diff options
Diffstat (limited to 'include/configs/kilauea.h')
| -rw-r--r-- | include/configs/kilauea.h | 324 |
1 files changed, 162 insertions, 162 deletions
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h index 58918d4..237a9c5 100644 --- a/include/configs/kilauea.h +++ b/include/configs/kilauea.h @@ -53,10 +53,10 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_FLASH_BASE 0xFC000000 -#define CFG_NAND_ADDR 0xF8000000 -#define CFG_FPGA_BASE 0xF0000000 -#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ +#define CONFIG_SYS_FLASH_BASE 0xFC000000 +#define CONFIG_SYS_NAND_ADDR 0xF8000000 +#define CONFIG_SYS_FPGA_BASE 0xF0000000 +#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/ /*----------------------------------------------------------------------- * Initial RAM & Stack Pointer Configuration Options @@ -72,25 +72,25 @@ * the latter of which is less than desireable since it requires * setting up the SDRAM and ECC in assembly code. * - * To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip + * To use (2), define 'CONFIG_SYS_INIT_DCACHE_CS' to be an unused chip * select on the External Bus Controller (EBC) and then select a - * value for 'CFG_INIT_RAM_ADDR' outside of the range of valid, - * physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and - * select a value for 'CFG_INIT_RAM_ADDR' within the range of valid, + * value for 'CONFIG_SYS_INIT_RAM_ADDR' outside of the range of valid, + * physical SDRAM. Otherwise, undefine 'CONFIG_SYS_INIT_DCACHE_CS' and + * select a value for 'CONFIG_SYS_INIT_RAM_ADDR' within the range of valid, * physical SDRAM to use (3). *-----------------------------------------------------------------------*/ -#define CFG_INIT_DCACHE_CS 4 +#define CONFIG_SYS_INIT_DCACHE_CS 4 -#if defined(CFG_INIT_DCACHE_CS) -#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ +#if defined(CONFIG_SYS_INIT_DCACHE_CS) +#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + ( 1 << 30)) /* 1 GiB */ #else -#define CFG_INIT_RAM_ADDR (CFG_SDRAM_BASE + (32 << 20)) /* 32 MiB */ -#endif /* defined(CFG_INIT_DCACHE_CS) */ +#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */ +#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ -#define CFG_INIT_RAM_END (4 << 10) /* 4 KiB */ -#define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_RAM_END (4 << 10) /* 4 KiB */ +#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) /* * If the data cache is being used for the primordial stack and global @@ -100,20 +100,20 @@ * for the POST word. */ -#if defined(CFG_INIT_DCACHE_CS) -# define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET -# define CFG_POST_ALT_WORD_ADDR (CFG_PERIPHERAL_BASE + GPT0_COMP6) +#if defined(CONFIG_SYS_INIT_DCACHE_CS) +# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET +# define CONFIG_SYS_POST_ALT_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6) #else -# define CFG_INIT_EXTRA_SIZE 16 -# define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE) -# define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4) -# define CFG_OCM_DATA_ADDR CFG_INIT_RAM_ADDR -#endif /* defined(CFG_INIT_DCACHE_CS) */ +# define CONFIG_SYS_INIT_EXTRA_SIZE 16 +# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE) +# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4) +# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR +#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ +#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */ /* define this if you want console on UART1 */ #undef CONFIG_UART1_CONSOLE @@ -130,22 +130,22 @@ /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE} +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ #ifdef CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -171,57 +171,57 @@ * set up. While still running from location 0xfffff000...0xffffffff the * NAND controller cannot be accessed since it is attached to CS0 too. */ -#define CFG_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ -#define CFG_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ -#define CFG_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ -#define CFG_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ -#define CFG_NAND_U_BOOT_START CFG_NAND_U_BOOT_DST /* Start NUB from this addr */ -#define CFG_NAND_BOOT_SPL_DELTA (CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST) +#define CONFIG_SYS_NAND_BOOT_SPL_SRC 0xfffff000 /* SPL location */ +#define CONFIG_SYS_NAND_BOOT_SPL_SIZE (4 << 10) /* SPL size */ +#define CONFIG_SYS_NAND_BOOT_SPL_DST 0x00800000 /* Copy SPL here */ +#define CONFIG_SYS_NAND_U_BOOT_DST 0x01000000 /* Load NUB to this addr */ +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */ +#define CONFIG_SYS_NAND_BOOT_SPL_DELTA (CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST) /* * Define the partitioning of the NAND chip (only RAM U-Boot is needed here) */ -#define CFG_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ -#define CFG_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_OFFS (16 << 10) /* Offset to RAM U-Boot image */ +#define CONFIG_SYS_NAND_U_BOOT_SIZE (384 << 10) /* Size of RAM U-Boot image */ /* * Now the NAND chip has to be defined (no autodetection used!) */ -#define CFG_NAND_PAGE_SIZE 512 /* NAND chip page size */ -#define CFG_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ -#define CFG_NAND_PAGE_COUNT 32 /* NAND chip page count */ -#define CFG_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ -#define CFG_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ - -#define CFG_NAND_ECCSIZE 256 -#define CFG_NAND_ECCBYTES 3 -#define CFG_NAND_ECCSTEPS (CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE) -#define CFG_NAND_OOBSIZE 16 -#define CFG_NAND_ECCTOTAL (CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS) -#define CFG_NAND_ECCPOS {0, 1, 2, 3, 6, 7} +#define CONFIG_SYS_NAND_PAGE_SIZE 512 /* NAND chip page size */ +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 << 10) /* NAND chip block size */ +#define CONFIG_SYS_NAND_PAGE_COUNT 32 /* NAND chip page count */ +#define CONFIG_SYS_NAND_BAD_BLOCK_POS 5 /* Location of bad block marker */ +#define CONFIG_SYS_NAND_4_ADDR_CYCLE 1 /* Fourth addr used (>32MB) */ + +#define CONFIG_SYS_NAND_ECCSIZE 256 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE) +#define CONFIG_SYS_NAND_OOBSIZE 16 +#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS) +#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7} #ifdef CONFIG_ENV_IS_IN_NAND /* * For NAND booting the environment is embedded in the U-Boot image. Please take * look at the file board/amcc/sequoia/u-boot-nand.lds for details. */ -#define CONFIG_ENV_SIZE CFG_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET (CFG_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET (CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE) #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) #endif /*----------------------------------------------------------------------- * NAND FLASH *----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_MAX_NAND_DEVICE 1 #define NAND_MAX_CHIPS 1 -#define CFG_NAND_BASE (CFG_NAND_ADDR + CFG_NAND_CS) -#define CFG_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ +#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS) +#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */ /*----------------------------------------------------------------------- * DDR