diff options
Diffstat (limited to 'include/configs/lwmon5.h')
| -rw-r--r-- | include/configs/lwmon5.h | 48 |
1 files changed, 29 insertions, 19 deletions
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index 604b7d1..be48324 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -34,8 +34,8 @@ #define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -72,7 +72,6 @@ * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ #define CFG_OCM_DATA_ADDR CFG_OCM_BASE @@ -143,15 +142,16 @@ #endif /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_ECC_ON | \ +#define CONFIG_POST (CFG_POST_CACHE | \ CFG_POST_CPU | \ - CFG_POST_UART | \ - CFG_POST_I2C | \ - CFG_POST_CACHE | \ - CFG_POST_FPU | \ + CFG_POST_ECC_ON | \ CFG_POST_ETHER | \ - CFG_POST_SPR) + CFG_POST_FPU | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_RTC | \ + CFG_POST_SPR | \ + CFG_POST_UART) #define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ #define CONFIG_LOGBUFFER @@ -162,22 +162,29 @@ *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ + /* 64 byte page write mode using*/ + /* last 6 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ #define CFG_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ + +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ +#if 0 +#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n" +#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ +#endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" +#define CONFIG_PREBOOT "setenv bootdelay 15" #undef CONFIG_BOOTARGS @@ -226,6 +233,7 @@ #define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 300 #define CONFIG_HAS_ETH0 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -391,9 +399,11 @@ #define CFG_GPIO_PHY1_RST 12 #define CFG_GPIO_FLASH_WP 14 #define CFG_GPIO_PHY0_RST 22 -#define CFG_GPIO_WATCHDOG 58 +#define CFG_GPIO_EEPROM_EXT_WP 55 +#define CFG_GPIO_EEPROM_INT_WP 57 #define CFG_GPIO_LIME_S 59 #define CFG_GPIO_LIME_RST 60 +#define CFG_GPIO_WATCHDOG 63 /*----------------------------------------------------------------------- * PPC440 GPIO Configuration |