summaryrefslogtreecommitdiff
path: root/include/configs/pf5200.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/pf5200.h')
-rw-r--r--include/configs/pf5200.h188
1 files changed, 94 insertions, 94 deletions
diff --git a/include/configs/pf5200.h b/include/configs/pf5200.h
index 66ad01f..b2e2a1c 100644
--- a/include/configs/pf5200.h
+++ b/include/configs/pf5200.h
@@ -44,7 +44,7 @@
#define CONFIG_PF5200 1 /* ... on PF5200 board */
#define CONFIG_MPC5200_DDR 1 /* ... use DDR RAM */
-#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
+#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
@@ -59,7 +59,7 @@
#else
#define CONFIG_BAUDRATE 9600 /* ... at 115200 bps */
#endif
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
#ifdef CONFIG_MPC5200 /* MPC5100 PCI is not supported yet. */
/*
@@ -84,7 +84,7 @@
#if 0 /* test-only !!! */
#define CONFIG_NET_MULTI 1
#define CONFIG_EEPRO100 1
-#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
#endif
#endif
@@ -127,12 +127,12 @@
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
-# define CFG_LOWBOOT 1
-# define CFG_LOWBOOT16 1
+# define CONFIG_SYS_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT16 1
#endif
#if (TEXT_BASE == 0xFF800000) /* Boot low with 8 MB Flash */
-# define CFG_LOWBOOT 1
-# define CFG_LOWBOOT08 1
+# define CONFIG_SYS_LOWBOOT 1
+# define CONFIG_SYS_LOWBOOT08 1
#endif
/*
@@ -170,36 +170,36 @@
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
/*
* I2C configuration
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CFG_I2C_SPEED 86000 /* 100 kHz */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 86000 /* 100 kHz */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* EEPROM configuration
*/
-#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS 5
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20
-#define CFG_I2C_MULTI_EEPROMS 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
+#define CONFIG_SYS_I2C_MULTI_EEPROMS 1
/*
* Flash configuration
*/
-#define CFG_FLASH_BASE 0xFE000000
-#define CFG_FLASH_SIZE 0x02000000
-#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x00000000)
-#define CFG_MAX_FLASH_BANKS 1 /* max num of memory banks */
-#define CFG_MAX_FLASH_SECT 512
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 0x02000000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00000000)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512
-#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
/*
* Environment settings
@@ -220,26 +220,26 @@
/*
* Memory map
*/
-#define CFG_MBAR 0xF0000000
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_DEFAULT_MBAR 0x80000000
+#define CONFIG_SYS_MBAR 0xF0000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
/* Use SRAM until RAM will be available */
-#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
+#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
+#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT 1
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT 1
#endif
-#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Ethernet configuration
@@ -255,62 +255,62 @@
/*
* GPIO configuration
*/
-#define CFG_GPS_PORT_CONFIG 0x01052444
+#define CONFIG_SYS_GPS_PORT_CONFIG 0x01052444
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
+#define CONFIG_SYS_VXWORKS_MAC_PTR 0x00000000 /* Pass Ethernet MAC to VxWorks */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*
* Various low-level settings
*/
#if defined(CONFIG_MPC5200)
-#define CFG_HID0_INIT HID0_ICE | HID0_ICFI
-#define CFG_HID0_FINAL HID0_ICE
+#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
+#define CONFIG_SYS_HID0_FINAL HID0_ICE
#else
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL 0
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL 0
#endif
-#define CFG_BOOTCS_START CFG_FLASH_BASE
-#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE
-#define CFG_BOOTCS_CFG 0x0004DD00
+#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
+#define CONFIG_SYS_BOOTCS_CFG 0x0004DD00
-#define CFG_CS0_START CFG_FLASH_BASE
-#define CFG_CS0_SIZE CFG_FLASH_SIZE
+#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-#define CFG_CS1_START 0xfd000000
-#define CFG_CS1_SIZE 0x00010000
-#define CFG_CS1_CFG 0x10101410
+#define CONFIG_SYS_CS1_START 0xfd000000
+#define CONFIG_SYS_CS1_SIZE 0x00010000
+#define CONFIG_SYS_CS1_CFG 0x10101410
-#define CFG_CS_BURST 0x00000000
-#define CFG_CS_DEADCYCLE 0x33333333
+#define CONFIG_SYS_CS_BURST 0x00000000
+#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-#define CFG_RESET_ADDRESS 0xff000000
+#define CONFIG_SYS_RESET_ADDRESS 0xff000000
/*-----------------------------------------------------------------------
* USB stuff
@@ -332,71 +332,71 @@
#define CONFIG_IDE_RESET /* reset for ide supported */
#define CONFIG_IDE_PREINIT
-#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CFG_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-#define CFG_ATA_IDE0_OFFSET 0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
/* Offset for data I/O */
-#define CFG_ATA_DATA_OFFSET (0x0060)
+#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060)
/* Offset for normal register accesses */
-#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET)
/* Offset for alternate registers */
-#define CFG_ATA_ALT_OFFSET (0x005C)
+#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C)
/* Interval between registers */
-#define CFG_ATA_STRIDE 4
+#define CONFIG_SYS_ATA_STRIDE 4
/*-----------------------------------------------------------------------
* CPLD stuff
*/
-#define CFG_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
-#define CFG_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
+#define CONFIG_SYS_FPGA_XC95XL 1 /* using Xilinx XC95XL CPLD */
+#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for CPLD */
/* CPLD program pin configuration */
-#define CFG_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
-#define CFG_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
-#define CFG_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
-#define CFG_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */
+#define CONFIG_SYS_FPGA_PRG 0x20000000 /* JTAG TMS pin (ppc output) */
+#define CONFIG_SYS_FPGA_CLK 0x10000000 /* JTAG TCK pin (ppc output) */
+#define CONFIG_SYS_FPGA_DATA 0x20000000 /* JTAG TDO->TDI data pin (ppc output) */
+#define CONFIG_SYS_FPGA_DONE 0x10000000 /* JTAG TDI->TDO pin (ppc input) */
-#define JTAG_GPIO_ADDR_TMS (CFG_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
-#define JTAG_GPIO_ADDR_TCK (CFG_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDI (CFG_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
-#define JTAG_GPIO_ADDR_TDO (CFG_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */
+#define JTAG_GPIO_ADDR_TMS (CONFIG_SYS_MBAR + 0xB10) /* JTAG TMS pin (GPS data out value reg.) */
+#define JTAG_GPIO_ADDR_TCK (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TCK pin (GPW data out value reg.) */
+#define JTAG_GPIO_ADDR_TDI (CONFIG_SYS_MBAR + 0xC0C) /* JTAG TDO->TDI pin (GPW data out value reg.) */
+#define JTAG_GPIO_ADDR_TDO (CONFIG_SYS_MBAR + 0xB14) /* JTAG TDI->TDO pin (GPS data in value reg.) */
-#define JTAG_GPIO_ADDR_CFG (CFG_MBAR + 0xB00)
+#define JTAG_GPIO_ADDR_CFG (CONFIG_SYS_MBAR + 0xB00)
#define JTAG_GPIO_CFG_SET 0x00000000
#define JTAG_GPIO_CFG_RESET 0x00F00000
-#define JTAG_GPIO_ADDR_EN_TMS (CFG_MBAR + 0xB04)
+#define JTAG_GPIO_ADDR_EN_TMS (CONFIG_SYS_MBAR + 0xB04)
#define JTAG_GPIO_TMS_EN_SET 0x20000000 /* Enable for GPIO */
#define JTAG_GPIO_TMS_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TMS (CFG_MBAR + 0xB0C)
+#define JTAG_GPIO_ADDR_DDR_TMS (CONFIG_SYS_MBAR + 0xB0C)
#define JTAG_GPIO_TMS_DDR_SET 0x20000000 /* Set as output */
#define JTAG_GPIO_TMS_DDR_RESET 0x00000000
-#define JTAG_GPIO_ADDR_EN_TCK (CFG_MBAR + 0xC00)
+#define JTAG_GPIO_ADDR_EN_TCK (CONFIG_SYS_MBAR + 0xC00)
#define JTAG_GPIO_TCK_EN_SET 0x20000000 /* Enable for GPIO */
#define JTAG_GPIO_TCK_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TCK (CFG_MBAR + 0xC08)
+#define JTAG_GPIO_ADDR_DDR_TCK (CONFIG_SYS_MBAR + 0xC08)
#define JTAG_GPIO_TCK_DDR_SET 0x20000000 /* Set as output */
#define JTAG_GPIO_TCK_DDR_RESET 0x00000000
-#define JTAG_GPIO_ADDR_EN_TDI (CFG_MBAR + 0xC00)
+#define JTAG_GPIO_ADDR_EN_TDI (CONFIG_SYS_MBAR + 0xC00)
#define JTAG_GPIO_TDI_EN_SET 0x10000000 /* Enable as GPIO */
#define JTAG_GPIO_TDI_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDI (CFG_MBAR + 0xC08)
+#define JTAG_GPIO_ADDR_DDR_TDI (CONFIG_SYS_MBAR + 0xC08)
#define JTAG_GPIO_TDI_DDR_SET 0x10000000 /* Set as output */
#define JTAG_GPIO_TDI_DDR_RESET 0x00000000
-#define JTAG_GPIO_ADDR_EN_TDO (CFG_MBAR + 0xB04)
+#define JTAG_GPIO_ADDR_EN_TDO (CONFIG_SYS_MBAR + 0xB04)
#define JTAG_GPIO_TDO_EN_SET 0x10000000 /* Enable as GPIO */
#define JTAG_GPIO_TDO_EN_RESET 0x00000000
-#define JTAG_GPIO_ADDR_DDR_TDO (CFG_MBAR + 0xB0C)
+#define JTAG_GPIO_ADDR_DDR_TDO (CONFIG_SYS_MBAR + 0xB0C)
#define JTAG_GPIO_TDO_DDR_SET 0x00000000
#define JTAG_GPIO_TDO_DDR_RESET 0x10000000 /* Set as input */