diff options
Diffstat (limited to 'include/configs/barco.h')
| -rw-r--r-- | include/configs/barco.h | 364 |
1 files changed, 364 insertions, 0 deletions
diff --git a/include/configs/barco.h b/include/configs/barco.h new file mode 100644 index 0000000..217c00f --- /dev/null +++ b/include/configs/barco.h @@ -0,0 +1,364 @@ +/******************************************************************** + * + * Unless otherwise specified, Copyright (C) 2004-2005 Barco Control Rooms + * + * $Source: /home/services/cvs/firmware/ppc/u-boot-1.1.2/include/configs/barco.h,v $ + * $Revision: 1.2 $ + * $Author: mleeman $ + * $Date: 2005/02/21 12:48:58 $ + * + * Last ChangeLog Entry + * $Log: barco.h,v $ + * Revision 1.2 2005/02/21 12:48:58 mleeman + * update of copyright years (feedback wd) + * + * Revision 1.1 2005/02/14 09:29:25 mleeman + * moved barcohydra.h to barco.h + * + * Revision 1.4 2005/02/09 12:56:23 mleeman + * add generic header to track changes in sources + * + * + *******************************************************************/ + +/* + * (C) Copyright 2001, 2002 + * Wolfgang Denk, DENX Software Engineering, wd@denx.de. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +/* ------------------------------------------------------------------------- */ + +/* + * board/config.h - configuration options, board specific + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +/* + * High Level Configuration Options + * (easy to change) + */ + +#define CONFIG_MPC824X 1 +#define CONFIG_MPC8245 1 +#define CONFIG_BARCOBCD_STREAMING 1 + +#undef USE_DINK32 + +#define CONFIG_CONS_INDEX 3 /* set to '3' for on-chip DUART */ +#define CONFIG_BAUDRATE 9600 +#define CONFIG_DRAM_SPEED 100 /* MHz */ + +#define CONFIG_BOOTARGS "mem=32M" + +/* Add support for a few extra bootp options like: + * - File size + * - DNS + */ +#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | \ + CONFIG_BOOTP_BOOTFILESIZE | \ + CONFIG_BOOTP_DNS) + +#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \ + CFG_CMD_ELF | \ + CFG_CMD_I2C | \ + CFG_CMD_EEPROM | \ + CFG_CMD_PCI ) + +/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */ +#include <cmd_confdefs.h> + +#define CONFIG_HUSH_PARSER 1 /* use "hush" command parser */ +#define CONFIG_BOOTDELAY 1 +#define CONFIG_BOOTCOMMAND "boot_default" + +/* + * Miscellaneous configurable options + */ +#define CFG_LONGHELP 1 /* undef to save memory */ +#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ +#define CFG_MAXARGS 16 /* max number of command args */ +#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CFG_LOAD_ADDR 0x00100000 /* default load address */ +#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ + + +/*----------------------------------------------------------------------- + * PCI stuff + *----------------------------------------------------------------------- + */ +#define CONFIG_PCI /* include pci support */ +#undef CONFIG_PCI_PNP +#undef CFG_CMD_NET + +#define PCI_ENET0_IOADDR 0x80000000 +#define PCI_ENET0_MEMADDR 0x80000000 +#define PCI_ENET1_IOADDR 0x81000000 +#define PCI_ENET1_MEMADDR 0x81000000 + + +/*----------------------------------------------------------------------- + * Start addresses for the final memory configuration + * (Set up by the startup code) + * Please note that CFG_SDRAM_BASE _must_ start at 0 + */ +#define CFG_SDRAM_BASE 0x00000000 +#define CFG_MAX_RAM_SIZE 0x02000000 + +#define CONFIG_LOGBUFFER +#ifdef CONFIG_LOGBUFFER +#define CFG_STDOUT_ADDR 0x1FFC000 +#else +#define CFG_STDOUT_ADDR 0x2B9000 +#endif + +#define CFG_RESET_ADDRESS 0xFFF00100 + +#if defined (USE_DINK32) +#define CFG_MONITOR_LEN 0x00030000 +#define CFG_MONITOR_BASE 0x00090000 +#define CFG_RAMBOOT 1 +#define CFG_INIT_RAM_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN) +#define CFG_INIT_RAM_END 0x10000 +#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */ +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) +#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#else +#undef CFG_RAMBOOT +#define CFG_MONITOR_LEN 0x00030000 +#define CFG_MONITOR_BASE TEXT_BASE + +#define CFG_GBL_DATA_SIZE 128 + +#define CFG_INIT_RAM_ADDR 0x40000000 +#define CFG_INIT_RAM_END 0x1000 +#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) + +#endif + +#define CFG_FLASH_BASE 0xFFF00000 +#define CFG_FLASH_SIZE (8 * 1024 * 1024) /* Unity has onboard 1MByte flash */ +#define CFG_ENV_IS_IN_FLASH 1 +#define CFG_ENV_OFFSET 0x000047A4 /* Offset of Environment Sector */ +#define CFG_ENV_SIZE 0x00002000 /* Total Size of Environment Sector */ +#define ENV_CRC 0x8BF6F24B + +#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */ + +#define CFG_MEMTEST_START 0x00000000 /* memtest works on */ +#define CFG_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */ + +#define CFG_EUMB_ADDR 0xFDF00000 + +#define CFG_FLASH_RANGE_BASE 0xFFC00000 /* flash memory address range */ +#define CFG_FLASH_RANGE_SIZE 0x00400000 +#define FLASH_BASE0_PRELIM 0xFFF00000 /* sandpoint flash */ +#define FLASH_BASE1_PRELIM 0xFF000000 /* PMC onboard flash */ + +/* + * select i2c support configuration + * + * Supported configurations are {none, software, hardware} drivers. + * If the software driver is chosen, there are some additional + * configuration items that the driver uses to drive the port pins. + */ +#define CONFIG_HARD_I2C 1 /* To enable I2C support */ +#undef CONFIG_SOFT_I2C /* I2C bit-banged */ +#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SLAVE 0x7F + +#ifdef CONFIG_SOFT_I2C +#error "Soft I2C is not configured properly. Please review!" +#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */ +#define I2C_ACTIVE (iop->pdir |= 0x00010000) +#define I2C_TRISTATE (iop->pdir &= ~0x00010000) +#define I2C_READ ((iop->pdat & 0x00010000) != 0) +#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \ + else iop->pdat &= ~0x00010000 +#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \ + else iop->pdat &= ~0x00020000 +#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ +#endif /* CONFIG_SOFT_I2C */ + +#define CFG_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */ +#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 3 +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ + +#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } +#define CFG_FLASH_BANKS { FLASH_BASE0_PRELIM , FLASH_BASE1_PRELIM } +#define CFG_DBUS_SIZE2 1 + +/*----------------------------------------------------------------------- + * Definitions for initial stack pointer and data area (in DPRAM) + */ + + + /* + * NS16550 Configuration (internal DUART) + */ + /* + * Low Level Configuration Settings + * (address mappings, register initial values, etc.) + * You should know what you are doing if you make changes here. + */ + +#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */ + +#define CFG_ROMNAL 0x0F /*rom/flash next access time */ +#define CFG_ROMFAL 0x1E /*rom/flash access time */ + +#define CFG_REFINT 0x8F /* no of clock cycles between CBR refresh cycles */ + +/* the following are for SDRAM only*/ +#define CFG_BSTOPRE 0x25C /* Burst To Precharge, sets open page interval */ +#define CFG_REFREC 8 /* Refresh to activate interval */ +#define CFG_RDLAT 4 /* data latency from read command */ +#define CFG_PRETOACT 3 /* Precharge to activate interval */ +#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */ +#define