diff options
Diffstat (limited to 'include/configs/sbc8641d.h')
| -rw-r--r-- | include/configs/sbc8641d.h | 406 |
1 files changed, 217 insertions, 189 deletions
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h index 01003a3..1008812 100644 --- a/include/configs/sbc8641d.h +++ b/include/configs/sbc8641d.h @@ -44,10 +44,16 @@ #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ #ifdef RUN_DIAG -#define CFG_DIAG_ADDR 0xff800000 +#define CONFIG_SYS_DIAG_ADDR 0xff800000 #endif -#define CFG_RESET_ADDRESS 0xfff00100 +#define CONFIG_SYS_RESET_ADDRESS 0xfff00100 + +/* + * virtual address to be used for temporary mappings. There + * should be 128k free at this VA. + */ +#define CONFIG_SYS_SCRATCH_VA 0xe8000000 #define CONFIG_PCI 1 /* Enable PCIE */ #define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */ @@ -76,7 +82,7 @@ /* * L2CR setup -- make sure this is right for your board! */ -#define CFG_L2 +#define CONFIG_SYS_L2 #define L2_INIT 0 #define L2_ENABLE (L2CR_L2E) @@ -86,28 +92,32 @@ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ -#undef CFG_DRAM_TEST /* memory test, takes time */ -#define CFG_MEMTEST_START 0x00200000 /* memtest region */ -#define CFG_MEMTEST_END 0x00400000 +#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ +#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ +#define CONFIG_SYS_MEMTEST_END 0x00400000 /* * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) */ -#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ -#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ -#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */ +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */ +#define CONFIG_SYS_CCSRBAR 0xf8000000 /* relocated CCSRBAR */ +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ -#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000) -#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000) +#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR +#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0 + +#define CONFIG_SYS_PCI1_ADDR (CONFIG_SYS_CCSRBAR+0x8000) +#define CONFIG_SYS_PCI2_ADDR (CONFIG_SYS_CCSRBAR+0x9000) /* * DDR Setup */ -#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ -#define CFG_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */ -#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE -#define CFG_SDRAM_BASE2 CFG_DDR_SDRAM_BASE2 +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */ +#define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */ +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE +#define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2 +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ #define CONFIG_VERY_BIG_RAM #define MPC86xx_DDR_SDRAM_CLK_CNTL @@ -130,51 +140,51 @@ * Manually set up DDR1 & DDR2 parameters */ - #define CFG_SDRAM_SIZE 512 /* DDR is 512MB */ - - #define CFG_DDR_CS0_BNDS 0x0000000F - #define CFG_DDR_CS1_BNDS 0x00000000 - #define CFG_DDR_CS2_BNDS 0x00000000 - #define CFG_DDR_CS3_BNDS 0x00000000 - #define CFG_DDR_CS0_CONFIG 0x80010102 - #define CFG_DDR_CS1_CONFIG 0x00000000 - #define CFG_DDR_CS2_CONFIG 0x00000000 - #define CFG_DDR_CS3_CONFIG 0x00000000 - #define CFG_DDR_TIMING_3 0x00000000 - #define CFG_DDR_TIMING_0 0x00220802 - #define CFG_DDR_TIMING_1 0x38377322 - #define CFG_DDR_TIMING_2 0x002040c7 - #define CFG_DDR_CFG_1A 0x43008008 - #define CFG_DDR_CFG_2 0x24401000 - #define CFG_DDR_MODE_1 0x23c00542 - #define CFG_DDR_MODE_2 0x00000000 - #define CFG_DDR_MODE_CTL 0x00000000 - #define CFG_DDR_INTERVAL 0x05080100 - #define CFG_DDR_DATA_INIT 0x00000000 - #define CFG_DDR_CLK_CTRL 0x03800000 - #define CFG_DDR_CFG_1B 0xC3008008 - - #define CFG_DDR2_CS0_BNDS 0x0010001F - #define CFG_DDR2_CS1_BNDS 0x00000000 - #define CFG_DDR2_CS2_BNDS 0x00000000 - #define CFG_DDR2_CS3_BNDS 0x00000000 - #define CFG_DDR2_CS0_CONFIG 0x80010102 - #define CFG_DDR2_CS1_CONFIG 0x00000000 - #define CFG_DDR2_CS2_CONFIG 0x00000000 - #define CFG_DDR2_CS3_CONFIG 0x00000000 - #define CFG_DDR2_EXT_REFRESH 0x00000000 - #define CFG_DDR2_TIMING_0 0x00220802 - #define CFG_DDR2_TIMING_1 0x38377322 - #define CFG_DDR2_TIMING_2 0x002040c7 - #define CFG_DDR2_CFG_1A 0x43008008 - #define CFG_DDR2_CFG_2 0x24401000 - #define CFG_DDR2_MODE_1 0x23c00542 - #define CFG_DDR2_MODE_2 0x00000000 - #define CFG_DDR2_MODE_CTL 0x00000000 - #define CFG_DDR2_INTERVAL 0x05080100 - #define CFG_DDR2_DATA_INIT 0x00000000 - #define CFG_DDR2_CLK_CTRL 0x03800000 - #define CFG_DDR2_CFG_1B 0xC3008008 + #define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */ + + #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F + #define CONFIG_SYS_DDR_CS1_BNDS 0x00000000 + #define CONFIG_SYS_DDR_CS2_BNDS 0x00000000 + #define CONFIG_SYS_DDR_CS3_BNDS 0x00000000 + #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 + #define CONFIG_SYS_DDR_CS1_CONFIG 0x00000000 + #define CONFIG_SYS_DDR_CS2_CONFIG 0x00000000 + #define CONFIG_SYS_DDR_CS3_CONFIG 0x00000000 + #define CONFIG_SYS_DDR_TIMING_3 0x00000000 + #define CONFIG_SYS_DDR_TIMING_0 0x00220802 + #define CONFIG_SYS_DDR_TIMING_1 0x38377322 + #define CONFIG_SYS_DDR_TIMING_2 0x002040c7 + #define CONFIG_SYS_DDR_CFG_1A 0x43008008 + #define CONFIG_SYS_DDR_CFG_2 0x24401000 + #define CONFIG_SYS_DDR_MODE_1 0x23c00542 + #define CONFIG_SYS_DDR_MODE_2 0x00000000 + #define CONFIG_SYS_DDR_MODE_CTL 0x00000000 + #define CONFIG_SYS_DDR_INTERVAL 0x05080100 + #define CONFIG_SYS_DDR_DATA_INIT 0x00000000 + #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 + #define CONFIG_SYS_DDR_CFG_1B 0xC3008008 + + #define CONFIG_SYS_DDR2_CS0_BNDS 0x0010001F + #define CONFIG_SYS_DDR2_CS1_BNDS 0x00000000 + #define CONFIG_SYS_DDR2_CS2_BNDS 0x00000000 + #define CONFIG_SYS_DDR2_CS3_BNDS 0x00000000 + #define CONFIG_SYS_DDR2_CS0_CONFIG 0x80010102 + #define CONFIG_SYS_DDR2_CS1_CONFIG 0x00000000 + #define CONFIG_SYS_DDR2_CS2_CONFIG 0x00000000 + #define CONFIG_SYS_DDR2_CS3_CONFIG 0x00000000 + #define CONFIG_SYS_DDR2_EXT_REFRESH 0x00000000 + #define CONFIG_SYS_DDR2_TIMING_0 0x00220802 + #define CONFIG_SYS_DDR2_TIMING_1 0x38377322 + #define CONFIG_SYS_DDR2_TIMING_2 0x002040c7 + #define CONFIG_SYS_DDR2_CFG_1A 0x43008008 + #define CONFIG_SYS_DDR2_CFG_2 0x24401000 + #define CONFIG_SYS_DDR2_MODE_1 0x23c00542 + #define CONFIG_SYS_DDR2_MODE_2 0x00000000 + #define CONFIG_SYS_DDR2_MODE_CTL 0x00000000 + #define CONFIG_SYS_DDR2_INTERVAL 0x05080100 + #define CONFIG_SYS_DDR2_DATA_INIT 0x00000000 + #define CONFIG_SYS_DDR2_CLK_CTRL 0x03800000 + #define CONFIG_SYS_DDR2_CFG_1B 0xC3008008 #endif @@ -185,88 +195,88 @@ /* * The SBC8641D contains 16MB flash space at ff000000. */ -#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */ +#define CONFIG_SYS_FLASH_BASE 0xff000000 /* start of FLASH 16M */ /* Flash */ -#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */ -#define CFG_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */ +#define CONFIG_SYS_BR0_PRELIM 0xff001001 /* port size 16bit */ +#define CONFIG_SYS_OR0_PRELIM 0xff006e65 /* 16MB Boot Flash area */ /* 64KB EEPROM */ -#define CFG_BR1_PRELIM 0xf0000801 /* port size 16bit */ -#define CFG_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */ +#define CONFIG_SYS_BR1_PRELIM 0xf0000801 /* port size 16bit */ +#define CONFIG_SYS_OR1_PRELIM 0xffff6e65 /* 64K EEPROM area */ /* EPLD - User switches, board id, LEDs */ -#define CFG_BR2_PRELIM 0xf1000801 /* port size 16bit */ -#define CFG_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */ +#define CONFIG_SYS_BR2_PRELIM 0xf1000801 /* port size 16bit */ +#define CONFIG_SYS_OR2_PRELIM 0xfff06e65 /* EPLD (switches, board ID, LEDs) area */ /* Local bus SDRAM 128MB */ -#define