SDRAM *----------------------------------------------------------------------*/ -#define CFG_MBYTES_SDRAM (256) /* 256MB */ +#define CONFIG_SYS_MBYTES_SDRAM (256) /* 256MB */ /* * CONFIG_PPC4xx_DDR_AUTOCALIBRATION @@ -239,55 +239,55 @@ #define DEBUG_PPC4xx_DDR_AUTOCALIBRATION /* dynamic DDR autocal debug */ #undef CONFIG_PPC4xx_DDR_METHOD_A -#define CFG_SDRAM0_MB0CF_BASE (( 0 << 20) + CFG_SDRAM_BASE) +#define CONFIG_SYS_SDRAM0_MB0CF_BASE (( 0 << 20) + CONFIG_SYS_SDRAM_BASE) /* DDR1/2 SDRAM Device Control Register Data Values */ -#define CFG_SDRAM0_MB0CF ((CFG_SDRAM0_MB0CF_BASE >> 3) | \ +#define CONFIG_SYS_SDRAM0_MB0CF ((CONFIG_SYS_SDRAM0_MB0CF_BASE >> 3) | \ SDRAM_RXBAS_SDSZ_256MB | \ SDRAM_RXBAS_SDAM_MODE7 | \ SDRAM_RXBAS_SDBE_ENABLE) -#define CFG_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE -#define CFG_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE -#define CFG_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE -#define CFG_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \ +#define CONFIG_SYS_SDRAM0_MB1CF SDRAM_RXBAS_SDBE_DISABLE +#define CONFIG_SYS_SDRAM0_MB2CF SDRAM_RXBAS_SDBE_DISABLE +#define CONFIG_SYS_SDRAM0_MB3CF SDRAM_RXBAS_SDBE_DISABLE +#define CONFIG_SYS_SDRAM0_MCOPT1 (SDRAM_MCOPT1_PMU_OPEN | \ SDRAM_MCOPT1_8_BANKS | \ SDRAM_MCOPT1_DDR2_TYPE | \ SDRAM_MCOPT1_QDEP | \ SDRAM_MCOPT1_DCOO_DISABLED) -#define CFG_SDRAM0_MCOPT2 0x00000000 -#define CFG_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \ +#define CONFIG_SYS_SDRAM0_MCOPT2 0x00000000 +#define CONFIG_SYS_SDRAM0_MODT0 (SDRAM_MODT_EB0W_ENABLE | \ SDRAM_MODT_EB0R_ENABLE) -#define CFG_SDRAM0_MODT1 0x00000000 -#define CFG_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \ +#define CONFIG_SYS_SDRAM0_MODT1 0x00000000 +#define CONFIG_SYS_SDRAM0_CODT (SDRAM_CODT_RK0R_ON | \ SDRAM_CODT_CKLZ_36OHM | \ SDRAM_CODT_DQS_1_8_V_DDR2 | \ SDRAM_CODT_IO_NMODE) -#define CFG_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560) -#define CFG_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_RTR SDRAM_RTR_RINT_ENCODE(1560) +#define CONFIG_SYS_SDRAM0_INITPLR0 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(80) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_NOP)) -#define CFG_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR1 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(3) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) -#define CFG_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR2 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR2) | \ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR2_TEMP_COMMERCIAL)) -#define CFG_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR3 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR3) | \ SDRAM_INITPLR_IMA_ENCODE(0)) -#define CFG_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR4 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_EMR_DQS_DISABLE | \ JEDEC_MA_EMR_RTT_75OHM)) -#define CFG_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR5 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ @@ -295,31 +295,31 @@ JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ JEDEC_MA_MR_BLEN_4 | \ JEDEC_MA_MR_DLL_RESET)) -#define CFG_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR6 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(3) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_PRECHARGE) | \ SDRAM_INITPLR_IBA_ENCODE(0x0) | \ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_PRECHARGE_ALL)) -#define CFG_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR7 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(26) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) -#define CFG_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR8 