diff options
Diffstat (limited to 'include/configs/munices.h')
| -rw-r--r-- | include/configs/munices.h | 102 |
1 files changed, 51 insertions, 51 deletions
diff --git a/include/configs/munices.h b/include/configs/munices.h index 8f3071a..7682faa 100644 --- a/include/configs/munices.h +++ b/include/configs/munices.h @@ -31,10 +31,10 @@ #define CONFIG_MPC5200 1 /* (more precisely an MPC5200 CPU) */ #define CONFIG_MPC5200_DDR 1 /* (with DDR-SDRAM) */ #define CONFIG_MUNICES 1 /* ... on MUNICes board */ -#define CFG_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33333333 /* ... running at 33.333333MHz */ #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* @@ -50,7 +50,7 @@ #define CONFIG_CMD_REGINFO #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* @@ -58,7 +58,7 @@ */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } #define CONFIG_TIMESTAMP 1 /* Print image info with timestamp */ #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ @@ -91,63 +91,63 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBSPEED_133 /* define for 133MHz speed */ -#if defined(CFG_IPBSPEED_133) +#define CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */ +#if defined(CONFIG_SYS_IPBSPEED_133) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't + * CONFIG_SYS_IPBSPEED_133 is defined. This is because a PCI Clock of 66 MHz yet hasn't * been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCISPEED_66 /* define for 66MHz speed */ +#define CONFIG_SYS_PCISPEED_66 /* define for 66MHz speed */ #else -#undef CFG_PCISPEED_66 /* for 33MHz speed */ +#undef CONFIG_SYS_PCISPEED_66 /* for 33MHz speed */ #endif /* * Memory map */ -#define CFG_MBAR 0xF0000000 /* MBAR hast to be switched by other bootloader or debugger config */ +#define CONFIG_SYS_MBAR 0xF0000000 /* MBAR hast to be switched by other bootloader or debugger config */ -#define CFG_DEFAULT_MBAR 0x80000000 -#define CFG_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* Use SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET - -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Flash configuration */ -#define CFG_FLASH_BASE 0xFF000000 -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_SYS_FLASH_BASE 0xFF000000 +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_SIZE 0x01000000 /* 16 MByte */ -#define CFG_MAX_FLASH_SECT 128 /* max num of sects on one chip */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks (= chip selects) */ -#define CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MByte */ +#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks (= chip selects) */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ /* * Chip selects configuration */ /* Boot Chipselect */ -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#define CFG_BOOTCS_CFG 0x00047800 +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#define CONFIG_SYS_BOOTCS_CFG 0x00047800 /* * Environment settings @@ -172,24 +172,24 @@ /* * GPIO configuration */ -#define CFG_GPS_PORT_CONFIG 0x00058044 /* PSC1=UART, PSC2=UART ; Ether=100MBit with MD +#define CONFIG_SYS_GPS_PORT_CONFIG 0x00058044 /* PSC1=UART, PSC2=UART ; Ether=100MBit with MD no PCI */ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x200000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_DISPLAY_BOARDINFO 1 #define CONFIG_CMDLINE_EDITING 1 @@ -197,12 +197,12 @@ /* * Various low-level settings */ -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333333 -#define CFG_RESET_ADDRESS 0xff000000 +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333333 +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 |