diff options
Diffstat (limited to 'include/configs/stxgp3.h')
| -rw-r--r-- | include/configs/stxgp3.h | 192 |
1 files changed, 95 insertions, 97 deletions
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h index ea79de7..ae6f45a 100644 --- a/include/configs/stxgp3.h +++ b/include/configs/stxgp3.h @@ -64,55 +64,54 @@ */ #define CONFIG_L2_CACHE /* toggle L2 cache */ #define CONFIG_BTB /* toggle branch predition */ -#define CONFIG_ADDR_STREAMING /* toggle addr streaming */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00200000 /* memtest region */ -#define CFG_MEMTEST_END 0x00400000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 /* Localbus SDRAM is an option, not all boards have it. * This address, however, is used to configure a 256M local bus * window that includes the Config latch below. */ -#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ -#define CFG_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ +#define CONFIG_SYS_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */ +#define CONFIG_SYS_LBC_SDRAM_SIZE 256 /* LBC SDRAM is 64MB */ -#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ -#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */ +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ +#define CONFIG_SYS_BR0_PRELIM 0xff001801 /* port size 32bit */ -#define CFG_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 136 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_OR0_PRELIM 0xff000ff7 /* 16 MB Flash */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 136 /* sectors per device */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ /* The configuration latch is Chip Select 1. * It's an 8-bit latch in the lower 8 bits of the word. */ -#define CFG_BR1_PRELIM 0xfc001801 /* 32-bit port */ -#define CFG_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ -#define CFG_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ +#define CONFIG_SYS_BR1_PRELIM 0xfc001801 /* 32-bit port */ +#define CONFIG_SYS_OR1_PRELIM 0xffff0ff7 /* 64K is enough */ +#define CONFIG_SYS_LBC_LCLDEVS_BASE 0xfc000000 /* Base of localbus devices */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #else -#undef CFG_RAMBOOT +#undef CONFIG_SYS_RAMBOOT #endif -#ifdef CFG_RAMBOOT -#define CFG_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ +#ifdef CONFIG_SYS_RAMBOOT +#define CONFIG_SYS_CCSRBAR_DEFAULT 0x40000000 /* CCSRBAR by BDI cfg */ #else -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ #endif -#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ -#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */ +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ /* DDR Setup */ #define CONFIG_FSL_DDR1 @@ -126,8 +125,8 @@ #define CONFIG_MEM_INIT_VALUE 0xDeadBeef -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_NUM_DDR_CONTROLLERS 1 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 @@ -139,29 +138,28 @@ #undef CONFIG_CLOCKS_IN_MHZ /* local bus definitions */ -#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ -#define CFG_OR2_PRELIM 0xfc006901 -#define CFG_LBC_LCRR 0x00030004 /* local bus freq */ -#define CFG_LBC_LBCR 0x00000000 -#define CFG_LBC_LSRT 0x20000000 -#define CFG_LBC_MRTPR 0x20000000 -#define CFG_LBC_LSDMR_1 0x2861b723 -#define CFG_LBC_LSDMR_2 0x0861b723 -#define CFG_LBC_LSDMR_3 0x0861b723 -#define CFG_LBC_LSDMR_4 0x1861b723 -#define CFG_LBC_LSDMR_5 0x4061b723 - -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#define CFG_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ - -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */ +#define CONFIG_SYS_OR2_PRELIM 0xfc006901 +#define CONFIG_SYS_LBC_LCRR 0x00030004 /* local bus freq */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LBC_LSRT 0x20000000 +#define CONFIG_SYS_LBC_MRTPR 0x20000000 +#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723 +#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723 +#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723 +#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723 + +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#define CONFIG_SYS_INIT_RAM_ADDR 0x60000000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ + +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_ON_SCC /* define if console on SCC */ @@ -170,13 +168,13 @@ #define CONFIG_BAUDRATE 38400 -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* @@ -185,30 +183,30 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F #if 0 -#define CFG_I2C_NOPROBES {0x00} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_NOPROBES {0x00} /* Don't probe these addrs */ #else /* I did the 'if 0' so we could keep the syntax above if ever needed. */ -#undef CFG_I2C_NOPROBES +#undef CONFIG_SYS_I2C_NOPROBES #endif -#define CFG_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C_OFFSET 0x3000 /* RapdIO Map configuration, mapped 1:1. */ -#define CFG_RIO_MEM_BASE 0xc0000000 -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x200000000 /* 512 M */ +#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 +#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE +#define CONFIG_SYS_RIO_MEM_SIZE 0x200000000 /* 512 M */ /* Standard 8560 PCI addressing, mapped 1:1. */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x01000000 /* 16 M */ +#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BASE 0xe2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BASE +#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000 /* 16 M */ #if defined(CONFIG_PCI) /* PCI Ethernet card */ @@ -225,7 +223,7 @@ #endif #undef CONFIG_PCI_SCAN_SHOW -#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */ #endif /* CONFIG_PCI */ @@ -263,13 +261,13 @@ * - Select bus for bd/buffers * - Full duplex */ - #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) - #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - #define CFG_CPMFCR_RAMTYPE 0 + #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) + #define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) + #define CONFIG_SYS_CPMFCR_RAMTYPE 0 #if 0 - #define CFG_FCC_PSMR (FCC_PSMR_FDE) + #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE) #else - #define CFG_FCC_PSMR 0 + #define CONFIG_SYS_FCC_PSMR 0 #endif #define FETH2_RST 0x01 #elif (CONFIG_ETHER_INDEX == 3) @@ -287,16 +285,16 @@ /* Environment */ /* We use the top boot sector flash, so we have some 16K sectors for env */ -#ifndef CFG_RAMBOOT - #define CFG_ENV_IS_IN_FLASH 1 - #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000) - #define CFG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ - #define CFG_ENV_SIZE 0x2000 +#ifndef CONFIG_SYS_RAMBOOT + #define CONFIG_ENV_IS_IN_FLASH 1 + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000) + #define CONFIG_ENV_SECT_SIZE 0x4000 /* 16K (one top sector) for env */ + #define CONFIG_ENV_SIZE 0x2000 #else - #define CFG_NO_FLASH 1 /* Flash is not usable now */ - #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ - #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000) - #define CFG_ENV_SIZE 0x2000 + #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ + #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ + #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) + #define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_BOOTARGS "root=/dev/nfs rw ip=any console=ttyS1,38400" @@ -304,7 +302,7 @@ #define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /* * BOOTP options @@ -323,7 +321,7 @@ #define CONFIG_CMD_PING #define CONFIG_CMD_I2C -#if defined(CFG_RAMBOOT) +#if defined(CONFIG_SYS_RAMBOOT) #undef CONFIG_CMD_ENV #undef CONFIG_CMD_LOADS #else @@ -344,25 +342,25 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "GPPP=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "GPPP=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_LOAD_ADDR 0x1000000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions |