summaryrefslogtreecommitdiff
path: root/include/configs/ep8260.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/configs/ep8260.h')
-rw-r--r--include/configs/ep8260.h336
1 files changed, 168 insertions, 168 deletions
diff --git a/include/configs/ep8260.h b/include/configs/ep8260.h
index 9a602c3..d49d02f 100644
--- a/include/configs/ep8260.h
+++ b/include/configs/ep8260.h
@@ -33,7 +33,7 @@
* - 16M Flash (4 x AM29DL323DB90WDI)
* - 128k NVRAM with RTC
*
- * "EP8260 H2, V.1.3" (CFG_EP8260_H2)
+ * "EP8260 H2, V.1.3" (CONFIG_SYS_EP8260_H2)
* - 300MHz/133MHz/66MHz
* - 64M 60x Bus SDRAM
* - 32M Local Bus SDRAM
@@ -45,8 +45,8 @@
#define __CONFIG_H
/* Define this to enable support the EP8260 H2 version */
-#define CFG_EP8260_H2 1
-/* #undef CFG_EP8260_H2 */
+#define CONFIG_SYS_EP8260_H2 1
+/* #undef CONFIG_SYS_EP8260_H2 */
#define CONFIG_CPM2 1 /* Has a CPM2 */
@@ -75,10 +75,10 @@
* 0x6 0x1 66 133 266
* 0x6 0x2 66 133 300
*/
-#ifdef CFG_EP8260_H2
-#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110)
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110)
#else
-#define CFG_SBC_MODCK_H (HRCW_MODCK_H0110)
+#define CONFIG_SYS_SBC_MODCK_H (HRCW_MODCK_H0110)
#endif
/* Define this if you want to boot from 0x00000100. If you don't define
@@ -87,26 +87,26 @@
* way to do that is to program the bootloader at both addresses.
* It is suggested that you just let U-Boot live at 0x00000000.
*/
-/* #define CFG_SBC_BOOT_LOW 1 */ /* only for HRCW */
-/* #undef CFG_SBC_BOOT_LOW */
+/* #define CONFIG_SYS_SBC_BOOT_LOW 1 */ /* only for HRCW */
+/* #undef CONFIG_SYS_SBC_BOOT_LOW */
/* The reset command will not work as expected if the reset address does
* not point to the correct address.
*/
-#define CFG_RESET_ADDRESS 0xFFF00100
+#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
/* What should the base address of the main FLASH be and how big is
* it (in MBytes)? This must contain TEXT_BASE from board/ep8260/config.mk
* The main FLASH is whichever is connected to *CS0. U-Boot expects
* this to be the SIMM.
*/
-#ifdef CFG_EP8260_H2
-#define CFG_FLASH0_BASE 0xFE000000
-#define CFG_FLASH0_SIZE 32
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_FLASH0_BASE 0xFE000000
+#define CONFIG_SYS_FLASH0_SIZE 32
#else
-#define CFG_FLASH0_BASE 0xFF000000
-#define CFG_FLASH0_SIZE 16
+#define CONFIG_SYS_FLASH0_BASE 0xFF000000
+#define CONFIG_SYS_FLASH0_SIZE 16
#endif
/* What should the base address of the secondary FLASH be and how big
@@ -114,41 +114,41 @@
* to *CS6. U-Boot expects this to be the on board FLASH. If you don't
* want it enabled, don't define these constants.
*/
-#define CFG_FLASH1_BASE 0
-#define CFG_FLASH1_SIZE 0
-#undef CFG_FLASH1_BASE
-#undef CFG_FLASH1_SIZE
+#define CONFIG_SYS_FLASH1_BASE 0
+#define CONFIG_SYS_FLASH1_SIZE 0
+#undef CONFIG_SYS_FLASH1_BASE
+#undef CONFIG_SYS_FLASH1_SIZE
/* What should be the base address of SDRAM DIMM (60x bus) and how big is
* it (in Mbytes)?
*/
-#define CFG_SDRAM0_BASE 0x00000000
-#define CFG_SDRAM0_SIZE 64
+#define CONFIG_SYS_SDRAM0_BASE 0x00000000
+#define CONFIG_SYS_SDRAM0_SIZE 64
-/* define CFG_LSDRAM if you want to enable the 32M SDRAM on the
+/* define CONFIG_SYS_LSDRAM if you want to enable the 32M SDRAM on the
* local bus (8260 local bus is NOT cacheable!)
