diff options
Diffstat (limited to 'include/configs/ep8248.h')
| -rw-r--r-- | include/configs/ep8248.h | 253 |
1 files changed, 0 insertions, 253 deletions
diff --git a/include/configs/ep8248.h b/include/configs/ep8248.h deleted file mode 100644 index f1af96d..0000000 --- a/include/configs/ep8248.h +++ /dev/null @@ -1,253 +0,0 @@ -/* - * Copyright (C) 2004 Arabella Software Ltd. - * Yuli Barcohen <yuli@arabellasw.com> - * - * U-Boot configuration for Embedded Planet EP8248 boards. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MPC8248 -#define CPU_ID_STR "MPC8248" - -#define CONFIG_EP8248 /* Embedded Planet EP8248 board */ - -#define CONFIG_SYS_TEXT_BASE 0xFFF00000 - -#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ - -/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */ -#define CONFIG_ENV_OVERWRITE - -/* - * Select serial console configuration - * - * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then - * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4 - * for SCC). - */ -#define CONFIG_CONS_ON_SMC /* Console is on SMC */ -#undef CONFIG_CONS_ON_SCC /* It's not on SCC */ -#undef CONFIG_CONS_NONE /* It's not on external UART */ -#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */ - -#define CONFIG_SYS_BCSR 0xFA000000 - -/* Pass open firmware flat device tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - -#define OF_TBCLK (bd->bi_busfreq / 4) -#define OF_STDOUT_PATH "/soc/cpm/serial <at> 11a80" - -/* Select ethernet configuration */ -#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */ -#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */ -#undef CONFIG_ETHER_NONE /* No external Ethernet */ - -#define CONFIG_SYS_CPMFCR_RAMTYPE 0 -#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE | FCC_PSMR_LPB) - -#define CONFIG_HAS_ETH0 -#define CONFIG_ETHER_ON_FCC1 1 -/* - Rx clock is CLK10 - * - Tx clock is CLK11 - * - BDs/buffers on 60x bus - * - Full duplex - */ -#define CONFIG_SYS_CMXFCR_MASK1 (CMXFCR_FC1 | CMXFCR_RF1CS_MSK | CMXFCR_TF1CS_MSK) -#define CONFIG_SYS_CMXFCR_VALUE1 (CMXFCR_RF1CS_CLK10 | CMXFCR_TF1CS_CLK11) - -#define CONFIG_HAS_ETH1 -#define CONFIG_ETHER_ON_FCC2 1 -/* - Rx clock is CLK13 - * - Tx clock is CLK14 - * - BDs/buffers on 60x bus - * - Full duplex - */ -#define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK) -#define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14) - -#define CONFIG_MII /* MII PHY management */ -#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */ -/* - * GPIO pins used for bit-banged MII communications - */ -#define MDIO_PORT 0 /* Not used - implemented in BCSR */ - -#define MDIO_ACTIVE (*(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFB) -#define MDIO_TRISTATE (*(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x04) -#define MDIO_READ (*(vu_char *)(CONFIG_SYS_BCSR + 8) & 1) - -#define MDIO(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x01; \ - else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFE - -#define MDC(bit) if(bit) *(vu_char *)(CONFIG_SYS_BCSR + 8) |= 0x02; \ - else *(vu_char *)(CONFIG_SYS_BCSR + 8) &= 0xFD - -#define MIIDELAY udelay(1) - -#ifndef CONFIG_8260_CLKIN -#define CONFIG_8260_CLKIN 66000000 /* in Hz */ -#endif - -#define CONFIG_BAUDRATE 38400 - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_ECHO -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_MII -#define CONFIG_CMD_PING - - -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#define CONFIG_BOOTCOMMAND "bootm