diff options
Diffstat (limited to 'include/configs/quad100hd.h')
| -rw-r--r-- | include/configs/quad100hd.h | 170 |
1 files changed, 85 insertions, 85 deletions
diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h index 2e73ff7..1a76301 100644 --- a/include/configs/quad100hd.h +++ b/include/configs/quad100hd.h @@ -49,7 +49,7 @@ #define CONFIG_HAS_ETH1 1 #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0x01 /* PHY address */ -#define CFG_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 16 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_PHY_RESET 1 #define CONFIG_PHY_RESET_DELAY 300 /* PHY RESET recovery delay */ @@ -84,59 +84,59 @@ #define CONFIG_SDRAM_BANK0 1 /* FIX! SDRAM timings used in datasheet */ -#define CFG_SDRAM_CL 3 /* CAS latency */ -#define CFG_SDRAM_tRP 20 /* PRECHARGE command period */ -#define CFG_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ -#define CFG_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ -#define CFG_SDRAM_tRFC 66 /* Auto refresh period */ +#define CONFIG_SYS_SDRAM_CL 3 /* CAS latency */ +#define CONFIG_SYS_SDRAM_tRP 20 /* PRECHARGE command period */ +#define CONFIG_SYS_SDRAM_tRC 66 /* ACTIVE-to-ACTIVE command period */ +#define CONFIG_SYS_SDRAM_tRCD 20 /* ACTIVE-to-READ delay */ +#define CONFIG_SYS_SDRAM_tRFC 66 /* Auto refresh period */ /* * JFFS2 */ -#define CFG_JFFS2_FIRST_BANK 0 -#ifdef CFG_KERNEL_IN_JFFS2 -#define CFG_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */ +#define CONFIG_SYS_JFFS2_FIRST_BANK 0 +#ifdef CONFIG_SYS_KERNEL_IN_JFFS2 +#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0 /* JFFS starts at block 0 */ #else /* kernel not in JFFS */ -#define CFG_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */ +#define CONFIG_SYS_JFFS2_FIRST_SECTOR 8 /* block 0-7 is kernel (1MB = 8 sectors) */ #endif -#define CFG_JFFS2_NUM_BANKS 1 +#define CONFIG_SYS_JFFS2_NUM_BANKS 1 /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#define CFG_BASE_BAUD 691200 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#define CONFIG_SYS_BASE_BAUD 691200 #define CONFIG_BAUDRATE 115200 #define CONFIG_SERIAL_MULTI /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_info (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_info (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ @@ -149,53 +149,53 @@ *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F -#define CFG_I2C_EEPROM_ADDR 0x50 /* base address */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* base address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* bytes of address */ -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ -#define CFG_EEPROM_SIZE 0x2000 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 8 byte write page size */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ +#define CONFIG_SYS_EEPROM_SIZE 0x2000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFC00000 -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ -#define CFG_MONITOR_BASE (TEXT_BASE) +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFC00000 +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_MONITOR_BASE (TEXT_BASE) /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_INCREMENT 0 /* there is only one bank */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_INCREMENT 0 /* there is only one bank */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ @@ -210,21 +210,21 @@ #ifdef