diff options
Diffstat (limited to 'include/configs/alpr.h')
| -rw-r--r-- | include/configs/alpr.h | 188 |
1 files changed, 92 insertions, 96 deletions
diff --git a/include/configs/alpr.h b/include/configs/alpr.h index c80c76a..e6248e9 100644 --- a/include/configs/alpr.h +++ b/include/configs/alpr.h @@ -40,63 +40,63 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xffe00000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ -#define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ -#define CFG_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ -#define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ -#define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ -#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */ -#define CFG_PCI_MEMBASE1 CFG_PCI_MEMBASE + 0x10000000 -#define CFG_PCI_MEMBASE2 CFG_PCI_MEMBASE1 + 0x10000000 -#define CFG_PCI_MEMBASE3 CFG_PCI_MEMBASE2 + 0x10000000 - - -#define CFG_FPGA_BASE (CFG_PERIPHERAL_BASE + 0x08300000) -#define CFG_NVRAM_BASE_ADDR (CFG_PERIPHERAL_BASE + 0x08000000) +#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ +#define CONFIG_SYS_FLASH_BASE 0xffe00000 /* start of FLASH */ +#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */ +#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */ +#define CONFIG_SYS_PCI_MEMSIZE 0x40000000 /* size of mapped pci memory */ +#define CONFIG_SYS_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ +#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */ +#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */ +#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000 +#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000 + + +#define CONFIG_SYS_FPGA_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x08300000) +#define CONFIG_SYS_NVRAM_BASE_ADDR (CONFIG_SYS_PERIPHERAL_BASE + 0x08000000) /*----------------------------------------------------------------------- * Initial RAM & stack pointer (placed in internal SRAM) *----------------------------------------------------------------------*/ -#define CFG_TEMP_STACK_OCM 1 -#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE -#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */ -#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */ +#define CONFIG_SYS_TEMP_STACK_OCM 1 +#define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_ISRAM_BASE +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */ +#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) -#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 0x4) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/ /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ -#undef CFG_EXT_SERIAL_CLOCK +#undef CONFIG_SYS_EXT_SERIAL_CLOCK #define CONFIG_BAUDRATE 115200 #define CONFIG_UART1_CONSOLE /* define for uart1 as console */ -#define CFG_BAUDRATE_TABLE \ +#define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * FLASH related *----------------------------------------------------------------------*/ -#define CFG_FLASH_CFI 1 /* The flash is CFI compatible */ +#define CONFIG_SYS_FLASH_CFI 1 /* The flash is CFI compatible */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use common CFI driver */ -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ -#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ -#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ -#define CFG_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ +#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */ +#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ +#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */ #define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */ #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ -#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */ /* Address and size of Redundant Environment Sector */ @@ -109,7 +109,7 @@ #undef CONFIG_SPD_EEPROM /* Don't use SPD EEPROM for setup */ #define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0 */ #undef CONFIG_SDRAM_ECC /* enable ECC support */ -#define CFG_SDRAM_TABLE { \ +#define CONFIG_SYS_SDRAM_TABLE { \ {(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \ {(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */ @@ -118,22 +118,21 @@ *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */ +#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */ /*----------------------------------------------------------------------- * I2C EEPROM (PCF8594C) *----------------------------------------------------------------------*/ -#define CFG_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ /* mask of address bits that overflow into the "EEPROM chip address" */ -#define CFG_I2C_EEPROM_ADDR_OVERFLOW 0x07 -#define CFG_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */ /* 8 byte page write mode using */ /* last 3 bits of the address */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */ #define CONFIG_PREBOOT "echo;" \ "echo Type \"run kernelx\" to boot the system;" \ @@ -197,8 +196,9 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ +#define CONFIG_PPC4xx_EMAC #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0x02 /* dummy setting, no EMAC0 used */ @@ -212,7 +212,7 @@ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_M88E1111_PHY 1 /* needed for PHY specific setup*/ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ +#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ #define CONFIG_NETCONSOLE /* include NetConsole support */ @@ -235,43 +235,40 @@ #define CONFIG_CMD_DHCP #define CONFIG_CMD_DIAG #define CONFIG_CMD_EEPROM -#define CONFIG_CMD_ELF #define CONFIG_CMD_FPGA #define CONFIG_CMD_I2C #define CONFIG_CMD_IRQ #define CONFIG_CMD_MII #define CONFIG_CMD_NAND #define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI #define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - +#undef CONFIG_CMD_NFS #undef CONFIG_WATCHDOG /* watchdog disabled */ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_ALT_MEMTEST 1 /* Enable more extensive memtest*/ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_ALT_MEMTEST 1 /* Enable more extensive memtest*/ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ #define CONFIG_LOOPW 1 /* enable loopw command */ @@ -279,7 +276,7 @@ #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ #define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ -#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ +#define CONFIG_SYS_4xx_RESET_TYPE 0x2 /* use chip reset on this board */ /*----------------------------------------------------------------------- * PCI stuff @@ -289,15 +286,15 @@ #define CONFIG_PCI /* include pci support */ #define CONFIG_PCI_PNP /* do pci plug-and-play */ #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ -#define CFG_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE */ +#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */ #define CONFIG_PCI_BOOTDELAY 1 /* enable pci bootdelay variable*/ /* Board-specific PCI */ -#define CFG_PCI_TARGET_INIT /* let board init pci target */ -#define CFG_PCI_MASTER_INIT +#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */ +#define CONFIG_SYS_PCI_MASTER_INIT -#define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ -#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ /*----------------------------------------------------------------------- * FPGA stuff @@ -305,8 +302,8 @@ #define CONFIG_FPGA #define CONFIG_FPGA_ALTERA #define CONFIG_FPGA_CYCLON2 -#define CFG_FPGA_CHECK_CTRLC -#define CFG_FPGA_PROG_FEEDBACK +#define CONFIG_SYS_FPGA_CHECK_CTRLC +#define CONFIG_SYS_FPGA_PROG_FEEDBACK #define CONFIG_FPGA_COUNT 1 /* Ich habe 2 ... aber in Reihe geschaltet -> sollte gehen, aufpassen mit Datasize ist jetzt @@ -315,54 +312,53 @@ Mode erklaert ...*/ /* FPGA program pin configuration */ -#define CFG_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ -#define CFG_GPIO_DATA 19 /* FPGA data pin (cpu output) */ -#define CFG_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ -#define CFG_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ -#define CFG_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ +#define CONFIG_SYS_GPIO_CLK 18 /* FPGA clk pin (cpu output) */ +#define CONFIG_SYS_GPIO_DATA 19 /* FPGA data pin (cpu output) */ +#define CONFIG_SYS_GPIO_STATUS 20 /* FPGA status pin (cpu input) */ +#define CONFIG_SYS_GPIO_CONFIG 21 /* FPGA CONFIG pin (cpu output) */ +#define CONFIG_SYS_GPIO_CON_DON 22 /* FPGA CONFIG_DONE pin (cpu input) */ -#define CFG_GPIO_SEL_DPR 14 /* cpu output */ -#define CFG_GPIO_SEL_AVR 15 /* cpu output */ -#define CFG_GPIO_PROG_EN 23 /* cpu output */ +#define CONFIG_SYS_GPIO_SEL_DPR 14 /* cpu output */ +#define CONFIG_SYS_GPIO_SEL_AVR 15 /* cpu output */ +#define CONFIG_SYS_GPIO_PROG_EN 23 /* cpu output */ /*----------------------------------------------------------------------- * Definitions for GPIO setup *-----------------------------------------------------------------------*/ -#define CFG_GPIO_SHUTDOWN (0x80000000 >> 6) -#define CFG_GPIO_SSD_EMPTY (0x80000000 >> 9) -#define CFG_GPIO_EREADY (0x80000000 >> 26) -#define CFG_GPIO_REV0 (0x80000000 >> 14) -#define CFG_GPIO_REV1 (0x80000000 >> 15) +#define CONFIG_SYS_GPIO_SHUTDOWN (0x80000000 >> 6) +#define CONFIG_SYS_GPIO_SSD_EMPTY (0x80000000 >> 9) +#define CONFIG_SYS_GPIO_EREADY (0x80000000 >> 26) +#define CONFIG_SYS_GPIO_REV0 (0x80000000 >> 14) +#define CONFIG_SYS_GPIO_REV1 (0x80000000 >> 15) /*----------------------------------------------------------------------- * NAND-FLASH stuff *-----------------------------------------------------------------------*/ -#define CFG_MAX_NAND_DEVICE 4 -#define NAND_MAX_CHIPS CFG_MAX_NAND_DEVICE -#define CFG_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ -#define CFG_NAND_BASE_LIST { CFG_NAND_BASE + 0, CFG_NAND_BASE + 2, \ - CFG_NAND_BASE + 4, CFG_NAND_BASE + 6 } -#define CFG_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ +#define CONFIG_SYS_MAX_NAND_DEVICE 4 +#define CONFIG_SYS_NAND_BASE 0xF0000000 /* NAND FLASH Base Address */ +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \ + CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 } +#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */ /*----------------------------------------------------------------------- * External Bus Controller (EBC) Setup *----------------------------------------------------------------------*/ -#define CFG_FLASH CFG_FLASH_BASE +#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */ -#define CFG_EBC_PB0AP 0x92015480 -#define CFG_EBC_PB0CR (CFG_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ +#define CONFIG_SYS_EBC_PB0AP 0x92015480 +#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH | 0x3A000) /* BS=2MB,BU=R/W,BW=16bit */ /* Memory Bank 1 (NAND-FLASH) initialization */ -#define CFG_EBC_PB1AP 0x01840380 /* TWT=3 */ -#define CFG_EBC_PB1CR (CFG_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ +#define CONFIG_SYS_EBC_PB1AP 0x01840380 /* TWT=3 */ +#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_BASE | 0x18000) /* BS=1MB,BU=R/W,BW=8bit */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Internal Definitions |