diff options
Diffstat (limited to 'include/configs/sequoia.h')
| -rw-r--r-- | include/configs/sequoia.h | 225 |
1 files changed, 112 insertions, 113 deletions
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h index d39a894..9321bdc 100644 --- a/include/configs/sequoia.h +++ b/include/configs/sequoia.h @@ -48,7 +48,7 @@ #include "amcc-common.h" /* Detect Sequoia PLL input clock automatically via CPLD bit */ -#define CONFIG_SYS_CLK_FREQ ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \ +#define CONFIG_SYS_CLK_FREQ ((in8(CONFIG_SYS_BCSR_BASE + 3) & 0x80) ? \ 33333333 : 33000000) /* @@ -72,40 +72,40 @@ * Base addresses -- Note these are effective addresses where the actual * resources get mapped (not physical addresses). */ -#define CFG_TLB_FOR_BOOT_FLASH 0x0003 -#define CFG_BOOT_BASE_ADDR 0xf0000000 -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_NAND_ADDR 0xd0000000 /* NAND Flash */ -#define CFG_OCM_BASE 0xe0010000 /* ocm */ -#define CFG_OCM_DATA_ADDR CFG_OCM_BASE -#define CFG_PCI_BASE 0xe0000000 /* Internal PCI regs */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 +#define CONFIG_SYS_TLB_FOR_BOOT_FLASH 0x0003 +#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000 +#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CONFIG_SYS_NAND_ADDR 0xd0000000 /* NAND Flash */ +#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */ +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_OCM_BASE +#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 /* Don't change either of these */ -#define CFG_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* internal peripherals */ -#define CFG_USB2D0_BASE 0xe0000100 -#define CFG_USB_DEVICE 0xe0000000 -#define CFG_USB_HOST 0xe0000400 -#define CFG_BCSR_BASE 0xc0000000 +#define CONFIG_SYS_USB2D0_BASE 0xe0000100 +#define CONFIG_SYS_USB_DEVICE 0xe0000000 +#define CONFIG_SYS_USB_HOST 0xe0000400 +#define CONFIG_SYS_BCSR_BASE 0xc0000000 /* * Initial RAM & stack pointer */ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ -#define CFG_INIT_RAM_END (4 << 10) -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */ +#define CONFIG_SYS_INIT_RAM_END (4 << 10) +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR /* * Serial Port */ -#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE @@ -122,26 +122,26 @@ /* * FLASH related */ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_PROTECTION 1 /* use hardware flash protection */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR ((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -167,75 +167,74 @@ * set up. While still running from cache, I experienced problems accessing * the NAND controller. sr - 2006-08-25 */ -#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CFG_NAND_BOOT_SPL_DST (CFG_OCM_BASE + (12 << 10)) /* Copy SPL here */ -#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from */ +#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CONFIG_SYS_NAND_BOOT_SPL_DST (CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from */ /* this addr */ -#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) +#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) /* * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) */ -#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CFG_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#undef CFG_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ - -#define CFG_NAND_ECCSIZE 256 -#define CFG_NAND_ECCBYTES 3 -#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) -#define CFG_NAND_OOBSIZE 16 -#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) -#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} +#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#undef CONFIG_SYS_NAND_4_ADDR_CYCLE /* No fourth addr used (<=32MB) */ + +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 16 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS) +#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} #ifdef CONFIG_ENV_IS_IN_NAND /* * For NAND booting the environment is embedded in the U-Boot image. Please take * look at the file board/amcc/sequoia/u-boot-nand.lds for details. */ -#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #endif /* * DDR SDRAM */ -#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) #define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */ #endif -#define CFG_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ +#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */ /* 440EPx errata CHIP 11 */ /* * I2C */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 +#define CONFIG_SYS_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_EEPROM_ADDR (0xa8>>1) +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_AD7414 1 /* use AD7414 */ #define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 /* * Default environment variables @@ -265,13 +264,13 @@ #ifdef CONFIG_440EPX #define CONFIG_USB_OHCI_NEW #define CONFIG_USB_STORAGE -#define CFG_OHCI_BE_CONTROLLER +#define CONFIG_SYS_OHCI_BE_CONTROLLER -#undef CFG_USB_OHCI_BOARD_INIT -#define CFG_USB_OHCI_CPU_INIT 1 -#define CFG_USB_OHCI_REGS_BASE CFG_USB_HOST -#define CFG_USB_OHCI_SLOT_NAME "ppc440" -#define CFG_USB_OHCI_MAX_ROOT_PORTS 15 +#undef CONFIG_SYS_USB_OHCI_BOARD_INIT +#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 +#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST +#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ppc440" +#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 /* Comment this out to enable USB 1.1 device */ #define USB_2_0_DEVICE @@ -297,26 +296,26 @@ #endif #ifndef CONFIG_RAINIER -#define CFG_POST_FPU_ON CFG_POST_FPU +#define CONFIG_SYS_POST_FPU_ON CONFIG_SYS_POST_FPU #else -#define CFG_POST_FPU_ON 0 +#define CONFIG_SYS_POST_FPU_ON 0 #endif /* POST support */ -#define CONFIG_POST (CFG_POST_CACHE | \ - CFG_POST_CPU | \ - CFG_POST_ETHER | \ - CFG_POST_FPU_ON | \ - CFG_POST_I2C | \ - CFG_POST_MEMORY | \ - CFG_POST_SPR | \ - CFG_POST_UART) - -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_FPU_ON | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_SPR | \ + CONFIG_SYS_POST_UART) + +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) #define CONFIG_LOGBUFFER -#define CFG_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ +#define CONFIG_SYS_POST_CACHE_ADDR 0x7fff0000 /* free virtual address */ -#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ #define CONFIG_SUPPORT_VFAT @@ -326,16 +325,16 @@ /* General PCI */ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ -#define CFG_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ +#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 0 /* to avoid problems with PNP */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ - /* CFG_PCI_MEMBASE */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to */ + /* CONFIG_SYS_PCI_MEMBASE */ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT -#define CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT +#define CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_ID 0xcafe /* Whatever */ /* * External Bus Controller (EBC) Setup @@ -345,44 +344,44 @@ * On Sequoia CS0 and CS3 are switched when configuring for NAND booting */ #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) -#define CFG_NAND_CS 3 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 3 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x03017200 -#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000) +#define CONFIG_SYS_EBC_PB0AP 0x03017200 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000) /* Memory Bank 3 (NAND-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x018003c0 -#define CFG_EBC_PB3CR (CFG_NAND_ADDR | 0x1c000) +#define CONFIG_SYS_EBC_PB3AP 0x018003c0 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND_ADDR | 0x1c000) #else -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ /* Memory Bank 3 (NOR-FLASH) initialization */ -#define CFG_EBC_PB3AP 0x03017200 -#define CFG_EBC_PB3CR (CFG_FLASH_BASE | 0xda000) +#define CONFIG_SYS_EBC_PB3AP 0x03017200 +#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH_BASE | 0xda000) /* Memory Bank 0 (NAND-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x018003c0 -#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1c000) +#define CONFIG_SYS_EBC_PB0AP 0x018003c0 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1c000) #endif /* Memory Bank 2 (CPLD) initialization */ -#define CFG_EBC_PB2AP 0x24814580 -#define CFG_EBC_PB2CR (CFG_BCSR_BASE | 0x38000) +#define CONFIG_SYS_EBC_PB2AP 0x24814580 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_BCSR_BASE | 0x38000) -#define CFG_BCSR5_PCI66EN 0x80 +#define CONFIG_SYS_BCSR5_PCI66EN 0x80 /* * NAND FLASH */ -#define CFG_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ /* * PPC440 GPIO Configuration */ /* test-only: take GPIO init from pcs440ep ???? in config file */ -#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_BI , GPIO_ALT1, GPIO_OUT_0}, /* GPIO0 EBC_ADDR(7) DMA_REQ(2) */ \ @@ -459,7 +458,7 @@ #define CONFIG_BIOSEMU /* x86 bios emulator for vga bios */ #define CONFIG_ATI_RADEON_FB /* use radeon framebuffer driver */ #define VIDEO_IO_OFFSET 0xe8000000 -#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET +#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET #define CONFIG_VIDEO_SW_CURSOR #define CONFIG_VIDEO_LOGO #define CONFIG_CFB_CONSOLE |