*/
-/* #define CFG_LSDRAM */
-#undef CFG_LSDRAM
+/* #define CONFIG_SYS_LSDRAM */
+#undef CONFIG_SYS_LSDRAM
-#ifdef CFG_LSDRAM
+#ifdef CONFIG_SYS_LSDRAM
/* What should be the base address of SDRAM DIMM (local bus) and how big is
* it (in Mbytes)?
*/
- #define CFG_SDRAM1_BASE 0x04000000
- #define CFG_SDRAM1_SIZE 32
+ #define CONFIG_SYS_SDRAM1_BASE 0x04000000
+ #define CONFIG_SYS_SDRAM1_SIZE 32
#else
- #define CFG_SDRAM1_BASE 0
- #define CFG_SDRAM1_SIZE 0
- #undef CFG_SDRAM1_BASE
- #undef CFG_SDRAM1_SIZE
-#endif /* CFG_LSDRAM */
+ #define CONFIG_SYS_SDRAM1_BASE 0
+ #define CONFIG_SYS_SDRAM1_SIZE 0
+ #undef CONFIG_SYS_SDRAM1_BASE
+ #undef CONFIG_SYS_SDRAM1_SIZE
+#endif /* CONFIG_SYS_LSDRAM */
/* What should be the base address of NVRAM and how big is
* it (in Bytes)
*/
-#define CFG_NVRAM_BASE_ADDR 0xFA080000
-#define CFG_NVRAM_SIZE (128*1024)-16
+#define CONFIG_SYS_NVRAM_BASE_ADDR 0xFA080000
+#define CONFIG_SYS_NVRAM_SIZE (128*1024)-16
/* The RTC is a Dallas DS1556
*/
@@ -157,8 +157,8 @@
/* What should be the base address of the LEDs and switch S0?
* If you don't want them enabled, don't define this.
*/
-#define CFG_LED_BASE 0x00000000
-#undef CFG_LED_BASE
+#define CONFIG_SYS_LED_BASE 0x00000000
+#undef CONFIG_SYS_LED_BASE
/*
* select serial console configuration
@@ -198,21 +198,21 @@
* - RAM for BD/Buffers is on the local Bus (see 28-13)
* - Enable Half Duplex in FSMR
*/
-# define CFG_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CFG_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
/*
* - RAM for BD/Buffers is on the local Bus (see 28-13)
*/
-#ifdef CFG_LSDRAM
- #define CFG_CPMFCR_RAMTYPE 3
-#else /* CFG_LSDRAM */
- #define CFG_CPMFCR_RAMTYPE 0
-#endif /* CFG_LSDRAM */
+#ifdef CONFIG_SYS_LSDRAM
+ #define CONFIG_SYS_CPMFCR_RAMTYPE 3
+#else /* CONFIG_SYS_LSDRAM */
+ #define CONFIG_SYS_CPMFCR_RAMTYPE 0
+#endif /* CONFIG_SYS_LSDRAM */
/* - Enable Half Duplex in FSMR */
-/* # define CFG_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
-# define CFG_FCC_PSMR 0
+/* # define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
+# define CONFIG_SYS_FCC_PSMR 0
#else /* CONFIG_ETHER_INDEX */
# error "on EP8260 ethernet must be FCC3"
@@ -227,8 +227,8 @@
*/
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
/*
* Software (bit-bang) I2C driver configuration
@@ -258,7 +258,7 @@
#define CONFIG_ENV_OVERWRITE
/* What should the console's baud rate be? */
-#ifdef CFG_EP8260_H2
+#ifdef CONFIG_SYS_EP8260_H2
#define CONFIG_BAUDRATE 9600
#else
#define CONFIG_BAUDRATE 115200
@@ -274,10 +274,10 @@
#define CONFIG_BOOTDELAY -1
/* undef this to save memory */
-#define CFG_LONGHELP
+#define CONFIG_SYS_LONGHELP
/* Monitor Command Prompt */
-#define CFG_PROMPT "=> "
+#define CONFIG_SYS_PROMPT "=> "
/* Define this variable to enable the "hush" shell (from
Busybox) as command line interpreter, thus enabling
@@ -287,8 +287,8 @@
If undefined, you get the old, much simpler behaviour
with a somewhat smapper memory footprint.
*/
-#define CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
/*
@@ -327,11 +327,11 @@
#undef CONFIG_CMD_XIMG
/* Where do the internal registers live? */
-#define CFG_IMMR 0xF0000000
-#define CFG_DEFAULT_IMMR 0x00010000
+#define CONFIG_SYS_IMMR 0xF0000000
+#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
/* Where do the on board registers (CS4) live? */
-#define CFG_REGS_BASE 0xFA000000
+#define CONFIG_SYS_REGS_BASE 0xFA000000
/*****************************************************************************
*
@@ -348,35 +348,35 @@
* Miscellaneous configurable options
*/
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-# define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
-#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT)+16)
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-#define CFG_MAXARGS 8 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#ifdef CFG_LSDRAM
- #define CFG_MEMTEST_START 0x04000000 /* memtest works on */
- #define CFG_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
+#ifdef CONFIG_SYS_LSDRAM
+ #define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
+ #define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
#else
- #define CFG_MEMTEST_START 0x00000000 /* memtest works on */
- #define CFG_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */
-#endif /* CFG_LSDRAM */
+ #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+ #define CONFIG_SYS_MEMTEST_END 0x02000000 /* 0-32 MB in SDRAM */
+#endif /* CONFIG_SYS_LSDRAM */
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-#define CFG_LOAD_ADDR 0x00100000 /* default load address */
-#define CFG_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */
+#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
+#define CONFIG_SYS_TFTP_LOADADDR 0x00100000 /* default load address for network file downloads */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
/* valid baudrates */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
@@ -384,119 +384,119 @@
* You should know what you are doing if you make changes here.
*/
-#define CFG_FLASH_BASE CFG_FLASH0_BASE
-#define CFG_SDRAM_BASE CFG_SDRAM0_BASE
+#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
/*-----------------------------------------------------------------------
* Hard Reset Configuration Words
*/
-#if defined(CFG_SBC_BOOT_LOW)
-# define CFG_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
+#if defined(CONFIG_SYS_SBC_BOOT_LOW)
+# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
#else
-# define CFG_SBC_HRCW_BOOT_FLAGS (0x00000000)
-#endif /* defined(CFG_SBC_BOOT_LOW) */
+# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0x00000000)
+#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-#ifdef CFG_EP8260_H2
-/* get the HRCW ISB field from CFG_DEFAULT_IMMR */
-#define CFG_SBC_HRCW_IMMR ( ((CFG_DEFAULT_IMMR & 0x10000000) >> 10) |\
- ((CFG_DEFAULT_IMMR & 0x01000000) >> 7) |\
- ((CFG_DEFAULT_IMMR & 0x00100000) >> 4) )
+#ifdef CONFIG_SYS_EP8260_H2
+/* get the HRCW ISB field from CONFIG_SYS_DEFAULT_IMMR */
+#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_DEFAULT_IMMR & 0x10000000) >> 10) |\
+ ((CONFIG_SYS_DEFAULT_IMMR & 0x01000000) >> 7) |\
+ ((CONFIG_SYS_DEFAULT_IMMR & 0x00100000) >> 4) )
-#define CFG_HRCW_MASTER (HRCW_EBM |\
+#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM |\
HRCW_L2CPC01 |\
- CFG_SBC_HRCW_IMMR |\
+ CONFIG_SYS_SBC_HRCW_IMMR |\
HRCW_APPC10 |\
HRCW_CS10PC01 |\
- CFG_SBC_MODCK_H |\
- CFG_SBC_HRCW_BOOT_FLAGS)
+ CONFIG_SYS_SBC_MODCK_H |\
+ CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
#else
-#define CFG_HRCW_MASTER 0x10400245
+#define CONFIG_SYS_HRCW_MASTER 0x10400245
#endif
/* no slaves */
-#define CFG_HRCW_SLAVE1 0
-#define CFG_HRCW_SLAVE2 0
-#define CFG_HRCW_SLAVE3 0
-#define CFG_HRCW_SLAVE4 0
-#define CFG_HRCW_SLAVE5 0
-#define CFG_HRCW_SLAVE6 0
-#define CFG_HRCW_SLAVE7 0
+#define CONFIG_SYS_HRCW_SLAVE1 0
+#define CONFIG_SYS_HRCW_SLAVE2 0
+#define CONFIG_SYS_HRCW_SLAVE3 0
+#define CONFIG_SYS_HRCW_SLAVE4 0
+#define CONFIG_SYS_HRCW_SLAVE5 0
+#define CONFIG_SYS_HRCW_SLAVE6 0
+#define CONFIG_SYS_HRCW_SLAVE7 0
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CFG_RAMBOOT is platform dependent.
