diff options
Diffstat (limited to 'include/configs/mx6dl_sabreauto.h')
| -rw-r--r-- | include/configs/mx6dl_sabreauto.h | 352 |
1 files changed, 352 insertions, 0 deletions
diff --git a/include/configs/mx6dl_sabreauto.h b/include/configs/mx6dl_sabreauto.h new file mode 100644 index 0000000..1288947 --- /dev/null +++ b/include/configs/mx6dl_sabreauto.h @@ -0,0 +1,352 @@ +/* + * Copyright (C) 2012 Freescale Semiconductor, Inc. + * + * Configuration settings for the MX6Solo SABRE-AI Freescale board. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/mx6.h> + + /* High Level Configuration Options */ +#define CONFIG_ARMV7 /* This is armv7 Cortex-A9 CPU core */ +#define CONFIG_MXC +#define CONFIG_MX6DL +#define CONFIG_MX6SOLO_DDR3 +#define CONFIG_DDR_32BIT +#define CONFIG_MX6Q_SABREAUTO +#define CONFIG_FLASH_HEADER +#define CONFIG_FLASH_HEADER_OFFSET 0x400 +#define CONFIG_MX6_CLK32 32768 + +#define CONFIG_SKIP_RELOCATE_UBOOT + +#define CONFIG_ARCH_CPU_INIT +#undef CONFIG_ARCH_MMU /* disable MMU first */ +#define CONFIG_L2_OFF /* disable L2 cache first*/ + +#define CONFIG_MX6_HCLK_FREQ 24000000 + +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_SYS_64BIT_VSPRINTF + +#define BOARD_LATE_INIT + +#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ +#define CONFIG_SERIAL_TAG +#define CONFIG_REVISION_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_MXC_GPIO + +/* + * Size of malloc() pool + */ +#define CONFIG_SYS_MALLOC_LEN (2 * 1024 * 1024) +/* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 + +/* + * Hardware drivers + */ +#define CONFIG_MXC_UART +#define CONFIG_UART_BASE_ADDR UART4_BASE_ADDR + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 +#define CONFIG_SYS_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200} + +/*********************************************************** + * Command definition + ***********************************************************/ + +#include <config_cmd_default.h> + +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_NET_RETRY_COUNT 100 +#define CONFIG_NET_MULTI 1 +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_DNS + +#define CONFIG_CMD_SPI +#define CONFIG_CMD_I2C +#define CONFIG_CMD_IMXOTP +/*Uncomment if wish to view Parallel NOR as device. + *If you want to use it as Boot device you need + *to use mx6solo_sabreauto_boot_weimnor.h + */ +/*#define CONFIG_CMD_WEIMNOR*/ + +/* Enable below configure when supporting nand */ +#define CONFIG_CMD_SF +#define CONFIG_CMD_MMC +#define CONFIG_CMD_ENV +#define CONFIG_CMD_REGUL + +#define CONFIG_CMD_CLOCK +#define CONFIG_REF_CLK_FREQ CONFIG_MX6_HCLK_FREQ + +#undef CONFIG_CMD_IMLS + +#define CONFIG_CMD_IMX_DOWNLOAD_MODE + +#define CONFIG_BOOTDELAY 3 + +#define CONFIG_PRIME "FEC0" + +#define CONFIG_LOADADDR 0x10800000 /* loadaddr env var */ +#define CONFIG_RD_LOADADDR (CONFIG_LOADADDR + 0x300000) + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "ethprime=FEC0\0" \ + "uboot=u-boot.bin\0" \ + "kernel=uImage\0" \ + "nfsroot=/opt/eldk/arm\0" \ + "bootargs_base=setenv bootargs console=ttymxc3,115200 "\ + "nosmp