FF860000" /* autoboot command */ -#define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw mtdparts=phys:7M(root),-(root)ro" - -#if defined(CONFIG_CMD_KGDB) -#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */ -#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */ -#undef CONFIG_KGDB_NONE /* define if kgdb on something else */ -#define CONFIG_KGDB_INDEX 1 /* which serial channel for kgdb */ -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */ -#endif - -#define CONFIG_BZIP2 /* include support for bzip2 compressed images */ -#undef CONFIG_WATCHDOG /* disable platform specific watchdog */ - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } - -#define CONFIG_SYS_FLASH_BASE 0xFF800000 -#define CONFIG_SYS_FLASH_CFI -#define CONFIG_FLASH_CFI_DRIVER -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */ - -#define CONFIG_SYS_DIRECT_FLASH_TFTP - -#if defined(CONFIG_CMD_JFFS2) -#define CONFIG_SYS_JFFS2_FIRST_BANK 0 -#define CONFIG_SYS_JFFS2_NUM_BANKS CONFIG_SYS_MAX_FLASH_BANKS -#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0 -#define CONFIG_SYS_JFFS2_LAST_SECTOR 62 -#define CONFIG_SYS_JFFS2_SORT_FRAGMENTS -#define CONFIG_SYS_JFFS_CUSTOM_PART -#endif - -#if defined(CONFIG_CMD_I2C) -#define CONFIG_HARD_I2C 1 /* To enable I2C support */ -#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed */ -#define CONFIG_SYS_I2C_SLAVE 0x7F /* I2C slave address */ -#endif - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE -#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) -#define CONFIG_SYS_RAMBOOT -#endif - -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */ - -#define CONFIG_ENV_IS_IN_FLASH - -#ifdef CONFIG_ENV_IS_IN_FLASH -#define CONFIG_ENV_SECT_SIZE 0x20000 -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) -#endif /* CONFIG_ENV_IS_IN_FLASH */ - -#define CONFIG_SYS_DEFAULT_IMMR 0x00010000 - -#define CONFIG_SYS_IMMR 0xF0000000 - -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/* Hard reset configuration word */ -#define CONFIG_SYS_HRCW_MASTER 0x0C40025A /* Not used - provided by FPGA */ -/* No slaves */ -#define CONFIG_SYS_HRCW_SLAVE1 0 -#define CONFIG_SYS_HRCW_SLAVE2 0 -#define CONFIG_SYS_HRCW_SLAVE3 0 -#define CONFIG_SYS_HRCW_SLAVE4 0 -#define CONFIG_SYS_HRCW_SLAVE5 0 -#define CONFIG_SYS_HRCW_SLAVE6 0 -#define CONFIG_SYS_HRCW_SLAVE7 0 - -#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPUs */ -#if defined(CONFIG_CMD_KGDB) -# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ -#endif - -#define CONFIG_SYS_HID0_INIT 0 -#define CONFIG_SYS_HID0_FINAL (HID0_ICE | HID0_IFEM | HID0_ABE) - -#define CONFIG_SYS_HID2 0 - -#define CONFIG_SYS_SIUMCR 0x01240200 -#define CONFIG_SYS_SYPCR 0xFFFF0683 -#define CONFIG_SYS_BCR 0x00000000 -#define CONFIG_SYS_SCCR SCCR_DFBRG01 - -#define CONFIG_SYS_RMR RMR_CSRE -#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE) -#define CONFIG_SYS_PISCR (PISCR_PS|PISCR_PTF|PISCR_PTE) -#define CONFIG_SYS_RCCR 0 - -#define CONFIG_SYS_MPTPR 0x1300 -#define CONFIG_SYS_PSDMR 0x82672522 -#define CONFIG_SYS_PSRT 0x4B - -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_BR (CONFIG_SYS_SDRAM_BASE | 0x00001841) -#define CONFIG_SYS_SDRAM_OR 0xFF0030C0 - -#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | 0x00001801) -#define CONFIG_SYS_OR0_PRELIM 0xFF8008C2 -#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_BCSR | 0x00000801) -#define CONFIG_SYS_OR2_PRELIM 0xFFF00864 - -#define CONFIG_SYS_RESET_ADDRESS 0xC0000000 - -#endif /* __CONFIG_H */ |