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
*/
-#define CFG_MONITOR_BASE TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-# define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+# define CONFIG_SYS_RAMBOOT
#endif
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#ifdef CFG_EP8260_H2
-#define CFG_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
#else
-#define CFG_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
#endif
-#ifdef CFG_EP8260_H2
-#define CFG_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#else
-#define CFG_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
#endif
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
# define CONFIG_ENV_IS_IN_FLASH 1
# ifdef CONFIG_ENV_IN_OWN_SECT
-# define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
# define CONFIG_ENV_SECT_SIZE 0x40000
# else
-# define CONFIG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
+# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
# endif /* CONFIG_ENV_IN_OWN_SECT */
#else
# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
# define CONFIG_ENV_SIZE 0x200
-#endif /* CFG_RAMBOOT */
+#endif /* CONFIG_SYS_RAMBOOT */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 32 /* For MPC8260 CPU */
+#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
@@ -509,38 +509,38 @@
*
* HID1 has only read-only information - nothing to set.
*/
-#define CFG_HID0_INIT (HID0_ICE |\
+#define CONFIG_SYS_HID0_INIT (HID0_ICE |\
HID0_DCE |\
HID0_ICFI |\
HID0_DCI |\
HID0_IFEM |\
HID0_ABE)
-#ifdef CFG_LSDRAM
+#ifdef CONFIG_SYS_LSDRAM
/* 8260 local bus is NOT cacheable */
-#define CFG_HID0_FINAL (/*HID0_ICE |*/\
+#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
-#else /* !CFG_LSDRAM */
-#define CFG_HID0_FINAL (HID0_ICE |\
+#else /* !CONFIG_SYS_LSDRAM */
+#define CONFIG_SYS_HID0_FINAL (HID0_ICE |\
HID0_IFEM |\
HID0_ABE |\
HID0_EMCP)
-#endif /* CFG_LSDRAM */
+#endif /* CONFIG_SYS_LSDRAM */
-#define CFG_HID2 0
+#define CONFIG_SYS_HID2 0
/*-----------------------------------------------------------------------
* RMR - Reset Mode Register
*-----------------------------------------------------------------------
*/
-#define CFG_RMR 0
+#define CONFIG_SYS_RMR 0
/*-----------------------------------------------------------------------
* BCR - Bus Configuration 4-25
*-----------------------------------------------------------------------
*/
-#define CFG_BCR (BCR_EBM |\
+#define CONFIG_SYS_BCR (BCR_EBM |\
BCR_PLDP |\
BCR_EAV |\
BCR_NPQM0)
@@ -549,7 +549,7 @@
* SIUMCR - SIU Module Configuration 4-31
*-----------------------------------------------------------------------
*/
-#define CFG_SIUMCR (SIUMCR_L2CPC01 |\
+#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\
SIUMCR_APPC10 |\
SIUMCR_CS10PC01)
@@ -559,25 +559,25 @@
*-----------------------------------------------------------------------
* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
*/
-#ifdef CFG_EP8260_H2
+#ifdef CONFIG_SYS_EP8260_H2
/* TBD: Find out why setting the BMT to 0xff causes the FCC to
* generate TX buffer underrun errors for large packets under
* Linux
*/
-#define CFG_SYPCR_BMT 0x00000600
+#define CONFIG_SYS_SYPCR_BMT 0x00000600
#else
-#define CFG_SYPCR_BMT SYPCR_BMT
+#define CONFIG_SYS_SYPCR_BMT SYPCR_BMT
#endif
-#ifdef CFG_LSDRAM
-#define CFG_SYPCR (SYPCR_SWTC |\
- CFG_SYPCR_BMT |\
+#ifdef CONFIG_SYS_LSDRAM
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
+ CONFIG_SYS_SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_LBME |\
SYPCR_SWP)
#else
-#define CFG_SYPCR (SYPCR_SWTC |\
- CFG_SYPCR_BMT |\
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
+ CONFIG_SYS_SYPCR_BMT |\
SYPCR_PBME |\
SYPCR_SWP)
#endif
@@ -588,7 +588,7 @@
* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
* and enable Time Counter
*/
-#define CFG_TMCNTSC (TMCNTSC_SEC |\
+#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
TMCNTSC_ALR |\
TMCNTSC_TCF |\
TMCNTSC_TCE)
@@ -599,35 +599,35 @@
* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
* Periodic timer
*/
-#ifdef CFG_EP8260_H2
-#define CFG_PISCR (PISCR_PS |\
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_PISCR (PISCR_PS |\
PISCR_PTF |\
PISCR_PTE)
#else
-#define CFG_PISCR 0
+#define CONFIG_SYS_PISCR 0
#endif
/*-----------------------------------------------------------------------
* SCCR - System Clock Control 9-8
*-----------------------------------------------------------------------
*/
-#ifdef CFG_EP8260_H2
-#define CFG_SCCR (SCCR_DFBRG00)
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_SCCR (SCCR_DFBRG00)
#else
-#define CFG_SCCR (SCCR_DFBRG01)
+#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
#endif
/*-----------------------------------------------------------------------
* RCCR - RISC Controller Configuration 13-7
*-----------------------------------------------------------------------
*/
-#define CFG_RCCR 0
+#define CONFIG_SYS_RCCR 0
/*-----------------------------------------------------------------------
* MPTPR - Memory Refresh Timer Prescale Register 10-32
*-----------------------------------------------------------------------
*/
-#define CFG_MPTPR (0x0A00 & MPTPR_PTP_MSK)
+#define CONFIG_SYS_MPTPR (0x0A00 & MPTPR_PTP_MSK)
/*
* Init Memory Controller:
@@ -659,13 +659,13 @@
/* Bank 0 - FLASH
*
*/
-#define CFG_BR0_PRELIM ((CFG_FLASH0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_DECC_NONE |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR0_PRELIM (MEG_TO_AM(CFG_FLASH0_SIZE) |\
+#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_8_CLK |\
@@ -674,71 +674,71 @@
/* Bank 1 - SDRAM
* PSDRAM
*/
-#define CFG_BR1_PRELIM ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
BRx_PS_64 |\
BRx_MS_SDRAM_P |\
BRx_V)
-#define CFG_OR1_PRELIM (MEG_TO_AM(CFG_SDRAM0_SIZE) |\
+#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI1_A6 |\
ORxS_NUMR_12)
-#ifdef CFG_EP8260_H2
-#define CFG_PSDMR 0xC34E246E
+#ifdef CONFIG_SYS_EP8260_H2
+#define CONFIG_SYS_PSDMR 0xC34E246E
#else
-#define CFG_PSDMR 0xC34E2462
+#define CONFIG_SYS_PSDMR 0xC34E2462
#endif
-#define CFG_PSRT 0x64
+#define CONFIG_SYS_PSRT 0x64
-#ifdef CFG_LSDRAM
+#ifdef CONFIG_SYS_LSDRAM
/* Bank 2 - SDRAM
* LSDRAM
*/
- #define CFG_BR2_PRELIM ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\
+ #define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
BRx_PS_32 |\
BRx_MS_SDRAM_L |\
BRx_V)
- #define CFG_OR2_PRELIM (MEG_TO_AM(CFG_SDRAM1_SIZE) |\
+ #define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
ORxS_BPD_4 |\
ORxS_ROWST_PBI0_A9 |\
ORxS_NUMR_12)
- #define CFG_LSDMR 0x416A2562
- #define CFG_LSRT 0x64
+ #define CONFIG_SYS_LSDMR 0x416A2562
+ #define CONFIG_SYS_LSRT 0x64
#else
- #define CFG_LSRT 0x0
-#endif /* CFG_LSDRAM */
+ #define CONFIG_SYS_LSRT 0x0
+#endif /* CONFIG_SYS_LSDRAM */
/* Bank 4 - On board registers
* NVRTC and BCSR
*/
-#define CFG_BR4_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
BRx_PS_8 |\
BRx_MS_GPCM_P |\
BRx_V)
/*
-#define CFG_OR4_PRELIM (ORxG_AM_MSK |\
+#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SCY_10_CLK |\
ORxG_TRLX)
*/
-#define CFG_OR4_PRELIM 0xfff00854
+#define CONFIG_SYS_OR4_PRELIM 0xfff00854
#ifdef _NOT_USED_SINCE_NOT_WORKING_
/* Bank 8 - On board registers
* PCMCIA (currently not working!)
*/
-#define CFG_BR8_PRELIM ((CFG_REGS_BASE & BRx_BA_MSK) |\
+#define CONFIG_SYS_BR8_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
BRx_PS_16 |\
BRx_MS_GPCM_P |\
BRx_V)
-#define CFG_OR8_PRELIM (ORxG_AM_MSK |\
+#define CONFIG_SYS_OR8_PRELIM (ORxG_AM_MSK |\
ORxG_CSNT |\
ORxG_ACS_DIV1 |\
ORxG_SETA |\