arm_freq=800\0" \ + "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs "\ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0"\ + "bootcmd_net=run bootargs_base bootargs_nfs; " \ + "tftpboot ${loadaddr} ${kernel}; bootm\0" \ + "bootargs_mmc=setenv bootargs ${bootargs} " \ + "root=/dev/mmcblk0p1 rootwait\0" \ + "bootcmd_mmc=run bootargs_base bootargs_mmc; " \ + "mmc dev 2; " \ + "mmc read ${loadaddr} 0x800 0x2000; bootm\0" \ + "bootcmd=run bootcmd_mmc\0" \ + + +#define CONFIG_ARP_TIMEOUT 200UL + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "MX6SOLO SABREAUTO U-Boot > " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ + +#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x10010000 + +#undef CONFIG_SYS_CLKS_IN_HZ /* everything, incl board info, in Hz */ + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR + +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING + +#define CONFIG_FEC0_IOBASE ENET_BASE_ADDR +#define CONFIG_FEC0_PINMUX -1 +#define CONFIG_FEC0_MIIBASE -1 +#define CONFIG_GET_FEC_MAC_ADDR_FROM_IIM +#define CONFIG_MXC_FEC +#define CONFIG_FEC0_PHY_ADDR 1 +#define CONFIG_ETH_PRIME +#define CONFIG_RMII +#define CONFIG_CMD_MII +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_PING +#define CONFIG_IPADDR 192.168.1.103 +#define CONFIG_SERVERIP 192.168.1.101 +#define CONFIG_NETMASK 255.255.255.0 + +/* + * OCOTP Configs + */ +#ifdef CONFIG_CMD_IMXOTP + #define CONFIG_IMX_OTP + #define IMX_OTP_BASE OCOTP_BASE_ADDR + #define IMX_OTP_ADDR_MAX 0x7F + #define IMX_OTP_DATA_ERROR_VAL 0xBADABADA +#endif + +/* + * I2C Configs + */ +#ifdef CONFIG_CMD_I2C + #define CONFIG_HARD_I2C 1 + #define CONFIG_I2C_MXC 1 + #define CONFIG_SYS_I2C_PORT I2C3_BASE_ADDR + #define CONFIG_SYS_I2C_SPEED 100000 + #define CONFIG_SYS_I2C_SLAVE 0x30 +#endif + +/* + * SPI Configs + * SPI NOR AND WEIM NOR share PINs, so cannot be enabled both at sametime + */ +#ifdef CONFIG_CMD_SF + #define CONFIG_FSL_SF 1 + #define CONFIG_SPI_FLASH_IMX_M25PXX 1 + #define CONFIG_SPI_FLASH_CS 1 + #define CONFIG_IMX_ECSPI + #define IMX_CSPI_VER_2_3 1 + #define MAX_SPI_BYTES (64 * 4) +#endif + +/* + * WEIM NOR Config + */ +#ifdef CONFIG_CMD_WEIMNOR + #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ + #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ + #define CONFIG_SYS_FLASH_BASE 0x08000000 /* start of FLASH */ + #define CONFIG_SYS_FLASH_SIZE 0x08000000 /* max flash size in bytes */ + #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE + #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT + #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} + #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ + #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max sectors per device */ + #define CONFIG_SYS_FLASH_PROTECTION +#endif + +/* Regulator Configs */ +#ifdef CONFIG_CMD_REGUL + #define CONFIG_ANATOP_REGULATOR + #define CONFIG_CORE_REGULATOR_NAME "vdd1p1" + #define CONFIG_PERIPH_REGULATOR_NAME "vdd1p1" +#endif + +/* + * MMC Configs + */ +#ifdef CONFIG_CMD_MMC + #define CONFIG_MMC + #define CONFIG_GENERIC_MMC + #define CONFIG_IMX_MMC + #define CONFIG_SYS_FSL_USDHC_NUM 4 + #define CONFIG_SYS_FSL_ESDHC_ADDR 0 + #define CONFIG_SYS_MMC_ENV_DEV 2 + #define CONFIG_DOS_PARTITION 1 + #define CONFIG_CMD_FAT 1 + #define CONFIG_CMD_EXT2 1 + + /* detect whether SD1, 2, 3, or 4 is boot device */ + #define CONFIG_DYNAMIC_MMC_DEVNO + + /* SD3 and SD4 are 8 bit */ + #define CONFIG_MMC_8BIT_PORTS 0xC + /* Setup target delay in DDR mode for each SD port */ + #define CONFIG_GET_DDR_TARGET_DELAY +#endif + +/* + * GPMI Nand Configs + */ +/* #define CONFIG_CMD_NAND */ + +#ifdef CONFIG_CMD_NAND + #define CONFIG_NAND_GPMI + #define CONFIG_GPMI_NFC_SWAP_BLOCK_MARK + #define CONFIG_GPMI_NFC_V2 + + #define CONFIG_GPMI_REG_BASE GPMI_BASE_ADDR + #define CONFIG_BCH_REG_BASE BCH_BASE_ADDR + + #define NAND_MAX_CHIPS 8 + #define CONFIG_SYS_NAND_BASE 0x40000000 + #define CONFIG_SYS_MAX_NAND_DEVICE 1 + + /* NAND is the unique module invoke APBH-DMA */ + #define CONFIG_APBH_DMA + #define CONFIG_APBH_DMA_V2 + #define CONFIG_MXS_DMA_REG_BASE ABPHDMA_BASE_ADDR +#endif + +/*----------------------------------------------------------------------- + * Stack sizes + * + * The stack sizes are set up in start.S using the settings below + */ +#define CONFIG_STACKSIZE (128 * 1024) /* regular stack */ + +/*----------------------------------------------------------------------- + * Physical Memory Map + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM_1 CSD0_DDR_BASE_ADDR +#ifdef CONFIG_DDR_32BIT +#define PHYS_SDRAM_1_SIZE (1u * 1024 * 1024 * 1024) +#else +#define PHYS_SDRAM_1_SIZE (2u * 1024 * 1024 * 1024) +#endif +#define iomem_valid_addr(addr, size) \ + (addr >= PHYS_SDRAM_1 && addr <= (PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE)) + +/*----------------------------------------------------------------------- + * FLASH and environment organization + */ +#ifndef CONFIG_CMD_WEIMNOR + #define CONFIG_SYS_NO_FLASH +#endif +/* Monitor at beginning of flash */ +#define CONFIG_FSL_ENV_IN_MMC +/* #define CONFIG_FSL_ENV_IN_NAND */ + +#define CONFIG_ENV_SECT_SIZE (8 * 1024) +#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE + +#if defined(CONFIG_FSL_ENV_IN_NAND) + #define CONFIG_ENV_IS_IN_NAND 1 + #define CONFIG_ENV_OFFSET 0x100000 +#elif defined(CONFIG_FSL_ENV_IN_MMC) + #define CONFIG_ENV_IS_IN_MMC 1 + #define CONFIG_ENV_OFFSET (768 * 1024) +#elif defined(CONFIG_FSL_ENV_IN_SF) + #define CONFIG_ENV_IS_IN_SPI_FLASH 1 + #define CONFIG_ENV_SPI_CS 1 + #define CONFIG_ENV_OFFSET (768 * 1024) +#else + #define CONFIG_ENV_IS_NOWHERE 1 +#endif + +#ifdef CONFIG_SPLASH_SCREEN + /* + * Framebuffer and LCD + */ + #define CONFIG_LCD + #define CONFIG_IPU_V3H + #define CONFIG_VIDEO_MX5 + #define CONFIG_IPU_CLKRATE 260000000 + #define CONFIG_SYS_CONSOLE_ENV_OVERWRITE + #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE + #define CONFIG_SYS_CONSOLE_IS_IN_ENV + #define LCD_BPP LCD_COLOR16 + #define CONFIG_CMD_BMP + #define CONFIG_BMP_8BPP + #define CONFIG_FB_BASE (TEXT_BASE + 0x300000) + #define CONFIG_SPLASH_SCREEN_ALIGN + #define CONFIG_SYS_WHITE_ON_BLACK +#endif +#endif /* __CONFIG_H */ |