CFG_BR3_PRELIM 0xe0001861 /* port size ?bit */ -#define CFG_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */ -#define CFG_BR4_PRELIM 0xe4001861 /* port size ?bit */ -#define CFG_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */ +#define CONFIG_SYS_BR3_PRELIM 0xe0001861 /* port size ?bit */ +#define CONFIG_SYS_OR3_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (1st half) */ +#define CONFIG_SYS_BR4_PRELIM 0xe4001861 /* port size ?bit */ +#define CONFIG_SYS_OR4_PRELIM 0xfc006cc0 /* 128MB local bus SDRAM area (2nd half) */ /* Disk on Chip (DOC) 128MB */ -#define CFG_BR5_PRELIM 0xe8001001 /* port size ?bit */ -#define CFG_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */ +#define CONFIG_SYS_BR5_PRELIM 0xe8001001 /* port size ?bit */ +#define CONFIG_SYS_OR5_PRELIM 0xf8006e65 /* 128MB local bus SDRAM area (2nd half) */ /* LCD */ -#define CFG_BR6_PRELIM 0xf4000801 /* port size ?bit */ -#define CFG_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ +#define CONFIG_SYS_BR6_PRELIM 0xf4000801 /* port size ?bit */ +#define CONFIG_SYS_OR6_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ /* Control logic & misc peripherals */ -#define CFG_BR7_PRELIM 0xf2000801 /* port size ?bit */ -#define CFG_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ +#define CONFIG_SYS_BR7_PRELIM 0xf2000801 /* port size ?bit */ +#define CONFIG_SYS_OR7_PRELIM 0xfff06e65 /* 128MB local bus SDRAM area (2nd half) */ -#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ -#define CFG_MAX_FLASH_SECT 131 /* sectors per device */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 131 /* sectors per device */ -#undef CFG_FLASH_CHECKSUM -#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ -#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */ +#undef CONFIG_SYS_FLASH_CHECKSUM +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */ +#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_CFI -#define CFG_WRITE_SWAPPED_DATA -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_PROTECTION +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_WRITE_SWAPPED_DATA +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_PROTECTION #undef CONFIG_CLOCKS_IN_MHZ -#define CONFIG_L1_INIT_RAM -#define CFG_INIT_RAM_LOCK 1 -#ifndef CFG_INIT_RAM_LOCK -#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_LOCK 1 +#ifndef CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ #else -#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ #endif -#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */ +#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */ /* Serial Port */ #define CONFIG_CONS_INDEX 1 #undef CONFIG_SERIAL_SOFTWARE_FIFO -#define CFG_NS16550 -#define CFG_NS16550_SERIAL -#define CFG_NS16550_REG_SIZE 1 -#define CFG_NS16550_CLK get_bus_freq(0) +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} -#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500) -#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600) +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) /* Use the HUSH parser */ -#define CFG_HUSH_PARSER -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_HUSH_PARSER +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif /* @@ -276,8 +286,8 @@ #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 -#define CFG_64BIT_VSPRINTF 1 -#define CFG_64BIT_STRTOUL 1 +#define CONFIG_SYS_64BIT_VSPRINTF 1 +#define CONFIG_SYS_64BIT_STRTOUL 1 /* * I2C @@ -285,46 +295,45 @@ #define CONFIG_FSL_I2C /* Use FSL common I2C driver */ #define CONFIG_HARD_I2C /* I2C with hardware support*/ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ -#define CFG_I2C_OFFSET 0x3100 +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_OFFSET 0x3100 /* * RapidIO MMU */ -#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */ -#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE -#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */ +#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */ +#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE +#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */ /* * General PCI * Addresses are mapped 1-1. */ -#define CFG_PCI1_MEM_BASE 0x80000000 -#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE -#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */ -#define CFG_PCI1_IO_BASE 0xe2000000 -#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE -#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */ - -/* PCI view of System Memory */ -#define CFG_PCI_MEMORY_BUS 0x00000000 -#define CFG_PCI_MEMORY_PHYS 0x00000000 -#define CFG_PCI_MEMORY_SIZE 0x80000000 - -#define CFG_PCI2_MEM_BASE 0xa0000000 -#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE -#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */ -#define CFG_PCI2_IO_BASE 0xe3000000 -#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE -#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */ +#define CONFIG_SYS_PCI1_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BUS +#define CONFIG_SYS_PCI1_MEM_VIRT CONFIG_SYS_PCI1_MEM_BUS +#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCI1_IO_BUS 0xe2000000 +#define CONFIG_SYS_PCI1_IO_PHYS CONFIG_SYS_PCI1_IO_BUS +#define CONFIG_SYS_PCI1_IO_VIRT CONFIG_SYS_PCI1_IO_BUS +#define CONFIG_SYS_PCI1_IO_SIZE 0x1000000 /* 16M */ + +#define CONFIG_SYS_PCI2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BUS +#define CONFIG_SYS_PCI2_MEM_VIRT CONFIG_SYS_PCI2_MEM_BUS +#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ +#define CONFIG_SYS_PCI2_IO_BUS 0xe3000000 +#define CONFIG_SYS_PCI2_IO_PHYS CONFIG_SYS_PCI2_IO_BUS +#define CONFIG_SYS_PCI2_IO_VIRT CONFIG_SYS_PCI2_IO_BUS +#define CONFIG_SYS_PCI2_IO_SIZE 0x1000000 /* 16M */ #if defined(CONFIG_PCI) #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#undef CFG_SCSI_SCAN_BUS_REVERSE +#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE #define CONFIG_NET_MULTI #define CONFIG_PCI_PNP /* do pci plug-and-play */ @@ -345,10 +354,10 @@ #ifdef CONFIG_SCSI_AHCI #define CONFIG_SATA_ULI5288 -#define CFG_SCSI_MAX_SCSI_ID 4 -#define CFG_SCSI_MAX_LUN 1 -#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN) -#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE +#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 +#define CONFIG_SYS_SCSI_MAX_LUN 1 +#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) +#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE #endif #endif /* CONFIG_PCI */ @@ -383,7 +392,7 @@ #define TSEC3_FLAGS TSEC_GIGABIT #define TSEC4_FLAGS TSEC_GIGABIT -#define CFG_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ +#define CONFIG_SYS_TBIPA_VALUE 0x1e /* Set TBI address not to conflict with TSEC1_PHY_ADDR */ #define CONFIG_ETHPRIME "eTSEC1" @@ -393,10 +402,10 @@ * BAT0 2G Cacheable, non-guarded * 0x0000_0000 2G DDR */ -#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) -#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) -#define CFG_IBAT0U CFG_DBAT0U +#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE ) +#define CONFIG_SYS_IBAT0U CONFIG_SYS_DBAT0U /* * BAT1 1G Cache-inhibited, guarded @@ -404,31 +413,42 @@ * 0xa000_0000 512M PCI-Express 2 Memory * Changed it for operating from 0xd0000000 */ -#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \ +#define CONFIG_SYS_DBAT1L ( CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) -#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT1U CFG_DBAT1U +#define CONFIG_SYS_DBAT1U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_256M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U /* * BAT2 512M Cache-inhibited, guarded * 0xc000_0000 512M RapidIO Memory */ -#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \ +#define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) -#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT2U CFG_DBAT2U +#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U /* * BAT3 4M Cache-inhibited, guarded * 0xf800_0000 4M CCSR */ -#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \ +#define CONFIG_SYS_DBAT3L ( CONFIG_SYS_CCSRBAR | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) -#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT3U CFG_DBAT3U +#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U + +#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) +#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATL_PP_RW | BATL_CACHEINHIBIT \ + | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ + | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU +#endif /* * BAT4 32M Cache-inhibited, guarded @@ -436,46 +456,54 @@ * 0xe300_0000 16M PCI-Express 2 I/0 * Note that this is at 0xe0000000 */ -#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \ +#define CONFIG_SYS_DBAT4L ( CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT) -#define CFG_IBAT4U CFG_DBAT4U +#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT) +#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U /* * BAT5 128K Cacheable, non-guarded * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory) */ -#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) -#define CFG_IBAT5L CFG_DBAT5L -#define CFG_IBAT5U CFG_DBAT5U +#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L +#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U /* * BAT6 32M Cache-inhibited, guarded * 0xfe00_0000 32M FLASH */ -#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ +#define CONFIG_SYS_DBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW \ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) -#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) -#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) -#define CFG_IBAT6U CFG_DBAT6U - -#define CFG_DBAT7L 0x00000000 -#define CFG_DBAT7U 0x00000000 -#define CFG_IBAT7L 0x00000000 -#define CFG_IBAT7U 0x00000000 +#define CONFIG_SYS_DBAT6U ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT6L ((CONFIG_SYS_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U + +/* Map the last 1M of flash where we're running from reset */ +#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ + | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) +#define CONFIG_SYS_DBAT6U_EARLY (TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) +#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ + | BATL_MEMCOHERENCE) +#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY + +#define CONFIG_SYS_DBAT7L 0x00000000 +#define CONFIG_SYS_DBAT7U 0x00000000 +#define CONFIG_SYS_IBAT7L 0x00000000 +#define CONFIG_SYS_IBAT7U 0x00000000 /* * Environment */ #define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000) #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */ #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #include <config_cmd_default.h> #define CONFIG_CMD_PING @@ -491,33 +519,33 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_LOAD_ADDR 0x2000000 /* default load address */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) - #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else - #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ + #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/ /* Cache Configuration */ -#define CFG_DCACHE_SIZE 32768 -#define CFG_CACHELINE_SIZE 32 +#define CONFIG_SYS_DCACHE_SIZE 32768 +#define CONFIG_SYS_CACHELINE_SIZE 32 #if defined(CONFIG_CMD_KGDB) -#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ +#define CONFIG_SYS_CACHELINE_SHIFT 5 /*log base 2 of the above value*/ #endif /* |