diff options
Diffstat (limited to 'include/configs/sc3.h')
| -rw-r--r-- | include/configs/sc3.h | 65 |
1 files changed, 38 insertions, 27 deletions
diff --git a/include/configs/sc3.h b/include/configs/sc3.h index 6b6acfa..cb22536 100644 --- a/include/configs/sc3.h +++ b/include/configs/sc3.h @@ -58,7 +58,7 @@ * 0xFFE00000 .... 0xFFFFFFFF -> BOOT-ROM (2 MiB) */ -#define CONFIG_SOLIDCARD3 1 +#define CONFIG_SC3 1 #define CONFIG_4xx 1 #define CONFIG_405GP 1 @@ -68,8 +68,7 @@ * Define IDE_USES_ISA_EMULATION for slower IDE access in the ISA-IO address range * If undefined, IDE access uses a seperat emulation with higher access speed. * Consider to inform your Linux IDE driver about the different addresses! - * IDE_USES_ISA_EMULATION is only used if your CONFIG_COMMANDS macro includes - * the CFG_CMD_IDE macro! + * IDE_USES_ISA_EMULATION is only used if you define CONFIG_CMD_IDE! */ #define IDE_USES_ISA_EMULATION @@ -134,7 +133,8 @@ #if 1 /* feel free to disable for development */ #define CONFIG_AUTOBOOT_KEYED /* Enable password protection */ #define CONFIG_AUTOBOOT_PROMPT "\nSC3 - booting... stop with ENTER\n" -#define CONFIG_AUTOBOOT_DELAY_STR "\n" /* 1st "password" */ +#define CONFIG_AUTOBOOT_DELAY_STR "\r" /* 1st "password" */ +#define CONFIG_AUTOBOOT_DELAY_STR2 "\n" /* 1st "password" */ #endif /* @@ -168,25 +168,36 @@ #define CONFIG_MII 1 /* add 405GP MII PHY management */ #define CONFIG_PHY_ADDR 1 /* the connected Phy defaults to address 1 */ -#define CONFIG_COMMANDS \ - (CONFIG_CMD_DFL | \ - CFG_CMD_AUTOSCRIPT | \ - CFG_CMD_PCI | \ - CFG_CMD_IRQ | \ - CFG_CMD_NET | \ - CFG_CMD_MII | \ - CFG_CMD_PING | \ - CFG_CMD_NAND | \ - CFG_CMD_JFFS2 | \ - CFG_CMD_I2C | \ - CFG_CMD_IDE | \ - CFG_CMD_DATE | \ - CFG_CMD_DHCP | \ - CFG_CMD_CACHE | \ - CFG_CMD_ELF ) - -/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ -#include <cmd_confdefs.h> +/* + * BOOTP options + */ +#define CONFIG_BOOTP_BOOTFILESIZE +#define CONFIG_BOOTP_BOOTPATH +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_HOSTNAME + + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + + +#define CONFIG_CMD_AUTOSCRIPT +#define CONFIG_CMD_PCI +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_NET +#define CONFIG_CMD_MII +#define CONFIG_CMD_PING +#define CONFIG_CMD_NAND +#define CONFIG_CMD_JFFS2 +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IDE +#define CONFIG_CMD_DATE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_ELF + #undef CONFIG_WATCHDOG /* watchdog disabled */ @@ -276,7 +287,7 @@ * External peripheral base address *----------------------------------------------------------------------- */ -#if !(CONFIG_COMMANDS & CFG_CMD_IDE) +#if !defined(CONFIG_CMD_IDE) #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ @@ -285,7 +296,7 @@ * IDE/ATA stuff *----------------------------------------------------------------------- */ -#else /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */ +#else #define CONFIG_START_IDE 1 /* check, if use IDE */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ @@ -345,7 +356,7 @@ #endif /* IDE_USES_ISA_EMULATION */ -#endif /* !(CONFIG_COMMANDS & CFG_CMD_IDE) */ +#endif /* #define CFG_KEY_REG_BASE_ADDR 0xF0100000 @@ -436,7 +447,7 @@ extern unsigned long offsetOfEnvironment; #define CFG_CACHELINE_SIZE 32 -#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#if defined(CONFIG_CMD_KGDB) #define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif |