diff options
Diffstat (limited to 'include/configs/aev.h')
| -rw-r--r-- | include/configs/aev.h | 174 |
1 files changed, 87 insertions, 87 deletions
diff --git a/include/configs/aev.h b/include/configs/aev.h index 2dcaa58..2b4826d 100644 --- a/include/configs/aev.h +++ b/include/configs/aev.h @@ -39,7 +39,7 @@ #define CONFIG_STK52XX 1 /* ... on a STK52XX base board */ #define CONFIG_STK52XX_REV100 1 /* define for revision 100 baseboards */ #define CONFIG_AEVFIFO 1 -#define CFG_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ +#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ @@ -51,7 +51,7 @@ */ #define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */ #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 } /* * PCI Mapping: @@ -74,7 +74,7 @@ #define CONFIG_NET_MULTI 1 #define CONFIG_EEPRO100 1 -#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ +#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */ #define CONFIG_NS8382X 1 #endif /* CONFIG_AEVFIFO */ @@ -84,9 +84,9 @@ #define CONFIG_ISO_PARTITION /* POST support */ -#define CONFIG_POST (CFG_POST_MEMORY | \ - CFG_POST_CPU | \ - CFG_POST_I2C) +#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ + CONFIG_SYS_POST_CPU | \ + CONFIG_SYS_POST_I2C) #ifdef CONFIG_POST /* preserve space for the post_word at end of on-chip SRAM */ @@ -129,7 +129,7 @@ #define CONFIG_TIMESTAMP /* display image timestamps */ #if (TEXT_BASE == 0xFC000000) /* Boot low */ -# define CFG_LOWBOOT 1 +# define CONFIG_SYS_LOWBOOT 1 #endif /* @@ -172,17 +172,17 @@ /* * IPB Bus clocking configuration. */ -#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ +#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */ -#if defined(CFG_IPBCLK_EQUALS_XLBCLK) +#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK) /* * PCI Bus clocking configuration * * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if - * CFG_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock + * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz. */ -#define CFG_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ +#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 /* define for 66MHz speed */ #endif /* @@ -190,9 +190,9 @@ */ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #ifdef CONFIG_TQM5200_REV100 -#define CFG_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ +#define CONFIG_SYS_I2C_MODULE 1 /* Select I2C module #1 for rev. 100 board */ #else -#define CFG_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ +#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #2 for all other revs */ #endif /* @@ -201,11 +201,11 @@ * Please notice, that the resulting clock frequency could differ from the * configured value. This is because the I2C clock is derived from system * clock over a frequency divider with only a few divider values. U-boot - * calculates the best approximation for CFG_I2C_SPEED. However the calculated + * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated * approximation allways lies below the configured value, never above. */ -#define CFG_I2C_SPEED 100000 /* 100 kHz */ -#define CFG_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */ +#define CONFIG_SYS_I2C_SLAVE 0x7F /* * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work @@ -213,34 +213,34 @@ * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the * same configuration could be used. */ -#define CFG_I2C_EEPROM_ADDR 0x50 /* 1010000x */ -#define CFG_I2C_EEPROM_ADDR_LEN 2 -#define CFG_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 20 +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* =32 Bytes per write */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 /* * Flash configuration */ -#define CFG_FLASH_BASE TEXT_BASE /* 0xFC000000 */ +#define CONFIG_SYS_FLASH_BASE TEXT_BASE /* 0xFC000000 */ /* use CFI flash driver if no module variant is spezified */ -#define CFG_FLASH_CFI 1 /* Flash is CFI conformant */ +#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */ #define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */ -#define CFG_FLASH_BANKS_LIST { CFG_BOOTCS_START } -#define CFG_FLASH_EMPTY_INFO -#define CFG_FLASH_SIZE 0x04000000 /* 64 MByte */ -#define CFG_MAX_FLASH_SECT 512 /* max num of sects on one chip */ -#undef CFG_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ - -#if !defined(CFG_LOWBOOT) -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x00760000 + 0x00800000) -#else /* CFG_LOWBOOT */ -#define CONFIG_ENV_ADDR (CFG_FLASH_BASE + 0x00060000) -#endif /* CFG_LOWBOOT */ -#define CFG_MAX_FLASH_BANKS 1 /* max num of flash banks +#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_BOOTCS_START } +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_FLASH_SIZE 0x04000000 /* 64 MByte */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ +#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* not supported yet for AMD */ + +#if !defined(CONFIG_SYS_LOWBOOT) +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000) +#else /* CONFIG_SYS_LOWBOOT */ +#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00060000) +#endif /* CONFIG_SYS_LOWBOOT */ +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks (= chip selects) */ -#define CFG_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ -#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */ /* @@ -255,32 +255,32 @@ /* * Memory map */ -#define CFG_MBAR 0xF0000000 -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_DEFAULT_MBAR 0x80000000 +#define CONFIG_SYS_MBAR 0xF0000000 +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_DEFAULT_MBAR 0x80000000 /* Use ON-Chip SRAM until RAM will be available */ -#define CFG_INIT_RAM_ADDR MPC5XXX_SRAM +#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM #ifdef CONFIG_POST /* preserve space for the post_word at end of on-chip SRAM */ -#define CFG_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_POST_SIZE #else -#define CFG_INIT_RAM_END MPC5XXX_SRAM_SIZE +#define CONFIG_SYS_INIT_RAM_END MPC5XXX_SRAM_SIZE #endif -#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET -#define CFG_MONITOR_BASE TEXT_BASE -#if (CFG_MONITOR_BASE < CFG_FLASH_BASE) -# define CFG_RAMBOOT 1 +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE +#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) +# define CONFIG_SYS_RAMBOOT 1 #endif -#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ -#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /* * Ethernet configuration @@ -318,7 +318,7 @@ * GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST * tests. */ -#define CFG_GPS_PORT_CONFIG 0x81500014 +#define CONFIG_SYS_GPS_PORT_CONFIG 0x81500014 /* * RTC configuration @@ -328,30 +328,30 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ /* Enable an alternate, more extensive memory test */ -#define CFG_ALT_MEMTEST +#define CONFIG_SYS_ALT_MEMTEST -#define CFG_MEMTEST_START 0x00100000 /* memtest works on */ -#define CFG_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ -#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ +#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */ #if defined(CONFIG_CMD_KGDB) -# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */ +# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */ #endif /* @@ -363,22 +363,22 @@ * Various low-level settings */ #if defined(CONFIG_MPC5200) -#define CFG_HID0_INIT HID0_ICE | HID0_ICFI -#define CFG_HID0_FINAL HID0_ICE +#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI +#define CONFIG_SYS_HID0_FINAL HID0_ICE #else -#define CFG_HID0_INIT 0 -#define CFG_HID0_FINAL 0 +#define CONFIG_SYS_HID0_INIT 0 +#define CONFIG_SYS_HID0_FINAL 0 #endif -#define CFG_BOOTCS_START CFG_FLASH_BASE -#define CFG_BOOTCS_SIZE CFG_FLASH_SIZE -#ifdef CFG_PCICLK_EQUALS_IPBCLK_DIV2 -#define CFG_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ +#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE +#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2 +#define CONFIG_SYS_BOOTCS_CFG 0x0008DF30 /* for pci_clk = 66 MHz */ #else -#define CFG_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ +#define CONFIG_SYS_BOOTCS_CFG 0x0004DF30 /* for pci_clk = 33 MHz */ #endif -#define CFG_CS0_START CFG_FLASH_BASE -#define CFG_CS0_SIZE CFG_FLASH_SIZE +#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE #define CONFIG_LAST_STAGE_INIT @@ -386,23 +386,23 @@ * SRAM - Do not map below 2 GB in address space, because this area is used * for SDRAM autosizing. */ -#define CFG_CS2_START 0xE5000000 -#define CFG_CS2_SIZE 0x80000 /* 512 kByte */ -#define CFG_CS2_CFG 0x0004D930 +#define CONFIG_SYS_CS2_START 0xE5000000 +#define CONFIG_SYS_CS2_SIZE 0x80000 /* 512 kByte */ +#define CONFIG_SYS_CS2_CFG 0x0004D930 /* * Grafic controller - Do not map below 2 GB in address space, because this * area is used for SDRAM autosizing. */ #define SM501_FB_BASE 0xE0000000 -#define CFG_CS1_START (SM501_FB_BASE) -#define CFG_CS1_SIZE 0x4000000 /* 64 MByte */ -#define CFG_CS1_CFG 0x8F48FF70 -#define SM501_MMIO_BASE CFG_CS1_START + 0x03E00000 +#define CONFIG_SYS_CS1_START (SM501_FB_BASE) +#define CONFIG_SYS_CS1_SIZE 0x4000000 /* 64 MByte */ +#define CONFIG_SYS_CS1_CFG 0x8F48FF70 +#define SM501_MMIO_BASE CONFIG_SYS_CS1_START + 0x03E00000 -#define CFG_CS_BURST 0x00000000 -#define CFG_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ +#define CONFIG_SYS_CS_BURST 0x00000000 +#define CONFIG_SYS_CS_DEADCYCLE 0x33333311 /* 1 dead cycle for flash and SM501 */ -#define CFG_RESET_ADDRESS 0xff000000 +#define CONFIG_SYS_RESET_ADDRESS 0xff000000 #endif /* __CONFIG_H */ |