diff options
Diffstat (limited to 'include/configs/W7OLMG.h')
| -rw-r--r-- | include/configs/W7OLMG.h | 161 |
1 files changed, 80 insertions, 81 deletions
diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h index 9c5bbff..2260338 100644 --- a/include/configs/W7OLMG.h +++ b/include/configs/W7OLMG.h @@ -63,7 +63,7 @@ #define CONFIG_SERVERIP 192.168.1.2 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#undef CFG_LOADS_BAUD_CHANGE /* disallow baudrate change */ +#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* disallow baudrate change */ #define CONFIG_MII 1 /* MII PHY management */ #define CONFIG_PHY_ADDR 0 /* PHY address */ @@ -71,9 +71,9 @@ #define CONFIG_RTC_M48T35A 1 /* ST Electronics M48 timekeeper */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {2, 4} /* Sensor addresses */ -#define CFG_DTT_MAX_TEMP 70 -#define CFG_DTT_LOW_TEMP -30 -#define CFG_DTT_HYSTERESIS 3 +#define CONFIG_SYS_DTT_MAX_TEMP 70 +#define CONFIG_SYS_DTT_LOW_TEMP -30 +#define CONFIG_SYS_DTT_HYSTERESIS 3 /* @@ -112,38 +112,38 @@ /* * Miscellaneous configurable options */ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ -#undef CFG_HUSH_PARSER /* No hush parse for U-Boot */ -#ifdef CFG_HUSH_PARSER -#define CFG_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_SYS_PROMPT "Wave7Optics> " /* Monitor Command Prompt */ +#undef CONFIG_SYS_HUSH_PARSER /* No hush parse for U-Boot */ +#ifdef CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " #endif #if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ #else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ #endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ +#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ -#undef CFG_EXT_SERIAL_CLOCK /* external serial clock */ -#define CFG_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ -#define CFG_BASE_BAUD 384000 +#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* external serial clock */ +#define CONFIG_SYS_405_UART_ERRATA_59 /* 405GP/CR Rev. D silicon */ +#define CONFIG_SYS_BASE_BAUD 384000 /* The following table includes the supported baudrates */ -#define CFG_BAUDRATE_TABLE {9600} +#define CONFIG_SYS_BAUDRATE_TABLE {9600} -#define CFG_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ +#define CONFIG_SYS_CLKS_IN_HZ 1 /* everything, incl board info, in Hz */ -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* use extended board_info (bd_t) */ +#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ +#define CONFIG_SYS_EXTBDINFO 1 /* use extended board_info (bd_t) */ -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ /*----------------------------------------------------------------------- * PCI stuff @@ -157,14 +157,14 @@ #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */ #define CONFIG_PCI_PNP /* pci plug-and-play */ /* resource configuration */ -#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ -#define CFG_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ -#define CFG_PCI_PTM1LA 0x00000000 /* point to sdram */ -#define CFG_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ -#define CFG_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ -#define CFG_PCI_PTM2LA 0x00000000 /* disabled */ -#define CFG_PCI_PTM2MS 0x00000000 /* disabled */ -#define CFG_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014 /* PCI Vendor ID: IBM */ +#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156 /* PCI Device ID: 405GP */ +#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */ +#define CONFIG_SYS_PCI_PTM1MS 0x80000001 /* 2GB, enable hard-wired to 1 */ +#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */ +#define CONFIG_SYS_PCI_PTM2LA 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2MS 0x00000000 /* disabled */ +#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */ /*----------------------------------------------------------------------- * Set up values for external bus controller @@ -175,94 +175,94 @@ #define CONFIG_USE_PERWE 1 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */ -#define CFG_TEMP_STACK_OCM 1 +#define CONFIG_SYS_TEMP_STACK_OCM 1 /* bank 0 is boot flash */ /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CFG_W7O_EBC_PB0AP 0x03050440 +#define CONFIG_SYS_W7O_EBC_PB0AP 0x03050440 /* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CFG_W7O_EBC_PB0CR 0xFFE38000 +#define CONFIG_SYS_W7O_EBC_PB0CR 0xFFE38000 /* bank 1 is main flash */ /* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CFG_EBC_PB1AP 0x04850240 +#define CONFIG_SYS_EBC_PB1AP 0x04850240 /* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */ -#define CFG_EBC_PB1CR 0xF00FC000 +#define CONFIG_SYS_EBC_PB1CR 0xF00FC000 /* bank 2 is RTC/NVRAM */ /* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CFG_EBC_PB2AP 0x03000440 +#define CONFIG_SYS_EBC_PB2AP 0x03000440 /* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */ -#define CFG_EBC_PB2CR 0xFC018000 +#define CONFIG_SYS_EBC_PB2CR 0xFC018000 /* bank 3 is FPGA 0 */ /* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */ -#define CFG_EBC_PB3AP 0x02000400 +#define CONFIG_SYS_EBC_PB3AP 0x02000400 /* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */ -#define CFG_EBC_PB3CR 0xFD01A000 +#define CONFIG_SYS_EBC_PB3CR 0xFD01A000 /* bank 4 is SAM 8 bit range */ /* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */ -#define CFG_EBC_PB4AP 0x02840380 +#define CONFIG_SYS_EBC_PB4AP 0x02840380 /* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */ -#define CFG_EBC_PB4CR 0xFE878000 +#define CONFIG_SYS_EBC_PB4CR 0xFE878000 /* bank 5 is SAM 16 bit range */ /* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */ -#define CFG_EBC_PB5AP 0x05040d80 +#define CONFIG_SYS_EBC_PB5AP 0x05040d80 /* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */ -#define CFG_EBC_PB5CR 0xFD87A000 +#define CONFIG_SYS_EBC_PB5CR 0xFD87A000 /* bank 6 is unused */ /* pb6ap = 0 */ -#define CFG_EBC_PB6AP 0x00000000 +#define CONFIG_SYS_EBC_PB6AP 0x00000000 /* pb6cr = 0 */ -#define CFG_EBC_PB6CR 0x00000000 +#define CONFIG_SYS_EBC_PB6CR 0x00000000 /* bank 7 is LED register */ /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */ -#define CFG_W7O_EBC_PB7AP 0x03050440 +#define CONFIG_SYS_W7O_EBC_PB7AP 0x03050440 /* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */ -#define CFG_W7O_EBC_PB7CR 0xFE01C000 +#define CONFIG_SYS_W7O_EBC_PB7CR 0xFE01C000 /*----------------------------------------------------------------------- * Start addresses for the final memory configuration * (Set up by the startup code) - * Please note that CFG_SDRAM_BASE _must_ start at 0 + * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 */ -#define CFG_SDRAM_BASE 0x00000000 -#define CFG_FLASH_BASE 0xFFFC0000 -#define CFG_MONITOR_BASE CFG_FLASH_BASE -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ -#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ +#define CONFIG_SYS_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_FLASH_BASE 0xFFFC0000 +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 196 kB for Monitor */ +#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */ /* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ /*----------------------------------------------------------------------- * FLASH organization */ -#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define CFG_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ +#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sec on 1 chip */ -#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ -#define CFG_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ -#define CFG_FLASH_PROTECTION 1 /* Use real Flash protection */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout, Flash Erase, in ms */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout, Flash Write, in ms */ +#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use real Flash protection */ #if 1 /* Use NVRAM for environment variables */ /*----------------------------------------------------------------------- * NVRAM organization */ #define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for env vars */ -#define CFG_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ -#define CFG_NVRAM_SIZE (32*1024) /* NVRAM size */ +#define CONFIG_SYS_NVRAM_BASE_ADDR 0xfc000000 /* NVRAM base address */ +#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */ #define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */ /*define CONFIG_ENV_ADDR \ - (CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ -#define CONFIG_ENV_ADDR CFG_NVRAM_BASE_ADDR + (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env */ +#define CONFIG_ENV_ADDR CONFIG_SYS_NVRAM_BASE_ADDR #else /* Use Boot Flash for environment variables */ /*----------------------------------------------------------------------- @@ -279,14 +279,13 @@ * I2C EEPROM (ATMEL 24C04N) */ #define CONFIG_HARD_I2C 1 /* Hardware assisted I2C */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F - -#define CFG_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ -#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ -#define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_I2C_MULTI_EEPROMS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F + +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM ATMEL 24C04N */ +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */ +#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 +#define CONFIG_SYS_I2C_MULTI_EEPROMS /*----------------------------------------------------------------------- * Definitions for Serial Presence Detect EEPROM address * (to get SDRAM settings) @@ -300,17 +299,17 @@ #define FLASH_BASE1_PRELIM 0xF0000000 /* FLASH bank #1 */ /* On Chip Memory location */ -#define CFG_OCM_DATA_ADDR 0xF8000000 -#define CFG_OCM_DATA_SIZE 0x1000 +#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000 +#define CONFIG_SYS_OCM_DATA_SIZE 0x1000 /*----------------------------------------------------------------------- * Definitions for initial stack pointer and data area (in RAM) */ -#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of SDRAM */ -#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of used area in RAM */ -#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */ +#define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET /* @@ -329,7 +328,7 @@ /* * FPGA(s) configuration */ -#define CFG_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ +#define CONFIG_SYS_FPGA_IMAGE_LEN 0x80000 /* 512KB FPGA image */ #define CONFIG_NUM_FPGAS 1 /* Number of FPGAs on board */ #define CONFIG_MAX_FPGAS 6 /* Maximum number of FPGAs */ #define CONFIG_FPGAS_BASE 0xFD000000L /* Base address of FPGAs */ |