diff options
Diffstat (limited to 'include/configs/walnut.h')
| -rw-r--r-- | include/configs/walnut.h | 108 |
1 files changed, 54 insertions, 54 deletions
diff --git a/include/configs/walnut.h b/include/configs/walnut.h index d3d079a..630c0d3 100644 --- a/include/configs/walnut.h +++ b/include/configs/walnut.h @@ -76,30 +76,30 @@ #define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */ /* - * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1. - * If CFG_405_UART_ERRATA_59, then UART divisor is 31. - * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value. + * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1. + * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31. + * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value. * The Linux BASE_BAUD define should match this configuration. * baseBaud = cpuClock/(uartDivisor*16) - * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock, + * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock, * set Linux BASE_BAUD to 403200. */ #undef CONFIG_SERIAL_SOFTWARE_FIFO -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#undef CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#undef CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 691200 /*----------------------------------------------------------------------- * I2C stuff *----------------------------------------------------------------------- */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /*----------------------------------------------------------------------- * PCI stuff @@ -115,20 +115,20 @@ /* resource configuration */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) */ -#define CFG_FLASH_BASE 0xFFF80000 +#define CONFIG_SYS_FLASH_BASE 0xFFF80000 /* * Define here the location of the environment variables (FLASH or NVRAM). @@ -144,24 +144,24 @@ /*----------------------------------------------------------------------- * FLASH organization */ -#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */ +#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ #define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_ADDR0 0x5555 -#define CFG_FLASH_ADDR1 0x2aaa -#define CFG_FLASH_WORD_SIZE unsigned char +#define CONFIG_SYS_FLASH_ADDR0 0x5555 +#define CONFIG_SYS_FLASH_ADDR1 0x2aaa +#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -172,13 +172,13 @@ /*----------------------------------------------------------------------- * NVRAM organization */ -#define CFG_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ -#define CFG_NVRAM_SIZE 0x1ff8 /* NVRAM size */ +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0000000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE 0x1ff8 /* NVRAM size */ #ifdef CONFIG_ENV_IS_IN_NVRAM #define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ #define CONFIG_ENV_ADDR \ - (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ + (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */ #endif /*----------------------------------------------------------------------- @@ -186,39 +186,39 @@ */ /* Memory Bank 0 (Flash Bank 0) initialization */ -#define CFG_EBC_PB0AP 0x9B015480 -#define CFG_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB0AP 0x9B015480 +#define CONFIG_SYS_EBC_PB0CR 0xFFF18000 /* BAS=0xFFF,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB1AP 0x02815480 -#define CFG_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB1AP 0x02815480 +#define CONFIG_SYS_EBC_PB1CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB2AP 0x04815A80 -#define CFG_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB2AP 0x04815A80 +#define CONFIG_SYS_EBC_PB2CR 0xF0118000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB3AP 0x01815280 -#define CFG_EBC_PB3CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB3AP 0x01815280 +#define CONFIG_SYS_EBC_PB3CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */ -#define CFG_EBC_PB7AP 0x01815280 -#define CFG_EBC_PB7CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB7AP 0x01815280 +#define CONFIG_SYS_EBC_PB7CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */ /*----------------------------------------------------------------------- * External peripheral base address *----------------------------------------------------------------------- */ -#define CFG_KEY_REG_BASE_ADDR 0xF0100000 -#define CFG_IR_REG_BASE_ADDR 0xF0200000 -#define CFG_FPGA_REG_BASE_ADDR 0xF0300000 +#define CONFIG_SYS_KEY_REG_BASE_ADDR 0xF0100000 +#define CONFIG_SYS_IR_REG_BASE_ADDR 0xF0200000 +#define CONFIG_SYS_FPGA_REG_BASE_ADDR 0xF0300000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area */ -#define CFG_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */ +#define CONFIG_SYS_INIT_DCACHE_CS 4 /* use cs # 4 for data cache memory */ -#define CFG_INIT_RAM_ADDR 0x40000000 /* inside of SDRAM */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address |