADDR 0x80000000 +#define CFG_BCSR_BASE (CFG_NVRAM_BASE_ADDR | 0x2000) +#define CFG_BOOT_BASE_ADDR 0xf0000000 /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in SDRAM) *----------------------------------------------------------------------*/ -#define CFG_INIT_RAM_ADDR 0xf0000000 /* DCache */ -#define CFG_INIT_RAM_END 0x2000 -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CFG_INIT_RAM_ADDR 0x70000000 /* DCache */ +#define CFG_INIT_RAM_END (8 << 10) +#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data*/ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) #define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ -#define CFG_KBYTES_SDRAM ( 128 * 1024) /* 128MB */ -#define CFG_SDRAM_BANKS (2) /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CONFIG_SERIAL_SOFTWARE_FIFO #define CFG_EXT_SERIAL_CLOCK 11059200 /* use external 11.059MHz clk */ -#define CONFIG_BAUDRATE 9600 -#define CONFIG_SERIAL_MULTI 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SERIAL_MULTI 1 /*define this if you want console on UART1*/ #undef CONFIG_UART1_CONSOLE @@ -85,29 +84,50 @@ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- - * NVRAM/RTC - * - * NOTE: The RTC registers are located at 0x7FFF0 - 0x7FFFF - * The DS1558 code assumes this condition - * + * Environment *----------------------------------------------------------------------*/ -#define CFG_NVRAM_SIZE (0x2000 - 0x10) /* NVRAM size(8k)- RTC regs */ -#define CONFIG_RTC_DS1556 1 /* DS1556 RTC */ +/* + * Define here the location of the environment variables (FLASH or EEPROM). + * Note: DENX encourages to use redundant environment in FLASH. + */ +#if 1 +#define CFG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ +#else +#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ +#endif /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 256 /* sectors per device */ +#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ +#define CFG_FLASH_CFI_AMD_RESET 1 /* AMD RESET for STM 29W320DB! */ + +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#undef CFG_FLASH_CHECKSUM #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 120000 /* Timeout for Flash Write (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ + +#ifdef CFG_ENV_IS_IN_FLASH +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#endif /* CFG_ENV_IS_IN_FLASH */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ +#define CFG_KBYTES_SDRAM (128 * 1024) /* 128MB */ +#define CFG_SDRAM_BANKS (2) + /*----------------------------------------------------------------------- * I2C @@ -117,44 +137,70 @@ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F - -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ -#undef CFG_ENV_IS_IN_NVRAM /*No NVRAM on board*/ -#undef CFG_ENV_IS_IN_FLASH /* ... not in flash */ -#define CFG_ENV_IS_IN_EEPROM 1 - -/* Define to allow the user to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE - #define CFG_I2C_MULTI_EEPROMS -#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ -#define CFG_ENV_OFFSET 0x0 #define CFG_I2C_EEPROM_ADDR (0xa8>>1) #define CFG_I2C_EEPROM_ADDR_LEN 1 #define CFG_EEPROM_PAGE_WRITE_ENABLE #define CFG_EEPROM_PAGE_WRITE_BITS 3 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -#define CONFIG_BOOTCOMMAND "bootm 0xfe000000" /* autoboot command */ -#define CONFIG_BOOTDELAY 3 /* disable autoboot */ +#ifdef CFG_ENV_IS_IN_EEPROM +#define CFG_ENV_SIZE 0x200 /* Size of Environment vars */ +#define CFG_ENV_OFFSET 0x0 +#endif /* CFG_ENV_IS_IN_EEPROM */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=yellowstone\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=$(serverip):$(rootpath)\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs $(bootargs) " \ + "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \ + ":$(hostname):$(netdev):off panic=1\0" \ + "addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm $(kernel_addr)\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm $(kernel_addr) $(ramdisk_addr)\0" \ + "net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=/tftpboot/yellowstone/uImage\0" \ + "kernel_addr=fc000000\0" \ + "ramdisk_addr=fc100000\0" \ + "load=tftp 100000 /tftpboot/yellowstone/u-boot.bin\0" \ + "update=protect off fff80000 ffffffff;era fff80000 ffffffff;" \ + "cp.b 100000 fff80000 80000;" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#if 0 +#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ +#else +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ +#endif + +#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 /* required for netconsole */ -#define CONFIG_PHY1_ADDR 3 +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_NET_MULTI 1 /* required for netconsole */ +#define CONFIG_PHY1_ADDR 3 #define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */ #define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ -#define CONFIG_NETMASK 255.255.255.0 -#define CONFIG_IPADDR 10.0.4.251 -#define CONFIG_ETHADDR 00:10:EC:00:12:34 -#define CONFIG_ETH1ADDR 00:10:EC:00:12:35 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ -#define CONFIG_SERVERIP 10.0.4.115 /* Partitions */ #define CONFIG_MAC_PARTITION @@ -176,53 +222,20 @@ #define CONFIG_HW_WATCHDOG /* watchdog */ #endif -#ifdef CONFIG_440EP - /* Need to define POST */ -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - /* CFG_CMD_EXT2 |*/ \ - /* CFG_CMD_FAT |*/ \ - CFG_CMD_I2C | \ - /* CFG_CMD_IDE |*/ \ - CFG_CMD_IRQ | \ - /* CFG_CMD_KGDB |*/ \ - CFG_CMD_MII | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_FLASH | \ - /* CFG_CMD_SPI |*/ \ - CFG_CMD_USB | \ - 0 ) & ~CFG_CMD_IMLS) -#else -#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_DIAG | \ - CFG_CMD_ECHO | \ - CFG_CMD_EEPROM | \ - CFG_CMD_ELF | \ - /* CFG_CMD_EXT2 |*/ \ - /* CFG_CMD_FAT |*/ \ - CFG_CMD_I2C | \ - /* CFG_CMD_IDE |*/ \ - CFG_CMD_IRQ | \ - /* CFG_CMD_KGDB |*/ \ - CFG_CMD_MII | \ - CFG_CMD_PCI | \ - CFG_CMD_PING | \ - CFG_CMD_REGINFO | \ - CFG_CMD_SDRAM | \ - CFG_CMD_FLASH | \ - /* CFG_CMD_SPI |*/ \ - 0 ) & ~CFG_CMD_IMLS) -#endif +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM) /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ #include <cmd_confdefs.h> @@ -231,42 +244,42 @@ * Miscellaneous configurable options */ #define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ #define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CONFIG_LYNXKDI 1 /* support kdi files */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_LYNXKDI 1 /* support kdi files */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff *----------------------------------------------------------------------- */ /* General PCI */ -#define CONFIG_PCI /* include pci support */ -#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ -#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP /* do (not) pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/ /* Board-specific PCI */ -#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ +#define CFG_PCI_PRE_INIT /* enable board pci_pre_init() */ #define CFG_PCI_TARGET_INIT #define CFG_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * For booting Linux, the board info and command line data @@ -274,10 +287,11 @@ * the maximum mapped by the Linux kernel during initialization. */ #define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ + /*----------------------------------------------------------------------- * Cache Configuration */ -#define CFG_DCACHE_SIZE 8192 /* For IBM 405 CPUs */ +#define CFG_DCACHE_SIZE (32<<10) /* For IBM 440 CPUs */ #define CFG_CACHELINE_SIZE 32 /* ... */ #if (CONFIG_COMMANDS & CFG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ @@ -295,4 +309,5 @@ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ #endif + #endif /* __CONFIG_H */ |