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(26) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) -#define CFG_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR9 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(26) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) -#define CFG_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR10 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(26) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_REFRESH)) -#define CFG_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR11 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_MR) | \ SDRAM_INITPLR_IMA_ENCODE(JEDEC_MA_MR_WR_DDR2_3_CYC | \ JEDEC_MA_MR_CL_DDR2_4_0_CLK | \ JEDEC_MA_MR_BLEN_4)) -#define CFG_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR12 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ @@ -328,7 +328,7 @@ JEDEC_MA_EMR_DQS_DISABLE | \ JEDEC_MA_EMR_RTT_DISABLED | \ JEDEC_MA_EMR_ODS_NORMAL)) -#define CFG_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR13 (SDRAM_INITPLR_ENABLE | \ SDRAM_INITPLR_IMWT_ENCODE(2) | \ SDRAM_INITPLR_ICMD_ENCODE(JEDEC_CMD_EMR) | \ SDRAM_INITPLR_IBA_ENCODE(JEDEC_BA_EMR) | \ @@ -337,54 +337,54 @@ JEDEC_MA_EMR_DQS_DISABLE | \ JEDEC_MA_EMR_RTT_DISABLED | \ JEDEC_MA_EMR_ODS_NORMAL)) -#define CFG_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE) -#define CFG_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE) -#define CFG_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \ +#define CONFIG_SYS_SDRAM0_INITPLR14 (SDRAM_INITPLR_DISABLE) +#define CONFIG_SYS_SDRAM0_INITPLR15 (SDRAM_INITPLR_DISABLE) +#define CONFIG_SYS_SDRAM0_RQDC (SDRAM_RQDC_RQDE_ENABLE | \ SDRAM_RQDC_RQFD_ENCODE(56)) -#define CFG_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521) -#define CFG_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2) -#define CFG_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \ +#define CONFIG_SYS_SDRAM0_RFDC SDRAM_RFDC_RFFD_ENCODE(521) +#define CONFIG_SYS_SDRAM0_RDCC (SDRAM_RDCC_RDSS_T2) +#define CONFIG_SYS_SDRAM0_DLCR (SDRAM_DLCR_DCLM_AUTO | \ SDRAM_DLCR_DLCS_CONT_DONE | \ SDRAM_DLCR_DLCV_ENCODE(165)) -#define CFG_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV) -#define CFG_SDRAM0_WRDTR 0x00000000 -#define CFG_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \ +#define CONFIG_SYS_SDRAM0_CLKTR (SDRAM_CLKTR_CLKP_180_DEG_ADV) +#define CONFIG_SYS_SDRAM0_WRDTR 0x00000000 +#define CONFIG_SYS_SDRAM0_SDTR1 (SDRAM_SDTR1_LDOF_2_CLK | \ SDRAM_SDTR1_RTW_2_CLK | \ SDRAM_SDTR1_RTRO_1_CLK) -#define CFG_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \ +#define CONFIG_SYS_SDRAM0_SDTR2 (SDRAM_SDTR2_RCD_3_CLK | \ SDRAM_SDTR2_WTR_2_CLK | \ SDRAM_SDTR2_XSNR_32_CLK | \ SDRAM_SDTR2_WPC_4_CLK | \ SDRAM_SDTR2_RPC_2_CLK | \ SDRAM_SDTR2_RP_3_CLK | \ SDRAM_SDTR2_RRD_2_CLK) -#define CFG_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \ +#define CONFIG_SYS_SDRAM0_SDTR3 (SDRAM_SDTR3_RAS_ENCODE(8) | \ SDRAM_SDTR3_RC_ENCODE(11) | \ SDRAM_SDTR3_XCS | \ SDRAM_SDTR3_RFC_ENCODE(26)) -#define CFG_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \ +#define CONFIG_SYS_SDRAM0_MMODE (SDRAM_MMODE_WR_DDR2_3_CYC | \ SDRAM_MMODE_DCL_DDR2_4_0_CLK | \ SDRAM_MMODE_BLEN_4) -#define CFG_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \ +#define CONFIG_SYS_SDRAM0_MEMODE (SDRAM_MEMODE_DQS_DISABLE | \ SDRAM_MEMODE_RTT_75OHM) /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ -#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* Standard DTT sensor configuration */ #define CONFIG_DTT_DS1775 1 #define CONFIG_DTT_SENSORS { 0 } -#define CFG_I2C_DTT_ADDR 0x48 +#define CONFIG_SYS_I2C_DTT_ADDR 0x48 /* RTC configuration */ #define CONFIG_RTC_DS1338 1 -#define CFG_I2C_RTC_ADDR 0x68 +#define CONFIG_SYS_I2C_RTC_ADDR 0x68 /*----------------------------------------------------------------------- * Ethernet @@ -432,20 +432,20 @@ #define CONFIG_CMD_SNTP /* POST support */ -#define CONFIG_POST (CFG_POST_CACHE | \ - CFG_POST_CPU | \ - CFG_POST_ETHER | \ - CFG_POST_I2C | \ - CFG_POST_MEMORY | \ - CFG_POST_UART) +#define CONFIG_POST (CONFIG_SYS_POST_CACHE | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_ETHER | \ + CONFIG_SYS_POST_I2C | \ + CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_UART) /* Define here the base-addresses of the UARTs to test in POST */ -#define CFG_POST_UART_TABLE {UART0_BASE, UART1_BASE} +#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE} #define CONFIG_LOGBUFFER -#define CFG_POST_CACHE_ADDR 0x00800000 /* free virtual address */ +#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */ -#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ /*----------------------------------------------------------------------- * PCI stuff @@ -458,59 +458,59 @@ /*----------------------------------------------------------------------- * PCIe stuff *----------------------------------------------------------------------*/ -#define CFG_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ -#define CFG_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ +#define CONFIG_SYS_PCIE_MEMBASE 0x90000000 /* mapped PCIe memory */ +#define CONFIG_SYS_PCIE_MEMSIZE 0x08000000 /* 128 Meg, smallest incr per port */ -#define CFG_PCIE0_CFGBASE 0xa0000000 /* remote access */ -#define CFG_PCIE0_XCFGBASE 0xb0000000 /* local access */ -#define CFG_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ +#define CONFIG_SYS_PCIE0_CFGBASE 0xa0000000 /* remote access */ +#define CONFIG_SYS_PCIE0_XCFGBASE 0xb0000000 /* local access */ +#define CONFIG_SYS_PCIE0_CFGMASK 0xe0000001 /* 512 Meg */ -#define CFG_PCIE1_CFGBASE 0xc0000000 /* remote access */ -#define CFG_PCIE1_XCFGBASE 0xd0000000 /* local access */ -#define CFG_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ +#define CONFIG_SYS_PCIE1_CFGBASE 0xc0000000 /* remote access */ +#define CONFIG_SYS_PCIE1_XCFGBASE 0xd0000000 /* local access */ +#define CONFIG_SYS_PCIE1_CFGMASK 0xe0000001 /* 512 Meg */ -#define CFG_PCIE0_UTLBASE 0xef502000 -#define CFG_PCIE1_UTLBASE 0xef503000 +#define CONFIG_SYS_PCIE0_UTLBASE 0xef502000 +#define CONFIG_SYS_PCIE1_UTLBASE 0xef503000 /* base address of inbound PCIe window */ -#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL +#define CONFIG_SYS_PCIE_INBOUND_BASE 0x0000000000000000ULL /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ #if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) /* booting from NAND, so NAND chips select has to be on CS 0 */ -#define CFG_NAND_CS 0 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 0 /* NAND chip connected to CSx */ /* Memory Bank 1 (NOR-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x05806500 -#define CFG_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ +#define CONFIG_SYS_EBC_PB1AP 0x05806500 +#define CONFIG_SYS_EBC_PB1CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ /* Memory Bank 0 (NAND-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x018003c0 -#define CFG_EBC_PB0CR (CFG_NAND_ADDR | 0x1e000) +#define CONFIG_SYS_EBC_PB0AP 0x018003c0 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_NAND_ADDR | 0x1e000) #else -#define CFG_NAND_CS 1 /* NAND chip connected to CSx */ +#define CONFIG_SYS_NAND_CS 1 /* NAND chip connected to CSx */ /* Memory Bank 0 (NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x05806500 -#define CFG_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ +#define CONFIG_SYS_EBC_PB0AP 0x05806500 +#define CONFIG_SYS_EBC_PB0CR 0xFC0DA000 /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/ /* Memory Bank 1 (NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x018003c0 -#define CFG_EBC_PB1CR (CFG_NAND_ADDR | 0x1e000) +#define CONFIG_SYS_EBC_PB1AP 0x018003c0 +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_ADDR | 0x1e000) #endif /* Memory Bank 2 (FPGA) initialization */ -#define CFG_EBC_PB2AP 0x9400C800 -#define CFG_EBC_PB2CR (CFG_FPGA_BASE | 0x18000) +#define CONFIG_SYS_EBC_PB2AP 0x9400C800 +#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE | 0x18000) -#define CFG_EBC_CFG 0x7FC00000 /* EBC0_CFG */ +#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */ /*----------------------------------------------------------------------- * GPIO Setup *----------------------------------------------------------------------*/ -#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ +#define CONFIG_SYS_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \ { \ /* GPIO Core 0 */ \ {GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \ @@ -551,36 +551,36 @@ /*----------------------------------------------------------------------- * Some Kilauea stuff..., mainly fpga registers */ -#define CFG_FPGA_REG_BASE CFG_FPGA_BASE -#define CFG_FPGA_FIFO_BASE (in32(CFG_FPGA_BASE) | (1 << 10)) +#define CONFIG_SYS_FPGA_REG_BASE CONFIG_SYS_FPGA_BASE +#define CONFIG_SYS_FPGA_FIFO_BASE (in32(CONFIG_SYS_FPGA_BASE) | (1 << 10)) /* interrupt */ -#define CFG_FPGA_SLIC0_R_DPRAM_INT 0x80000000 -#define CFG_FPGA_SLIC0_W_DPRAM_INT 0x40000000 -#define CFG_FPGA_SLIC1_R_DPRAM_INT 0x20000000 -#define CFG_FPGA_SLIC1_W_DPRAM_INT 0x10000000 -#define CFG_FPGA_PHY0_INT 0x08000000 -#define CFG_FPGA_PHY1_INT 0x04000000 -#define CFG_FPGA_SLIC0_INT 0x02000000 -#define CFG_FPGA_SLIC1_INT 0x01000000 +#define CONFIG_SYS_FPGA_SLIC0_R_DPRAM_INT 0x80000000 +#define CONFIG_SYS_FPGA_SLIC0_W_DPRAM_INT 0x40000000 +#define CONFIG_SYS_FPGA_SLIC1_R_DPRAM_INT 0x20000000 +#define CONFIG_SYS_FPGA_SLIC1_W_DPRAM_INT 0x10000000 +#define CONFIG_SYS_FPGA_PHY0_INT 0x08000000 +#define CONFIG_SYS_FPGA_PHY1_INT 0x04000000 +#define CONFIG_SYS_FPGA_SLIC0_INT 0x02000000 +#define CONFIG_SYS_FPGA_SLIC1_INT 0x01000000 /* DPRAM setting */ /* 00: 32B; 01: 64B; 10: 128B; 11: 256B */ -#define CFG_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */ -#define CFG_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */ -#define CFG_FPGA_DPRAM_RW_TYPE 0x00080000 -#define CFG_FPGA_DPRAM_RST 0x00040000 -#define CFG_FPGA_UART0_FO 0x00020000 -#define CFG_FPGA_UART1_FO 0x00010000 +#define CONFIG_SYS_FPGA_DPRAM_R_INT_LINE 0x00400000 /* 64 B */ +#define CONFIG_SYS_FPGA_DPRAM_W_INT_LINE 0x00100000 /* 64 B */ +#define CONFIG_SYS_FPGA_DPRAM_RW_TYPE 0x00080000 +#define CONFIG_SYS_FPGA_DPRAM_RST 0x00040000 +#define CONFIG_SYS_FPGA_UART0_FO 0x00020000 +#define CONFIG_SYS_FPGA_UART1_FO 0x00010000 /* loopback */ -#define CFG_FPGA_CHIPSIDE_LOOPBACK 0x00004000 -#define CFG_FPGA_LINESIDE_LOOPBACK 0x00008000 -#define CFG_FPGA_SLIC0_ENABLE 0x00002000 -#define CFG_FPGA_SLIC1_ENABLE 0x00001000 -#define CFG_FPGA_SLIC0_CS 0x00000800 -#define CFG_FPGA_SLIC1_CS 0x00000400 -#define CFG_FPGA_USER_LED0 0x00000200 -#define CFG_FPGA_USER_LED1 0x00000100 +#define CONFIG_SYS_FPGA_CHIPSIDE_LOOPBACK 0x00004000 +#define CONFIG_SYS_FPGA_LINESIDE_LOOPBACK 0x00008000 +#define CONFIG_SYS_FPGA_SLIC0_ENABLE 0x00002000 +#define CONFIG_SYS_FPGA_SLIC1_ENABLE 0x00001000 +#define CONFIG_SYS_FPGA_SLIC0_CS 0x00000800 +#define CONFIG_SYS_FPGA_SLIC1_CS 0x00000400 +#define CONFIG_SYS_FPGA_USER_LED0 0x00000200 +#define CONFIG_SYS_FPGA_USER_LED1 0x00000100 #endif /* __CONFIG_H */ |