summaryrefslogtreecommitdiff
path: root/include/configs/walnut.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/walnut.h')
-rw-r--r--include/configs/walnut.h155
1 files changed, 15 insertions, 140 deletions
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index adc420b..e19c5f3 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -38,122 +38,44 @@
#define CONFIG_WALNUT 1 /* ...on a WALNUT board */
/* ...and on a SYCAMORE board */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME walnut
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "hostname=walnut\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=/tftpboot/walnut/uImage\0" \
+/*
+ * Default environment variables
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
"kernel_addr=fff80000\0" \
"ramdisk_addr=fff80000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 100000 /tftpboot/walnut/u-boot.bin\0" \
- "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
- "cp.b 100000 fffc0000 40000;" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
""
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
-#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#endif
-
-#define CONFIG_BAUDRATE 115200
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-
-#define CFG_RX_ETH_BUFFER 16 /* use 16 rx buffer on 405 emac */
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_NET_MULTI /* needed for NetConsole */
-
#define CONFIG_RTC_DS174x 1 /* use DS1743 RTC in Walnut */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
/*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
*/
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SNTP
-
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-/*
* If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
* If CFG_405_UART_ERRATA_59, then UART divisor is 31.
* Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
@@ -167,29 +89,11 @@
#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */
#define CFG_BASE_BAUD 691200
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-
/*-----------------------------------------------------------------------
* I2C stuff
*-----------------------------------------------------------------------
*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_MULTI_EEPROMS
#define CFG_I2C_EEPROM_ADDR (0xa8>>1)
@@ -224,13 +128,8 @@
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFFF80000
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
-#define CFG_MONITOR_BASE (-CFG_MONITOR_LEN)
/*
* Define here the location of the environment variables (FLASH or NVRAM).
@@ -243,13 +142,6 @@
#define CFG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
#endif
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* FLASH organization
*/
@@ -335,21 +227,4 @@
*/
#define SPD_EEPROM_ADDRESS 0x50
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */