diff options
Diffstat (limited to 'include/configs/bf533-ezkit.h')
| -rw-r--r-- | include/configs/bf533-ezkit.h | 228 |
1 files changed, 228 insertions, 0 deletions
diff --git a/include/configs/bf533-ezkit.h b/include/configs/bf533-ezkit.h new file mode 100644 index 0000000..7afc1a1 --- /dev/null +++ b/include/configs/bf533-ezkit.h @@ -0,0 +1,228 @@ +/* + * U-boot - Configuration file for BF533 EZKIT board + */ + +#ifndef __CONFIG_EZKIT533_H__ +#define __CONFIG_EZKIT533_H__ + +#define CONFIG_BAUDRATE 57600 +#define CONFIG_STAMP 1 + +#define CONFIG_BOOTDELAY 5 +#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ + +#define CFG_LONGHELP 1 +#define CONFIG_CMDLINE_EDITING 1 +#define CONFIG_LOADADDR 0x01000000 /* default load address */ +#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux" +//#define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw" + +#define CONFIG_DRIVER_SMC91111 1 +#define CONFIG_SMC91111_BASE 0x20310300 + +#if 0 +#define CONFIG_MII +#define CFG_DISCOVER_PHY +#endif + +#define CONFIG_RTC_BFIN 1 +#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ + +/* + * Boot Mode Set + * Blackfin can support several boot modes + */ +#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */ +#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */ +#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */ +/* Define the boot mode */ +#define BFIN_BOOT_MODE BF533_BYPASS_BOOT +//#define BFIN_BOOT_MODE BF533_SPI_BOOT + +#define CONFIG_PANIC_HANG 1 + +#define ADSP_BF531 0x31 +#define ADSP_BF532 0x32 +#define ADSP_BF533 0x33 +#define BFIN_CPU ADSP_BF533 + +/* This sets the default state of the cache on U-Boot's boot */ +#define CONFIG_ICACHE_ON +#define CONFIG_DCACHE_ON + +/* Define where the uboot will be loaded by on-chip boot rom */ +#define APP_ENTRY 0x00001000 + +/* CONFIG_CLKIN_HZ is any value in Hz */ +#define CONFIG_CLKIN_HZ 27000000 +/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ +/* 1=CLKIN/2 */ +#define CONFIG_CLKIN_HALF 0 +/* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ +/* 1=bypass PLL */ +#define CONFIG_PLL_BYPASS 0 +/* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ +/* Values can range from 1-64 */ +#define CONFIG_VCO_MULT 22 +/* CONFIG_CCLK_DIV controls what the core clock divider is */ +/* Values can be 1, 2, 4, or 8 ONLY */ +#define CONFIG_CCLK_DIV 1 +/* CONFIG_SCLK_DIV controls what the peripheral clock divider is */ +/* Values can range from 1-15 */ +#define CONFIG_SCLK_DIV 5 +/* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ +/* Values can range from 2-65535 */ +/* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ +#define CONFIG_SPI_BAUD 2 +#define CONFIG_SPI_BAUD_INITBLOCK 4 + +#if ( CONFIG_CLKIN_HALF == 0 ) +#define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) +#else +#define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) +#endif + +#if (CONFIG_PLL_BYPASS == 0) +#define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) +#define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) +#else +#define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ +#define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ +#endif + +#define CONFIG_MEM_SIZE 32 /* 128, 64, 32, 16 */ +#define CONFIG_MEM_ADD_WDTH 9 /* 8, 9, 10, 11 */ +#define CONFIG_MEM_MT48LC16M16A2TG_75 1 + +#define CONFIG_LOADS_ECHO 1 + + +#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \ + CFG_CMD_PING | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_JFFS2 | \ + CFG_CMD_DATE) +#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600" + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ +#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */ +#define CFG_LOAD_ADDR 0x01000000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */ +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024) +#define CFG_FLASH_BASE 0x20000000 + +#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ +#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN) +#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) +#define CFG_GBL_DATA_SIZE 0x4000 +#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) +#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) + +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CFG_FLASH0_BASE 0x20000000 +#define CFG_FLASH1_BASE 0x20200000 +#define CFG_FLASH2_BASE 0x20280000 +#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */ + +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_ADDR 0x20020000 +#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */ + +/* JFFS Partition offset set */ +#define CFG_JFFS2_FIRST_BANK 0 +#define CFG_JFFS2_NUM_BANKS 1 +/* 512k reserved for u-boot */ +#define CFG_JFFS2_FIRST_SECTOR 11 + + +/* + * Stack sizes + */ +#define CONFIG_STACKSIZE (128*1024) /* regular stack */ + +#define POLL_MODE 1 +#define FLASH_TOT_SECT 40 +#define FLASH_SIZE 0x220000 +#define CFG_FLASH_SIZE 0x220000 + +/* + * Initialize PSD4256 registers for using I2C + */ +#define CONFIG_MISC_INIT_R + +/* + * I2C settings + * By default PF1 is used as SDA and PF0 as SCL on the Stamp board + */ +#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */ +/* + * Software (bit-bang) I2C driver configuration + */ +#define PF_SCL PF0 +#define PF_SDA PF1 + +#define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") +#define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") +#define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") +#define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") +#define I2C_SDA(bit) if(bit) { \ + *pFIO_FLAG_S = PF_SDA; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SDA; \ + asm("ssync;"); \ + } +#define I2C_SCL(bit) if(bit) { \ + *pFIO_FLAG_S = PF_SCL; \ + asm("ssync;"); \ + } \ + else { \ + *pFIO_FLAG_C = PF_SCL; \ + asm("ssync;"); \ + } +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ + +#define CFG_I2C_SPEED 50000 +#define CFG_I2C_SLAVE 0xFE + +#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */ + +/* 0xFF, 0x7BB07BB0, 0x22547BB0 */ +/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN) +#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \ + ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN) +#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \ + B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN) +*/ +#define AMGCTLVAL 0xFF +#define AMBCTL0VAL 0x7BB07BB0 +#define AMBCTL1VAL 0xFFC27BB0 + +#define CONFIG_VDSP 1 + +#ifdef CONFIG_VDSP +#define ET_EXEC_VDSP 0x8 +#define SHT_STRTAB_VDSP 0x1 +#define ELFSHDRSIZE_VDSP 0x2C +#define VDSP_ENTRY_ADDR 0xFFA00000 +#endif + +#endif |