diff options
Diffstat (limited to 'include/configs/uc101.h')
| -rw-r--r-- | include/configs/uc101.h | 198 |
1 files changed, 98 insertions, 100 deletions
diff --git a/include/configs/uc101.h b/include/configs/uc101.h index a186188..553eb25 100644 --- a/include/configs/uc101.h +++ b/include/configs/uc101.h @@ -33,7 +33,7 @@ #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ #define CONFIG_UC101 1 /* UC101 board */ -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ @@ -47,7 +47,7 @@ */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* Partitions */ #define CONFIG_DOS_PARTITION @@ -84,7 +84,7 @@ #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ #if (TEXT_BASE == 0xFFF00000) /* Boot low */ -# define CFG_LOWBOOT 1 +# define CONFIG_SYS_LOWBOOT 1 #endif /* @@ -120,79 +120,77 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ /* * I2C configuration */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration */ -#define CFG_I2C_EEPROM_ADDR 0x58 -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_BITS 4 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 -/* for LM81 */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x58 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* * RTC configuration */ #define CONFIG_RTC_PCF8563 -#define CFG_I2C_RTC_ADDR 0x51 +#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* I2C SYSMON (LM75) */ #define CONFIG_DTT_LM81 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 /* * Flash configuration */ -#define CFG_FLASH_BASE 0xFF800000 +#define CONFIG_SYS_FLASH_BASE 0xFF800000 -#define CFG_FLASH_SIZE 0x00800000 /* 8 MByte */ -#define CFG_MAX_FLASH_SECT 140 /* max num of sects on one chip */ +#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */ +#define CONFIG_SYS_MAX_FLASH_SECT 140 /* max num of sects on one chip */ -#define CFG_ENV_ADDR (TEXT_BASE+0x40000) /* second sector */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks +#define CONFIG_ENV_ADDR (TEXT_BASE+0x40000) /* second sector */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks (= chip selects) */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_CFI_AMD_RESET +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_CFI_AMD_RESET /* * Environment settings */ -#define CFG_ENV_IS_IN_FLASH 1 -#define CFG_ENV_SIZE 0x4000 -#define CFG_ENV_SECT_SIZE 0x10000 -#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE) -#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) +#define CONFIG_ENV_IS_IN_FLASH 1 +#define CONFIG_ENV_SIZE 0x4000 +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) /* * Memory map */ -#define CFG_MBAR 0xF0000000 -#define CFG_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_SRAM_BASE 0x80100000 /* CS 1 */ -#define CFG_DISPLAY_BASE 0x80600000 /* CS 3 */ -#define CFG_IB_MASTER 0xc0510000 /* CS 6 */ -#define CFG_IB_EPLD 0xc0500000 /* CS 7 */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SRAM_BASE 0x80100000 /* CS 1 */ +#define CONFIG_SYS_DISPLAY_BASE 0x80600000 /* CS 3 */ +#define CONFIG_SYS_IB_MASTER 0xc0510000 /* CS 6 */ +#define CONFIG_SYS_IB_EPLD 0xc0500000 /* CS 7 */ /* Settings for XLB = 132 MHz */ #define SDRAM_DDR 1 @@ -204,32 +202,32 @@ #define SDRAM_TAPDELAY 0x10000000 /* SRAM */ -#define SRAM_BASE CFG_SRAM_BASE /* SRAM base address */ +#define SRAM_BASE CONFIG_SYS_SRAM_BASE /* SRAM base address */ #define SRAM_LEN 0x1fffff #define SRAM_END (SRAM_BASE + SRAM_LEN) /* Use ON-Chip SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM #ifdef CONFIG_POST /* preserve space for the post_word at end of on-chip SRAM */ -#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE #else -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE #endif -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CFG_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration @@ -241,7 +239,7 @@ /* * GPIO configuration */ -#define CFG_GPS_PORT_CONFIG 0x4d558044 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x4d558044 /*use Hardware WDT */ #define CONFIG_HW_WATCHDOG @@ -249,30 +247,30 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ /* Enable an alternate, more extensive memory test */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST -#define CFG_MEMTEST_START 0x00300000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 3 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00300000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 3 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x300000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x300000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* @@ -284,41 +282,41 @@ * Various low-level settings */ #if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 #endif -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00045D00 -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00045D00 +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE /* 8Mbit SRAM @0x80100000 */ -#define CFG_CS1_START CFG_SRAM_BASE -#define CFG_CS1_SIZE 0x00200000 -#define CFG_CS1_CFG 0x21D00 +#define CONFIG_SYS_CS1_START CONFIG_SYS_SRAM_BASE +#define CONFIG_SYS_CS1_SIZE 0x00200000 +#define CONFIG_SYS_CS1_CFG 0x21D00 /* Display H1, Status Inputs, EPLD @0x80600000 8 Bit */ -#define CFG_CS3_START CFG_DISPLAY_BASE -#define CFG_CS3_SIZE 0x00000100 -#define CFG_CS3_CFG 0x00081802 +#define CONFIG_SYS_CS3_START CONFIG_SYS_DISPLAY_BASE +#define CONFIG_SYS_CS3_SIZE 0x00000100 +#define CONFIG_SYS_CS3_CFG 0x00081802 /* Interbus Master 16 Bit */ -#define CFG_CS6_START CFG_IB_MASTER -#define CFG_CS6_SIZE 0x00010000 -#define CFG_CS6_CFG 0x00FF3500 +#define CONFIG_SYS_CS6_START CONFIG_SYS_IB_MASTER +#define CONFIG_SYS_CS6_SIZE 0x00010000 +#define CONFIG_SYS_CS6_CFG 0x00FF3500 /* Interbus EPLD 8 Bit */ -#define CFG_CS7_START CFG_IB_EPLD -#define CFG_CS7_SIZE 0x00010000 -#define CFG_CS7_CFG 0x00081800 +#define CONFIG_SYS_CS7_START CONFIG_SYS_IB_EPLD +#define CONFIG_SYS_CS7_SIZE 0x00010000 +#define CONFIG_SYS_CS7_CFG 0x00081800 -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 /*----------------------------------------------------------------------- * IDE/ATA stuff Supports IDE harddisk @@ -330,33 +328,33 @@ #undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ #undef CONFIG_IDE_LED /* LED for ide not supported */ -#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ +#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ +#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */ #define CONFIG_IDE_PREINIT 1 -#define CFG_ATA_IDE0_OFFSET 0x0000 +#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CFG_ATA_BASE_ADDR MPC5XXX_ATA +#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA /* Offset for data I/O */ -#define CFG_ATA_DATA_OFFSET (0x0060) +#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* Offset for normal register accesses */ -#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET) +#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /* Offset for alternate registers */ -#define CFG_ATA_ALT_OFFSET (0x005C) +#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* Interval between registers */ -#define CFG_ATA_STRIDE 4 +#define CONFIG_SYS_ATA_STRIDE 4 #define CONFIG_ATAPI 1 /*---------------------------------------------------------------------*/ /* Display addresses */ /*---------------------------------------------------------------------*/ -#define CFG_DISP_CHR_RAM (CFG_DISPLAY_BASE + 0x38) -#define CFG_DISP_CWORD (CFG_DISPLAY_BASE + 0x30) +#define CONFIG_SYS_DISP_CHR_RAM (CONFIG_SYS_DISPLAY_BASE + 0x38) +#define CONFIG_SYS_DISP_CWORD (CONFIG_SYS_DISPLAY_BASE + 0x30) #endif /* __CONFIG_H */ |