summaryrefslogtreecommitdiff
path: root/include/configs/kmeter1.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/kmeter1.h')
-rw-r--r--include/configs/kmeter1.h332
1 files changed, 14 insertions, 318 deletions
diff --git a/include/configs/kmeter1.h b/include/configs/kmeter1.h
index a3c79a8..16278e1 100644
--- a/include/configs/kmeter1.h
+++ b/include/configs/kmeter1.h
@@ -27,30 +27,20 @@
#define CONFIG_MPC8360 /* MPC8360 CPU specific */
#define CONFIG_KMETER1 /* KMETER1 board specific */
#define CONFIG_HOSTNAME kmeter1
+#define CONFIG_KM_BOARD_NAME "kmeter1"
#define CONFIG_SYS_TEXT_BASE 0xF0000000
#define CONFIG_KM_DEF_NETDEV \
"netdev=eth2\0" \
-/* include common defines/options for all Keymile boards */
-#include "keymile-common.h"
-#include "km-powerpc.h"
-
-#define MTDIDS_DEFAULT "nor0=boot"
-#define MTDPARTS_DEFAULT "mtdparts=" \
- "boot:" \
- "768k(u-boot)," \
- "128k(env)," \
- "128k(envred)," \
- "-(" CONFIG_KM_UBI_PARTITION_NAME ")"
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
#define CONFIG_MISC_INIT_R
/*
- * System Clock Setup
+ * System IO Setup
*/
-#define CONFIG_83XX_CLKIN 66000000
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define CONFIG_83XX_PCICLK 66000000
+#define CONFIG_SYS_SICRH (SICRH_UC1EOBI | SICRH_UC2E1OBI)
/*
* Hardware Reset Configuration Word
@@ -71,55 +61,7 @@
HRCWH_LALE_EARLY | \
HRCWH_LDP_CLEAR )
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH 0x00000006
-#define CONFIG_SYS_SICRL 0x00000000
-
-/*
- * IMMR new address
- */
-#define CONFIG_SYS_IMMR 0xE0000000
-
-/*
- * Bus Arbitration Configuration Register (ACR)
- */
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */
-#define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */
-#define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
- DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-
-#define CFG_83XX_DDR_USES_CS0
-
-#undef CONFIG_DDR_ECC
-
-/*
- * DDRCDR - DDR Control Driver Register
- */
-
-#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */
-
-/*
- * Manually set up DDR parameters
- */
-#define CONFIG_DDR_II
-#define CONFIG_SYS_DDR_SIZE 2048 /* MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f
-#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
- CSCONFIG_ROW_BIT_13 | \
- CSCONFIG_COL_BIT_10 | \
- CSCONFIG_ODT_WR_ACS)
-
#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \
SDRAM_CFG_SREN)
#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
@@ -127,6 +69,11 @@
#define CONFIG_SYS_DDR_INTERVAL ((0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
(0x3cf << SDRAM_INTERVAL_REFINT_SHIFT))
+#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \
+ CSCONFIG_ROW_BIT_13 | \
+ CSCONFIG_COL_BIT_10 | \
+ CSCONFIG_ODT_WR_ACS)
+
#define CONFIG_SYS_DDRCDR 0x40000001
#define CONFIG_SYS_DDR_MODE 0x47860452
#define CONFIG_SYS_DDR_MODE2 0x8080c000
@@ -159,32 +106,13 @@
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_FLASH_BASE 0xF0000000
#define CONFIG_SYS_PIGGY_BASE 0xE8000000
#define CONFIG_SYS_PIGGY_SIZE 128
#define CONFIG_SYS_PAXE_BASE 0xA0000000
#define CONFIG_SYS_PAXE_SIZE 512
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (768 * 1024) /* Reserve for Mon */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK 1
-#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* Local Bus Configuration & Clock Setup
@@ -198,52 +126,9 @@
*
* Bank Bus Machine PortSz Size Device
* ---- --- ------- ------ ----- ------
- * 0 Local GPCM 16 bit 256MB FLASH
- * 1 Local GPCM 8 bit 128MB GPIO/PIGGY
* 3 Local GPCM 8 bit 512MB PAXE
*
*/
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
-#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
-#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
-#define CONFIG_SYS_FLASH_PROTECTION 1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-
-#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */
-
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
- (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
- BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_5 | \
- OR_GPCM_TRLX | OR_GPCM_EAD)
-
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */
-/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_SECT 512
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-
-/*
- * PRIO1/PIGGY on the local bus CS1
- */
-#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE
-#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001A /* 128MB window size */
-
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \
- (1 << BR_PS_SHIFT) | /* 8 bit port size */ \
- BR_V)
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | \
- OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
- OR_GPCM_SCY_2 | \
- OR_GPCM_TRLX | OR_GPCM_EAD)
/*
* PAXE on the local bus CS3
@@ -260,176 +145,14 @@
OR_GPCM_TRLX | OR_GPCM_EAD)
/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
-
-/* Pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#undef CONFIG_PCI /* No PCI */
-
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI
-#endif
-/*
- * QE UEC ethernet configuration
- */
-#define CONFIG_UEC_ETH
-#define CONFIG_ETHPRIME "UEC0"
-
-#define CONFIG_UEC_ETH1 /* GETH1 */
-#define UEC_VERBOSE_DEBUG 1
-
-#ifdef CONFIG_UEC_ETH1
-#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
-#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII */
-#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
-#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
-#define CONFIG_SYS_UEC1_PHY_ADDR 0
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
-#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
-#endif
-
-/*
- * Environment
- */
-
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + \
- CONFIG_SYS_MONITOR_LEN)
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)
-
-/* Address and size of Redundant Environment Sector */
-#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
- CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
-
-#else /* CFG_RAMBOOT */
-#define CONFIG_SYS_NO_FLASH /* Flash is not usable now */
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#define CONFIG_ENV_SIZE 0x2000
-#endif /* CFG_RAMBOOT */
-
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_OFFSET 0x3000
-#define CONFIG_I2C_MULTI_BUS 1
-#define CONFIG_I2C_MUX 1
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible) */
-#define CONFIG_DTT_LM75 /* ON Semi's LM75 */
-#define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */
-#define CONFIG_SYS_DTT_MAX_TEMP 70
-#define CONFIG_SYS_DTT_LOW_TEMP -30
-#define CONFIG_SYS_DTT_HYSTERESIS 3
-#define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS)
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_NAND_KMETER1
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_BASE CONFIG_SYS_PIGGY_BASE
-#endif
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-#if defined(CFG_RAMBOOT)
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_LOADS
-#endif
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (256 << 20)
-
-/*
- * Core HID Setup
- */
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE)
-#define CONFIG_SYS_HID2 HID2_HBE
-
-/*
* MMU Setup
*/
-#define CONFIG_HIGH_BATS /* High BATs supported */
-
-/* DDR: cache cacheable */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | \
- BATU_VP)
-#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
- BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
- BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/* Stack in dcache: cacheable, no memory coherence */
-#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
-#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | \
- BATU_VS | BATU_VP)
-#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
-#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
-
/* PAXE: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
- BATL_MEMCOHERENCE)
+ BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256M | \
- BATU_VS | BATU_VP)
+ BATU_VS | BATU_VP)
#define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
@@ -457,31 +180,4 @@
#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
#endif /* CONFIG_PCI */
-#define BOOTFLASH_START F0000000
-
-#define CONFIG_KM_CONSOLE_TTY "ttyS0"
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ENV_OVERWRITE
-#ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */
-#define CONFIG_KM_DEF_ENV "km-common=empty\0"
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_KM_DEF_ENV \
- "dtt_bus=pca9547:70:a\0" \
- "EEprom_ivm=pca9547:70:9\0" \
- "newenv=" \
- "prot off 0xF00C0000 +0x40000 && " \
- "era 0xF00C0000 +0x40000\0" \
- "rootpath=/opt/eldk/ppc_82xx\0" \
- "unlock=yes\0" \
- ""
-
-#if defined(CONFIG_UEC_ETH)
-#define CONFIG_HAS_ETH0
-#endif
-
#endif /* __CONFIG_H */