diff options
Diffstat (limited to 'include/configs/pf5200.h')
| -rw-r--r-- | include/configs/pf5200.h | 372 |
1 files changed, 0 insertions, 372 deletions
diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h deleted file mode 100644 index be76478..0000000 --- a/include/configs/pf5200.h +++ /dev/null @@ -1,372 +0,0 @@ -/* - * (C) Copyright 2003-2004 - * Wolfgang Denk, DENX Software Engineering, wd@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/************************************************************************* - * (c) 2005 esd gmbh Hannover - * - * - * from IceCube.h file - * by Reinhard Arlt reinhard.arlt@esd-electronics.com - * - *************************************************************************/ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ - -#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */ -#define CONFIG_ICECUBE 1 /* ... on IceCube board */ -#define CONFIG_PF5200 1 /* ... on PF5200 board */ -#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */ - -#ifndef CONFIG_SYS_TEXT_BASE -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 -#endif - -#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ - -#define CONFIG_HIGH_BATS 1 /* High BATs supported */ -/* - * Serial console configuration - */ -#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ -#if 0 /* test-only */ -#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#else -#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */ -#endif -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -/* - * PCI Mapping: - * 0x40000000 - 0x4fffffff - PCI Memory - * 0x50000000 - 0x50ffffff - PCI IO Space - */ -#define CONFIG_PCI 1 -#define CONFIG_PCI_PNP 1 -#define CONFIG_PCI_SCAN_SHOW 1 -#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1 - -#define CONFIG_PCI_MEM_BUS 0x40000000 -#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS -#define CONFIG_PCI_MEM_SIZE 0x10000000 - -#define CONFIG_PCI_IO_BUS 0x50000000 -#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS -#define CONFIG_PCI_IO_SIZE 0x01000000 - -#define CONFIG_MII 1 -#if 0 /* test-only !!! */ -#define CONFIG_EEPRO100 1 -#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ -#define CONFIG_NS8382X 1 -#endif - -/* Partitions */ -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* USB */ -#if 0 -#define CONFIG_USB_OHCI -#define CONFIG_USB_STORAGE -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_BSP -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF -#define CONFIG_CMD_FAT -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IDE - -#define CONFIG_CMD_PCI - - -#if (CONFIG_SYS_TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT16 1 -#endif -#if (CONFIG_SYS_TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */ -# define CONFIG_SYS_LOWBOOT 1 -# define CONFIG_SYS_LOWBOOT08 1 -#endif - -/* - * Autobooting - */ -#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */ - -#define CONFIG_PREBOOT "echo;" \ - "echo Welcome to ParaFinder pf5200;" \ - "echo" - -#undef CONFIG_BOOTARGS - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "flash_vxworks0=run ata_vxworks_args;setenv loadaddr ff000000;bootvx\0" \ - "flash_vxworks1=run ata_vxworks_args;setenv loadaddr ff200000:bootvx\0" \ - "net_vxworks=phypower 1;sleep 2;tftp ${loadaddr} ${image};run vxworks_args;bootvx\0" \ - "vxworks_args=setenv bootargs fec(0,0)${host}:${image} h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script}\0" \ - "ata_vxworks_args=setenv bootargs /ata0/vxWorks h=${serverip} e=${ipaddr} g=${gatewayip} u=${user} ${pass} tn=${target} s=${script} o=fec0 \0" \ - "loadaddr=01000000\0" \ - "serverip=192.168.2.99\0" \ - "gatewayip=10.0.0.79\0" \ - "user=mu\0" \ - "target=pf5200.esd\0" \ - "script=pf5200.bat\0" \ - "image=/tftpboot/vxWorks_pf5200\0" \ - "ipaddr=10.0.13.196\0" \ - "netmask=255.255.0.0\0" \ - "" - -#define CONFIG_BOOTCOMMAND "run flash_vxworks0" - -/* - * IPB Bus clocking configuration. - */ -#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -/* - * I2C configuration - */ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */ - -#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/* - * EEPROM configuration - */ -#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 -#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 -#define CONFIG_SYS_I2C_MULTI_EEPROMS 1 -/* - * Flash configuration - */ -#define CONFIG_SYS_FLASH_BASE 0xFE000000 -#define CONFIG_SYS_FLASH_SIZE 0x02000000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000) -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 512 - -#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ - -/* - * Environment settings - */ -#if 1 /* test-only */ -#define CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SIZE 0x10000 -#define CONFIG_ENV_SECT_SIZE 0x10000 -#define CONFIG_ENV_OVERWRITE 1 -#else -#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */ -#define CONFIG_ENV_OFFSET 0x0000 /* environment starts at the beginning of the EEPROM */ -#define CONFIG_ENV_SIZE 0x0400 /* 8192 bytes may be used for env vars */ - /* total size of a CAT24WC32 is 8192 bytes */ -#define CONFIG_ENV_OVERWRITE 1 -#endif - -/* - * Memory map - */ -#define CONFIG_SYS_MBAR 0xF0000000 -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 - -/* Use SRAM until RAM will be available */ -#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */ - -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -# define CONFIG_SYS_RAMBOOT 1 -#endif - -#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Ethernet configuration - */ -#define CONFIG_MPC5xxx_FEC 1 -#define CONFIG_MPC5xxx_FEC_MII100 -/* - * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb - */ -/* #define CONFIG_MPC5xxx_FEC_MII10 */ -#define CONFIG_PHY_ADDR 0x00 -#define CONFIG_UDP_CHECKSUM 1 - -/* - * GPIO configuration - */ -#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444 - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -/* - * Various low-level settings - */ -#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI -#define CONFIG_SYS_HID0_FINAL HID0_ICE - -#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE -#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00 - -#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE - -#define CONFIG_SYS_CS1_START 0xfd000000 -#define CONFIG_SYS_CS1_SIZE 0x00010000 -#define CONFIG_SYS_CS1_CFG 0x10101410 - -#define CONFIG_SYS_CS_BURST 0x00000000 -#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 - -#define CONFIG_SYS_RESET_ADDRESS 0xff000000 - -/*----------------------------------------------------------------------- - * USB stuff - *----------------------------------------------------------------------- - */ -#define CONFIG_USB_CLOCK 0x0001BBBB -#define CONFIG_USB_CONFIG 0x00001000 - -/*----------------------------------------------------------------------- - * IDE/ATA stuff Supports IDE harddisk - *----------------------------------------------------------------------- - */ - -#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */ - -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ - -#define CONFIG_IDE_RESET /* reset for ide supported */ -#define CONFIG_IDE_PREINIT - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 - -#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA - -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) - -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) - -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) - -/* Interval between registers */ -#define CONFIG_SYS_ATA_STRIDE 4 - -/*----------------------------------------------------------------------- - * CPLD stuff - */ -#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */ -#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */ - -/* CPLD program pin configuration */ -#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */ -#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */ -#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */ -#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */ - -#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */ -#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */ -#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */ - -#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00) -#define JTAG_GPIO_CFG_SET 0x00000000 -#define JTAG_GPIO_CFG_RESET 0x00F00000 - -#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TMS_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TMS_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */ -#define JTAG_GPIO_TCK_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */ -#define JTAG_GPIO_TCK_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00) -#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDI_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08) -#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */ -#define JTAG_GPIO_TDI_DDR_RESET 0x00000000 - -#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04) -#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */ -#define JTAG_GPIO_TDO_EN_RESET 0x00000000 -#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C) -#define JTAG_GPIO_TDO_DDR_SET 0x00000000 -#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */ - -#endif /* __CONFIG_H */ |