diff options
Diffstat (limited to 'include/configs/cm_t35.h')
| -rw-r--r-- | include/configs/cm_t35.h | 85 |
1 files changed, 74 insertions, 11 deletions
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index a490fc3..4640c43 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -27,8 +27,6 @@ #define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */ #define CONFIG_OMAP_COMMON -#define CONFIG_SYS_TEXT_BASE 0x80008000 - #define CONFIG_SDRC /* The chip has SDRC controller */ #include <asm/arch/cpu.h> /* get chip and board defs */ @@ -104,8 +102,6 @@ #define CONFIG_USB_OMAP3 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP -#define CONFIG_USB_ULPI -#define CONFIG_USB_ULPI_VIEWPORT_OMAP #define CONFIG_USB_STORAGE #define CONFIG_MUSB_UDC #define CONFIG_TWL4030_USB @@ -115,6 +111,8 @@ #define CONFIG_USB_DEVICE #define CONFIG_USB_TTY #define CONFIG_SYS_CONSOLE_IS_IN_ENV +/* This delay is really for slow-to-power-on USB sticks, not the hub */ +#define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 500 /* commands to include */ #include <config_cmd_default.h> @@ -141,10 +139,10 @@ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 100000 -#define CONFIG_SYS_I2C_SLAVE 1 -#define CONFIG_DRIVER_OMAP34XX_I2C +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 #define CONFIG_I2C_MULTI_BUS @@ -176,7 +174,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ "usbtty=cdc_acm\0" \ - "console=ttyS2,115200n8\0" \ + "console=ttyO2,115200n8\0" \ "mpurate=500\0" \ "vram=12M\0" \ "dvimode=1024x768MR-16@60\0" \ @@ -190,7 +188,6 @@ "mpurate=${mpurate} " \ "vram=${vram} " \ "omapfb.mode=dvi:${dvimode} " \ - "omapfb.debug=y " \ "omapdss.def_disp=${defaultdisplay} " \ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype}\0" \ @@ -198,7 +195,6 @@ "mpurate=${mpurate} " \ "vram=${vram} " \ "omapfb.mode=dvi:${dvimode} " \ - "omapfb.debug=y " \ "omapdss.def_disp=${defaultdisplay} " \ "root=${nandroot} " \ "rootfstype=${nandrootfstype}\0" \ @@ -214,6 +210,7 @@ "nand read ${loadaddr} 2a0000 400000; " \ "bootm ${loadaddr}\0" \ +#define CONFIG_CMD_BOOTZ #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ "if run loadbootscript; then " \ @@ -326,5 +323,71 @@ #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP +#define CONFIG_SCF0403_LCD + +#define CONFIG_OMAP3_SPI + +/* Defines for SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +#define CONFIG_SPL_NAND_SIMPLE + +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1 +#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" + +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBDISK_SUPPORT +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_FAT_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_OMAP3_ID_NAND +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" + +/* NAND boot config */ +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT 64 +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +/* + * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: + * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT + */ +#define CONFIG_SYS_NAND_ECCPOS { 1, 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12 } +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 3 +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define CONFIG_SPL_TEXT_BASE 0x40200800 +#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ +#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK + +/* + * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the + * older x-loader implementations. And move the BSS area so that it + * doesn't overlap with TEXT_BASE. + */ +#define CONFIG_SYS_TEXT_BASE 0x80008000 +#define CONFIG_SPL_BSS_START_ADDR 0x80100000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ + +#define CONFIG_SYS_SPL_MALLOC_START 0x80208000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 #endif /* __CONFIG_H */ |