summaryrefslogtreecommitdiff
path: root/include/configs/sbc8560.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/sbc8560.h')
-rw-r--r--include/configs/sbc8560.h204
1 files changed, 102 insertions, 102 deletions
diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 38ae1b1..4301275 100644
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -73,9 +73,9 @@
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
@@ -87,17 +87,17 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#if XXX
- #define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
+ #define CONFIG_SYS_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
#else
- #define CFG_CCSRBAR 0xff700000 /* default CCSRBAR */
+ #define CONFIG_SYS_CCSRBAR 0xff700000 /* default CCSRBAR */
#endif
-#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
-#define CFG_SDRAM_SIZE 512 /* DDR is 512MB */
+#define CONFIG_SYS_SDRAM_SIZE 512 /* DDR is 512MB */
/* DDR Setup */
#define CONFIG_FSL_DDR1
@@ -114,8 +114,8 @@
#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_VERY_BIG_RAM
#define CONFIG_NUM_DDR_CONTROLLERS 1
@@ -128,69 +128,69 @@
#undef CONFIG_CLOCKS_IN_MHZ
#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xf8000801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
+ #define CONFIG_SYS_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
+ #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH 8M */
+ #define CONFIG_SYS_BR0_PRELIM 0xf8000801 /* port size 8bit */
+ #define CONFIG_SYS_OR0_PRELIM 0xf8000ff7 /* 8MB Flash */
#else /* Boot from real Flash */
- #define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
- #define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
- #define CFG_BR0_PRELIM 0xff800801 /* port size 8bit */
- #define CFG_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
+ #define CONFIG_SYS_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
+ #define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH 8M */
+ #define CONFIG_SYS_BR0_PRELIM 0xff800801 /* port size 8bit */
+ #define CONFIG_SYS_OR0_PRELIM 0xff800ff7 /* 8MB Flash */
#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/* local bus definitions */
-#define CFG_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
-#define CFG_OR1_PRELIM 0xfc000ff7
+#define CONFIG_SYS_BR1_PRELIM 0xe4001801 /* 64M, 32-bit flash */
+#define CONFIG_SYS_OR1_PRELIM 0xfc000ff7
-#define CFG_BR2_PRELIM 0x00000000 /* CS2 not used */
-#define CFG_OR2_PRELIM 0x00000000
+#define CONFIG_SYS_BR2_PRELIM 0x00000000 /* CS2 not used */
+#define CONFIG_SYS_OR2_PRELIM 0x00000000
-#define CFG_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
-#define CFG_OR3_PRELIM 0xfc000cc1
+#define CONFIG_SYS_BR3_PRELIM 0xf0001861 /* 64MB localbus SDRAM */
+#define CONFIG_SYS_OR3_PRELIM 0xfc000cc1
#if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
+ #define CONFIG_SYS_BR4_PRELIM 0xf4001861 /* 64M localbus SDRAM */
#else
- #define CFG_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
+ #define CONFIG_SYS_BR4_PRELIM 0xf8001861 /* 64M localbus SDRAM */
#endif
-#define CFG_OR4_PRELIM 0xfc000cc1
+#define CONFIG_SYS_OR4_PRELIM 0xfc000cc1
-#define CFG_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
+#define CONFIG_SYS_BR5_PRELIM 0xfc000801 /* 16M CS5 misc devices */
#if 1
- #define CFG_OR5_PRELIM 0xff000ff7
+ #define CONFIG_SYS_OR5_PRELIM 0xff000ff7
#else
- #define CFG_OR5_PRELIM 0xff0000f0
+ #define CONFIG_SYS_OR5_PRELIM 0xff0000f0
#endif
-#define CFG_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
-#define CFG_OR6_PRELIM 0xfc000ff7
-#define CFG_LBC_LCRR 0x00030002 /* local bus freq */
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
+#define CONFIG_SYS_BR6_PRELIM 0xe0001801 /* 64M, 32-bit flash */
+#define CONFIG_SYS_OR6_PRELIM 0xfc000ff7
+#define CONFIG_SYS_LBC_LCRR 0x00030002 /* local bus freq */
+#define CONFIG_SYS_LBC_LBCR 0x00000000
+#define CONFIG_SYS_LBC_LSRT 0x20000000
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
+#define CONFIG_SYS_LBC_LSDMR_1 0x2861b723
+#define CONFIG_SYS_LBC_LSDMR_2 0x0861b723
+#define CONFIG_SYS_LBC_LSDMR_3 0x0861b723
+#define CONFIG_SYS_LBC_LSDMR_4 0x1861b723
+#define CONFIG_SYS_LBC_LSDMR_5 0x4061b723
/* just hijack the MOT BCSR def for SBC8560 misc devices */
-#define CFG_BCSR ((CFG_BR5_PRELIM & 0xff000000)|0x00400000)
+#define CONFIG_SYS_BCSR ((CONFIG_SYS_BR5_PRELIM & 0xff000000)|0x00400000)
/* the size of CS5 needs to be >= 16M for TLB and LAW setups */
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x70000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
@@ -198,22 +198,22 @@
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK 1843200 /* get_bus_freq(0) */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK 1843200 /* get_bus_freq(0) */
#define CONFIG_BAUDRATE 9600
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 ((CFG_BR5_PRELIM & 0xff000000)+0x00700000)
-#define CFG_NS16550_COM2 ((CFG_BR5_PRELIM & 0xff000000)+0x00800000)
+#define CONFIG_SYS_NS16550_COM1 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00700000)
+#define CONFIG_SYS_NS16550_COM2 ((CONFIG_SYS_BR5_PRELIM & 0xff000000)+0x00800000)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/* pass open firmware flat tree */
@@ -227,14 +227,14 @@
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CFG_PCI_MEM_BASE 0xC0000000
-#define CFG_PCI_MEM_PHYS 0xC0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCI_MEM_BASE 0xC0000000
+#define CONFIG_SYS_PCI_MEM_PHYS 0xC0000000
+#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
#ifdef CONFIG_TSEC_ENET
@@ -272,10 +272,10 @@
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
+ #define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CONFIG_SYS_CPMFCR_RAMTYPE 0
+ #define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE)
#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
@@ -305,46 +305,46 @@
* FLASH and environment organization
*/
-#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */
+#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
#if 0
-#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-#define CFG_FLASH_PROTECTION /* use hardware protection */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_PROTECTION /* use hardware protection */
#endif
-#define CFG_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 200000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 50000 /* Timeout for Flash Write (in ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
#if 0
/* XXX This doesn't work and I don't want to fix it */
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
- #define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+ #define CONFIG_SYS_RAMBOOT
#else
- #undef CFG_RAMBOOT
+ #undef CONFIG_SYS_RAMBOOT
#endif
#endif
/* Environment */
-#if !defined(CFG_RAMBOOT)
+#if !defined(CONFIG_SYS_RAMBOOT)
#if defined(CONFIG_RAM_AS_FLASH)
#define CONFIG_ENV_IS_NOWHERE
- #define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x100000)
#define CONFIG_ENV_SIZE 0x2000
#else
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* CONFIG_ENV_SECT_SIZE */
#endif
#else
- #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
@@ -353,7 +353,7 @@
#define CONFIG_BOOTDELAY 5 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
@@ -381,7 +381,7 @@
#define CONFIG_CMD_MII
#endif
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CONFIG_SYS_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
#undef CONFIG_CMD_ENV
#undef CONFIG_CMD_LOADS
#endif
@@ -392,25 +392,25 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "SBC8560=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "SBC8560=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default load address */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Internal Definitions