summaryrefslogtreecommitdiff
path: root/include/configs/stxssa.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/stxssa.h')
-rw-r--r--include/configs/stxssa.h195
1 files changed, 100 insertions, 95 deletions
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 1978a32..55e2c8d 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -42,20 +42,20 @@
#define CONFIG_CPM2 1 /* has CPM2 */
#define CONFIG_STXSSA 1 /* Silicon Tx GPPP SSA board specific*/
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support*/
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_PCI /* PCI ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support*/
+#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
-#undef CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#undef CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
/* sysclk for MPC85xx
*/
-#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
+#define CONFIG_SYS_CLK_FREQ 33000000 /* most pci cards are 33Mhz */
/* Blinkin' LEDs for Robert :-)
*/
@@ -64,23 +64,23 @@
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#undef CFG_DRAM_TEST /* memory test, takes time */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_END 0x00400000
-/* Localbus connector. There are many options that can be
+/* Localbus connector. There are many options that can be
* connected here, including sdram or lots of flash.
* This address, however, is used to configure a 256M local bus
* window that includes the Config latch below.
*/
-#define CFG_LBC_OPTION_BASE 0xF0000000 /* Localbus Extension */
+#define CFG_LBC_OPTION_BASE 0xF0000000 /* Localbus Extension */
#define CFG_LBC_OPTION_SIZE 256 /* 256MB */
/* There are various flash options used, we configure for the largest,
@@ -88,16 +88,16 @@
* sizes.
*/
#ifdef CONFIG_STXSSA_4M
-#define CFG_FLASH_BASE 0xFFC00000 /* start of 4 MiB flash */
+#define CFG_FLASH_BASE 0xFFC00000 /* start of 4 MiB flash */
#else
-#define CFG_FLASH_BASE 0xFC000000 /* start of 64 MiB flash */
+#define CFG_FLASH_BASE 0xFC000000 /* start of 64 MiB flash */
#endif
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | 0x1801) /* port size 32bit */
#define CFG_OR0_PRELIM (CFG_FLASH_BASE | 0x0FF7)
#define CFG_FLASH_CFI 1
#define CFG_FLASH_CFI_DRIVER 1
-#undef CFG_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
+#undef CFG_FLASH_USE_BUFFER_WRITE /* use buffered writes (20x faster) */
#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
@@ -110,22 +110,22 @@
*/
#define CFG_LBC_CFGLATCH_BASE 0xFB000000 /* Base of config latch */
#define CFG_BR1_PRELIM 0xFB001801 /* 32-bit port */
-#define CFG_OR1_PRELIM 0xFFFF0FF7 /* 64K is enough */
+#define CFG_OR1_PRELIM 0xFFFF0FF7 /* 64K is enough */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#ifdef CFG_RAMBOOT
-#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */
+#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */
#else
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#endif
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
@@ -140,14 +140,14 @@
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */
+#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */
#undef CONFIG_CLOCKS_IN_MHZ
/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
+#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
#define CFG_LBC_LBCR 0x00000000
#define CFG_LBC_LSRT 0x20000000
#define CFG_LBC_MRTPR 0x20000000
@@ -158,52 +158,52 @@
#define CFG_LBC_LSDMR_5 0x4061b723
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 2
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CFG_NS16550
#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
+#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
+#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CFG_HUSH_PARSER 1 /* Use the HUSH parser */
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#if 0
-#define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */
#else
/* I did the 'if 0' so we could keep the syntax above if ever needed. */
#undef CFG_I2C_NOPROBES
#endif
#define CFG_I2C_OFFSET 0x3000
-/* I2C EEPROM. AT24C32, we keep our environment in here.
+/* I2C EEPROM. AT24C32, we keep our environment in here.
*/
#define CFG_I2C_EEPROM_ADDR 0x51 /* 1010001x */
#define CFG_I2C_EEPROM_ADDR_LEN 2
@@ -232,35 +232,35 @@
#if defined(CONFIG_PCI) /* PCI Ethernet card */
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
+#define CONFIG_EEPRO100
+#define CONFIG_TULIP
#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#undef CONFIG_PCI_SCAN_SHOW
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+#define CONFIG_PCI_SCAN_SHOW
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC85XX_TSEC1 1
-#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPS85XX_FEC
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define CONFIG_MPS85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 4
@@ -270,9 +270,9 @@
#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
+#define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
#if (CONFIG_ETHER_INDEX == 2)
/*
@@ -281,19 +281,19 @@
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
+ #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CFG_CPMFCR_RAMTYPE 0
#if 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
+ #define CFG_FCC_PSMR (FCC_PSMR_FDE)
#else
- #define CFG_FCC_PSMR 0
+ #define CFG_FCC_PSMR 0
#endif
#define FETH2_RST 0x01
#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
-#endif /* CONFIG_ETHER_INDEX */
+#endif /* CONFIG_ETHER_INDEX */
/* MDIO is done through the TSEC0 control.
*/
@@ -325,34 +325,39 @@
#define CONFIG_TIMESTAMP /* Print image info with ts */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+ #define CONFIG_CMD_MII
+#endif
+
#if defined(CFG_RAMBOOT)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
- #elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_MII | CFG_CMD_I2C ) & \
- ~(CFG_CMD_ENV))
- #elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV))
- #endif
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
- #elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C)
- #elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C)
- #endif
+ #define CONFIG_CMD_ELF
#endif
-#include <cmd_confdefs.h>
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -361,7 +366,7 @@
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "SSA=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -382,7 +387,7 @@
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
@@ -394,7 +399,7 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
@@ -415,13 +420,13 @@
*/
#ifdef CFG_ENV_IS_IN_EEPROM /* use restricted "standard" environment */
-#define CONFIG_BAUDRATE 38400
+#define CONFIG_BAUDRATE 38400
#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_BOOTCOMMAND "bootm 0xffc00000 0xffd00000"
#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,$baudrate"
#define CONFIG_SERVERIP 192.168.85.1
-#define CONFIG_IPADDR 192.168.85.60
+#define CONFIG_IPADDR 192.168.85.60
#define CONFIG_GATEWAYIP 192.168.85.1
#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_HOSTNAME STX_SSA
@@ -431,7 +436,7 @@
#else /* ENV IS IN FLASH -- use a full-blown envionment */
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */