diff options
Diffstat (limited to 'include/configs/muas3001.h')
| -rw-r--r-- | include/configs/muas3001.h | 225 |
1 files changed, 127 insertions, 98 deletions
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h index 77e1158..f031a17 100644 --- a/include/configs/muas3001.h +++ b/include/configs/muas3001.h @@ -38,6 +38,9 @@ /* Do boardspecific init */ #define CONFIG_BOARD_EARLY_INIT_R 1 +/* enable Watchdog */ +#define CONFIG_WATCHDOG 1 + /* * Select serial console configuration * @@ -77,39 +80,39 @@ * - Rx-CLK is CLK11 * - Tx-CLK is CLK12 */ -# define CFG_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) -# define CFG_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) +# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF1CS_CLK11 | CMXFCR_TF1CS_CLK12) +# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) /* * - RAM for BD/Buffers is on the 60x Bus (see 28-13) */ -# define CFG_CPMFCR_RAMTYPE (0) +# define CONFIG_SYS_CPMFCR_RAMTYPE (0) /* know on local Bus */ -/* define CFG_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */ +/* define CONFIG_SYS_CPMFCR_RAMTYPE (CPMFCR_DTB | CPMFCR_BDB) */ /* * - Enable Full Duplex in FSMR */ -# define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) +# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) #define CONFIG_MII /* MII PHY management */ #define CONFIG_BITBANGMII /* bit-bang MII PHY management */ -# define CFG_PHY_ADDR 1 +# define CONFIG_SYS_PHY_ADDR 1 /* * GPIO pins used for bit-banged MII communications */ #define MDIO_PORT 0 /* Port A */ -#define CFG_MDIO_PIN 0x00200000 /* PA10 */ -#define CFG_MDC_PIN 0x00400000 /* PA9 */ +#define CONFIG_SYS_MDIO_PIN 0x00200000 /* PA10 */ +#define CONFIG_SYS_MDC_PIN 0x00400000 /* PA9 */ -#define MDIO_ACTIVE (iop->pdir |= CFG_MDIO_PIN) -#define MDIO_TRISTATE (iop->pdir &= ~CFG_MDIO_PIN) -#define MDIO_READ ((iop->pdat & CFG_MDIO_PIN) != 0) +#define MDIO_ACTIVE (iop->pdir |= CONFIG_SYS_MDIO_PIN) +#define MDIO_TRISTATE (iop->pdir &= ~CONFIG_SYS_MDIO_PIN) +#define MDIO_READ ((iop->pdat & CONFIG_SYS_MDIO_PIN) != 0) -#define MDIO(bit) if(bit) iop->pdat |= CFG_MDIO_PIN; \ - else iop->pdat &= ~CFG_MDIO_PIN +#define MDIO(bit) if(bit) iop->pdat |= CONFIG_SYS_MDIO_PIN; \ + else iop->pdat &= ~CONFIG_SYS_MDIO_PIN -#define MDC(bit) if(bit) iop->pdat |= CFG_MDC_PIN; \ - else iop->pdat &= ~CFG_MDC_PIN +#define MDC(bit) if(bit) iop->pdat |= CONFIG_SYS_MDC_PIN; \ + else iop->pdat &= ~CONFIG_SYS_MDC_PIN #define MIIDELAY udelay(1) @@ -124,6 +127,7 @@ */ #include <config_cmd_default.h> +#define CONFIG_CMD_DTT #define CONFIG_CMD_ECHO #define CONFIG_CMD_IMMAP #define CONFIG_CMD_MII @@ -181,112 +185,131 @@ #define CONFIG_BOOTCOMMAND "run net_nfs" #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ - /* * Miscellaneous configurable options */ -#define CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFF000000 -#define CFG_FLASH_SIZE 32 -#define CFG_FLASH_CFI +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFF000000 +#define CONFIG_SYS_FLASH_SIZE 32 +#define CONFIG_SYS_FLASH_CFI #define CONFIG_FLASH_CFI_DRIVER -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -#define CFG_RAMBOOT +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +#define CONFIG_SYS_RAMBOOT #endif -#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */ +#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */ -#define CFG_ENV_IS_IN_FLASH +#define CONFIG_ENV_IS_IN_FLASH -#ifdef CFG_ENV_IS_IN_FLASH -#define CFG_ENV_SECT_SIZE 0x10000 -#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) -#endif /* CFG_ENV_IS_IN_FLASH */ +#ifdef CONFIG_ENV_IS_IN_FLASH +#define CONFIG_ENV_SECT_SIZE 0x10000 +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) +#endif /* CONFIG_ENV_IS_IN_FLASH */ /* * I2C Bus */ #define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F - -#define CFG_IMMR 0xF0000000 -#define CFG_DEFAULT_IMMR 0x0F010000 - -#define CFG_INIT_RAM_ADDR CFG_IMMR -#define CFG_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +/* I2C SYSMON (LM75, AD7414 is almost compatible) */ +#define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ +#define CONFIG_DTT_SENSORS {0} /* Sensor addresses */ +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 + +#define CONFIG_SYS_IMMR 0xF0000000 +#define CONFIG_SYS_DEFAULT_IMMR 0x0F010000 + +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in DPRAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* Hard reset configuration word */ -#define CFG_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */ +#define CONFIG_SYS_HRCW_MASTER 0x0E028200 /* BPS=11 CIP=1 ISB=010 BMS=1 */ /* No slaves */ -#define CFG_HRCW_SLAVE1 0 -#define CFG_HRCW_SLAVE2 0 -#define CFG_HRCW_SLAVE3 0 -#define CFG_HRCW_SLAVE4 0 -#define CFG_HRCW_SLAVE5 0 -#define CFG_HRCW_SLAVE6 0 -#define CFG_HRCW_SLAVE7 0 +#define CONFIG_SYS_HRCW_SLAVE1 0 +#define CONFIG_SYS_HRCW_SLAVE2 0 +#define CONFIG_SYS_HRCW_SLAVE3 0 +#define CONFIG_SYS_HRCW_SLAVE4 0 +#define CONFIG_SYS_HRCW_SLAVE5 0 +#define CONFIG_SYS_HRCW_SLAVE6 0 +#define CONFIG_SYS_HRCW_SLAVE7 0 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ #define BOOTFLAG_WARM 0x02 /* Software reboot */ -#define CFG_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) -#define CFG_HID2 0 +#define CONFIG_SYS_HID2 0 -#define CFG_SIUMCR 0x00200000 -#define CFG_SYPCR 0xFFFFFFC3 -#define CFG_BCR 0x004c0000 -#define CFG_SCCR 0x0 +#define CONFIG_SYS_SIUMCR 0x00200000 +#define CONFIG_SYS_BCR 0x004c0000 +#define CONFIG_SYS_SCCR 0x0 + +/*----------------------------------------------------------------------- + * SYPCR - System Protection Control 4-35 + * SYPCR can only be written once after reset! + *----------------------------------------------------------------------- + * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable + */ +#if defined(CONFIG_WATCHDOG) +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE) +#else +#define CONFIG_SYS_SYPCR (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\ + SYPCR_SWRI|SYPCR_SWP) +#endif /* CONFIG_WATCHDOG */ /*----------------------------------------------------------------------- * RMR - Reset Mode Register 5-5 *----------------------------------------------------------------------- * turn on Checkstop Reset Enable */ -#define CFG_RMR 0 +#define CONFIG_SYS_RMR 0 /*----------------------------------------------------------------------- * TMCNTSC - Time Counter Status and Control 4-40 @@ -294,7 +317,7 @@ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk, * and enable Time Counter */ -#define CFG_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) +#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) /*----------------------------------------------------------------------- * PISCR - Periodic Interrupt Status and Control 4-42 @@ -302,13 +325,13 @@ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable * Periodic timer */ -#define CFG_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) +#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) /*----------------------------------------------------------------------- * RCCR - RISC Controller Configuration 13-7 *----------------------------------------------------------------------- */ -#define CFG_RCCR 0 +#define CONFIG_SYS_RCCR 0 /* * Init Memory Controller: @@ -322,54 +345,60 @@ */ /* Bank 0 - FLASH */ -#define CFG_BR0_PRELIM ((CFG_FLASH_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK) |\ BRx_PS_32 |\ BRx_MS_GPCM_P |\ BRx_V) -#define CFG_OR0_PRELIM (0xff000020) +#define CONFIG_SYS_OR0_PRELIM (0xff000020) /* Bank 1 - 60x bus SDRAM */ -#define SDRAM_MAX_SIZE 0x08000000 /* max. 128 MB */ -#define CFG_GLOBAL_SDRAM_LIMIT (128 << 20) /* less than 128 MB */ +#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT (256 << 20) /* less than 256 MB */ -#define CFG_MPTPR 0x2800 +#define CONFIG_SYS_MPTPR 0x2800 /*----------------------------------------------------------------------------- * Address for Mode Register Set (MRS) command *----------------------------------------------------------------------------- */ -#define CFG_MRS_OFFS 0x00000110 -#define CFG_PSRT 0x13 +#define CONFIG_SYS_MRS_OFFS 0x00000110 +#define CONFIG_SYS_PSRT 0x13 -#define CFG_BR1_PRELIM ((CFG_SDRAM_BASE & BRx_BA_MSK) |\ +#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK) |\ BRx_PS_64 |\ BRx_MS_SDRAM_P |\ BRx_V) -#define CFG_OR1_PRELIM CFG_OR1 +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR1_LITTLE /* SDRAM initialization values */ -#define CFG_OR1 ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ +#define CONFIG_SYS_OR1_LITTLE ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ ORxS_BPD_4 |\ ORxS_ROWST_PBI1_A7 |\ ORxS_NUMR_12) -#define CFG_PSDMR 0x004b36a3 +#define CONFIG_SYS_PSDMR_LITTLE 0x004b36a3 + +#define CONFIG_SYS_OR1_BIG ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\ + ORxS_BPD_4 |\ + ORxS_ROWST_PBI1_A4 |\ + ORxS_NUMR_12) + +#define CONFIG_SYS_PSDMR_BIG 0x014f36a3 /* IO on CS4 initialization values */ -#define CFG_IO_BASE 0xc0000000 -#define CFG_IO_SIZE 1 +#define CONFIG_SYS_IO_BASE 0xc0000000 +#define CONFIG_SYS_IO_SIZE 1 -#define CFG_BR4_PRELIM ((CFG_IO_BASE & BRx_BA_MSK) |\ - BRx_PS_32 | BRx_MS_GPCM_L | BRx_V) +#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_IO_BASE & BRx_BA_MSK) |\ + BRx_PS_16 | BRx_MS_GPCM_L | BRx_V) -#define CFG_OR4_PRELIM (0xfff80020) +#define CONFIG_SYS_OR4_PRELIM (0xfff80020) -#define CFG_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ +#define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC /* "bad" address */ /* pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 |