CFG_ACTORW 2 /* Activate to R/W */ +#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */ +#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */ + +#define CFG_REGISTERD_TYPE_BUFFER 1 +#define CFG_EXTROM 0 +#define CFG_REGDIMM 0 + + +/* memory bank settings*/ +/* + * only bits 20-29 are actually used from these vales to set the + * start/end address the upper two bits will be 0, and the lower 20 + * bits will be set to 0x00000 for a start address, or 0xfffff for an + * end address + */ +#define CFG_BANK0_START 0x00000000 +#define CFG_BANK0_END 0x01FFFFFF +#define CFG_BANK0_ENABLE 1 +#define CFG_BANK1_START 0x02000000 +#define CFG_BANK1_END 0x02ffffff +#define CFG_BANK1_ENABLE 0 +#define CFG_BANK2_START 0x03f00000 +#define CFG_BANK2_END 0x03ffffff +#define CFG_BANK2_ENABLE 0 +#define CFG_BANK3_START 0x04000000 +#define CFG_BANK3_END 0x04ffffff +#define CFG_BANK3_ENABLE 0 +#define CFG_BANK4_START 0x05000000 +#define CFG_BANK4_END 0x05FFFFFF +#define CFG_BANK4_ENABLE 0 +#define CFG_BANK5_START 0x06000000 +#define CFG_BANK5_END 0x06FFFFFF +#define CFG_BANK5_ENABLE 0 +#define CFG_BANK6_START 0x07000000 +#define CFG_BANK6_END 0x07FFFFFF +#define CFG_BANK6_ENABLE 0 +#define CFG_BANK7_START 0x08000000 +#define CFG_BANK7_END 0x08FFFFFF +#define CFG_BANK7_ENABLE 0 +/* + * Memory bank enable bitmask, specifying which of the banks defined above + are actually present. MSB is for bank #7, LSB is for bank #0. + */ +#define CFG_BANK_ENABLE 0x01 + +#define CFG_ODCR 0xff /* configures line driver impedances, */ + /* see 8240 book for bit definitions */ +#define CFG_PGMAX 0x32 /* how long the 8240 retains the */ + /* currently accessed page in memory */ + /* see 8240 book for details */ + +/* SDRAM 0 - 256MB */ +#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) + +/* stack in DCACHE @ 1GB (no backing mem) */ +#if defined(USE_DINK32) +#define CFG_IBAT1L (0x40000000 | BATL_PP_00 ) +#define CFG_IBAT1U (0x40000000 | BATU_BL_128K ) +#else +#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE) +#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) +#endif + +/* PCI memory */ +#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +/* Flash, config addrs, etc */ +#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT) +#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) + +#define CFG_DBAT0L CFG_IBAT0L +#define CFG_DBAT0U CFG_IBAT0U +#define CFG_DBAT1L CFG_IBAT1L +#define CFG_DBAT1U CFG_IBAT1U +#define CFG_DBAT2L CFG_IBAT2L +#define CFG_DBAT2U CFG_IBAT2U +#define CFG_DBAT3L CFG_IBAT3L +#define CFG_DBAT3U CFG_IBAT3U + +/* + * For booting Linux, the board info and command line data + * have to be in the first 8 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +/*----------------------------------------------------------------------- + * FLASH organization + */ +#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_SECT 20 /* max number of sectors on one chip */ + +#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ +#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ + +#define CFG_FLASH_CHECKSUM + +/*----------------------------------------------------------------------- + * Cache Configuration + */ +#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */ +#if (CONFIG_COMMANDS & CFG_CMD_KGDB) +# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +#endif + + +/* + * Internal Definitions + * + * Boot Flags + */ +#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ +#define BOOTFLAG_WARM 0x02 /* Software reboot */ + +/* values according to the manual */ + +#define CONFIG_DRAM_50MHZ 1 +#define CONFIG_SDRAM_50MHZ + +#define CONFIG_DISK_SPINUP_TIME 1000000 + + +#endif /* __CONFIG_H */ |