diff options
Diffstat (limited to 'include/configs/ls2085a_common.h')
-rw-r--r-- | include/configs/ls2085a_common.h | 242 |
1 files changed, 121 insertions, 121 deletions
diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2085a_common.h index e0435cc..e270fc8 100644 --- a/include/configs/ls2085a_common.h +++ b/include/configs/ls2085a_common.h @@ -19,8 +19,20 @@ #define CONFIG_ARM_ERRATA_828024 #define CONFIG_ARM_ERRATA_826974 +#include <asm/arch-fsl-lsch3/config.h> +#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2)) +#define CONFIG_SYS_HAS_SERDES +#endif + +/* We need architecture specific misc initializations */ +#define CONFIG_ARCH_MISC_INIT + /* Link Definitions */ -#define CONFIG_SYS_TEXT_BASE 0x30001000 +#ifdef CONFIG_SPL +#define CONFIG_SYS_TEXT_BASE 0x80400000 +#else +#define CONFIG_SYS_TEXT_BASE 0x30100000 +#endif #ifdef CONFIG_EMU #define CONFIG_SYS_NO_FLASH @@ -39,13 +51,13 @@ #define CONFIG_FIT #define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ +#ifndef CONFIG_SPL #define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */ +#endif #ifndef CONFIG_SYS_FSL_DDR4 #define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */ #define CONFIG_SYS_DDR_RAW_TIMING #endif -#define CONFIG_DIMM_SLOTS_PER_CTLR 1 -#define CONFIG_CHIP_SELECTS_PER_CTRL 4 #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ @@ -69,23 +81,26 @@ #define CONFIG_SYS_DP_DDR_BASE_PHY 0 #define CONFIG_DP_DDR_CTRL 2 #define CONFIG_DP_DDR_NUM_CTRLS 1 -#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1 /* Generic Timer Definitions */ -#define COUNTER_FREQUENCY 12000000 /* 12MHz */ +/* + * This is not an accurate number. It is used in start.S. The frequency + * will be udpated later when get_bus_freq(0) is available. + */ +#define COUNTER_FREQUENCY 25000000 /* 25MHz */ /* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) +#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) /* I2C */ #define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_MXC -#define CONFIG_SYS_MXC_I2C1_SPEED 40000000 -#define CONFIG_SYS_MXC_I2C2_SPEED 40000000 +#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */ +#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */ /* Serial Port */ -#define CONFIG_CONS_INDEX 2 +#define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 @@ -96,131 +111,98 @@ /* IFC */ #define CONFIG_FSL_IFC -#define CONFIG_SYS_NOR0_CSPR_EXT (0x0) -#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) + /* - * During booting, CS0 needs to be at the region of 0x30000000, i.e. the IFC - * address 0. But this region is limited to 256MB. To accommodate bigger NOR - * flash and other devices, we will map CS0 to 0x580000000 after relocation. + * During booting, IFC is mapped at the region of 0x30000000. + * But this region is limited to 256MB. To accommodate NOR, promjet + * and FPGA. This region is divided as below: + * 0x30000000 - 0x37ffffff : 128MB : NOR flash + * 0x38000000 - 0x3BFFFFFF : 64MB : Promjet + * 0x3C000000 - 0x40000000 : 64MB : FPGA etc + * + * To accommodate bigger NOR flash and other devices, we will map IFC + * chip selects to as below: + * 0x5_1000_0000..0x5_1fff_ffff Memory Hole + * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB) + * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB + * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet) + * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet) + * + * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation. * CONFIG_SYS_FLASH_BASE has the final address (core view) * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting */ + #define CONFIG_SYS_FLASH_BASE 0x580000000ULL #define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 -/* - * NOR Flash Timing Params - */ -#define CONFIG_SYS_NOR0_CSPR \ - (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR0_CSPR_EARLY \ - (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY) | \ - CSPR_PORT_SIZE_16 | \ - CSPR_MSEL_NOR | \ - CSPR_V) -#define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(12) -#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x1) | \ - FTIM0_NOR_TEADC(0x1) | \ - FTIM0_NOR_TEAHC(0x1)) -#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x1) | \ - FTIM1_NOR_TRAD_NOR(0x1)) -#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x0) | \ - FTIM2_NOR_TCH(0x0) | \ - FTIM2_NOR_TWP(0x1)) -#define CONFIG_SYS_NOR_FTIM3 0x04000000 -#define CONFIG_SYS_IFC_CCR 0x01000000 +#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000 +#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000 #ifndef CONFIG_SYS_NO_FLASH #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #define CONFIG_SYS_FLASH_QUIET_TEST -#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ - -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ -#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ +#endif -#define CONFIG_SYS_FLASH_EMPTY_INFO -#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } +#ifndef __ASSEMBLY__ +unsigned long long get_qixis_addr(void); #endif +#define QIXIS_BASE get_qixis_addr() +#define QIXIS_BASE_PHYS 0x20000000 +#define QIXIS_BASE_PHYS_EARLY 0xC000000 +#define QIXIS_STAT_PRES1 0xb +#define QIXIS_SDID_MASK 0x07 +#define QIXIS_ESDHC_NO_ADAPTER 0x7 + +#define CONFIG_SYS_NAND_BASE 0x530000000ULL +#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000 -#define CONFIG_NAND_FSL_IFC -#define CONFIG_SYS_NAND_MAX_ECCPOS 256 -#define CONFIG_SYS_NAND_MAX_OOBFREE 2 -#define CONFIG_SYS_NAND_BASE 0x520000000 -#define CONFIG_SYS_NAND_BASE_PHYS 0x20000000 - -#define CONFIG_SYS_NAND_CSPR_EXT (0x0) -#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ - | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ - | CSPR_MSEL_NAND /* MSEL = NAND */ \ - | CSPR_V) -#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) - -#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ - | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ - | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ - | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ - | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ - | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ - | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ - -#define CONFIG_SYS_NAND_ONFI_DETECTION - -/* ONFI NAND Flash mode0 Timing Params */ -#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ - FTIM0_NAND_TWP(0x18) | \ - FTIM0_NAND_TWCHT(0x07) | \ - FTIM0_NAND_TWH(0x0a)) -#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ - FTIM1_NAND_TWBE(0x39) | \ - FTIM1_NAND_TRR(0x0e) | \ - FTIM1_NAND_TRP(0x18)) -#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ - FTIM2_NAND_TREH(0x0a) | \ - FTIM2_NAND_TWHRE(0x1e)) -#define CONFIG_SYS_NAND_FTIM3 0x0 - -#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_CMD_NAND - -#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) - -#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT -#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR_EARLY -#define CONFIG_SYS_CSPR0_FINAL CONFIG_SYS_NOR0_CSPR -#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK -#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR -#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 -#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 -#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 -#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 +/* Debug Server firmware */ +#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024) +/* 2 sec timeout */ +#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT (2 * 1000 * 1000) /* MC firmware */ #define CONFIG_FSL_MC_ENET #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024) -#define CONFIG_SYS_LS_MC_FW_IN_NOR -#define CONFIG_SYS_LS_MC_FW_ADDR 0x580200000ULL -#define CONFIG_SYS_LS_MC_DPL_IN_NOR -#define CONFIG_SYS_LS_MC_DPL_ADDR 0x5806C0000ULL /* TODO Actual DPL max length needs to be confirmed with the MC FW team */ -#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH (256 * 1024) -#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0xe00000 - -/* Carve the MC private DRAM block from the end of DRAM */ -#ifdef CONFIG_FSL_MC_ENET -#define CONFIG_SYS_MEM_TOP_HIDE mc_get_dram_block_size() +#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 +#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 +#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 + +/* Carve out a DDR region which will not be used by u-boot/Linux */ +#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER) +#define CONFIG_SYS_MEM_TOP_HIDE get_dram_size_to_hide() #endif +/* PCIe */ +#define CONFIG_PCIE1 /* PCIE controler 1 */ +#define CONFIG_PCIE2 /* PCIE controler 2 */ +#define CONFIG_PCIE3 /* PCIE controler 3 */ +#define CONFIG_PCIE4 /* PCIE controler 4 */ +#define FSL_PCIE_COMPAT "fsl,20851a-pcie" + +#define CONFIG_SYS_PCI_64BIT + +#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000 +#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */ +#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000 +#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */ + +#define CONFIG_SYS_PCIE_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000 +#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */ + +#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000 +#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000 +#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */ + /* Command line configuration */ #define CONFIG_CMD_CACHE #define CONFIG_CMD_BDI @@ -228,6 +210,7 @@ #define CONFIG_CMD_ENV #define CONFIG_CMD_FLASH #define CONFIG_CMD_IMI +#define CONFIG_CMD_LOADB #define CONFIG_CMD_MEMORY #define CONFIG_CMD_MII #define CONFIG_CMD_NET @@ -237,8 +220,6 @@ #define CONFIG_CMD_BOOTD #define CONFIG_CMD_ECHO #define CONFIG_CMD_SOURCE -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION /* Miscellaneous configurable options */ #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) @@ -247,9 +228,6 @@ /* Physical Memory Map */ /* fixme: these need to be checked against the board */ #define CONFIG_CHIP_SELECTS_PER_CTRL 4 -#define CONFIG_SYS_CLK_FREQ 100000000 -#define CONFIG_DDR_CLK_FREQ 133333333 - #define CONFIG_NR_DRAM_BANKS 3 @@ -265,7 +243,7 @@ "kernel_addr=0x100000\0" \ "ramdisk_addr=0x800000\0" \ "ramdisk_size=0x2000000\0" \ - "fdt_high=0xffffffffffffffff\0" \ + "fdt_high=0xa0000000\0" \ "initrd_high=0xffffffffffffffff\0" \ "kernel_start=0x581200000\0" \ "kernel_load=0xa0000000\0" \ @@ -278,15 +256,11 @@ "hugepages=16" #define CONFIG_BOOTCOMMAND "cp.b $kernel_start $kernel_load " \ "$kernel_size && bootm $kernel_load" -#define CONFIG_BOOTDELAY 1 - -/* Store environment at top of flash */ -#define CONFIG_ENV_IS_NOWHERE 1 -#define CONFIG_ENV_SIZE 0x1000 +#define CONFIG_BOOTDELAY 10 /* Monitor Command Prompt */ #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ -#define CONFIG_SYS_PROMPT "> " +#define CONFIG_SYS_PROMPT "=> " #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_HUSH_PARSER @@ -294,10 +268,36 @@ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ #define CONFIG_SYS_LONGHELP #define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_AUTO_COMPLETE #define CONFIG_SYS_MAXARGS 64 /* max command args */ #ifndef __ASSEMBLY__ -unsigned long mc_get_dram_block_size(void); +unsigned long get_dram_size_to_hide(void); #endif +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +#define CONFIG_SPL_BSS_START_ADDR 0x80100000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000 +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_MAX_SIZE 0x16000 +#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0) +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" +#define CONFIG_SPL_TEXT_BASE 0x1800a000 + +#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000 +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000 +#define CONFIG_SYS_SPL_MALLOC_START 0x80200000 +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) + #endif /* __LS2_COMMON_H */ |