diff options
Diffstat (limited to 'include/configs/katmai.h')
| -rw-r--r-- | include/configs/katmai.h | 441 |
1 files changed, 441 insertions, 0 deletions
diff --git a/include/configs/katmai.h b/include/configs/katmai.h new file mode 100644 index 0000000..cc47a16 --- /dev/null +++ b/include/configs/katmai.h @@ -0,0 +1,441 @@ +/* + * (C) Copyright 2007 + * Stefan Roese, DENX Software Engineering, sr@denx.de. + * + * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/************************************************************************ + * katmai.h - configuration for AMCC Katmai (440SPe) + ***********************************************************************/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/*----------------------------------------------------------------------- + * High Level Configuration Options + *----------------------------------------------------------------------*/ +#define CONFIG_KATMAI 1 /* Board is Katmai */ +#define CONFIG_4xx 1 /* ... PPC4xx family */ +#define CONFIG_440 1 /* ... PPC440 family */ +#define CONFIG_440SPE 1 /* Specifc SPe support */ +#undef CFG_DRAM_TEST /* Disable-takes long time */ +#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ + +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ +#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */ +#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ +#undef CONFIG_SHOW_BOOT_PROGRESS + +/*----------------------------------------------------------------------- + * Base addresses -- Note these are effective addresses where the + * actual resources get mapped (not physical addresses) + *----------------------------------------------------------------------*/ +#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */ + +#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */ +#define CFG_MONITOR_BASE TEXT_BASE +#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */ +#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */ + +#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */ +#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE + +#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */ +#define CFG_PCIE_MEMSIZE 0x01000000 +#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */ + +#define CFG_PCIE0_CFGBASE 0xc0000000 +#define CFG_PCIE0_XCFGBASE 0xc0000400 +#define CFG_PCIE1_CFGBASE 0xc0001000 +#define CFG_PCIE1_XCFGBASE 0xc0001400 +#define CFG_PCIE2_CFGBASE 0xc0002000 +#define CFG_PCIE2_XCFGBASE 0xc0002400 + +/* System RAM mapped to PCI space */ +#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE +#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024) + +#define CFG_ACE_BASE 0xfe000000 /* Xilinx ACE controller - Compact Flash */ + +/*----------------------------------------------------------------------- + * Initial RAM & stack pointer (placed in internal SRAM) + *----------------------------------------------------------------------*/ +#define CFG_TEMP_STACK_OCM 1 +#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE +#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ +#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ + +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR + +/*----------------------------------------------------------------------- + * Serial Port + *----------------------------------------------------------------------*/ +#define CONFIG_SERIAL_MULTI 1 +#undef CONFIG_UART1_CONSOLE +#undef CFG_EXT_SERIAL_CLOCK +#define CONFIG_BAUDRATE 115200 +#define CFG_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +/*----------------------------------------------------------------------- + * DDR SDRAM + *----------------------------------------------------------------------*/ +#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */ +#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses*/ +#define CONFIG_DDR_ECC 1 /* with ECC support */ +#undef CONFIG_STRESS + +/*----------------------------------------------------------------------- + * I2C + *----------------------------------------------------------------------*/ +#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_I2C_CMD_TREE +#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */ + +#define IIC0_BOOTPROM_ADDR 0x50 +#define IIC0_ALT_BOOTPROM_ADDR 0x54 + +#define CFG_I2C_MULTI_EEPROMS +#define CFG_I2C_EEPROM_ADDR (0x50) +#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 + +/* I2C RTC */ +#define CONFIG_RTC_M41T11 1 +#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */ +#define CFG_I2C_RTC_ADDR 0x68 +#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */ + +/* I2C DTT */ +#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ +#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */ +/* + * standard dtt sensor configuration - bottom bit will determine local or + * remote sensor of the ADM1021, the rest determines index into + * CFG_DTT_ADM1021 array below. + */ +#define CONFIG_DTT_SENSORS { 0, 1 } + +/* + * ADM1021 temp sensor configuration (see dtt/adm1021.c for details). + * there will be one entry in this array for each two (dummy) sensors in + * CONFIG_DTT_SENSORS. + * + * For Katmai board: + * - only one ADM1021 + * - i2c addr 0x18 + * - conversion rate 0x02 = 0.25 conversions/second + * - ALERT ouput disabled + * - local temp sensor enabled, min set to 0 deg, max set to 85 deg + * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg + */ +#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} } + +/*----------------------------------------------------------------------- + * Environment + *----------------------------------------------------------------------*/ +#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */ + +#define CONFIG_PREBOOT "echo;" \ + "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ + "echo" + +#undef CONFIG_BOOTARGS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "netdev=eth0\0" \ + "hostname=katmai\0" \ + "nfsargs=setenv bootargs root=/dev/nfs rw " \ + "nfsroot=${serverip}:${rootpath}\0" \ + "ramargs=setenv bootargs root=/dev/ram rw\0" \ + "addip=setenv bootargs ${bootargs} " \ + "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ + ":${hostname}:${netdev}:off panic=1\0" \ + "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ + "flash_nfs=run nfsargs addip addtty;" \ + "bootm ${kernel_addr}\0" \ + "flash_self=run ramargs addip addtty;" \ + "bootm ${kernel_addr} ${ramdisk_addr}\0" \ + "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ + "bootm\0" \ + "rootpath=/opt/eldk/ppc_4xx\0" \ + "bootfile=katmai/uImage\0" \ + "kernel_addr=fff10000\0" \ + "ramdisk_addr=fff20000\0" \ + "initrd_high=30000000\0" \ + "load=tftp 200000 katmai/u-boot.bin\0" \ + "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ + "cp.b ${fileaddr} fffc0000 ${filesize};" \ + "setenv filesize;saveenv\0" \ + "upd=run load;run update\0" \ + "kozio=bootm ffc60000\0" \ + "" +#define CONFIG_BOOTCOMMAND "run flash_self" + +#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ + +#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ +#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_ASKENV | \ + CFG_CMD_EEPROM | \ + CFG_CMD_DATE | \ + CFG_CMD_DHCP | \ + CFG_CMD_DIAG | \ + CFG_CMD_DTT | \ + CFG_CMD_ELF | \ + CFG_CMD_EXT2 | \ + CFG_CMD_FAT | \ + CFG_CMD_I2C | \ + CFG_CMD_IRQ | \ + CFG_CMD_MII | \ + CFG_CMD_NET | \ + CFG_CMD_NFS | \ + CFG_CMD_PCI | \ + CFG_CMD_PING | \ + CFG_CMD_REGINFO | \ + CFG_CMD_SDRAM) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */ +#define CONFIG_MII 1 /* MII PHY management */ +#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */ +#define CONFIG_HAS_ETH0 +#define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 1000 +#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */ +#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ +#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ + +#define CONFIG_NETCONSOLE /* include NetConsole support */ +#define CONFIG_NET_MULTI /* needed for NetConsole */ + +#undef CONFIG_WATCHDOG /* watchdog disabled */ + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ + +#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ +#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ + +#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ + +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + +#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ +#define CONFIG_LOOPW 1 /* enable loopw command */ +#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ +#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ +#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ + +#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ + +/*----------------------------------------------------------------------- + * FLASH related + *----------------------------------------------------------------------*/ +#define CFG_FLASH_CFI +#define CFG_FLASH_CFI_DRIVER +#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ + +#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE} +#define CFG_MAX_FLASH_BANKS 1 /* number of banks */ +#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */ + +#undef CFG_FLASH_CHECKSUM +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */ +#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ + +/* Address and size of Redundant Environment Sector */ +#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE) +#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE) + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +/* General PCI */ +#define CONFIG_PCI /* include pci support */ +#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ +#undef CONFIG_PCI_CONFIG_HOST_BRIDGE + +/* Board-specific PCI */ +#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */ +#define CFG_PCI_TARGET_INIT /* let board init pci target */ +#undef CFG_PCI_MASTER_INIT + +#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */ +#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */ + +/* + * NETWORK Support (PCI): + */ +/* Support for Intel 82557/82559/82559ER chips. */ +#define CONFIG_EEPRO100 + +/*----------------------------------------------------------------------- + * Xilinx System ACE support + *----------------------------------------------------------------------*/ +#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */ +#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */ +#define CFG_SYSTEMACE_BASE CFG_ACE_BASE +#define CONFIG_DOS_PARTITION 1 + +/*----------------------------------------------------------------------- + * External Bus Controller (EBC) Setup + *----------------------------------------------------------------------*/ + +/* Memory Bank 0 (Flash) initialization */ +#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(7) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | \ + EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | \ + EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | \ + EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_DELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) +#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | \ + EBC_BXCR_BS_16MB | \ + EBC_BXCR_BU_RW | \ + EBC_BXCR_BW_16BIT) + +/* Memory Bank 1 (Xilinx System ACE controller) initialization */ +#define CFG_EBC_PB1AP (EBC_BXAP_BME_DISABLED | \ + EBC_BXAP_TWT_ENCODE(4) | \ + EBC_BXAP_BCE_DISABLE | \ + EBC_BXAP_BCT_2TRANS | \ + EBC_BXAP_CSN_ENCODE(0) | \ + EBC_BXAP_OEN_ENCODE(0) | \ + EBC_BXAP_WBN_ENCODE(0) | \ + EBC_BXAP_WBF_ENCODE(0) | \ + EBC_BXAP_TH_ENCODE(0) | \ + EBC_BXAP_RE_DISABLED | \ + EBC_BXAP_SOR_NONDELAYED | \ + EBC_BXAP_BEM_WRITEONLY | \ + EBC_BXAP_PEN_DISABLED) +#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \ + EBC_BXCR_BS_1MB | \ + EBC_BXCR_BU_RW | \ + EBC_BXCR_BW_16BIT) + +/*------------------------------------------------------------------------- + * Initialize EBC CONFIG - + * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC + * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000 + *-------------------------------------------------------------------------*/ +#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK | \ + EBC_CFG_PTD_ENABLE | \ + EBC_CFG_RTC_16PERCLK | \ + EBC_CFG_ATC_PREVIOUS | \ + EBC_CFG_DTC_PREVIOUS | \ + EBC_CFG_CTC_PREVIOUS | \ + EBC_CFG_OEO_PREVIOUS | \ + EBC_CFG_EMC_DEFAULT | \ + EBC_CFG_PME_DISABLE | \ + EBC_CFG_PR_16) + +/*----------------------------------------------------------------------- + * GPIO Setup + *----------------------------------------------------------------------*/ +#define CFG_GPIO_PCIE_PRESENT0 17 +#define CFG_GPIO_PCIE_PRESENT1 21 +#define CFG_GPIO_PCIE_PRESENT2 23 +#define CFG_GPIO_RS232_FORCEOFF 30 + +#define CFG_PFC0 (GPIO_VAL(CFG_GPIO_PCIE_PRESENT0) | \ + GPIO_VAL(CFG_GPIO_PCIE_PRESENT1) | \ + GPIO_VAL(CFG_GPIO_PCIE_PRESENT2) | \ + GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)) +#define CFG_GPIO_OR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) +#define CFG_GPIO_TCR GPIO_VAL(CFG_GPIO_RS232_FORCEOFF) +#define CFG_GPIO_ODR 0 + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/ +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */ +#define CFG_CACHELINE_SIZE 32 /* ... */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ +#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ +#endif + +#endif /* __CONFIG_H */ |