diff options
Diffstat (limited to 'include/configs/stxgp3.h')
| -rw-r--r-- | include/configs/stxgp3.h | 196 |
1 files changed, 89 insertions, 107 deletions
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index 8460944..f5b4836 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -39,7 +39,6 @@ #define CONFIG_BOOKE 1 /* BOOKE */ #define CONFIG_E500 1 /* BOOKE e500 family */ #define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */ -#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */ #define CONFIG_MPC8560 1 /* MPC8560 specific */ #define CONFIG_STXGP3 1 /* Silicon Tx GPPP board specific*/ @@ -49,15 +48,12 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ #undef CONFIG_DDR_ECC /* only for ECC DDR module */ - -#if defined(CONFIG_MPC85xx_REV1) #define CONFIG_DDR_DLL /* possible DLL fix needed */ -#endif +#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */ + -/* Using Localbus SDRAM to emulate flash before we can program the flash, - * normally you need a flash-boot image(u-boot.bin), if so undef this. +/* sysclk for MPC85xx */ -#undef CONFIG_RAM_AS_FLASH #define CONFIG_SYS_CLK_FREQ 33333333 /* most pci cards are 33Mhz */ @@ -65,55 +61,29 @@ */ #define CONFIG_SHOW_ACTIVITY 1 -#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */ -#define CONFIG_DDR_SETTING -#endif - -/* below can be toggled for performance analysis. otherwise use default */ +/* + * These can be toggled for performance analysis, otherwise use default. + */ #define CONFIG_L2_CACHE /* toggle L2 cache */ -#undef CONFIG_BTB /* toggle branch predition */ -#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ -#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */ +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #undef CFG_DRAM_TEST /* memory test, takes time */ #define CFG_MEMTEST_START 0x00200000 /* memtest region */ #define CFG_MEMTEST_END 0x00400000 -#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \ - defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \ - defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC)) -#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC." -#endif - -/* - * Base addresses -- Note these are effective addresses where the - * actual resources get mapped (not physical addresses) - */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE - -/* GPPP supports up to 2G of DRAM. Allocate up to 1G until we get - * a chance to try it out. Actual size is always read from sdram eeprom. - */ -#define CFG_SDRAM_SIZE 1024 /* DDR is 1GB */ /* Localbus SDRAM is an option, not all boards have it. -*/ -#if defined(CONFIG_RAM_AS_FLASH) -#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */ -#else -#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */ -#endif -#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */ + * This address, however, is used to configure a 256M local bus + * window that includes the Config latch below. + */ +#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CFG_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ -#if defined(CONFIG_RAM_AS_FLASH) -#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */ -#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */ -#else /* Boot from real Flash */ #define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ #define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ -#endif #define CFG_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ #define CFG_MAX_FLASH_BANKS 1 /* number of banks */ @@ -123,7 +93,7 @@ #define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* The configuration latch is Chip Select 1. - * It's an 8-bit latch in the upper 8 bits of the word. + * It's an 8-bit latch in the lower 8 bits of the word. */ #define CFG_BR1_PRELIM 0xfc001801 /* 32-bit port */ #define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ @@ -146,17 +116,18 @@ #define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ -#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ +/* + * DDR Setup + */ -#if defined(CONFIG_DDR_SETTING) -#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */ -#define CFG_DDR_CS0_CONFIG 0x80000002 -#define CFG_DDR_TIMING_1 0x37344321 -#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/ -#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/ -#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */ -#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/ -#endif +/* + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + */ +#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE + +#define SPD_EEPROM_ADDRESS 0x54 /* DDR DIMM */ #undef CONFIG_CLOCKS_IN_MHZ @@ -213,37 +184,65 @@ #undef CFG_I2C_NOPROBES #endif -#define CFG_PCI_MEM_BASE 0xe0000000 -#define CFG_PCI_MEM_PHYS 0xe0000000 -#define CFG_PCI_MEM_SIZE 0x10000000 +/* RapdIO Map configuration, mapped 1:1. +*/ +#define CFG_RIO_MEM_BASE 0xc0000000 +#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE +#define CFG_RIO_MEM_SIZE 0x200000000 /* 512 M */ + +/* Standard 8560 PCI addressing, mapped 1:1. +*/ +#define CFG_PCI1_MEM_BASE 0x80000000 +#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE +#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CFG_PCI1_IO_BASE 0xe2000000 +#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE +#define CFG_PCI1_IO_SIZE 0x01000000 /* 16 M */ #if defined(CONFIG_PCI) /* PCI Ethernet card */ + #define CONFIG_NET_MULTI -#define CONFIG_EEPRO100 -#undef CONFIG_TULIP #define CONFIG_PCI_PNP /* do pci plug-and-play */ - #if !defined(CONFIG_PCI_PNP) + +#undef CONFIG_EEPRO100 +#undef CONFIG_TULIP + +#if !defined(CONFIG_PCI_PNP) #define PCI_ENET0_IOADDR 0xe0000000 #define PCI_ENET0_MEMADDR 0xe0000000 #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */ - #endif -#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ -#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */ - #define CFG_PCI_SUBSYS_DEVICEID 0x0003 -#else - #define CFG_PCI_SUBSYS_DEVICEID 0x0009 #endif -#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */ + +#undef CONFIG_PCI_SCAN_SHOW +#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ + +#endif /* CONFIG_PCI */ + +#if defined(CONFIG_TSEC_ENET) + +#ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 -#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */ +#endif + #define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_PHY_ADDR 8 /* PHY address */ + +#define CONFIG_MPC85XX_TSEC1 1 +#define CONFIG_MPC85XX_TSEC2 1 +#undef CONFIG_MPS85XX_FEC + +#define TSEC1_PHY_ADDR 2 +#define TSEC2_PHY_ADDR 4 +#define TSEC1_PHYIDX 0 +#define TSEC2_PHYIDX 0 +#define CONFIG_ETHPRIME "MOTO ENET0" + #elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */ + #define CONFIG_ETHER_ON_FCC2 /* define if ether on FCC */ #undef CONFIG_ETHER_NONE /* define if ether on something else */ #define CONFIG_ETHER_INDEX 2 /* which channel for ether */ - #if (CONFIG_ETHER_INDEX == 2) + +#if (CONFIG_ETHER_INDEX == 2) /* * - Rx-CLK is CLK13 * - Tx-CLK is CLK14 @@ -259,59 +258,41 @@ #define CFG_FCC_PSMR 0 #endif #define FETH2_RST 0x01 - #elif (CONFIG_ETHER_INDEX == 3) +#elif (CONFIG_ETHER_INDEX == 3) /* need more definitions here for FE3 */ #define FETH3_RST 0x80 - #endif /* CONFIG_ETHER_INDEX */ +#endif /* CONFIG_ETHER_INDEX */ + +/* MDIO is done through the TSEC0 control. +*/ #define CONFIG_MII /* MII PHY management */ #undef CONFIG_BITBANGMII /* bit-bang MII PHY management */ -/* - * GPIO pins used for bit-banged MII communications - */ -#define MDIO_PORT 2 /* Port C */ -#define MDIO_ACTIVE (iop->pdir |= 0x00400000) -#define MDIO_TRISTATE (iop->pdir &= ~0x00400000) -#define MDIO_READ ((iop->pdat & 0x00400000) != 0) - -#define MDIO(bit) if(bit) iop->pdat |= 0x00400000; \ - else iop->pdat &= ~0x00400000 -#define MDC(bit) if(bit) iop->pdat |= 0x00200000; \ - else iop->pdat &= ~0x00200000 - -#define MIIDELAY udelay(1) #endif /* Environment */ /* We use the top boot sector flash, so we have some 16K sectors for env - * But....functions don't seem smart enough yet. */ #ifndef CFG_RAMBOOT - #if defined(CONFIG_RAM_AS_FLASH) - #define CFG_ENV_IS_NOWHERE - #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000) - #define CFG_ENV_SIZE 0x2000 - #else #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000) #define CFG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ - #endif #define CFG_ENV_SIZE 0x2000 #else -#define CFG_NO_FLASH 1 /* Flash is not usable now */ -#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ -#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) -#define CFG_ENV_SIZE 0x2000 + #define CFG_NO_FLASH 1 /* Flash is not usable now */ + #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) + #define CFG_ENV_SIZE 0x2000 #endif #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" -#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xff900000" +#define CONFIG_BOOTCOMMAND "bootm 0xff000000 0xff100000" #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ #define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ -#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH) +#if defined(CFG_RAMBOOT) #if defined(CONFIG_PCI) #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \ CFG_CMD_PING | CFG_CMD_I2C) & \ @@ -329,13 +310,13 @@ #else #if defined(CONFIG_PCI) #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \ - CFG_CMD_PING | CFG_CMD_I2C) + CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) #elif defined(CONFIG_TSEC_ENET) #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \ - CFG_CMD_MII | CFG_CMD_I2C) + CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_I2C) #elif defined(CONFIG_ETHER_ON_FCC) #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \ - CFG_CMD_PING | CFG_CMD_I2C) + CFG_CMD_ELF | CFG_CMD_PING | CFG_CMD_I2C) #endif #endif #include <cmd_confdefs.h> @@ -387,9 +368,9 @@ /*Note: change below for your network setting!!! */ #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC) -#define CONFIG_ETHADDR 00:01:af:07:9b:8a -#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b -#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c +#define CONFIG_ETHADDR 00:e0:0c:07:9b:8a +#define CONFIG_ETH1ADDR 00:e0:0c:07:9b:8b +#define CONFIG_ETH2ADDR 00:e0:0c:07:9b:8c #endif #define CONFIG_SERVERIP 192.168.85.1 @@ -399,5 +380,6 @@ #define CONFIG_HOSTNAME STX_GP3 #define CONFIG_ROOTPATH /gppproot #define CONFIG_BOOTFILE uImage +#define CONFIG_LOADADDR 0x1000000 #endif /* __CONFIG_H */ |