CONFIG_ENV_IS_IN_EEPROM #define CONFIG_ENV_SIZE 0x400 /* Size of Environment vars */ #define CONFIG_ENV_OFFSET 0x00000000 -#define CFG_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */ +#define CONFIG_SYS_ENABLE_CRC_16 1 /* Intrinsyc formatting used crc16 */ #endif /* partly from PPCBoot */ /* NAND */ #define CONFIG_NAND #ifdef CONFIG_NAND -#define CFG_NAND_BASE 0x60000000 -#define CFG_NAND_CS 10 /* our CS is GPIO10 */ -#define CFG_NAND_RDY 23 /* our RDY is GPIO23 */ -#define CFG_NAND_CE 24 /* our CE is GPIO24 */ -#define CFG_NAND_CLE 31 /* our CLE is GPIO31 */ -#define CFG_NAND_ALE 30 /* our ALE is GPIO30 */ +#define CONFIG_SYS_NAND_BASE 0x60000000 +#define CONFIG_SYS_NAND_CS 10 /* our CS is GPIO10 */ +#define CONFIG_SYS_NAND_RDY 23 /* our RDY is GPIO23 */ +#define CONFIG_SYS_NAND_CE 24 /* our CE is GPIO24 */ +#define CONFIG_SYS_NAND_CLE 31 /* our CLE is GPIO31 */ +#define CONFIG_SYS_NAND_ALE 30 /* our ALE is GPIO30 */ #define NAND_MAX_CHIPS 1 -#define CFG_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 #endif /*----------------------------------------------------------------------- @@ -232,17 +232,17 @@ */ /* use on chip memory (OCM) for temperary stack until sdram is tested */ /* see ./cpu/ppc4xx/start.S */ -#define CFG_TEMP_STACK_OCM 1 +#define CONFIG_SYS_TEMP_STACK_OCM 1 /* On Chip Memory location */ -#define CFG_OCM_DATA_ADDR 0xF8000000 -#define CFG_OCM_DATA_SIZE 0x1000 -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of OCM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup @@ -250,17 +250,17 @@ */ /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */ -#define CFG_EBC_PB0AP 0x04002480 +#define CONFIG_SYS_EBC_PB0AP 0x04002480 /* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */ -#define CFG_EBC_PB0CR 0xFFC5A000 -#define CFG_EBC_PB1AP 0x04005480 -#define CFG_EBC_PB1CR 0x60018000 -#define CFG_EBC_PB2AP 0x00000000 -#define CFG_EBC_PB2CR 0x00000000 -#define CFG_EBC_PB3AP 0x00000000 -#define CFG_EBC_PB3CR 0x00000000 -#define CFG_EBC_PB4AP 0x00000000 -#define CFG_EBC_PB4CR 0x00000000 +#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 +#define CONFIG_SYS_EBC_PB1AP 0x04005480 +#define CONFIG_SYS_EBC_PB1CR 0x60018000 +#define CONFIG_SYS_EBC_PB2AP 0x00000000 +#define CONFIG_SYS_EBC_PB2CR 0x00000000 +#define CONFIG_SYS_EBC_PB3AP 0x00000000 +#define CONFIG_SYS_EBC_PB3CR 0x00000000 +#define CONFIG_SYS_EBC_PB4AP 0x00000000 +#define CONFIG_SYS_EBC_PB4CR 0x00000000 /*----------------------------------------------------------------------- * Definitions for GPIO setup (PPC405EP specific) @@ -268,14 +268,14 @@ * Taken in part from PPCBoot board/icecube/icecube.h */ /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */ -#define CFG_GPIO0_OSRH 0x55555550 -#define CFG_GPIO0_OSRL 0x00000110 -#define CFG_GPIO0_ISR1H 0x00000000 -#define CFG_GPIO0_ISR1L 0x15555445 -#define CFG_GPIO0_TSRH 0x00000000 -#define CFG_GPIO0_TSRL 0x00000000 -#define CFG_GPIO0_TCR 0xFFFF8097 -#define CFG_GPIO0_ODR 0x00000000 +#define CONFIG_SYS_GPIO0_OSRH 0x55555550 +#define CONFIG_SYS_GPIO0_OSRL 0x00000110 +#define CONFIG_SYS_GPIO0_ISR1H 0x00000000 +#define CONFIG_SYS_GPIO0_ISR1L 0x15555445 +#define CONFIG_SYS_GPIO0_TSRH 0x00000000 +#define CONFIG_SYS_GPIO0_TSRL 0x00000000 +#define CONFIG_SYS_GPIO0_TCR 0xFFFF8097 +#define CONFIG_SYS_GPIO0_ODR 0x00000000 #if defined(CONFIG_CMD_KGDB) #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ |