summaryrefslogtreecommitdiff
path: root/include/configs/muas3001.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/muas3001.h')
-rw-r--r--include/configs/muas3001.h190
1 files changed, 95 insertions, 95 deletions
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h
index 1e91b62..f031a17 100644
--- a/include/configs/muas3001.h
+++ b/include/configs/muas3001.h
@@ -80,39 +80,39 @@
* - Rx-CLK is CLK11
* - Tx-CLK is CLK12
*/
-# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
-# define CFG_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12)
+# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK)
/*
* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
*/
-# define CFG_CPMFCR_RAMTYPE (0)
+# define CONFIG_SYS_CPMFCR_RAMTYPE (0)
/* know on local Bus */
-/* define CFG_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */
+/* define CONFIG_SYS_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */
/*
* - Enable Full Duplex in FSMR
*/
-# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB)
#define CONFIG_MII /* MII PHY management */
#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
-# define CFG_PHY_ADDR 1
+# define CONFIG_SYS_PHY_ADDR 1
/*
* GPIO pins used for bit-banged MII communications
*/
#define MDIO_PORT 0 /* Port A */
-#define CFG_MDIO_PIN 0x00200000 /* PA10 */
-#define CFG_MDC_PIN 0x00400000 /* PA9 */
+#define CONFIG_SYS_MDIO_PIN 0x00200000 /* PA10 */
+#define CONFIG_SYS_MDC_PIN 0x00400000 /* PA9 */
-#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN)
-#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN)
-#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0)
+#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN)
+#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN)
+#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0)
-#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \
- else iop->pdat &= ~CFG_MDIO_PIN
+#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDIO_PIN
-#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \
- else iop->pdat &= ~CFG_MDC_PIN
+#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \
+ else iop->pdat &= ~CONFIG_SYS_MDC_PIN
#define MIIDELAY udelay(1)
@@ -188,107 +188,107 @@
/*
* Miscellaneous configurable options
*/
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFF000000
-#define CFG_FLASH_SIZE 32
-#define CFG_FLASH_CFI
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0xFF000000
+#define CONFIG_SYS_FLASH_SIZE 32
+#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */
-#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
-#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CFG_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#endif
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
#define CONFIG_ENV_IS_IN_FLASH
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#endif /* CONFIG_ENV_IS_IN_FLASH */
/*
* I2C Bus
*/
#define CONFIG_HARD_I2C 1 /* To enable I2C support */
-#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
/* I2C SYSMON (LM75, AD7414 is almost compatible) */
#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */
#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP 70
-#define CFG_DTT_LOW_TEMP -30
-#define CFG_DTT_HYSTERESIS 3
+#define CONFIG_SYS_DTT_MAX_TEMP 70
+#define CONFIG_SYS_DTT_LOW_TEMP -30
+#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CFG_IMMR 0xF0000000
-#define CFG_DEFAULT_IMMR 0x0F010000
+#define CONFIG_SYS_IMMR 0xF0000000
+#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/* Hard reset configuration word */
-#define CFG_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */
+#define CONFIG_SYS_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */
/* No slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
-#define CFG_HID0_INIT 0
-#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
+#define CONFIG_SYS_HID0_INIT 0
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE)
-#define CFG_HID2 0
+#define CONFIG_SYS_HID2 0
-#define CFG_SIUMCR 0x00200000
-#define CFG_BCR 0x004c0000
-#define CFG_SCCR 0x0
+#define CONFIG_SYS_SIUMCR 0x00200000
+#define CONFIG_SYS_BCR 0x004c0000
+#define CONFIG_SYS_SCCR 0x0
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 4-35
@@ -297,10 +297,10 @@
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
#else
-#define CFG_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
SYPCR_SWRI|SYPCR_SWP)
#endif /* CONFIG_WATCHDOG */
@@ -309,7 +309,7 @@
*-----------------------------------------------------------------------
* turn on Checkstop Reset Enable
*/
-#define CFG_RMR 0
+#define CONFIG_SYS_RMR 0
/*-----------------------------------------------------------------------
* TMCNTSC - Time Counter Status and Control 4-40
@@ -317,7 +317,7 @@
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 4-42
@@ -325,13 +325,13 @@
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE)
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*
* Init Memory Controller:
@@ -345,60 +345,60 @@
*/
/* Bank 0 - FLASH
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (0xff000020)
+#define CONFIG_SYS_OR0_PRELIM (0xff000020)
/* Bank 1 - 60x bus SDRAM
*/
-#define CFG_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */
-#define CFG_MPTPR 0x2800
+#define CONFIG_SYS_MPTPR 0x2800
/*-----------------------------------------------------------------------------
* Address for Mode Register Set (MRS) command
*-----------------------------------------------------------------------------
*/
-#define CFG_MRS_OFFS 0x00000110
-#define CFG_PSRT 0x13
+#define CONFIG_SYS_MRS_OFFS 0x00000110
+#define CONFIG_SYS_PSRT 0x13
-#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR1_PRELIM CFG_OR1_LITTLE
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_LITTLE
/* SDRAM initialization values
*/
-#define CFG_OR1_LITTLE ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1_LITTLE ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A7 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_LITTLE 0x004b36a3
+#define CONFIG_SYS_PSDMR_LITTLE 0x004b36a3
-#define CFG_OR1_BIG ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR1_BIG ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A4 |\
ORxS_NUMR_12)
-#define CFG_PSDMR_BIG 0x014f36a3
+#define CONFIG_SYS_PSDMR_BIG 0x014f36a3
/* IO on CS4 initialization values
*/
-#define CFG_IO_BASE 0xc0000000
-#define CFG_IO_SIZE 1
+#define CONFIG_SYS_IO_BASE 0xc0000000
+#define CONFIG_SYS_IO_SIZE 1
-#define CFG_BR4_PRELIM ((CFG_IO_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\
BRx_PS_16 | BRx_MS_GPCM_L | BRx_V)
-#define CFG_OR4_PRELIM (0xfff80020)
+#define CONFIG_SYS_OR4_PRELIM (0xfff80020)
-#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
+#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1